Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Simulation and experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Initial piloted simulation study of geared flap control for tilt-wing V/STOL aircraft

A simulation study of a representative tilt wing transport aircraft was conducted in 1990 on the Ames Vertical Motion Simulator. This simulation is in response to renewed interest in the tilt wing concept for use in future military and civil applications. For past tilt wing concepts, pitch control in hover and low-speed flight has required a tail rotor or reaction jets at the tail. Use of mono cyclic propellers or a geared flap have also been proposed as alternate methods for providing pitch control at low speed. The geared flap is a subject of this current study. This report describes the geared flap concept, the tilt wing aircraft, the simulation model, the simulation facility and experiment setup, the pilots' evaluation tasks and procedures, and the results obtained from the simulation experiment. The pilot evaluations and comments are also documented in the report appendix.

Guerrero, Lourdes M.↗

Validation of high-fidelity ion cyclotron range of frequencies antenna coupling simulations in full 3D geometry against experiments in the ASDEX Upgrade tokamak

We address the validation of finite elements ion cyclotron range of frequencies (ICRF) antenna coupling simulation against experiments performed in the ASDEX Upgrade tokamak. Measurements of the loading resistance in ICRF-heated, magnetically-perturbed 3D plasma discharges are compared against numerical predictions of the RAPLICASOL code. To this end, the 3D induction field and the 3D density profile are modeled by concatenating the PARVMEC, BMW and EMC3-EIRENE codes. The 3D density is input to RAPLICASOL, where full-wave simulations are performed on a finite element mesh retaining full 3D geometry in the ICRF antenna model and the plasma description. The results are further compared with RAPLICASOL simulations using a 1D density profile as measured at the outboard midplane in the same experiments. We find that simulations using a 1D density profile overestimate the change in loading resistance by a factor of ~197 -248%, while simulations using the full 3D density profile are in agreement with experiments within a factor ~16%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Verification of Coupled Hydraulic Fracturing Simulators Using Laboratory-Scale Experiments

In this work, we aim to verify the predictions of the numerical simulators, which are used for designing field-scale hydraulic stimulation experiments. Although a strong theoretical understanding of this process has been gained over the past few decades, numerical predictions of fracture propagation in low-permeability rocks still remains a challenge. Against this background, we performed controlled laboratory-scale hydraulic fracturing experiments in granite samples, which not only provides high-quality experimental data but also a well-characterized experimental set-up. Using the experimental pressure responses and the final fracture sizes as benchmark, we compared the numerical predictions of two coupled hydraulic fracturing simulators—CSMP and GEOS. Both the simulators reproduced the experimental pressure behavior by implementing the physics of Linear Elastic Fracture Mechanics (LEFM) and lubrication theory within a reasonable degree of accuracy. The simulation results indicate that even in the very low-porosity (1–2 %) and low-permeability (10 -18 m 2 - 10 -19 m 2 ) crystalline rocks, which are usually the target of EGS, fluid-loss into the matrix and unsaturated flow impacts the formation breakdown pressure and the post-breakdown pressure trends. Therefore, underestimation of such parameters in numerical modeling can lead to significant underestimation of breakdown pressure. The simulation results also indicate the importance of implementing wellbore solvers for considering the effect of system compressibility and pressure drop due to friction in the injection line. The varying injection rate as a result of decompression at the instant of fracture initiation affects the fracture size, while the entry friction at the connection between the well and the initial notch may cause an increase in the measured breakdown pressure.

15 GEOTHERMAL ENERGY↗

Insights into the structure and dynamics of K + ions at the muscovite–water interface from machine learning potential simulations

The surfaces of many minerals are covered by naturally occurring cations that become partially hydrated and can be replaced by hydronium or other cations when the surface is exposed to water or an aqueous solution. These ion exchange processes are relevant to various chemical and transport phenomena, yet elucidating their microscopic details is challenging for both experiments and simulations. Here, in this work, we make a first step in this direction by investigating the behavior of the native K + ions at the interface between neat water and the muscovite mica (001) surface with ab-initio -based machine learning molecular dynamics and enhanced sampling simulations. Our results show that the desorption of the surface K + ions in pure ion-free water has a significant free energy barrier irrespective of their local surface arrangement. In contrast, facile K + diffusion between mica’s ditrigonal cavities characterized by different Al/Si orderings is observed. This behavior suggests that the K + ions may favor a dynamic disordered surface arrangement rather than complete desorption when exposed to deionized water.

Ab-initio molecular dynamics↗

Data catalog project—A browsable, searchable, metadata system

Modern experiments are typically conducted by large, extended groups, where researchers rely on other team members to produce much of the data they use. The experiments record very large numbers of measurements that can be difficult for users to find, access and understand. Here. we are developing a system for users to annotate their data products with structured metadata, providing data consumers with a discoverable, browsable data index. Machine understandable metadata captures the underlying semantics of the recorded data, which can then be consumed by both programs, and interactively by users. Collaborators can use these metadata to select and understand recorded measurements. The data catalog project is a data dictionary and index which enables users to record general descriptive metadata, use cases and rendering information as well as providing them a transparent data access mechanism (URI). Users describe their diagnostic including references, text descriptions, units, labels, example data instances, author contact information and data access URIs. The list of possible attribute labels is extensible, but limiting the vocabulary of names increases the utility of the system. The data catalog is focused on the data products and complements process-based systems like the Metadata Ontology Provenance project [Greenwald, 2012; Schissel, 2015]. This system can be coupled with MDSplus to provide a simple platform for data driven display and analysis programs. Sites which use MDSplus can describe tree branches, and if desired create ‘processed data trees’ with homogeneous node structures for measurements. Sites not currently using MDSplus can either use the database to reference local data stores, or construct an MDSplus tree whose leaves reference the local data store. A data catalog system can provide a useful roadmap of data acquired from experiments or simulations making it easier for researchers to find and access important data and understand the meaning of the data and how it was obtained. This is particularly useful in research facilities that study the results of many different experiments or simulations and may not know the intricacies of the data organization in use where the data was generated. It is also possible to store a local copy of key data items in local MDSplus trees and then add processed data to the local catalog.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Parallel Operation of Multiple Closely Spaced Small Aspect Ratio Rod Pinches

A series of simulations and experiments to resolve questions about the operation of arrays of closely spaced small aspect ratio rod pinches has been performed. Design and post-shot analysis of the experimental results are supported by 3D particle-in-cell simulations. Both simulations and experiments support these conclusions. Penetration of current to the interior of the array appears to be efficient, as the current on the center rods is essentially equal to the current on the outer rods. Current loss in the feed due to the formation of magnetic nulls was avoided in these experiments by design of the feed surface of the cathode and control of the gap to keep the electric fields on the cathode below the emission threshold. Some asymmetry in the electron flow to the rod was observed, but the flow appeared to symmetrize as it reached the end of the rod. Interaction between the rod pinches can be controlled to allow the stable and consistent operation of arrays of rod pinches.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advanced Modeling and Simulation Methods for Evaluation of Thermal Neutron Scattering Materials

With the rise of interest in thermal neutron scattering data for advanced reactor, criticality safety, and shielding applications, new experimental data are required for evaluation of new materials or for re-evaluation (or validations) of previously evaluated materials. New experimental data are evaluated in a three-step process: (1) computing the phonon characteristics, (2) computing the dynamic structure factor (DSF) from the data, and (3) using the experimental setup to simulate the experimental data. All three steps have challenges, ranging from the need for a sufficiently general material simulation code—a processing code that can compute the corresponding DSF—to having a detailed layout of the instrument/beamline/facility where the data were measured. Whereas phonon characteristics of materials can be computed using various methods (molecular dynamics, density functional theory, etc.), a high-fidelity computation of the DSF and the simulation of the experiment based on the DSF is vital to the accuracy of the evaluation. The latter two steps can be achieved by using the two corresponding code systems developed by instrument scientists at the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory: (1) OCLIMAX, a program that calculates the dynamic structure factor from DFT and MD simulation results, and (2) MCViNE, a Monte Carlo neutron ray-tracing program designed to simulate neutron scattering experiments. Recently, polyethylene and yttrium hydride were measured at the Wide Angular-Range Chopper (ARCS) and SEQUOIA instrument stations of the SNS. These experiments are simulated using the density functional theory code, the Cambridge Serial Total Energy Package (CASTEP), to compute its phonon characteristics (eigenvalues/vectors and PDOS), which is then processed using OCLIMAX to yield the DSF, and finally the data at each instrument station are simulated by the MCViNE for comparison to the measured data for evaluation. For comparison to conventional evaluation methods, the scattering data processed from OCLIMAX are compared against those processed from the LEAPR module of NJOY, and the results from MCViNE simulations are compared against previously used simplified beamline models implemented in the Monte Carlo N-Particle (MCNP) code.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Fluid-phase helium: Shock-compression experiments, quantum molecular dynamics simulations, and development of an equation of state

Helium (He) plays a critical role in numerous areas ranging from the study of celestial objects like brown dwarfs and gas giants to modern-day technologies like nuclear energy and rocket propulsion. For many of these applications, it is essential to have a reliable equation of state (EOS) for He that yields an accurate representation of its thermodynamic behavior. To help constrain and develop such EOS models, we have performed a series of shock-compression experiments on cryogenic liquid He to pressures exceeding 100 GPa using a magnetically accelerated flyer plate on Sandia National Laboratories' Z-machine. We have also performed quantum molecular dynamics simulations that are consistent with our shock measurements. None of the previously available EOSs agree with our experimental and simulation results, motivating the development of a fluid-phase He EOS that we present in this study. Here, we show that our EOS yields good agreement with published data that span temperatures and pressures encountered across a diverse array of applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Virtual experiments: Combining realistic neutron scattering instrument and sample simulations

A new sample component is presented for the Monte Carlo, ray-tracing program, McStas, which is widely used to simulate neutron scattering instruments. The new component allows the sample to be described by its material dynamic structure factor, which is separated into coherent and incoherent contributions. The effects of absorption and multiple scattering are treated and results from simulations and previous experiments are compared. The sample component can also be used to treat any scattering material which may be close to the sample and therefore contaminates the total, measured signal.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Extraction and selective promotion of zero-group velocity and cutoff frequency resonances in bi-dimensional waveguides using the electromechanical impedance method

This study showcases the electromechanical impedance (EMI) technique for extracting and promoting zero-group velocity (ZGV) and cutoff frequency resonances in a waveguide structure. Here, we identify the mechanisms of multiple resonances in the EMI spectra via a wave propagation perspective. Both simulation and experiments reveal the fact that sharp resonances in the conductance spectra are associated with either ZGV or cutoff frequency points. Consequently, we design four test configurations to enhance local resonances by aligning induced motions with considered mode shapes. Reasonable agreement between simulation and experiment results is observed. We evaluate the performance of considered configurations in terms of mode enhancement, and configurations that can selectively promote certain mode families are summarized. This study also shines the light on the EMI technique for quantitative non-destructive evaluation (NDE) by potentially supporting the inverse characterization of mechanical properties of host structures.

42 ENGINEERING↗

Kinetic Growth of Multicomponent Microcompartment Shells

An important goal of systems and synthetic biology is to produce high value chemical species in large quantities. Microcompartments, which are protein nanoshells encapsulating catalytic enzyme cargo, could potentially function as tunable nanobioreactors inside and outside cells to generate these high value species. Modifying the morphology of microcompartments through genetic engineering of shell proteins is one viable strategy to tune cofactor and metabolite access to encapsulated enzymes. However, this is a difficult task without understanding how changing interactions between the many different types of shell proteins and enzymes affect microcompartment assembly and shape. Here, we use multiscale molecular dynamics and experimental data to describe assembly pathways available to microcompartments composed of multiple types of shell proteins with varied interactions. As the average interaction between the enzyme cargo and the multiple types of shell proteins is weakened, the shell assembly pathway transitions from (i) nucleating on the enzyme cargo to (ii) nucleating in the bulk and then binding the cargo as it grows to (iii) an empty shell. Atomistic simulations and experiments using the 1,2-propanediol utilization microcompartment system demonstrate that shell protein interactions are highly varied and consistent with our multicomponent, coarse-grained model. Furthermore, our results suggest that intrinsic bending angles control the size of these microcompartments. Altogether, our simulations and experiments provide guidance to control microcomparmtent size and assembly by modulating the interactions between shell proteins.

defects↗

Piloted Full-Motion Simulation with Simulink®

A recent experiment at NASA Ames Research Center’s Vertical Motion Simulator (VMS) successfully combined a real-time, human in-the-loop architecture with the flexibility of operating in the Simulink® graphical model-based engineering environment. The VMS is a large amplitude flight simulator designed to be adaptable to provide rapid integration and development of a wide variety of vehicles and support diverse aeronautical investigations. Math models are often programmed in Simulink. Typically, to run Simulink models in real time, they are converted to C code. However, the conversion and integration process can be time consuming and cumbersome. Thus, the VMS facility capabilities were expanded to allow a Simulink vehicle math model to run in the MathWorks’ MATLAB environment during a piloted full-motion simulation experiment. The MATLAB Simulink based approach to driving the VMS was found to decrease development time by allowing quick integration of math model changes and providing the ability to run the same version of the model on researcher’s desktop computers. This accomplishment demonstrated that the development ease of the graphical Simulink environment could be retained, while working within the real-time environment of the VMS architecture and maintaining the unique flexibility of the VMS.

hardware in-the-loop↗

Simulating metagenomic stable isotope probing datasets with MetaSIPSim

DNA-stable isotope probing (DNA-SIP) links microorganisms to their in-situ function in diverse environmental samples. Combining DNA-SIP and metagenomics (metagenomic-SIP) allows us to link genomes from complex communities to their specific functions and improves the assembly and binning of these targeted genomes. However, empirical development of metagenomic-SIP methods is hindered by the complexity and cost of these studies. We developed a toolkit, ‘MetaSIPSim,’ to simulate sequencing read libraries for metagenomic-SIP experiments. MetaSIPSim is intended to generate datasets for method development and testing. To this end, we used MetaSIPSim generated data to demonstrate the advantages of metagenomic-SIP over a conventional shotgun metagenomic sequencing experiment. Through simulation we show that metagenomic-SIP improves the assembly and binning of isotopically labeled genomes relative to a conventional metagenomic approach. Improvements were dependent on experimental parameters and on sequencing depth. Community level G + C content impacted the assembly of labeled genomes and subsequent binning, where high community G + C generally reduced the benefits of metagenomic-SIP. Furthermore, when a high proportion of the community is isotopically labeled, the benefits of metagenomic-SIP decline. Finally, the choice of gradient fractions to sequence greatly influences method performance. Metagenomic-SIP is a valuable method for recovering isotopically labeled genomes from complex communities. We show that metagenomic-SIP performance depends on optimization of experimental parameters. MetaSIPSim allows for simulation of metagenomic-SIP datasets which facilitates the optimization and development of metagenomic-SIP experiments and analytical approaches for dealing with these data.

59 BASIC BIOLOGICAL SCIENCES↗

On the characterization of biases arising from methods and approximations used for sensitivity analyses

The preliminary assessment of the performance and safety of advanced reactors, as well as the identification of research and development needs, rely on computer simulations due to the lack of operational experience. Those simulations should be based on verified and validated computational tools, calculation schemes, and nuclear data libraries, and should be accompanied of a proper characterization of the involved uncertainties, providing confidence in the computational-based predictions. Thus, sensitivity and uncertainty studies, together with integral experiments, play an essential role in that process. Sensitivities are then a critical element and guidelines about how to produce accurate enough sensitivities depending on the subsequent analyses to be performed are of interest. The present study addresses the sensitivities biases arising from the use of different nuclear data libraries, computational methods and the assumption of modelling simplifications. Not only sensitivities for multiplication factor but also for safety-relevant reactivity responses have been analyzed. In the study, propagated uncertainties are also included for the considered parameters to illustrate the impact of the sensitivity profiles obtained for each case on the final uncertainty. Then, relevant recommendations are given for sensitivity analyses of highly complex systems. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Dynamic System Simulation of the KRUSTY Experiment

The proposed KRUSTY experiment is a demonstration of a reactor operating at power. The planned experimental configuration includes a highly enriched uranium (HEU) reflected core, cooled by multiple heat pipes leading to Stirling engines for primary heat rejection. Operating power is expected to be approximately four (4) to five (5) kilowatts with a core temperature above 1,000 K. No data is available on any historical reactor employing HEU metal that operated over the temperature range required for the KRUSTY experiment. Further, no reactor has operated with heat pipes as the primary cooling mechanism. Historic power reactors have employed either natural or forced convection so data on their operation is not directly applicable to the KRUSTY experiment. The primary purpose of the system model once developed and refined by data from these component experiments, will be used to plan the KRUSTY experiment. This planning will include expected behavior of the reactor from start-up, through various transient conditions where cooling begins to become present and effective, and finally establishment of steady-state. In addition, the model can provide indicators of anticipated off-normal events and appropriate operator response to those conditions. This information can be used to develop specific experiment operating procedures and aids to guide the operators in conduct of the experiment.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Coupling fast fluid dynamics and multizone airflow models in Modelica Buildings library to simulate the dynamics of HVAC systems

Multizone models are widely used in building airflow and energy performance simulations due to their fast computing speed. However, multizone models assume that the air in a room is well mixed, consequently limiting their application. In specific rooms where this assumption fails, the use of computational fluid dynamics (CFD) models may be an alternative option. Previous research has mainly focused on coupling CFD models and multizone models to study airflow in large spaces. While significant, most of these analyses did not consider the coupled simulation of the building airflow with the building’s Heating, Ventilation, and Air-Conditioning (HVAC) systems. This paper tries to fill the gap by integrating the models for HVAC systems with coupled multizone and CFD simulations for airflows, using the Modelica simulation platform. To improve the computational efficiency, we incorporated a simplified CFD model named fast fluid dynamics (FFD). We first introduce the data synchronization strategy and implementation in Modelica. Then, we verify the implementation using two case studies involving an isothermal and a non-isothermal flow by comparing model simulations to experiment data. Afterward, we study another three cases that are deemed more realistic. Furthermore, this is done by attaching a variable air volume (VAV) terminal box and a VAV system to previous flows to assess the capability of the models in studying the dynamic control of HVAC systems. Finally, we discuss further research needs on the coupled simulation using the models.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Convective transport by intermittent blob-filaments: Comparison of theory and experiment

A blob-filament (or simply ''blob'') is a magnetic-field-aligned plasma structure which is considerably denser than the surrounding background plasma and highly localized in the directions perpendicular to the equilibrium magnetic field B. In experiments and simulations, these intermittent filaments are often formed near the boundary between open and closed field lines, and seem to arise in theory from the saturation process for the dominant edge instabilities and turbulence. Blobs become charge-polarized under the action of an external force which causes unequal drifts on ions and electrons; the resulting polarization-induced E x B drift moves the blobs radially outwards across the scrape-off-layer (SOL). Since confined plasmas generally are subject to radial or outwards expansion forces (e.g., curvature and {nabla}B forces in toroidal plasmas), blob transport is a general phenomenon occurring in nearly all plasmas. This paper reviews the relationship between the experimental and theoretical results on blob formation, dynamics and transport and assesses the degree to which blob theory and simulations can be compared and validated against experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

First-Principles Modeling of IAT-Driven Anomalous Resistivity in Hollow Cathode Discharges II: Numerical Simulations and Comparisons with Experiments

We present a model that quantifies the magnitude of the ion-acoustic turbulence (IAT) in the plume of hollow cathodes and its effect on the resistivity and ion heating. The model takes the form of a partial differential equation (PDE) that can be solved concurrently with the equations of motion for a partially ionized plasma already included in our numerical code for the simulation of the plasma discharge in hollow cathodes, OrCa2D. We also determine that self-induced magnetic fields are not negligible in hollow cathodes operating at large discharge currents and implement in our code Ampere’s law and modifications to Ohm’s law that account for this effect. Numerical simulations that employed these models show large improvements in our agreement with experimental measurements with respect to a previous model, which assumed complete saturation of the IAT and did not account for the growth stage of the waves. In particular, the model is able to accurately predict the location and magnitude of the maximum resitivity to the electron current along the cathode centerline.

Lopez Ortega, Alejandro↗