SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Dispersion strengthened alloys having the required properties are produced by a process in which the refractory particles are less than 100 to 500 A thick. These are fine enough to ensure the strength characteristics without appreciable degradation of other characteristics. The alloy consists of a matrix metal and a dispersoid metal.
A two-year study of the combustion efficiency of single beryllium droplets burning in a variety of oxidizers (primarily mixtures of oxygen/argon and oxygen/nitrogen) is summarized. An advanced laser heating technique was used to acquire systematic quantitative data on the burning of single beryllium droplets at atmospheric pressure. The research confirmed the sensitivity of beryllium droplet combustion to the chemistry of environmental species and provides experimental documentation for the nitrogen-induced droplet fragmentation of burning beryllium droplets.
The removal of bile acids and cholesterol by polymeric absorption is discussed in terms of micelle-polymer interaction. The results obtained with a polymer composed of 75 parts PEO and 25 parts PB plus curing ingredients show an absorption of 305 to 309%, based on original polymer weight. Particle size effects on absorption rate are analyzed. It is concluded that crosslinked polyethylene oxide polymers will absorb water, crosslinked polybutadiene polymers will absorb lipids; neither polymer will absorb appreciable amounts of lipids from micellar solutions of lipids in water.
Direct current planar magnetron sputtering was used to deposit gold Schottky barrier electrical contacts on n-type GaAs of varying doping densities. The electrical character of the contact was determined from current voltage and electron beam induced voltage data. Without reducing the surface concentration of carbon and oxide, the contacts were found to be rectifying. There is evidence that energetic neutral particles reflected from the magnetron target strike the GaAs and cause interfacial damage similar to that observed for ion sputtering. Particle irradiation of the surface during contact deposition is discussed.
The oxidation of SO2 to sulfate in air at 65 percent relative humidity on carbon particles was investigated gravimetrically in the presence of NO2 and O3. Approximately 1 mg samples of carbon black were exposed to continuously flowing ppbv mixtures of SO2, SO2 + NO2 and SO2 + O3 for prescribed periods of time before desorption into dry N2. Wet chemical analysis of the particles followed desorption. NO2 and O3 were found to have little, if any, effect relative to air on sulfate yields at the concentrations studied.
Based upon recent mechanical property tests a NiAl-AlN composite produced by cryomilling has very attractive high temperature strength. This paper focuses on the oxidation resistance of the NiAl-AlN composite at 1473 and 1573 K as compared to that of Ni-47Al-0.15Zr, one of the most oxidation resistant intermetallics. The results of cyclic oxidation tests show that the NiAl-AlN composite has excellent properties although not quite as good as those of Ni-47Al-0.15Zr. The onset of failure of the NiAl-AlN was unique in that it was not accompanied by a change in scale composition from alumina to less protective oxides. Failure in the composite appears to be related to the entrapment of AlN particles within the alumina scale.
Sieved grain mounts of Apollo 16 drive tube samples have been examined using QEMSCAN - an innovative electron beam technology. By combining multiple energy-dispersive X-ray detectors, fully automated control, and off-line image processing, to produce digital mineral maps of particles exposed on polished surfaces, the result is an unprecedented quantity of mineralogical and petrographic data, on a particle-by-particle basis. Experimental analysis of four size fractions (500-250 microns, 150-90 microns, 75-45 microns and < 20 microns), prepared from two samples (64002,374 and 64002,262), has produced a robust and uniform dataset which allows for the quantification of mineralogy; texture; particle shape, size and density; and the digital classification of distinct particle types in each measured sample. These preliminary data show that there is a decrease in plagioclase modal content and an opposing increase in glass modal content, with decreasing particle size. These findings, together with data on trace phases (metals, sulphides, phosphates, and oxides), provide not only new insights into the make-up of lunar regolith at the Apollo 16 landing site, but also key physical parameters which can be used to design lunar simulants, and compute Figures of Merit for each material produced.
We report low-energy proton and alpha particle SEE data on a 32 nm silicon-on-insulator (SOI) complementary metal oxide semiconductor (CMOS) static random access memory (SRAM) that demonstrates the criticality of understanding and using low-energy protons for SEE testing of highly-scaled technologies
This plan describes the post irradiation examination (PIE) oxidation testing activities to be performed by Oak Ridge National Laboratory (ORNL) on individual particles from Compact 5 4 2 taken from the Advanced Gas Reactor (AGR) experiment, AGR 2. This work will be performed in accordance with the general objectives outlined in the AGR 2 PIE Plan1 and guidance in the ORNL PIE Statement of Work.
This plan describes the post irradiation examination (PIE) oxidation testing activities to be performed by Oak Ridge National Laboratory (ORNL) on individual particles from Compact 5 4 2 taken from the Advanced Gas Reactor (AGR) experiment, AGR 2. This work will be performed in accordance with the general objectives outlined in the AGR 2 PIE Plan1 and guidance in the ORNL PIE Statement of Work.
Metal electrodes deposited in a grid pattern onto flexible polymer substrates have been shown to be a viable alternative to replace indium tin oxide (ITO) as the transparent anode for organic photovoltaics. copper may be a better alternative in terms of cost and stability for large area low-cost solar modules, specifically on roll-to-roll platforms. These customized electrode patterns can be fabricated from copper nanoparticles through various printing techniques applicable to solution phase processing. The Intense Pulsed Light (IPL) technique has been used to sinter copper nanoparticles (~100nm) to fabricate conductive copper electrodes on flexible polymer substrates. However, compared to nanosized (~100 nm) copper particles, microsized (~2 um) copper is much cheaper. In this work, microsized (~2 um) copper is used to produce high conductive copper inks. The conductivity of the print can be adjusted through the use of surfactant. IPL sintering was optimized to obtain high conductivity copper films. In conclusion, several microscopic and electrical spectroscopic characterization techniques such as scanning electron microscopy (SEM), x-ray diffraction (XRD), 4-point probe resistivity measurements were employed to characterize the copper electrodes.
Cadmium selenide (CdSe) quantum dots (Q-dots) were prepared by using non-coordinating solvent octadecene instead of coordinating agent trioctylphosphine oxide (TOPO). Reaction processes were carried out at various temperatures of 240°, 260°, 280° and 300° C under nitrogen atmosphere. The prepared CdSe Q-dots which are highly stable show uniform size distribution and tunable optical absorption and photoluminescence (PL). The growth temperature significantly influenced the particle size; spectral behavior, energy band gap and PL intensity and the full width at half maxima (FWHM). Three different methods were employed to determine the particle size and the average particle size of the CdSe Q-dots is 3.2 - 4.3 nm, grown at different temperatures. In addition, stable and mono-dispersed water soluble CdSe Q-dots were prepared by the ligand exchange technique. Thus, the water soluble Q-dots, which are sensitive to the basic pH may be important for biological applications.
Microwave-initiated ammonia synthesis is a potential candidate to the current Haber-Bosch process that can operate from stranded renewable energy source. Our previous studies indicated Cs-Ru/CeO 2 is a promising catalyst for microwave-assisted ammonia synthesis and the morphology of CeO 2 significantly affects the catalytic performance. In this paper, CeO 2 support with distinct morphologies nanorod, nanoparticle, and microstructure, is studied comprehensively at ambient pressure and low temperature under microwave irradiation. Moreover, CeO 2 nanorods of various sizes were synthesized at different timing (24, 36, and 48 h). Nanorods synthesized at 36 h exhibited superior activity associated to high dispersion and small Ru particle size.
In the photovoltaics industry, the largest market share is represented by solar cells made from multicrystalline silicon, which is grown by directional solidification. During the growth process, the silicon melt is in contact with the silicon nitride coated crucible walls and the furnace atmosphere which contains carbon monoxide. The dissolution of the crucible coating, the carbon bearing gas, and the carbon already present in the feedstock, lead to the precipitation of silicon carbide, and silicon nitride, at later stages of the growth process. The precipitation of Si3N4 and SiC particles of up to several hundred micrometers in diameter leads to severe problems during the wire sawing process for wafering the ingots. Furthermore the growth of the silicon grains can be negatively influenced by the presence of particles, which act as nucleation sources and lead to a grit structure of small grains and are sources for dislocations. If doped with Nitrogen from the dissolved crucible coating, SiC is a semi conductive material, and can act as a shunt, short circuiting parts of the solar cell. For these reasons, the incorporation of such particles needs to be avoided. In this contribution we performed model experiments in which the transport of intentionally added SiC particles and their interaction with the solid-liquid interface during float zone growth of silicon in strong steady magnetic fields was investigated. SiC particles of 7μm and 60μm size are placed in single crystal silicon [100] and [111] rods of 8mm diameter. This is achieved by drilling a hole of 2mm diameter, filling in the particles and closing the hole by melting the surface of the rod until a film of silicon covers the hole. The samples are processed under a vacuum of 1x10(exp -5) mbar or better, to prevent gas inclusions. An oxide layer to suppress Marangoni convection is applied by wet oxidation. Experiments without and with static magnetic field are carried out to investigate the influence of melt convection on the distribution of particles and their incorporation into the crystal. The field strengths applied by a superconducting magnet are 1T, 3T, 4.5T, and 5T. The increase in field strength dampens the melt flow, and so this study provides comparative data to the crystal growth experiment to be carried out onboard the sounding rocket mission TEXUS 51, where purely diffusive growth condition will be achieved under microgravity conditions.
The diffusivity of semivolatile organic compounds (SVOCs) in the bulk particle phase of a viscous atmospheric secondary organic aerosol (SOA) can have a profound impact on aerosol growth and size distribution dynamics. Here, we investigate the bulk diffusivity of SVOCs formed from photo-oxidation of isoprene as they partition to a bimodal aerosol consisting of an Aitken (potassium sulfate) and accumulation mode (aged α-pinene SOA) particles as a function of relative humidity (RH). The model analysis of the observed size distribution evolution shows that liquid-like diffusion coefficient values of D b > 10 –10 cm 2 s –1 fail to explain the growth of the Aitken mode. Instead, much lower values of Db between 2.5 × 10 –15 cm 2 s –1 at 32% RH and 8 × 10 –15 cm 2 s –1 at 82% RH were needed to successfully reproduce the growth of both modes. The diffusivity within the aged α-pinene SOA remains appreciably slow even at 80% RH, resulting in hindered partitioning of SVOCs to large viscous particles and allowing smaller and relatively less viscous particles to effectively absorb the available SVOCs and grow much faster than would be possible otherwise. Our results have important implications for modeling SOA formation and growth in the ambient atmosphere.
Self-assembly of ultrathin Au, W, and Au-W bilayer thin films is investigated using a rapid thermal annealing technique in an inert ambient. The solid-state dewetting of Au films is briefly revisited in order to emphasize the role of initial film thickness. W films deposited onto SiO{sub 2} evolve into needle-like nanocrystals rather than forming particle-like agglomerates upon annealing at elevated temperatures. Transmission electron microscopy reveals that such nanocrystals actually consist of tungsten (VI) oxide (WO{sub 3}) which is related to an anisotropic oxide crystal growth out of the thin film. The evolution of W films is highly sensitive to the presence of any residual oxygen. Combination of both the dewetting of Au and the oxide crystal growth of WO{sub 3} is realized by using various bilayer film configurations of the immiscible Au and W. At low temperature, Au dewetting is initiated while oxide crystal growth is still suppressed. Depending on the stacking sequence of the Au-W bilayer thin film, W acts either as a substrate or as a passivation layer for the dewetting of Au. Being the ground layer, W changes the wettability of Au which clearly modifies its initial state for the dewetting. Being the top layer, W prevents Au from dewetting regardless of Au film thickness. Moreover, regular pattern formation of Au-WO{sub 3} nanoparticles is observed at high temperature demonstrating how bilayer thin film dewetting can create unique nanostructure arrangements.
Microplasma-assisted gas-phase nucleation has emerged as an important new approach to produce high-purity, nanometer-sized, and narrowly dispersed particles. This study aims to integrate this technique with vacuum conditions to enable synthesis and deposition in an ultrahigh vacuum compatible environment. The ultimate goal is to combine nanoparticle synthesis with photoemission spectroscopy-based electronic structure analysis. Such measurements require in vacuo deposition to prevent surface contamination from sample transfer, which can be deleterious for nanoscale materials. A homebuilt microplasma reactor was integrated into an existing atomic layer deposition system attached to a surface science multi-chamber system equipped with photoemission spectroscopy. As proof-of-concept, we studied the decomposition of ferrocene vapor in the microplasma to synthesize iron oxide nanoparticles. The injection parameters were optimized to achieve complete precursor decomposition under vacuum conditions, and nanoparticles were successfully deposited. The stoichiometry of the deposited samples was characterized in situ using X-ray photoelectron spectroscopy indicating that iron oxide was formed. Additional transmission electron spectroscopy characterization allowed the determination of the size, shape, and crystal lattice of the particles, confirming their structural properties.
A simple and efficient synthesis of CuO nanoparticles was carried out by precipitation method using copper metal chips as precursor and sodium hydroxide as a stabilizing agent at different calcinations temperatures (100°C, 150°C, and 175°C). The products were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier Transform Infrared Spectroscopy (FTIR). XRD indicated monoclinic structure of CuO. SEM indicated the variation in nanostructures with the heating temperatures and FTIR inidcated Cu-O stretching frequencies. The CuO nanostructures with the average particle size of about 16.52 nm were prepared at 100°C for 3 hr. When the calcinations temperature was increased to 150°C and 175°C, CuO nanostructures with the particle size of about 17.41 nm, and 18.44 nm were obtained respectively. This aqueous precipitation method can give a large scale production of CuO nanoparticles easily.