Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOADING RATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

Velocity and temperature decay characteristics of inverted-profile jets

In order to design efficient, lightweight flap systems for future engine under-the-wing STOL aircraft, the velocity and temperature decay rate of the jet plume must be increased relative to that for single-stream nozzles in order to provide local flap loads and structural temperatures within acceptable limits. The jet plume decay rate of dual flow engines can be increased by resorting to inverted-profile velocity and temperature nozzle concepts. The peak axial decay characteristics of model-scale, two-stream inverted-profile nozzle flows are empirically correlated. Also discussed are the radial and spreading characteristics of inverted-profile nozzle flows.

Von Glahn, U.↗

Laser velocimeter measurements in shrouded and unshrouded radial flow pump impellers

Shrouded and unshrouded versions of a four-vaned radial flow impeller with a design flow coefficient of 0.063 were tested in a volute pump using a two-component frequency-shifted laser velocimeter. Velocity profiles were measured at six flow rates and at four radial and six circumferential positions in the volute. The variations of the velocity from blade to blade and in the axial direction were measured and are presented. A passage vortex caused by tip leakage and relative casing wall velocity was found in the unshrouded impeller. The tip leakage did not accumulate in the suction wake region; the suction wake region was only 30 to 50 percent as large in the unshrouded impeller as compared to the shrouded impeller. The slip was 30 percent higher in the unshrouded impeller and the variation of slip with flow rate is presented. At no measured position in the impellers did the slip factor reach unity; the closest approach was 0.90. Reverse loadings of the vanes at outer radii were found for flow rates below the impeller/volute matching point for both impellers.

Hamkins, C. P.↗

A finite viscoelastic constitutive model for low to high strain rate response of elastomers with application of strain rate-induced glass transition

Amorphous elastomers exhibit significant rate-stiffening and unique viscous flow characteristics across a wide range of strain rates, often undergoing glass transition above a strain rate threshold. We have developed a thermodynamically-consistent and micromechanically-inspired constitutive model for soft elastomeric materials to capture the rate-dependent stress-strain behavior and hysteresis when subjected to low to high strain rates. Here, our proposed constitutive model encapsulates the viscous flow of materials through molecular motion at low strain rates and local rearrangement and alignment of the molecules trying to overcome the intermolecular resistance at high strain rates, essentially covering the glass transition. We applied our constitutive model to uniaxial compression experiments performed at low and high strain rates for polyborosiloxane (PBS) to identify the material parameters, and subsequently, performed numerical simulations of single and multi-cycle compression, stress relaxation, and small amplitude oscillatory tension-compression. Our analyses indicate that the model predicts higher total energy dissipation with increasing strain rate; however, dissipation associated with molecular relaxation decreases (forming a cusp) because, beyond a crossover strain rate, intermolecular rearrangement and alignment become dominant, which is consistent with the onset of the glass transition. For cyclic loading-unloading, we observed that dissipation over a cycle remains constant at low strain rates but decreases non-monotonically at high strain rates before becoming constant, with the peak stress over the cycle becoming higher, which can be interpreted as more loading being carried elastically by the polymer network as the intermolecular rearrangement process occurs. Additionally, our model was able to predict the qualitative nature of the storage modulus and loss modulus in the limit of small strain over a wide range of frequency sweeps.

36 MATERIALS SCIENCE↗

Designing Lithium–Sulfur Batteries with High-Loading Cathodes at a Lean Electrolyte Condition

Developing lithium–sulfur cells with a high-loading cathode at a lean-electrolyte condition is the key to bringing the lithium–sulfur technology into the energy-storage market. However, it has proven to be extremely challenging to develop a cell that simultaneously satisfies the abovementioned metrics while also displaying high electrochemical efficiency and stability. Here, we present a concept of constructing a conductive cathode substrate with a low surface area and optimized nanoporosity (i.e., limited micropores in the porous matrix) that enables achieving a high sulfur loading of 13 mg cm –2 and a high sulfur content of 75 wt % with an extremely low electrolyte/sulfur ratio of just 4.0 μL mg –1 . The high-loading nanocomposite cathodes demonstrate high-areal capacities of 9.3 mA h cm –2 , high energy densities of 18.6 mW h cm –2 , and superior cyclability with excellent capacity retention of 85% after 200 cycles. These values are higher than the benchmarks set up for developing future commercial lithium–sulfur cells (i.e., areal capacity of >2–4 mA h cm –2 , energy density of >8–13 mW h cm –2 , and a long cycle life of 200 cycles with a capacity retention of 80%). The cathode design further exhibits high-rate capability from C/20 to 1 C rates and great potential to attain ultrahigh sulfur loading and a content of 17 mg cm –2 and 80 wt %. Furthermore, the key nanostructural feature that enables realizing fast-charge transport is the low surface area and limited microporosity that avoid the fast consumption of the electrolyte during cell cycling.

25 ENERGY STORAGE↗

Simulation fidelity and numerosity effects in CDTI experimentation

Twenty pilot workload assessment techniques were compared using a simulated flying task in which three levels of psychomotor workload were imposed. The experiment was conducted in a three degree of freedom motion base simulator. Opinion measures, spare mental capacity measures, physiological measures, eye movement behavior and primary task performance measures were evaluated. The primary task was an instrument landing system (ILS) approach and landing. All measures were recorded between the outer and middle markers on the approach. Three levels of psychomotor load were obtained by the combined manipulation of wind gust disturbance level and simulated aircraft pitch stability. Six instrument rated general aviation pilots participated in the experiment. Cooper-Harper ratings, WCI/TE ratings, time estimation standard deviation, pulse rate mean, and control movements per unit time demonstrated sensitivity to psychomotor load. No intrusion into primary task performance was found that the sensitivities of workload estimation techniques vary widely, and that only a few techniques appear to be sensitive to psychomotor load.

Kreifeldt, J. G.↗

Use of blade pitch control to provide power train damping for the Mod-2, 2.5-mW wind turbine

The Control System for the Mod-2 wind turbine system is required to provide not only for startup, RPM regulation, maximizing or regulating power, and stopping the rotor, but also for load limiting, especially in the power train. Early operations with above-rated winds revealed an instability which was caused primarily by coupling between the quill shaft and the rotor air loads. This instability caused the first of several major Mod-2 Control System changes which are reviewed in the paper.

Blissell, W. A., Jr.↗

Unveiling the origins of work-hardening enhancement and mechanical instability in laser shock peened titanium

Laser shock-peening (LSP) produces complex gradients in microstructures and residual stresses, which enables fabrication of metallic engineering components with superior mechanical properties. In this work, we use non-destructive and spatially resolved high-energy X-ray diffraction (HE-XRD) to investigate the influences of LSP on microstructure, surface topography, and residual stress for high purity titanium plates. LSP is found to produce large compressive in-plane residual stresses near the peened surface which monotonically decay to zero about 2.5 mm below the surface. These properties were also tracked during in-situ tensile loading, allowing stress partitioning and work-hardening rates to be measured as a function of depth. The surface region is found to have the highest work-hardening rate and remain mechanically stable up to sample failure. In addition, a crystal rigid rotation along a transversal axis of about 27 & nbsp; was observed at large applied strain near the surface region, which is attributed to the formation of denser dispersed shear bands. Furthermore, a sudden drop in tensile stress was observed at a depth of similar to 160 mu m from the LSP surface, indicating the formation of a localized mechanical instability zone (LMIZ). The origin of this LMIZ could be attributed to the increase in shear stress induced by a load transfer from LSP surface due to the formation of denser dispersed shear bands. These observations indicate a localized transition in deformation behavior has occurred from dispersed shear banding to LMIZ and homogeneous deformation.

36 MATERIALS SCIENCE↗

The deformation and acoustic emission of aluminum-magnesium alloy under non-isothermal thermo-mechanical loading

The following study investigates the deformation behavior and acoustic emission in aluminum-magnesium alloy under conditions of non-isothermal thermo-mechanical loading. The accumulation of deformation in the alloy, in conditions of change from room temperature to 500°C, occurs in two temperature intervals (I, II), characterized by different rates of deformation. The rate of deformation accumulation is correlated with acoustic emission. With load increasing in cycles from 40 to 200 MPa, the value of the boundary temperature (T{sub b}) between intervals I and II changes non-monotonically. In cycles with load up to 90 MPa, the T{sub b} value increases, while an increase up to 200 MPa makes T{sub b} shift toward lower temperatures. This suggests that the shift of boundaries in the region of low temperatures and the appearance of high-amplitude pulses of acoustic emission characterize the decrease of the magnitude of thermal fluctuations with increasing mechanical load, leading to the rupture of interatomic bonds in an elementary deformation act.

36 MATERIALS SCIENCE↗

Finite element analysis of instability-related delamination growth

A parametric study of postbuckled through-width delaminations in laminated coupons was performed. A finite element analysis was developed to analyze the coupons as a combination of linear and geometrically nonlinear components. Because most of the coupon configuration studied behaves linearly, the mixed linear and nonlinear analysis greatly reduced computational costs. The analysis was verified by comparing numerical with exact solutions for simple hypothetical problems. In addition, measured lateral deflections of postbuckled through-width delaminations in laminated coupons were compared with predicted deflections. In the parametric study, stress distributions and strain-energy release rates were calculated for various delamination lengths, delamination depths, applied loads, and lateral deflections. Also, a small number of coupons with through-width delaminations were fatigue tested to obtain delamination growth data. Calculated strain-energy release rates were compared with the observed growth rates to determine the relative importance of the Mode 1 and Mode 2 components of energy release. Growth process was dominated by G sub I.

Whitcomb, J. D.↗

Modelling the Thermo-Mechanical Behavior of Magnesium Alloys during Indirect Extrusion

One of the basic metal forming process for semi-finished products is extrusion. Since extrusion involves complex thermo-mechanical and multiaxial loading conditions resulting in large strains, high strain rates and an increase in temperature due to deformation, a proper yield criterion and hardening law should be used in the numerical modelling of the process. A phenomenological model based on a plastic potential has been proposed that takes strain, strain rate and temperature dependency on flow behaviour into consideration. A hybrid methodology of experiment and finite element simulation has been adopted in order to obtain necessary model parameters. The anisotropy/asymmetry in yielding was quantified by tensile and compression tests of specimens prepared from different directions. The identification of the corresponding model parameters was performed by a genetic algorithm. A fully coupled thermo-mechanical analysis has been used in extrusion simulations for calculation of the temperature field by considering heat fluxes and heat generated due to plastic deformation. The results of the approach adopted in this study appeared to be successful showing promising predictions of the experiments and thus may be extended to be applicable to other magnesium alloys or even other hcp metals.

36 MATERIALS SCIENCE↗

INVESTIGATION OF A TEST LOOP FOR THE COOLING SYSTEM OF THE ITER TF COIL UNDER PULSED HEAT LOAD

CEA is involved in the design of the cooling scheme of the future ITER tokamak. Pulsed operation of ITER will result in heat load variations (which refrigerators have difficulties to cope with). A load smoothing device has been proposed by the ITER team which needs to be validated. To do this, a scaled-down experiment (hereafter also called model) has been proposed and studied in the framework of an EFDA sub-task. This paper presents the test loop dimensioning and the preliminary design for constructing the model. The choice of the relevant design criteria had to be defined so as to obtain in fine a geometric ratio between the ITER system and the model. It is shown that this ratio is then applicable for the mass flow rates as well as the different volumes (heat exchanger, pipes,...) existing on ITER and on the proposed experimental model. Details of the scaling, model design and 3D views corresponding to this preliminary study are presented in this paper.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Ultrahigh strain-rate bending of copper nanopillars with laser-generated shock waves

An experimental study to bend FIB-prepared cantilevered single crystal Cu nanopillars of several hundred nanometers in diameter and length at ultrahigh strain rate is presented. The deformation is induced by laser-generated stress waves, resulting in local strain rates exceeding 10{sup 7} s{sup −1}. Loading of nano-scale Cu structures at these extremely short loading times shows unique deformation characteristics. At a nominal stress value of 297 MPa, TEM examination along with selected area electron diffraction characterization revealed that twins within the unshocked Cu pillars interacted with dislocations that nucleated from free surfaces of the pillars to form new subgrain boundaries. MD simulation results were found to be consistent with the very low values of the stress required for dislocation activation and nucleation because of the extremely high surface area to volume ratio of the nanopillars. Specifically, simulations show that the stress required to nucleate dislocations at these ultrahigh strain rates is about one order of magnitude smaller than typical values required for homogeneous nucleation of dislocation loops in bulk copper single crystals under quasi-static conditions.

36 MATERIALS SCIENCE↗

Effects of Aging-Time Reference on the Long Term Behavior of the IM7/K3B Composite

An analytical study was undertaken to investigate the effects of the time-based shift reference on the long term behavior of the graphite reinforced thermoplastic polyimide composite IM7/K3B at elevated temperature. Creep compliance and the effects of physical aging on the time dependent response was measured for uniaxial loading at several isothermal conditions below the glass transition temperature (T(sub g). Two matrix dominated loading modes, shear and transverse, were investigated in tension and compression. The momentary sequenced creep/aging curves were collapsed through a horizontal (time) shift using the shortest, middle and longest aging time curve as the reference curve. Linear viscoelasticity was used to characterize the creep/recovery behavior and superposition techniques were used to establish the physical aging related material constants. The use of effective time expressions in a laminated plate model allowed for the prediction of long term creep compliance. The effect of using different reference curves with time/aging-time superposition was most sensitive to the physical aging shift rate at lower test temperatures. Depending on the loading mode, the reference curve used can result in a more accurate long term prediction, especially at lower test temperatures.

Veazie, David R.↗

Rate Dependent Multi-Mechanism Discharge of Ag 0.50 VOP 4 ·1.8H 2 O: Insights from In Situ Energy Dispersive X-ray Diffraction

Ag 0.50 VOPO 4 ·1.8H 2 O (silver vanadium phosphate, SVOP) demonstrates a counterintuitive higher initial loaded voltage under higher discharge current. Energy dispersive X-ray diffraction (EDXRD) from synchrotron radiation was used to create tomographic profiles of cathodes at various depths of discharge for two discharge rates. SVOP displays two reduction mechanisms, reduction of a vanadium center accompanied by lithiation of the structure, or reduction-displacement of a silver cation to form silver metal. In-situ EDXRD provides the opportunity to observe spatially resolved changes to the parent SVOP crystal and formation of Ag 0 during reduction. At a C/170 discharge rate V 5+ reduction is the preferred initial reaction resulting in higher initial loaded voltage. At a discharge rate of C/400 reduction of Ag + with formation of conductive Ag 0 occurs earlier during discharge. Discharge rate also affects the spatial location of reduction products. The faster discharge rate initiates reduction close to the current collector with non-uniform distribution of silver metal resulting in isolated cathode areas. The slower rate develops a more homogenous distribution of reduced SVOP and silver metal. This study illuminates the roles of electronic and ionic conductivity limitations within a cathode at the mesoscale and how they impact the course of reduction processes and loaded voltage.

25 ENERGY STORAGE↗

Uncertainty Error Modeling for Non-Linear State Estimation With Unsynchronized SCADA and µPMU Measurements

Distribution systems of the future smart grid require enhancements to the reliability of distribution system state estimation (DSSE) in the face of low measurement redundancy, unsynchronized measurements, and dynamic load profiles. Micro phasor measurement units (µPMUs) facilitate co-synchronized measurements with high granularity, albeit at an often prohibitively expensive installation cost. Supervisory control and data acquisition (SCADA) measurements can supplement µPMU data, although they are received at a slower sampling rate. Further complicating matters is the uncertainty associated with load dynamics and unsynchronized measurements–not only are the SCADA and µPMU measurements not synchronized with each other, but the SCADA measurements themselves are received at different time intervals with respect to one another. This paper proposes a non-linear state estimation framework which models dynamic load uncertainty error by updating the variances of the unsynchronized measurements, leading to a time-varying system of weights in the weighted least squares state estimator. Case studies are performed on the 33-Bus Distribution System in MATPOWER, using Ornstein–Uhlenbeck stochastic processes to simulate dynamic load conditions.

Cooper, Austin↗

The influence of temperature on fatigue crack growth in a mill annealed Ti-6Al-4V alloy.

To study the influence of temperature on the rate of fatigue crack growth in high strength metal alloys, constant load amplitude fatigue crack growth experiments were carried out using a .25-in.-thick mill annealed Ti-6Al-4V alloy plate. The rates of fatigue crack growth were determined as a function of temperature, ranging from room temperature to about 290 C, and as a function of the crack tip stress intensity factor in a dehumidified high purity argon environment. Limited correlative experiments were carried out in distilled water, dehumidified oxygen and hydrogen, and in vacuum. The results indicate that the rate of fatigue crack growth is essentially independent of test temperature in this alloy, and is affected by residual moisture in very small concentrations. Companion fractographic examinations suggest that the mechanims for fatigue crack growth in the various environments are essentially the same.

Wei, R. P.↗

Variable Emissivity Through MEMS Technology

This paper discusses a new technology for variable emissivity (vari-e) radiator surfaces, which has significant advantages over traditional radiators and promises an alternative design technique for future spacecraft thermal control systems. All spacecraft rely on radiative surfaces to dissipate waste heat. These radiators have special coatings, typically with a low solar absorptivity and a high infrared-red emissivity, that are intended to optimize performance under the expected heat load and thermal sink environment. The dynamics of the heat loads and thermal environment make it a challenge to properly size the radiator and often require some means of regulating the heat rejection rate of the radiators in order to achieve proper thermal balance. Specialized thermal control coatings, which can passively or actively adjust their emissivity offer an attractive solution to these design challenges. Such systems would allow intelligent control of the rate of heat loss from a radiator in response to heat load and thermal environmental variations. Intelligent thermal control through variable emissivity systems is well suited for nano and pico spacecraft applications where large thermal fluctuations are expected due to the small thermal mass and limited electric resources. Presently there are three different types of vari-e technologies under development: Micro ElectroMechanical Systems (MEMS) louvers, Electrochromic devices, and Electrophoretic devices. This paper will describe several prototypes of micromachined (MEMS) louvers and experimental results for the emissivity variations measured on theses prototypes. It will further discuss possible actuation mechanisms and space reliability aspects for different designs. Finally, for comparison parametric evaluations of the thermal performances of the new vari-e technology and standard thermal control systems are presented in this paper.

Darrin, Ann Garrison↗

Baseline Design of a Hurricane-Resilient Wind Turbine (Poster)

Under U.S. Department of Energy-sponsored research FOA 415, the National Renewable Energy Laboratory led a team of research groups to produce a complete design of a large wind turbine system to be deployable in the western Gulf of Mexico region. As such, the turbine and its support structure would be subjected to hurricane-loading conditions. Among the goals of this research was the exploration of advanced and innovative configurations that would help decrease the levelized cost of energy (LCOE) of the design, and the expansion of the basic IEC design load cases (DLCs) to include hurricane environmental conditions. The wind turbine chosen was a three-bladed, downwind, direct-drive, 10-MW rated machine. The rotor blade was optimized based on an IEC load suite analysis. The drivetrain and nacelle components were scaled up from a smaller sized turbine using industry best practices. The tubular steel tower was sized using ultimate load values derived from the rotor optimization analysis. The substructure is an innovative battered and raked jacket structure. The innovative turbine has also been modeled within an aero-servo-hydro-elastic tool, and future papers will discuss results of the dynamic response analysis for select DLCs. Although multiple design iterations could not be performed because of limited resources in this study, and are left to future research, the obtained data will offer a good indication of the expected LCOE for large offshore wind turbines to be deployed in subtropical U.S. waters, and the impact design innovations can have on this value.

17 WIND ENERGY↗