Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rolling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Apollo-Soyuz test project photographic film processing and sensitometric summary

The Photographic Technology Division at the NASA Lyndon B. Johnson Space Center processed original photographic films exposed in flight during the Apollo Soyuz Test Project (ASTP). Integrated with processing of the original films were strict sensitometric controls and certification procedures established prior to the flight. Information relative to the processing of the 54 rolls of original ASTP flight film and sensitometric data pertinent to each of these rolls of film is presented.

Lockwood, H. E.↗
NASA NTRS1975

Flight test investigation of the vortex wake characteristics behind a Boeing 727 during two-segment and normal ILS approaches

A series of flight tests were performed to evaluate the vortex wake characteristics of a Boeing 727 (B727-200) aircraft during conventional and two-segment ILS approaches. Flights of the B727, equipped with smoke generators for vortex marking, were flown wherein its vortex wake was intentionally encountered by a Lear Jet model 23 (LR-23) or a Piper Twin Comanche (Pa-30); and its vortex location during landing approach was measured using a system of photo-theodolites. The tests showed that at a given separation distance there were no differences in the upsets resulting from deliberate vortex encounters during the two types of approaches. Timed mappings of the position of the landing configuration vortices showed that they tended to descend approximately 91 meters (300 feet) below the flight path of the B727. The flaps of the B727 have a dominant effect on the character of the trailed wake vortex. The clean wing produces a strong, concentrated vortex. As the flaps are lowered, the vortex system becomes more diffuse. Pilot opinion and roll acceleration data indicate that 4.5 nautical miles would be a minimum separation distance at which roll control could be maintained during parallel encounters of the B727's landing configuration wake by small aircraft.

Garodz, L. J.↗
NASA NTRS1976

Low-speed wind-tunnel investigation of various segments of flight spoilers as trailing-vortex-alleviation devices on a transport aircraft model

An investigation was made in the Langley V/STOL tunnel to determine, by the trailing wing sensor technique, the effectiveness of various segments of the existing flight spoilers on a transport aircraft model when they were deflected as trailing-vortex-alleviation devices. The four combinations of flight-spoiler segments investigated were effective in reducing the induced rolling moment on the trailing wing model by as much as 40 to 50 percent at distances behind the transport model of from about 7 to 27 transport wing spans, 27 spans being the downstream limit of distances used in this investigation. Results obtained at about 7 wing spans downstream for two of the spoiler configurations indicate that essentially all the reduction in induced rolling moment on the trailing wing model was realized at a spoiler deflection of about 30 deg.

Croom, D. R.↗
NASA NTRS1976

Wind-Tunnel Investigation of the Effect of Porous Spoilers on the Wake of a Subsonic Transport Model

Tests were conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel to determine how porosity of wing spoilers on a B-747 airplane would affect the rolling moments imposed on an aircraft following in the wake. It was found that spoilers with 40 percent porosity and hole diameter to thickness ratio of 1.1 were just as effective in reducing the rolling moment imposed on the follower as solid spoilers, for the case of two spoilers per wing panel (6.4 percent semispan each) with a following model whose span was 20 percent of the span of the generator. When a larger following model was tested, whose span was 50 percent of that of the generator, the effectiveness of the two spoilers per wing was substantially reduced.

Corsiglia, V. R.↗
NASA NTRS1976

The effect of lateral controls in producing motion of an airplane as computed from wind-tunnel data

An analytical study of the lateral controllability of an airplane has been made in which both the static rolling and yawing moments supplied by the controls and the reactions due to the inherent stability of the airplane have been taken into account. A hypothetical average airplane, embodying the essential characteristics of both the wind tunnel models and the full size test airplanes, was assumed for the study. Computations made of forced rolling and yawing motions of an F-22 airplane caused by a sudden deflection of the ailerons were found to agree well with actual measurements of these motions. The conditions following instantaneous full deflections of the lateral control have been studied, and some attention has been devoted to the controlling of complete turn maneuvers.

Weick, F. E.↗
NASA NTRS1976

Evaluation of ball and roller bearings restored by grinding

The restoration by grinding of those rolling element bearings which are currently being discarded at aircaft engine and transmission overhaul is considered. Three bearing types were selected from the UH-1 helicopter engine and transmission for the pilot program. Groups of each of these bearings were visually and dimensionally inspected for suitability for restoration. A total of 250 bearings were restored by grinding. Of this number, 30 bearings from each type were endurance tested to a TBO of 1600 hours. No bearing failures occurred related to the restoration by grinding process. The two bearing failures which occurred were due to defective rolling elements and were typical of those which may occur in new bearings. The restorable component yield to the three groups was in excess of 90 percent.

Parker, R. J.↗
NASA NTRS1975

A small instrument pointing system for shuttle sortie missions

A small instrument pointing system (SIPS) has been conceptually designed as a means of interfacing smaller astronomical instruments with the ESA spacelab system on shuttle sortie missions. Small instruments are defined as being up to 0.9 meter in diameter, three meters in length, and 340 kilograms in mass. Two independently supported instruments are deployed on a common pedestal to give a hemispherical field of view. The instruments are each supported at their centers-of-mass in bi-axial gimbal systems for fine pointing. An optional roll gimbal can be used to give roll about the line of sight. Instruments are held in environmental canisters which protect them thermally, and acoustically as well as from contamination. The canister facilitates instrument integration and provides interfaces to all spacelab subsystems. The SIPS is a total instrument support system for small sortie mission instruments.

Henrikson, C. C.↗
NASA NTRS1975

Dynamic capacity and surface fatigue life for spur and helical gears

A mathematical model for surface fatigue life of gear, pinion, or entire meshing gear train is given. The theory is based on the statistical approach used by Lundberg and Palmgren for rolling-element bearings. Also equations are presented which give the dynamic capacity of the gear set. The dynamic capacity is the transmitted tangential load which gives a 90 percent probability of survival of the gear set for one million pinion revolutions. The analytical results were compared with test data for a set of AISI 9310 spur gears operating at a maximum Hertz stress of 1.71 billion N per sq m (248,000 psi) and 10,000 rpm. The theoretical life predictions were very good when material constants obtained from rolling-element bearing tests were used in the gear life model.

Coy, J. J.↗
NASA NTRS1975

Aeroelastic stability of trimmed helicopter blades in forward flight

Equations for moderately large amplitude coupled flap-lag motion of a torsionally rigid hingeless elastic helicopter blade in forward flight are derived. Quasi-steady aerodynamic loads are considered and the effects of reversed flow are included. By using Galerkin's method the spatial dependence of the problem is eliminated and the equations are linearized about a time dependent equilibrium position determined from the trimmed equilibrium position of the rotor in forward flight. In the first trim procedure the rotor is maintained at a fixed value of thrust coefficient with forward flight and horizontal and vertical force equilibrium is satisfied in addition to maintaining zero pitch and roll moments. The second trim procedure maintains only zero pitch and roll moment simulating conditions under which a rotor would be tested in the wind tunnel.

Friedmann, P.↗
NASA NTRS1976

The effects of aircraft design and atmospheric turbulence on handling and ride qualities

The effects of aircraft dynamic characteristics on passenger ride quality were investigated to determine ride-quality isocontours similar to aircraft handling-qualities contours. Measurements were made on a motion-base simulator while varying the aircraft short-period and Dutch Roll frequencies and dampings. Both pilot ratings and subjective ride-quality ratings were obtained during simulator flight. Ride and handling qualities were found to be complimentary for the Dutch Roll mode, but not for the short-period mode. Regions of optimal ride and handling qualities were defined for the short-period mode, and the effects of changes in turbulence level studied using mathematical models.

Jones, C. R.↗
NASA NTRS1976

Evaluation of ball and roller bearings restored by grinding

A joint program was undertaken to restore by grinding those rolling-element bearings which are currently being discarded at aircraft engine and transmission overhaul. Three bearing types were selected from the UH-1 helicopter engine (T-53) and transmission for the pilot program. Groups of each of these bearings were visually and dimensionally inspected for suitability for restoration. A total of 250 bearings were restored by grinding. Of this number, 30 bearings from each type were endurance tested to a TBO of 1600 hours. No bearing failures occurred related to the restoration by grinding process. The two bearing failures which occurred were due to defective rolling elements and were typical of those which may occur in new bearings. The restorable component yield to the three groups was in excess of 90 percent.

Parker, R. J.↗
NASA NTRS1976

Application of the nonlinear vortex-lattice concept to aircraft-interference problems

A discrete-vortex model was developed to account for the hazardous effects of the vortex trail issued from the edges of separation of a large leading wing on a small trailing wing. The model is divided into three main parts: the leading wing and its near wake, the near and far wakes of the leading wing, and the trailing wing and the portion of the far wake in its vicinity. The normal force, pitching moment, and rolling moment coefficients for the trailing wing are calculated. The circulation distribution in the vortex trail is calculated in the first part of the model where the leading wing is far upstream and hence is considered isolated. A numerical example is solved to demonstrate the feasibility of using this method to study interference between aircraft. The numerical results show the correct trends: The following wing experiences a loss in lift between the wing-tip vortex systems of the leading wing, a gain outside this region, and strong rolling moments which can change sign as the lateral relative position changes. All the results are strongly dependent on the vertical relative position.

Kandil, O. A.↗
NASA NTRS1976

An investigation of the aerodynamic characteristics of a 0.00548 scale model (model no. 486) of the space shuttle 146-inch diameter solid rocket booster at angels of attack from 113 deg to 180 deg in the AEDC PWT 4-foot transonic wind tunnel (SA16F)

An experimental investigation (SA16F) was conducted in the AEDC PWT 4T to determine the entry static stability of a 0.00548 scale space shuttle solid rocket booster (SRB). The primary objective was to improve the definition of the aerodynamic characteristics in the angle of attack range beyond 90 deg in the vicinity of the entry trim point. The SRB scale model consisted of the reentry configuration with all major protuberances. A simulated heat shield around the engine nozzle was also included. Data were obtained for a 60 deg side mounted sting and a straight nose mounted sting. The angle of attack range for the side mounted sting was 113 deg to 147 deg and for the nose mounted sting 152 deg to 187 deg. The Mach number range consisted of 0.4 to 1.2 at roll angles of 0 and 90 deg. The resulting 6-component aerodynamic force data was presented as the variation of coefficients with angle of attack for each Mach number and roll angle.

Ramsey, P. E.↗
NASA NTRS1976

Long lifetime hollow cathodes for 30-cm mercury ion thrusters

An experimental investigation of hollow cathodes for 30-cm Hg bombardment thrusters was carried out. Both main and neutralizer cathode configurations were tested with both rolled foil inserts coated with low work function material and impregnated porous tungsten inserts. Temperature measurements of an impregnated insert at various positions in the cathode were made. These, along with the cathode thermal profile are presented. A theory for rolled foil and impregnated insert operation and lifetime in hollow cathodes is developed. Several endurance tests, as long as 18000 hours at emission currents of up to 12 amps were attained with no degradation in performance.

Mirtich, M. J.↗
NASA NTRS1976

Flexible, FEP-Teflon covered solar cell module development

Techniques and equipment were developed for the large scale, low-cost fabrication of lightweight, roll-up and fold-up, FEP-Teflon encapsulated solar cell modules. Modules were fabricated by interconnecting solderless single-crystal silicon solar cells and heat laminating them at approximately 300 C between layers of optically clear FEP and to a loadbearing Kapton substrate sheet. Modules were fabricated from both conventional and wraparound contact solar cells. A heat seal technique was developed for mechanically interconnecting modules into an array. The electrical interconnections for both roll-up and fold-up arrays were also developed. The use of parallel-gap resistance welding, ultrasonic bonding, and thermocompression bonding processes for attaching interconnects to solar cells were investigated. Parallel-gap welding was found to be best suited for interconnecting the solderless solar cells into modules. Details of the fabrication equipment, fabrication processes, module and interconnect designs, environmental test equipment, and test results are presented.

Rauschenbach, H. S.↗
NASA NTRS1976

Low-speed wind-tunnel investigation of flight spoilers as trailing-vortex-alleviation devices on a medium range wide-body tri-jet airplane model

An investigation was made in the V/STOL tunnel to determine, by the trailing wing sensor technique, the effectiveness of various segments of the existing flight spoilers on a medium range wide body tri-jet transport airplane model when they were deflected as trailing vortex alleviation devices. The four combinations of flight spoiler segments investigated were effective in reducing the induced rolling moment on the trailing wing model by as much as 15 to 60 percent at distances behind the transport model of from 3.9 to 19.6 transport wing spans, 19.6 spans being the downstream limit of distances used. Essentially all of the reduction in induced rolling moment on the trailing wing model was realized at a spoiler deflection of about 45 deg.

Croom, D. R.↗
NASA NTRS1976

Roller bearing geometry design

A theory of kinematic stabilization of rolling cylinders is extended and applied to the design of cylindrical roller bearings. The kinematic stabilization mechanism puts a reverse skew into the rolling elements by changing the roller taper. Twelve basic bearing modification designs are identified amd modeled. Four have single transverse convex curvature in their rollers while eight have rollers which have compound transverse curvature made up of a central cylindrical band surrounded by symmetric bands with slope and transverse curvature. The bearing designs are modeled for restoring torque per unit axial displacement, contact stress capacity, and contact area including dynamic loading, misalignment sensitivity and roller proportion. Design programs are available which size the single transverse curvature roller designs for a series of roller slopes and load separations and which design the compound roller bearings for a series of slopes and transverse radii of curvature. The compound rollers are proportioned to have equal contact stresses and minimum size. Design examples are also given.

Savage, M.↗
NASA NTRS1976

Low speed wind tunnel investigation of flight spoilers as trailing-vortex-alleviation devices on an extended-range wide body tri-jet airplane model

An investigation was made in the Langley V/STOL tunnel to determine, by the trailing wing sensor technique, the effectiveness of various segments of the existing flight spoilers on an extended-range wide-body tri-jet transport airplane model when they were deflected as trailing-vortex-alleviation devices. On the transport model with the approach flap configuration, the four combinations of flight-spoiler segments investigated were effective in reducing the induced rolling moment on the trailing wing model by as much as 25 to 45 percent at downstream distances behind the transport model of 9.2 and 18.4 transport wing spans. On the transport airplane model with the landing flap configuration, the four combinations of flight-spoiler segments investigated were effective in reducing the induced rolling moment on the trailing wing model by as much as 35 to 60 percent at distances behind the transport model of from 3.7 to 18.4 transport wing spans, 18.4 spans being the downstream limit of distances used.

Croom, D. R.↗