Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Precipitation Science”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Temperature-dependent cyclic response and microstructure of AlSi10Mg(Cu) alloy

Highlights: • The cyclic behavior of AlSi10Mg(Cu) alloy in LCF regime is temperature-dependent. • The transition temperature of the cyclic behavior is about 180 °C. • Microstructure transitions were observed with increasing temperature. - Abstract: In the present work, the cyclic stress response and microstructure evolution of AlSi10Mg(Cu) alloy at high temperature were investigated. Samples were tested at high temperature, under total strain control and tensile-compression loading (R = −1) until failure. The cyclic stress response was analyzed, as well as the microstructures were examined by TEM. The results demonstrated that the cycle stress response of the studied alloy is experimental temperature dependence. Microstructure analysis indicated the precipitated phase was disruptive changed by high temperature compared to the as-received alloy. A lot of coherent β″-Mg{sub 2}Si precipitates and GP zones were observed in the as-received alloy, resulting in sustaining cyclic hardening by pinning effect. At high temperature, the vast majority of the tiny coherency precipitates and clusters transformed to the large semi-coherency Q′ and β′-Mg{sub 2}Si precipitates, leading to the sharp decrease of pinning number and the change of dislocation interaction mechanism, which is believed to be one of the reasons for softening. Another reason is that high temperatures can promote dislocations movement.

36 MATERIALS SCIENCE↗

Effect of annealing after strip casting on microstructure, precipitates and texture in non-oriented silicon steel produced by twin-roll strip casting

Highlights: • Non-oriented silicon steel with superior magnetic properties was produced by twin-roll strip casting. • The effect of annealing after strip casting on microstructure, precipitates and texture was investigated. • Role of precipitates in microstructure and texture evolution along the entire route was explored. • High magnetic induction and strong λ-fiber texture was obtained by optimizing strip annealing process. - Abstract: A 3.1 mm thick non-oriented Fe-1.0% Si steel as-cast strip was produced by twin-roll strip casting. Samples with/without strip annealing were cold rolled to 0.5 mm and then annealed. The development of microstructure, precipitate and texture was characterized along the entire processing route. It was found that annealing after strip casting had a minor influence on the average grain size and texture of the as-cast strip. A large number of particles precipitated and coarsened during the strip annealing process. Meanwhile, precipitates hindered dislocation slip and crystal rotation such that more significant in-grain shear bands were formed in cold rolled sheets. During recrystallization annealing process, the newly formed fine precipitates in directly cold-rolled sheets consumed stored strain energy and also hindered grain growth. But the initial precipitates in the annealed strip grew further and the effect of pinning of dislocations and grain boundary was lost. Therefore, annealed sheets with strip annealing process showed homogeneous equiaxed grains and the recrystallization texture was characterized by strong λ-fiber texture, which led to high permeability.

36 MATERIALS SCIENCE↗

INL Snow Load Methodology White Paper

The purpose of this paper is to provide clarification for applying winter precipitation requirements and guidance as provided in Department of Energy Standard (DOE-STD)-1020-2016 and Nuclear Regulatory Commission (NRC) NUREG-0800. Two snow load methodologies are presented, with selection of the preferred approach for use at Idaho National Laboratory (INL).

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Microstructure and Mechanical Properties of Mg{sub 2}Si/AZ91 Composites In Situ Synthesized by Using Silica Fume as the Si Source

Microstructure and mechanical properties of in situ Mg{sub 2}Si/AZ91 composites fabricated using silica fume as the Si source were investigated. The composites contained α-Mg, network Mg{sub 17}Al{sub 12}, lamellar Mg{sub 17}Al{sub 12}, coarse polygonal Mg{sub 2}Si and needle-type Mg{sub 2}Si. Mischmetal modification eliminated the coarse polygonal Mg{sub 2}Si and resulted in a decreased amount of lamellar Mg{sub 17}Al{sub 12} and refined matrix grain size. Solution and aging treatment made the network Mg{sub 17}Al{sub 12} transform into lamellar Mg{sub 17}Al{sub 12}. As the volume fraction of Mg{sub 2}Si increased, the matrix grain size decreased, the amount of Mg{sub 17}Al{sub 12} increased, and more Mg{sub 17}Al{sub 12} precipitated in grain interiors as a result of the increased Al/Mg ratio caused by increasing the amount of Mg{sub 2}Si. The tensile strength and elastic modulus were much higher for the modified composites than for the unmodified one and increased by both increasing the volume fraction of Mg{sub 2}Si and performing aging treatment. The composites failed in a quasi-cleavage fracture mode, and coarse polygonal Mg{sub 2}Si phases were responsible for the lowest ductility of the unmodified composite. The highest UTS of 291.55 MPa obtained is much higher than those reported so far by using fly ash as the Si source, indicating that silica fume is more suitable as the Si source to synthesize Mg{sub 2}Si/AZ91 composites.

36 MATERIALS SCIENCE↗

Antenna Technology for 3-D Wide Swath Imaging Supporting ACE

A fundamental goal for the National Academy of Sciences Decadal Survey (DS) Aerosol-Cloud-Ecosystems Mission (ACE) is to advance our ability to observe and predict changes to the Earth's hydrological cycle and energy balance in response to climate forcing, especially those changes associated with the effects of aerosol on clouds and precipitation. ACE is focused on obtaining measurements to reduce the uncertainties in current climate models arising from the lack of understanding of aerosol-cloud interactions. As part of the mission instrument suite, the ACE Science Working Group has recommended a dual-frequency radar comprised of a fixed-beam 94 GHz (W-band) radar and a wide-swath 35 GHz (Ka-band) imaging radar. Our ACE radar architecture addresses the challenge associated with achieving the measurement objectives through an innovative, shared aperture antenna that allows dual-frequency radar operation while achieving wide-swath (>100 km) imaging at Ka-band. The antenna system incorporates 2 key technologies; a) a novel dual-band reflector/reflectarray and b) a Ka-band AESA feed module. The benefits of this shared-aperture approach include significant reductions in ACE satellite payload size, weight, and cost while enabling wide-swath imaging at Ka-band. This presentation describes the approach used to develop the reflectarray surface and plans for its TRL maturation.The dual-frequency antenna is comprised of a primary cylindrical reflector/reflectarray surface illuminated by a fixed W-band feed (compatible with a quasi-optical beam waveguide feed, such as that employed on CloudSat) and a Ka-band AESA line feed. The AESA feed design leverages state-of-the-art GaN transmit/receive (T/R) MMICs with high RF output power, high power added efficiency and low noise figure. The innovative reflectarray surface provides beam focusing at W-band, but it is transparent at Ka-band.

RAdar Antenna↗

KS-TmG.1.0

As part of the Pacific Northwest National Laboratory’s (PNNL) Science Focus Area program we are investigating the impact of environmental change on microbial community function in grassland soils. To enable a comprehensive survey of the metabolic potential of complex soil microbiomes, we performed ultra-deep metagenome sequencing, collecting >1 terabase of sequence data from grassland soils representing different precipitation regimes. Intermediate precipitation regime soil (rain-fed and irrigated agriculture) was collected from Konza Prairie Biological Station (KPBS).

54 ENVIRONMENTAL SCIENCES↗

The evolution history of superalloy powders during hot consolidation and plastic deformation

Highlights: • Element segregations in a powder metallurgy superalloy at different states are identified. • The surface energy drives precipitation of oxides, carbides, and γ' particles on powder surface during hot consolidation. • Prior particle boundary structure is distorted and more uniformly refined grains are obtained after hot extrusion. - Abstract: Powder metallurgy superalloys are widely used to produce critical rotating parts in turbine engines. However, the issues like what is the driving force of precipitation on prior particle boundary (PPB) during consolidation and how the PPB structure evolves during plastic deformation still remain to be resolved. In this study, with the characterization of the microstructure evolution from powder, consolidation, to plastic deformation, the segregation of alloying elements on the particle boundaries at elevated temperature was analyzed by equilibrium thermodynamic calculations, and the distortion of PPB structure under large plastic deformation was quantitively simulated by finite element (FE) methods. The results indicated that surface energy serves as the main driving force of PPB precipitation and hot extrusion could distort the PPB structure and yield more uniformly refined grains.

36 MATERIALS SCIENCE↗

Reactive transport modeling to study changes in water chemistry induced by CO2 injection at the Frio-I brine pilot

To demonstrate the potential for geologic storage of CO{sub 2} in saline aquifers, the Frio-I Brine Pilot was conducted, during which 1600 tons of CO{sub 2} were injected into a high-permeability sandstone and the resulting subsurface plume of CO{sub 2} was monitored using a variety of hydrogeological, geophysical, and geochemical techniques. Fluid samples were obtained before CO{sub 2} injection for baseline geochemical characterization, during the CO{sub 2} injection to track its breakthrough at a nearby observation well, and after injection to investigate changes in fluid composition and potential leakage into an overlying zone. Following CO{sub 2} breakthrough at the observation well, brine samples showed sharp drops in pH, pronounced increases in HCO{sub 3}{sup -} and aqueous Fe, and significant shifts in the isotopic compositions of H{sub 2}O and dissolved inorganic carbon. Based on a calibrated 1-D radial flow model, reactive transport modeling was performed for the Frio-I Brine Pilot. A simple kinetic model of Fe release from the solid to aqueous phase was developed, which can reproduce the observed increases in aqueous Fe concentration. Brine samples collected after half a year had lower Fe concentrations due to carbonate precipitation, and this trend can be also captured by our modeling. The paper provides a method for estimating potential mobile Fe inventory, and its bounding concentration in the storage formation from limited observation data. Long-term simulations show that the CO{sub 2} plume gradually spreads outward due to capillary forces, and the gas saturation gradually decreases due to its dissolution and precipitation of carbonates. The gas phase is predicted to disappear after 500 years. Elevated aqueous CO{sub 2} concentrations remain for a longer time, but eventually decrease due to carbonate precipitation. For the Frio-I Brine Pilot, all injected CO{sub 2} could ultimately be sequestered as carbonate minerals.

54 ENVIRONMENTAL SCIENCES↗

Impact of Geoengineering Schemes on the Global Hydrological Cycle

The rapidly rising CO{sub 2} level in the atmosphere has led to proposals of climate stabilization via 'Geoengineering' schemes that would mitigate climate change by intentionally reducing the solar radiation incident on earth's surface. In this paper, we address the impact of these climate stabilization schemes on the global hydrological cycle, using equilibrium simulations from an atmospheric general circulation model coupled to a slab ocean model. We show that insolation reductions sufficient to offset global-scale temperature increases lead to a decrease in the intensity of the global hydrologic cycle. This occurs because solar forcing is more effective in driving changes in global mean evaporation than is CO{sub 2} forcing of a similar magnitude. In the model used here, the hydrologic sensitivity, defined as the percentage change in global mean precipitation per degree warming, is 2.4% for solar forcing, but only 1.5% for CO{sub 2} forcing. Although other models and the climate system itself may differ quantitatively from this result, the conclusion can be understood based on simple considerations of the surface energy budget and thus is likely to be robust. Compared to changing temperature by altering greenhouse gas concentrations, changing temperature by varying insolation results in larger changes in net radiative fluxes at the surface; these are compensated by larger changes in latent and sensible heat fluxes. Hence the hydrological cycle is more sensitive to temperature adjustment via changes in insolation than changes in greenhouse gases. This implies that an alteration in solar forcing might offset temperature changes or hydrological changes from greenhouse warming, but could not cancel both at once.

54 ENVIRONMENTAL SCIENCES↗

TEM study of {beta} Prime precipitate interaction mechanisms with dislocations and {beta} Prime interfaces with the aluminium matrix in Al-Mg-Si alloys

The interaction mechanisms between dislocations and semi-coherent, needle-shaped {beta} Prime precipitates in Al-Mg-Si alloys have been studied by High Resolution Transmission Electron Microscopy (HRTEM). Dislocation loops appearing as broad contrast rings around the precipitate cross-sections were identified in the Al matrix. A size dependency of the interaction mechanism was observed; the precipitates were sheared when the longest dimension of their cross-section was shorter than approximately 15 nm, and looped otherwise. A more narrow ring located between the Al matrix and bulk {beta} Prime indicates the presence of a transition interface layer. Together with the bulk {beta} Prime structure, this was further investigated by High Angle Annular Dark Field Scanning TEM (HAADF-STEM). In the bulk {beta} Prime a higher intensity could be correlated with a third of the Si-columns, as predicted from the published structure. The transition layer incorporates Si columns in the same arrangement as in bulk {beta} Prime , although it is structurally distinct from it. The Z-contrast information and arrangement of these Si-columns demonstrate that they are an extension of the Si-network known to structurally connect all the precipitate phases in the Al-Mg-Si(-Cu) system. The width of the interface layer was estimated to about 1 nm. - Highlights: Black-Right-Pointing-Pointer {beta} Prime is found to be looped at sizes larger than 15 nm (cross section diameter). Black-Right-Pointing-Pointer {beta} Prime is found to be sheared at sizes smaller than 15 nm (cross section diameter). Black-Right-Pointing-Pointer The recently determined crystal structure of {beta} Prime is confirmed by HAADF-STEM. Black-Right-Pointing-Pointer Between {beta} Prime and the Al-matrix a transition layer of about 1 nm is existent. Black-Right-Pointing-Pointer The {beta} Prime /matrix layer is structurally distinct from bulk {beta} Prime and the aluminium matrix.

36 MATERIALS SCIENCE↗

Evaluation of Regional Climate Simulations over the Great Lakes Region Driven by Three Global Data Sets

The performance of regional climate simulations is evaluated for the Great Lakes region. Three 10-year (1990–1999) current-climate simulations are performed using the MM5 regional climate model (RCM) with 36-km horizontal resolution. The simulations employed identical configuration and physical parameterizations, but different lateral boundary conditions and sea-surface temperatures derived from the NCEP Global Reanalysis and output from the CCSM3 and GISS general circulation models (GCMs). The simulation results are compared to the North American Regional Reanalysis (NARR). The three RCM simulations appeared to be more accurate in winter and least accurate in summer, and more accurate aloft than near the surface. The reanalysis-constrained simulation adequately captured the spatial distribution and seasonal cycle of the observed surface-air temperature and precipitation, but it produced consistently across all seasons a cold bias that is generally larger over the lakes than over land and a wet bias due to an overestimation of nonconvective precipitation. The simulated seasonal cycle of moisture–flux convergence over the region was in very good agreement with NARR. The two GCM-driven runs adequately simulated the spatial and seasonal variation of temperature, but overestimated cold-season precipitation and underestimated summer precipitation, reversing the observed annual precipitation cycle. The GISS-driven run failed to simulate the prevailing low-level flow and moisture convergence patterns. All three RCM simulations successfully captured the impact of the Great Lakes on the region's climate, especially on winter precipitation, a significant improvement over coarse-resolution GCM simulations over the region.

54 ENVIRONMENTAL SCIENCES↗

Stereological characterization of the {gamma}' particles in a nickel base superalloy: Comparison between transmission electron microscopy and atomic force microscopy techniques

Critical comparison of transmission electron microscopy and atomic force microscopy techniques was provided concerning size measurements of {gamma}' precipitates in a nickel-base superalloy. The divergence between results is explained in terms of the resolution limit for atomic force microscopy, linked both to the tip dimension and the diameter of the investigated particles.

36 MATERIALS SCIENCE↗

Cement paste prior to setting: A rheological approach

The evolution of cement paste during the dormant period is analyzed via small amplitude oscillation rheological measurements. Cement paste, from the very first moments after mixing cement and water, shows the formation of an elastic gel whose strength is rapidly increasing over time. Up to the onset of Portlandite precipitation G′(t) increases by more than 2 orders of magnitude and in the acceleratory period G′(t) continues steadily to increase. A microstructural modification is likely to occur between the dormant and the acceleratory period. At low deformations in the linearity domain the storage modulus G′(ω) exhibits a negligible frequency dependence. At higher deformations cement paste shows a yield stress which increases on increasing paste concentration. The presence of superplasticizers decreases the yield stress and increases the gelation threshold of the paste. Above the gelation threshold the evolution of cement paste with superplasticizers follows similar trends to the neat paste. -- Highlights: •The gelation of cement paste during the dormant period is analyzed via rheometry. •The observed evolution is proposed to be related to the pore structure refinement. •Similarities are observed with colloidal gels and colloidal glasses.

36 MATERIALS SCIENCE↗

Advancing Organized Convection Representation in the Unified Model: Implementing and Enhancing Multiscale Coherent Structure Parameterization

To address the effect of stratiform latent heating on meso- to large-scale circulations, an enhanced implementation of the Multiscale Coherent Structure Parameterization (MCSP) is developed for the Met Office Unified Model. MCSP represents the top-heavy stratiform latent heating from under-resolved organized convection in general circulation models. We couple the MCSP with a mass-flux convection scheme (CoMorph-A) to improve storm lifecycle continuity. The improved MCSP trigger is specifically designed for mixed-phase deep convective cloud, combined with a background vertical wind shear, both known to be crucial for stratiform development. We also test a cloud top temperature dependent convective-stratiform heating partitioning, in contrast to the earlier fixed partitioning. Assessments from ensemble weather forecasts and decadal simulations demonstrate that MCSP directly reduces cloud deepening and precipitation areas by moderating mesoscale circulations. Indirectly, it amends tropical precipitation biases, notably correcting dry and wet biases over India and the Indian Ocean, respectively. Remarkably, the scheme outperforms a climate model ensemble by improving seasonal precipitation cycle predictions in these regions. The scheme also improves Madden-Julian Oscillation (MJO) spectra, achieving better alignment with observational and reanalysis data by intensifying the simulated MJO over the Indian Ocean during phases 4 to 5. However, the scheme increases precipitation overestimation over the Western Pacific. Shifting from fixed to temperature-dependent convective-stratiform partitioning reduces the Pacific precipitation overestimation and further improves the seasonal cycle in India. Spatially correlated biases highlight the necessity for advances beyond deterministic approaches to align MCSP with environmental conditions.

54 ENVIRONMENTAL SCIENCES↗

Three dimensional microstructural characterization of nanoscale precipitates in AA7075-T651 by focused ion beam (FIB) tomography

The size and distribution of precipitates in Al 7075 alloys affects both the mechanical and corrosion behavior (including stress corrosion cracking and fatigue corrosion) of the alloy. Three dimensional (3D) quantitative microstructural analysis of Al 7075 in the peak aged condition (T651) allows for a better understanding of these behaviors. In this study, Focused ion beam (FIB) tomography was used to characterize the microstructure in three dimensions. Analysis of grains and precipitates was performed in terms of volume, size, and morphology. It was found that the precipitates at the grain boundaries are larger in size, higher in aspect ratios and maximum Feret diameter compared to the precipitates inside the grains, due to earlier nucleation of the precipitates at the grain boundaries. Our data on the precipitates at the interface between grains and Mg{sub 2}Si inclusion show that the surfaces of inclusion (impurity) particles can serve as a location for heterogeneous nucleation of precipitates. - Highlights: •Focused ion beam (FIB) tomography was used to characterize the microstructure of Al 7075 in three dimensions. •Analysis of grains and precipitates was performed in terms of volume, size, and morphology. •Precipitates at the grain boundaries have larger size and aspect ratio compared to the precipitates inside the grains.

36 MATERIALS SCIENCE↗

Spectral Induced Polarization Signatures of Hydroxide Adsorption and Mineral Precipitation in Porous Media

The spectral induced polarization (SIP) technique is a promising approach for delineating subsurface physical and chemical property changes in a minimally invasive manner. To facilitate the understanding of position and chemical properties of reaction fronts that involve mineral precipitation in porous media, we investigated spatiotemporal variations in complex conductivity during evolution of urea hydrolysis and calcite precipitation reaction fronts within a silica gel column. The real and imaginary parts of complex conductivity were shown to be sensitive to changes in both solution chemistry and calcium carbonate precipitation. Distinct changes in imaginary conductivity coincided with increased hydroxide ion concentration during urea hydrolysis. In a separate experiment focused on the effect of hydroxide concentration on interfacial polarization of silica gel and well-sorted sand, we found a significant dependence of the polarization response on pH changes of the solution. We propose a conceptual model describing hydroxide ion adsorption behavior in silica gel and its control on interfacial polarizability. Our results demonstrate the utility of SIP for noninvasive monitoring of reaction fronts, and indicate its potential for quantifying geochemical processes that control the polarization responses of porous media at larger spatial scales in the natural environment.

54 ENVIRONMENTAL SCIENCES↗

Graphene oxide wrapped Ag{sub 3}PO{sub 4} sub-microparticles with highly enhanced photocatalytic activity and stability under visible light irradiation

Highlights: • Graphene oxide wrapped Ag{sub 3}PO{sub 4} sub-microparticles were prepared. • The photocatalytic activity of Ag{sub 3}PO{sub 4} is increased by 6 times by GO wrapping. • The hybrid photocatalysts exhibited excellent stability. - Abstract: Graphene oxide (GO) wrapped Ag{sub 3}PO{sub 4} sub-microparticles were prepared by in situ deposition–precipitation method. By hybridization of Ag{sub 3}PO{sub 4} with GO nanosheets, a 6-fold enhancement in the photodegradation rate toward orange methyl (MO) under visible light irradiation (λ ≥ 420 nm) was observed compared with the pure Ag{sub 3}PO{sub 4} sub-microsparticles. The hybrid photocatalysts also exhibited excellent stability in the successive MO degradation experiments. The highly enhanced photocatalytic activity and stability were mainly attributed to the quick transfer of the photogenerated electrons from Ag{sub 3}PO{sub 4} to GO nanosheets, which could effectively suppress the electron–hole pairs recombination and thus inhibit the photocorrosion of Ag{sub 3}PO{sub 4}. These high-efficient and stable hybrid photocatalysts were expected to show considerable potential applications in wastewater treatment and water splitting.

36 MATERIALS SCIENCE↗

Synthesis and Characterisation of Nanostructured UO{sub 2} Compacts for Separate Effect Investigations

At high burn up nuclear fuel undergoes a significant restructuring, and in particular near the pellet edge, where large 10 μm UO{sub 2} grains of the fresh fuel fragment to yield a material with grain size of 100-300 nm and porosity up to 20%. This so-called 'High Burn up Structure (HBS)' has been investigated in the past to elucidate its morphology, grain size, crystal structure, thermal conductivity, hardness, etc.. Handling of spent fuel, however, is difficult due to its high radioactivity and the concomitant shielding needed to manipulate even the smallest samples. The establishment of a route to prepare a surrogate material closely mimicking the HBS morphology is an essential step, if all the details of this fascinating material are to be understood. Furthermore, preparation of dense bulk nanocrystalline UO{sub 2} as a function of grain size and porosity enables the effect of these crucial parameters to be distinguished, ultimately to provide a full insight into properties of HBS and their detailed assessment. We have successfully produced high density UO{sub 2} disks (φ = 4 mm, h= 1 mm) with grain sizes tunable in the 40 to 1000 nm range, from 10 nm UO{sub 2} powders generated by oxalate precipitation of UO{sub 2} from U(IV) solutions. Consolidation has been achieved using a specially constructed spark plasma sintering (SPS) unit housed in a radiological glovebox, which is equipped with a special die system incorporating SiC inserts to achieve pressures of 500 MPa. The latter innovation has reduced processing times and temperatures, which in turn limits grain growth, but still enabling fully dense compacts to be produced. These results now open the path to determine the potential effect of grain size on mechanical properties, thermal conductivity, irradiation damage (and its recovery), and gas (fission and helium) behaviour therein. Furthermore, using suitable pore formers, samples with controlled porosity to fully emulate the HBS in irradiated fuel can be prepared. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗