Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Exchange”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99

A novel shallow bore ground heat exchanger for ground source heat pump applications—Model development and validation

A novel ground heat exchanger design, the Underground Thermal Battery (UTB), was proposed as a low-cost alternative to the conventional vertical bore ground heat exchanger (VBGHE) for the application of ground source heat pumps (GSHPs). The UTB is designed to be installed in a shallow borehole (less than 6 m deep) and thus could cost much less than the conventional VBGHE, which usually is installed in vertical bores 60 m deep. By utilizing natural convection of water and phase change materials, the UTB tempers its temperature change in response to thermal loads, which helps improve the efficiency of GSHPs. A one-dimensional (1D) model of the UTB has been developed and validated with the measured performance data of a small-scale UTB, as well as the simulation results of a more detailed three dimensional (3D) numerical model, which accounts for both heat transfer and fluid dynamics in the UTB. Further, this 1D model is computationally much more efficient than the 3D model and thus can simulate the annual performance of the UTB with acceptable computation time. The 1D model has been used to evaluate the performance of the UTB so that it can be compared with the conventional VBGHE.

42 ENGINEERING↗

Transition-metal doped titanate nanowire photocatalysts boosted by selective ion-exchange induced defect engineering

Defect engineering through elemental doping is an efficient way to boost the performance of semiconductor photocatalysts. For this work, transition-metal (TM) doped titanate nanowires (TNWs) were prepared via ion-exchange over the titanate precursors and demonstrated for the Rhodamine B (RhB) degradation under ultraviolet (UV) light irradiation. The ion-exchange of selective ions (V 5+ , Cr 3+ , Ni 2+ , and Zn 2+ ) with protons from pristine TNWs resulted in the hierarchical meso-porosity of nanowires with large pores of ~5–20 nm by TM doping and small pores of ~3.6–4.5 nm inherited from pristine TNWs, which facilitates the mass transfer while maintaining high surface area and active sites. Meanwhile, the TM intercalation partially reduces the Ti 4+ to Ti 3+ and narrows the optical bandgap, which, together with oxygen vacancies and superoxide radicals from pristine TNWs, enhance the adsorption and photocatalytic degradation performance of RhB. This work helps to elucidate the effects of transition-metal doping and provides a rational strategy towards high performance titanate-based photocatalysts for efficient and sustainable wastewater treatment.

36 MATERIALS SCIENCE↗

Human kidney anion exchanger 1 interacts with kinesin family member 3B (KIF3B)

Highlights: {yields} Impaired trafficking of kAE1 causes distal renal tubular acidosis (dRTA). {yields} The interaction between kAE1 and kinesin family member 3B (KIF3B) is reported. {yields} The co-localization between kAE and KIF3B was detected in human kidney tissues. {yields} A marked reduction of kAE1 on the cell membrane was observed when KIF3B was knockdown. {yields} KFI3B plays an important role in trafficking of kAE1 to the plasma membrane. -- Abstract: Impaired trafficking of human kidney anion exchanger 1 (kAE1) to the basolateral membrane of {alpha}-intercalated cells of the kidney collecting duct leads to the defect of the Cl{sup -}/HCO{sub 3}{sup -} exchange and the failure of proton (H{sup +}) secretion at the apical membrane of these cells, causing distal renal tubular acidosis (dRTA). In the sorting process, kAE1 interacts with AP-1 mu1A, a subunit of AP-1A adaptor complex. However, it is not known whether kAE1 interacts with motor proteins in its trafficking process to the plasma membrane or not. We report here that kAE1 interacts with kinesin family member 3B (KIF3B) in kidney cells and a dileucine motif at the carboxyl terminus of kAE1 contributes to this interaction. We have also demonstrated that kAE1 co-localizes with KIF3B in human kidney tissues and the suppression of endogenous KIF3B in HEK293T cells by small interfering RNA (siRNA) decreases membrane localization of kAE1 but increases its intracellular accumulation. All results suggest that KIF3B is involved in the trafficking of kAE1 to the plasma membrane of human kidney {alpha}-intercalated cells.

60 APPLIED LIFE SCIENCES↗

Tailoring catalyst layer structures for anion exchange membrane fuel cells by controlling the size of ionomer aggreates in dispersion

The development of anion exchange membranes and ionomers plays a critical role in performance of anion exchange membrane fuel cells. However, the optimal design of catalyst layer structures still remains unexplored despite its significance. Herein, the rational design guide is presented for cathode and anode catalyst layers using m-TPN1 ionomer by controlling the size of ionomer aggregates in dispersion and comparing various catalyst layer structures. The size of m-TPN1 aggregates decreases, creating a more uniform ionomer distribution and a larger triple-phase-boundary. As ionomer distribution of the cathode catalyst layer becomes more uniform, the power density of membrane-electrode-assembly is enhanced. Also, the power density at fully humidified condition strongly correlates with the porosity of anode catalyst layer due to the limitation of hydrogen transport at anode by water flooding.

42 ENGINEERING↗

Buried interface modulation via $\mathrm{PEDOT:PSS}$ ionic exchange for the Sn-Pb mixed perovskite based solar cells

To apply Sn-Pb mixed perovskite solar cells for highly efficient single- or multi-junction devices, understanding device-specific buried interfaces is necessary. Poly [3,4-ethylenedioxythiophene]:poly[styrene sulfonate] (PEDOT:PSS) is primarily used as a hole transport layer in Sn-Pb mixed perovskite solar cells. However, the spatial heterogeneity of PEDOT:PSS, caused by its PEDOT-rich and PSS-rich domains, induces many defects at the buried interface in PEDOT:PSS/perovskite, which limits device performance. Here, we present ionic exchange (IE) of PEDOT:PSS via a combination of methylamine iodide (MAI) and dimethyl sulfoxide (DMSO). Through surface analyses and density functional theory (DFT) simulations, we confirm that the IE process preferentially form PEDOT-I and MA-PSS and that PSS-rich domains bind to DMSO. Thus, the spatial separation of PEDOT:PSS is solved, and the exchanged MA + and I - ions serve as a bridge between PEDOT:PSS and the perovskite, leading to improved physical, chemical, and electrical properties of the buried interface. The Sn-Pb mixed perovskite solar cells using IE-PEDOT:PSS achieve an improved efficiency of 21.3% with an open-circuit voltage of 0.85 V and show better long-term stability. Additionally, IE-PEDOT:PSS works effectively in 2-terminal all-perovskite tandem devices, resulting in an improved efficiency of 23.5% and high reproducibility.

14 SOLAR ENERGY↗

Selective phosphate removal with manganese oxide composite anion exchange membranes in membrane capacitive deionization

The discharge of excessive phosphorous into water bodies can lead to serious eutrophication threatening aquatic ecosystem. Membrane capacitive deionization (MCDI) is an effective platform for deionizing aqueous streams; however, conventional MCDI is unable to selectively remove targeted ions from a liquid mixture. Here, in this work, we fabricated manganese oxide composite anion exchange membranes (AEMs) for MCDI to enhance phosphate removal selectivity from sodium chloride-sodium dihydrogen phosphate (10:1 M ratio) aqueous mixtures. We systematically investigated several critical factors, such as constant current or voltage operation, applied voltage amount, process stream pH, and manganese oxide (Mn 2 O 3 ) content in the AEM, on phosphate removal efficiency and phosphate selectivity. A trade-off was observed between phosphate removal and selectivity when increasing the cell voltage. Under the best conditions, a MCDI unit with a 20 wt% Mn 2 O 3 composite AEM and a bipolar membrane facilitated high phosphate removal efficiency of ≥ 31.8 % and a phosphate over chloride selectivity of 1.1 while showing stability for at least 30 cycles. To help understand how Mn 2 O 3 composite AEM boosts phosphate selectivity, static electronic structure calculations were performed, and they revelated that hydrogen phosphate absorption on Mn 2 O 3 composite AEM was 314 kcal/mol more exothermic than that on pristine AEM while chloride adsorption on Mn 2 O 3 composite AEM was 2.2 kcal/mol less exothermic than that on a pristine AEM. Overall, this work presents an effective strategy for selectively removing phosphate from model wastewater solutions and the mechanistic understanding that governs ion selectivity in composite ion-exchange membranes used in MCDI.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The anion exchange properties of AFm (hydrocalumite-group) minerals defined from solubility experiments and crystallographic information

Solubility experiments with binary series of OH-, Cl-, SO{sub 4}- and CO{sub 3}-AFm were re-examined with a non-ideal, multicomponent solid solution model. The electrical double layer on the mineral's outer surface, which neutralizes about 5% of the anionic charge, can be included. The choice of the end-members in the solid solution and the reaction formulation can help to eliminate the ‘non-ideality’ for OH-SO{sub 4} and Cl-OH exchange. CO{sub 3}-Cl-OH exchange is not ideal in the solubility experiments, nor can it be, because the mineral volume is not a linear combination of the end-members. The solubilities of the end-members are related to the anion charge and inversely to the anion-layer thickness. OH is part of the anion-charge, even when a pure, other anion form is the target of the synthesis. Pure OH-AFm is unstable and converts into hydrogarnet and portlandite, depending on the precipitation rate of hydrogarnet.

36 MATERIALS SCIENCE↗

Impact of hydrophobic pendant phenyl groups on transport and co-transport of methanol and acetate in PEGDA-SPMAK cation exchange membranes

CO 2 reduction cells are innovative devices that reduce CO 2 into valuable chemicals (i.e. methanol (MeOH) and acetate (OAc – )) on the cathode. A major challenge with such devices is to develop ion exchange membranes that allow ion-selective transport (i.e., protons for cation exchange membranes, CEM) and suppress the crossover of CO 2 reduction products. To design such membranes, it is important to understand multi-solute transport behavior of these solutes. Previously, our group reported acetate diffusivities in co-transport with MeOH increase in sulfonated CEMs, where we speculated charge screening of the electrostatic interactions by co-diffusing MeOH has an impact. Here, crosslinked membranes fabricated by photopolymerization of poly(ethylene glycol) diacrylate (PEGDA), 3-sulfopropyl methacrylate potassium (SPMAK, SO 3 – -containing ionomer), and a phenyl-containing comonomer either phenoxyethyl acrylate (PEA) or poly(ethylene glycol) phenyl ether acrylate (PEGPEA)) are investigated. We observe OAc – diffusivities to both (1) PEGDA-SPMAK and (2) PEGDA-PEGPEA increase in co-diffusion with MeOH and those to (3) PEGDA-SPMAK/PEGPEA decrease. To rationalize this emergent co-transport behavior, we speculate (1) electrostatic interactions are interfered with by co-diffusing MeOH, (2) chain mobility (segmental dynamics) increases in the presence of MeOH and (3) for films with both hydrophobic (PEGPEA) and hydrophilic (SPMAK) comonomers chain mobility (segmental dynamics) decrease due to interactions between the comonomer sidechains depressing overall solute diffusivities. Finally, while further investigations are needed, this work contributes to improving our fundamental understanding of the relationships between polymer film chemistry, solute chemistry, and emergent cotransport behavior observed and described in this work (and others) towards enabling the design of improved membrane materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Current research in low temperature proton exchange membrane-based electrolysis and a necessary shift in focus

While hydrogen has limited use in energy markets today, significant growth is possible in grid storage and as an energy carrier in other sectors. Along with lower electricity prices, further hydrogen cost reduction can enable electrochemical water splitting, particularly as the use of intermittent, renewable power sources increases and the quantity and duration of storage requirements limit electrical storage options. With the improved viability of large-scale hydrogen production, research in low temperature electrolysis has dramatically increased. The overwhelming majority of research efforts within proton exchange membrane-based systems has focused on catalyst development, although a smaller set have developed transport layers as well. As proton exchange membrane-based electrolysis shifts into higher technology readiness levels, however, there is a growing need for work optimizing materials integration, developing component-specific and device-level accelerated stress tests, and addressing manufacturing considerations. These areas directly impact electrolyzer performance, durability, and cost, and are critical to advancing hydrogen’s value and electrochemical water splitting.

08 HYDROGEN↗

Heat transfer coefficients of shell and coiled tube heat exchangers

In the present study, the heat transfer coefficients of shell and helically coiled tube heat exchangers were investigated experimentally. Three heat exchangers with different coil pitches were selected as test section for both parallel-flow and counter-flow configurations. All the required parameters like inlet and outlet temperatures of tube-side and shell-side fluids, flow rate of fluids, etc. were measured using appropriate instruments. Totally, 75 test runs were performed from which the tube-side and shell-side heat transfer coefficients were calculated. Empirical correlations were proposed for shell-side and tube-side. The calculated heat transfer coefficients of tube-side were also compared to the existing correlations for other boundary conditions and a reasonable agreement was observed. (author)

42 ENGINEERING↗

Experimental study on corrugated cross-flow air-cooled plate heat exchangers

Experimental study on cross-flow air-cooled plate heat exchangers (PHEs) was performed. The two prototype PHEs were manufactured in a stack of single-wave plates and double-wave plates in parallel. Cooling air flows through the PHEs in a crosswise direction against internal cooling water. The heat exchanger aims to substitute open-loop cooling towers with closed-loop water circulation, which guarantees cleanliness and compactness. In this study, the prototype PHEs were tested in a laboratory scale experiments. From the tests, double-wave PHE shows approximately 50% enhanced heat transfer performance compared to single-wave PHE. However, double-wave PHE costs 30% additional pressure drop. For commercialization, a wide channel design for air flow would be essential for reliable performance. (author)

42 ENGINEERING↗

Counterflow heat exchanger with core and plenums at both ends

Here, this paper illustrates the morphing of flow architecture toward greater performance in a counterflow heat exchanger. The architecture consists of two plenums with a core of counterflow channels between them. Each stream enters one plenum and then flows in a channel that travels the core and crosses the second plenum. The volume of the heat exchanger is fixed while the volume fraction occupied by each plenum is variable. Performance is driven by two objectives, simultaneously: low flow resistance and low thermal resistance. The analytical and numerical results show that the overall flow resistance is the lowest when the core is absent, and each plenum occupies half of the available volume and is oriented in counterflow with the other plenum. In this configuration, the thermal resistance also reaches its lowest value. These conclusions hold for fully developed laminar flow and turbulent flow through the core. The curve for effectiveness vs number of heat transfer units (N tu ) is steeper (when N tu < 1) than the classical curves for counterflow and crossflow.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Pressure drop and heat transfer characteristics of nitrate salt and supercritical CO 2 in a diffusion-bonded heat exchanger

A lab-scale 316/L stainless steel diffusion-bonded heat exchanger was examined within a coupled high-temperature test facility consisting of an atmospheric-pressure nitrate salt loop and a supercritical carbon dioxide (sCO 2 ) loop operating between 10 and 16 MPa. Pressure loss measurements collected for flow rates up to 0.55 kg/s of Solar Salt and up to 0.6 kg/s of carbon dioxide were used to generate friction factor correlations for the respective circular and semicircular zig-zag flow passages. Heat transfer measurements were also performed over a wide range of conditions to produce Nusselt correlations for the CO 2 and nitrate salt geometries. The Nusselt number is deduced from a heat transfer resistance network and overall conductance measurements collected across the operating envelope of the coupled sCO 2 – nitrate salt test facility. The CO 2 side correlation showed excellent agreement with existing correlations in the literature. Further, the salt side, having nearly circular channels with a different zig-zag angle and hydraulic diameter, yielded a new correlation applicable to the laminar flow regime. To examine the similitude of the friction correlations, pressure drop testing with water was performed on both sides of the component as well. Finally, results from non-destructive examination are discussed to provide insights regarding inspection methods and draining performance of high-temperature liquids in compact heat exchangers.

36 MATERIALS SCIENCE↗

Comparison of Shape Optimization Methods for Heat Exchanger Fins Using Computational Fluid Dynamics

Inverse design techniques are one way to leverage advances in 3D printing, artificial intelligence, and computational resources to achieve increased performance of heat exchangers. Two optimization techniques (genetic algorithm and particle swarm) and three geometry representations (binary level set, composite Bézier, and free form deformation) are used to increase the heat transfer and reduce the pressure drop of a heat exchanger fin. After running 210,810 OpenFOAM simulations, results indicate that a significant performance increase of the fin can be realized in less than 48 hrs, allowing for such a process to be integrated in traditional design processes. The best design increased the performance of the objective function, compared to the baseline rectangular geometry by 75%. A custom distributed infrastructure was built, allowing for all methods to reach 95% of the final objective values in a little over 4 hrs, handling 1674 OpenFoam simulations per hour.

42 ENGINEERING↗

Study on corrosion migrations within catalyst-coated membranes of proton exchange membrane electrolyzer cells

The corrosion of low-cost, easily manufactured metallic components inside the electrochemical environment of proton exchange membrane electrolyzer cells (PEMECs) has a significant effect on their performance and durability. Here, 316 stainless steel (SS) mesh was used as a model liquid/gas diffusion layer material to investigate the migration of corrosion products in the catalyst-coated membrane of a PEMEC. Iron and nickel cation particles were found distributed throughout the anode catalyst layer, proton exchange membrane, and cathode catalyst layer, as revealed by scanning transmission electron microscopy and energy dispersive X-ray spectroscopy. Our results indicate the corrosion products of 316 SS are transported from anode to cathode through the nanochannels of the Nafion membrane, resulting in impeded proton transport and overall PEMEC performance loss.

08 HYDROGEN↗

Next-generation anion exchange membrane water electrolyzers operating for commercially relevant lifetimes

Alkaline anion exchange membrane (AEM) water electrolysis has gained increasing attention due to its potential to achieve low-cost, high performance hydrogen production. However, most existing membranes are not durable in industrial settings. In this work, we demonstrate good performance relative to industrial parameters using Sustainion® anion exchange membranes. Long-duration tests showed stable performance of 1 A/cm 2 at 1.85 V with a degradation rate of less than 1 μV/h over 10,000 h. The projected lifetime is thus over 20 years. Daily on/off cycling performance over the course of 30 years was simulated experimentally through accelerated voltage shock tests, resulting in a performance loss of only 0.15 μV/cycle over 11,000 cycles. As shown through impact and crossover testing, an improvement in performance is achieved by the addition of zirconia to the polymer matrix and mechanically reinforcing the membrane.

08 HYDROGEN↗

Coexistence of positive and negative exchange bias effect in Pr-doped NdCrO 3 samples

Positive and negative exchange bias effects are observed in Nd 1-x Pr x CrO 3 (0.00 ≤ x ≤ 1.00) polycrystalline samples. The shift of hysteresis loops, either opposing or following the direction of the field cooling, depends on the concentration of praseodymium. The temperature dependence of magnetization reveals a magnetic transition at T ≈ 220 K likely ascribed to the N é el temperature of Cr 3+ magnetic moments. The non-Kramer Pr 3+ ion seems to play an important role in the magnetic properties of this compound. In the range 0.00 ≤ x ≤ 0.60, all samples presented a decrease in the magnetization below TN and a clear compensation point. Pr-rich samples (x ≥ 0.70) show a paramagnetic-like behavior down to low temperatures. We report the most impressive result is the relation between reversal magnetization and the signal of exchange bias effect which seems be tuned by the Pr-doping.

36 MATERIALS SCIENCE↗

B-DeepONet: An enhanced Bayesian DeepONet for solving noisy parametric PDEs using accelerated replica exchange SGLD

Here, the Deep Operator Network (DeepONet) is a neural network architecture used to approximate operators, including the solution operator of parametric PDEs. DeepONets have shown remarkable approximation ability. However, the performance of DeepONets deteriorates when the training data is polluted with noise, a scenario that occurs in practice. To handle noisy data, we propose a Bayesian DeepONet based on replica exchange Langevin diffusion (reLD). Replica exchange uses two particles. The first particle trains a DeepONet to exploit the loss landscape and make predictions. The other particle trains a different DeepONet to explore the loss landscape and escape local minima via swapping. Compared to DeepONets trained with state-of-the-art gradient-based algorithms (e.g., Adam), the proposed Bayesian DeepONet greatly improves the training convergence for noisy scenarios and accurately estimates the uncertainty. To further reduce the high computational cost of the reLD training of DeepONets, we propose (1) an accelerated training framework that exploits the DeepONet's architecture to reduce its computational cost up to 25% without compromising performance and (2) a transfer learning strategy that accelerates training DeepONets for PDEs with different parameter values. Finally, we illustrate the effectiveness of the proposed Bayesian DeepONet using four parametric PDE problems.

97 MATHEMATICS AND COMPUTING↗