Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Cost-effective Manufacturing and Morphological Stabilization of Nanostructured Cathodes for Commercial Solid Oxide Fuel Cells (SOFCs) [Slides]

The overall goals of the program were to develop methods for preparing and stabilizing SOFC electrodes by infiltration that can be manufactured on a practical scale, then transfer those methods to cells in stacks. Cathodes prepared by infiltration of nanoparticles into a porous scaffold of the electrolyte have demonstrated outstanding electrochemical performance and mechanical strength but are difficult to manufacture due to the large number of infiltration steps required to produce a conductive composite and show poor stability due to sintering of the nanoparticles. At Penn, the main goal was to develop a fabrication method that uses only a small number of infiltration steps. Infiltration with molten salts and electrodeposition were pursued but deemed impractical. A method in which an electronically conductive scaffold consisted of a composite of a mixed conductor, LSF (La 0.9 Sr 0.1 FeO 3 ), with yttria-stabilized zirconia (YSZ) was found to be promising. While some cation mixing between LSF and YSZ was observed during calcination, there was no evidence for new phases in XRD and incorporation of Zr into the perovskite could be minimized by reducing the Sr content of the LSF. To stabilize nanoparticles infiltrated into the LSF-YSZ composite scaffold, the USC team examined the effects of Atomic Layer Deposition with ZrO 2 and infiltrated nanoparticles. Significantly enhanced stability was observed with the infiltrated nanoparticles. The FuelCell Energy team prepared 4”x4” cells in which an LSF-YSZ composite scaffold was cofired with the YSZ electrolyte and infiltrated with LSCF nanoparticles. Apparently because the LSF-YSZ scaffold layer was very thin in this case, the cation mixing that occurred during calcination resulted in a poor scaffold-electrolyte interface which caused reduced performance.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

A System Engineering Approach in the Analysis of Ionic Liquids Properties [Thesis]

Room temperature ionic liquids (RTIL) are ionic compounds, comprised of a cation and anion, in the liquid state at temperatures below 100 ⁰C. There are estimated 10 18 anion and cation combinations, which can create RTILs with unique properties. While the ionic character of RTILs made them attractive in a wide variety of electrochemical applications, their behaviors under electrochemical conditions are not well understood. In this research, we developed a RTIL testbed to investigate how RTILs differ from molecular solvents and electrolytes in electrochemical systems through the study of the effects of their morphology and chemical properties on the electron transfer processes. The test bed is composed of three modules: Electrochemistry, Material characterization, Computational. All modules have been completely developed, verified, and integrated and two of them, i.e., Electrochemistry and Material characterization have been validated in this dissertation. To evaluate the proposed system, experiments were performed on solutions of a redox active species in RTILs. It was found that it is possible to investigate the RTIL's morphology and chemical properties' impact on the electron transfer processes of the solute based on the outcomes and evaluations of tests performed by the RTIL testbed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Core-Shell Heterostructures as Functional Materials for Solid Oxide Fuel Cell (SOFC) Electrodes

The principal objective of this project was to synthesize core-shell heterostructures for solid oxide fuel cell cathodes using a molten salt solvent. In doing so, the main goals were split into a) to elucidate and understand the influence of molten salt chemistries to expeditiously synthesize perovskite type oxides for solid oxide fuel cells, b) provide a chemical framework for future molten salt syntheses of energy relevant ceramic materials, c) demonstrate and investigate the required parameters for the optimal core-shell synthesis and yield of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) – La 0.8 Sr 0.2 MnO 3 (shell), and d) demonstrate improved cathode performance of core-shell LSCF-LSM compared to an LSCF cathode on symmetric cells. The results clearly show that a) the influence of the molten salt cation outweighs the anion in regards to product stoichiometry, b) molten salts should be tailored to balance cationic and anionic acidity for high product yield, c) high yield of core-shell nanoparticles can be achieved by optimal mass ratio between core to shell, dwell time in the salt, size ratio between core to shell, and mass ratio between overall powder to salt, and d) the core-shell LSCF-LSM cathodes have lower polarization resistances than LSCF at higher temperatures. More work is required to optimize core-shell cathode performance at lower temperatures. However, this work thus provided justification for using the molten salt synthesis for SOFC cathodes and provided insights into future material modifications for improved performance.

08 HYDROGEN↗
DOE OSTI2022

Reduced diffusion and enhanced retention of multiple radionuclides from pore structure characterization of barrier materials for enhanced repository performance

Fluid flow and chemical transport in porous media are the macroscopic consequences of pore structure, which integrates geometry (e.g., pore size and surface area, pore-size distribution) and topology (e.g., pore connectivity). Low-permeability geological media whose pores are poorly interconnected will exhibit the characteristics of anomalous diffusion and sample size-dependent effective porosity, which will strongly impact long-term net diffusion and retention of radionuclides in geological repository settings involving different host rocks and barrier materials. A suite of innovative and complementary experimental approaches is utilized to study the microscopic pore structure and macroscopic fluid flow & chemical transport for a range of host rocks and barrier materials, in addition to standard clay minerals and reference rocks. With a particular focus on quantifying the presence and magnitude of “isolated” pores for a reduced effective porosity in low-permeability geomedia, the integrated methodologies for basic properties and pore structure characterization of these geomedia include X-ray diffraction, thin section petrography, grain size distribution, water immersion porosimetry after vacuum-pulling for full saturation, mercury intrusion porosimetry, nitrogen physisorption, scanning electron microscopy, X-ray computed tomography, and (ultra-)small angle neutron (X-ray) scattering. In addition, custom-designed gas diffusion, tracer recipe involving a range of anionic and cationic chemicals with subsequent analyses by laser ablation and inductively coupled plasma-mass spectrometry, along with batch sorption, column transport, and imbibition tests were conducted for coupled effects of pore structure and chemical retention/transport. From the perspectives of pore structure in conjunction with multiple and complementary approaches to examining a range of sample sizes under different observational scales, we find that the poor pore connectivity is prevalent in low-permeability media (mudstone and crystalline rock) that is related to geological processes (e.g., compaction, diagenesis and thermal maturation). For example, the deep and organic matter-rich mudstones have a much smaller effective porosity than the total porosity (as a result of poor pore connectivity) and associated diffusion coefficient, and the effective porosity & diffusion coefficients are also dependent upon the sample sizes used in the measurement. Similarly, most of the pore space in the shallow mudstone is also controlled by pore-throat diameters in the 5-50 nm range of intergranular pore types from its fine-grained nature, but with an overall good pore connectivity. However, the nm-sized pore space (physically pore-network architecture) and strong sorption capacities (chemical retention from clay minerals) of both shallow and deep mudstones lead to the synergistic retention of cationic radionuclides and their utilities as effective host rocks and barrier materials. Our unique approaches of studying how the micro-scale pore structure affect macro-scale fluid flow, diffusion & retention, and chemical transport produce improved mechanistic understanding, and realistic quantification, of diffusion and retention of typical radionuclides in a range of generic host rocks and barrier materials (clay/shale, salt, crystalline rock, and tuff), with the overall results leading to scientifically-based understanding of enhanced isolation (from both diffusion and retention) of radionuclides and improved confidence on the long-term performance of geological repository to store high-level radioactive wastes. In addition to the training of 25 undergraduates, graduates, and postdocs of UTA, the scientists (organizations) involved in performing this work (e.g., discussion, sample sharing, and operation of SANS and SAXS instruments) include Ed Matteo, Yifeng Wang, and Kristopher Kuhlman (Sandia National Laboratories), Jens Birkholzer, Liange Zheng, Tim Kneafsey, and Sharon Borglin (Lawrence Berkeley National Laboratory), Mavrik Zavarin (Lawrence Livermore National Laboratory), Yukio Tachi and Yuta Fukatsu (Japan Atomic Energy Agency), Mieke de Craen (Euridice, Belgium), Markus Bleuel (NIST), Wei-Ren Chen, Gergely Nagy, Changwoo Do, William Heller, Larry Anovitz, and Kenneth Littrell (ORNL), as well as Jan Illvsky, Ivan Kuzmenko, Ju-Sang Park and Jon Almers (ANL). Key deliverables include a total of 13 peer-reviewed journal articles (nine published and three under review), 23 presentations at scientific conferences (AAPG, AAPG Southwest Section, AGU, Asian Clay Conference, GSA, GSA South-Central Section, IHLRWM, InterPore, International Conference on Chemistry and Migration Behavior of Actinides and Fission Products in the Geosphere, International Conference on Coupled Processes in Fractured Geological Media: Observation, Modeling and Application), and academic institutions (UTA, New Mexico State University; University of Poitiers, France; University of Helsinki, Finland; Uppsala University, Sweden; Istanbul Technical University, Turkey) and other organizations (Andra, France; Posiva Oy, Finland).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Passivated Interfaces and Surface Recombination Velocities in Halide Perovskites

Surfaces and charge-extracting contacts remain major sources of non-radiative recombination loss; limiting the performance of perovskite PV compared to theoretical limits. We investigate mixed-cation mixed-halide perovskites and demonstrate that, with chemical surface passivation, they can achieve >4 μs minority carrier lifetimes, and >20% external PL quantum yields (PLQY), and nearly single-exponential decay kinetics. This high PLQY observed corresponds to ~97% of the Shockley-Queisser theoretical quasi-fermi level splitting, a first for MA-free mixed-cation mixed-halide compositions. The high PLQY and long PL lifetimes allow us to measure average surface recombination velocities (SRV) <10cm/s, with a champion low of ~1cm/s (a conservative estimate). We show how such improvements in SRV should lead to an absolute improvement in PCE of >4% even with the best of contact alignments. We investigate different MA-free high bandgap compositions, including bandgaps relevant for tandem applications (1.7-1.8eV), and demonstrate performance improvements across all these compositions with our surface passivation strategy. Lastly, using a combination of surface characterization techniques, we show Lewis base interactions of the passivating agent with the perovskite surfaces.

passivation↗
DOE OSTI2023

Rare earth separation in voltage-gated 2D MXene membranes

The separation of rare earth elements (REEs) has historically been a complicated and expensive process, producing significant amounts of pollution. To this end, MXene membranes (MXMs) have attracted researchers' interest. It has been demonstrated that MXMs are capable of separating ions and that it is possible to precisely control the separation rate by applying a voltage to the membrane. Indeed, due to their chemical nature, MXenes show outstanding electrical conductivity. However, the effect of applied voltage on the permeation rate and separation effects of iconic species remains an intriguing area of research. In this work, we demonstrate how applying different voltages (gate voltage) to a MXM affects the permeation rate of various REE ions. Our hypothesis to explain MXMs behavior towards REE is that under negative voltage, the interlayer spacing decreases due to attraction between charged MXene surfaces and intercalated cations, increasing the separation factor between REEs. Under positive voltage, the interlayer spacing increases due to repulsion between the MXene surfaces and intercalated cations. However, we demonstrate relatively poor separation capability for REEs at 1mM starting concentration and 1.0 V applied DC voltage (separation factor ~1-3). This study demonstrates the need for future experiments to observe varied experimental conditions and chemical functionalization to determine whether MXene membranes can be an efficient platform for REE separation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

First Principles Modeling of Tritium Trapping in γ-LiAlO 2 Nanovoids

Experimental STEM and APT investigations both indicate the presence of nanovoids in γ-LiAlO 2 pellets. While those nanovoids can affect the diffusion of tritium in pellets, first principles simulations have been conducted to evaluate the potential for tritium trapping by single and double cation and anion vacancies. It was found that tritium trapping allows to recover a significant amount of the formation energy cost of cation vacancy, while the trapping of tritium by anion vacancies further increase the energy cost of forming a vacancy. The simulations also indicated the potential for tritium to be trapped in various forms by forming bonds such as Al—T, O—T or T 2 . These results raise further questions regarding the speciation and dynamics of tritium trapped in nanovoids.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Synthesis of PbS/CdS/Cu 2-x S core/shell/shell quantum dots for rapid NIR emission.

Nanoscale semiconductors, known as quantum dots (QDs), possess unique size-tunable optical and electrical properties. With continued research into quantum information storage and quantum communication, the need for near-infrared single photon emitters and absorbers has gained prominence. Lead sulfide QDs have only recently been explored as a reliable near-infrared single photon emitters with the addition of a protective cadmium sulfide shell. Despite the increased air and room temperature stability of these QDs, long photon emission times have limited widespread application. This work examines the enhanced photon emission due to the Purcell effect provided by the layering of copper sulfide. In particle, this work synthesized lead sulfide cores in the 10 nm range, successfully layered cadmium sulfide through cation exchange, and attempted the cation exchange of copper sulfide, as identified with near-infrared absorbance spectra, transmission electron microscopy, and photoluminescence spectra.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of Contaminants and Mobility in WMA A-AX Boreholes D0006 and D0008

This study was initiated to determine if subsurface contaminants in the A-AX vadose zone at the Hanford site (boreholes D0006 and D0008) caused corrosion of nearby stainless steel well casings (299-E-24-19, 299-E25-46, and 299-E25-236) and, based on the type and distribution of contaminants, determine if contaminants are from one or more sources including a) the A-104 and/or A-105 tanks, b) the 242A evaporator, and c) the 200-E-286 ditch. A tiered approach was used for characterizing contaminants in vadose zone sediments starting with mobile and total contaminant concentrations (Tier 1), characterizing contaminant speciation (Tier 2), and measuring contaminant leaching (Tier 3). Total and mobile contaminant measurements at seven depths showed elevated sulfate and nitrate in all samples (130 to 280 ft depth), elevated chloride in five depths, and no elevated radionuclides except I-129 in D0006 at 206 to 208 ft depth. If these contaminants were initially acidic, stainless-steel corrosion would occur. However, because sediments likely have a high acid neutralization capacity, an acidic spill would have been neutralized within tens of feet, so casing corrosion would likely occur in shallow sediments. GEL labs data also shows low (but above natural) chromate from shallow to 170 ft depth, then higher chromate to 280 ft, suggesting a surface Cr spill or casing corrosion. GEL labs data also showed evidence of more than one plume, with deep nitrate, sulfate, and chloride migration, but only shallow tritium migration. Tritium should migrate nearly unretarded in the subsurface like nitrate and chloride. Elevated aqueous cations and anions in the D0006 206 to 208' depth pore water (SO 4 2- , NO 3 - , Na + , K + , Ca 2+ , Mg 2+ , Si) could be the result of acid disposal and calcite dissolution at shallow depth, with deeper migration of SO 4 2- , NO 3 - from acids and Ca 2+ and Mg 2+ from calcite. Elevated Si (160 mg/L) indicates dissolution of clays or other silicates, which can also occur in acids. Acid extractable metals did show elevated Cr (but not Fe, Ni, Mo, and Mn) above natural levels, which may indicate stainless-steel well corrosion or transport of metals from a shallow spill. The elevated I-129 in D0006 at 206 to 208' depth was low with 0.34 μg/g in pore water and 1.5 μg/g total extractable I-129 in the sediment, which indicates significant fraction of I-129 was bound in one or more precipitates. Although total I-129 was below detection limits in most extractions due to high molybdate interference, I-127 analysis provided some insight into potential precipitate phases. Total I-127 was mainly extracted by acetate or acetic acid (67%), which may be iodine in calcite. Inorganic carbon measurement identified 1.65% calcite, and total organic carbon (TOC) was below detection limits, so iodine was not associated with organic matter. Nearly all the I-127 was present as iodide. In 1-D leach experiments, I-127 as iodide leached from the sediment within 2 pore volumes. Due to high and dynamic molybdate leaching from the sediment and interference with I-129 analysis, there were few quantifiable I-129 measurements. The calculated molybdate release rates from the sediment suggested Mo was being released from the same precipitate phase, such as molybdate incorporated into calcite. Overall, because there was little radioactive contamination measured in D0006 and D0008 boreholes, potential releases from A-104 and A-105 did not reach this location south of the A tank farm. Elevated cations and anions found in D0006 and D0008 at depth as the result of acidic disposal could cause shallow stainless steel casing corrosion. The nearby 242A evaporator generally contained alkaline waste and tritium, but the nearby 200-E-286 ditch generally contained high Cl - liquid effluent, so these are unlikely to be acidic sources.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Review of Mercury Sequestration in Cementitious Waste Forms

Decontaminated salt solution from Tank 50 at the Savannah River Site (SRS) is known to contain dissolved mercury species which are present as hydroxides and oxides. These species are reported in analytical measurements as the organic cation [CH 3 Hg] + and the inorganic cation Hg 2+ . The salt solution is mixed with cementitious reagents, blast-furnace slag (BFS) and thermally beneficiated Class F fly ash in the Saltstone Processing Facility and pumped into engineered Saltstone Disposal Units, (SDUs), to produce a solidified waste form. The solidified waste form, saltstone, encapsulates and chemically stabilizes the mercury and other contaminants, sequestering them from release into the environment. With the discovery of methylmercury in the salt solution, testing was performed to determine the extent to which saltstone prepared with methylmercury (MeHg) retains mercury in the Toxicity Characteristic Leaching Procedure (TCLP). Results from this testing indicated that the amount of mercury extracted remained below the regulatory limit, and that the saltstone formulation with a greater proportion of BFS performed slightly better at retaining Hg in the solid.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Enabling in-situ LIBS measurements of liquids and slurries

The aim of this work was to explore the use of, and further develop, a in-situ and near-real time LIBS (Laser Induced Breakdown Spectroscopy) instrument to measure liquids relevant to the Hanford site. Specifically, we investigated the feasibility of using LIBS to measure the cation composition of HLW (High Level Waste) streams. In addition, we focused on enabling continuous interrogation of those liquids using the LIBS system. For the first part, we investigated simple (sodium nitrate) solutions as well as various Hanford tank waste surrogate slurries. We showed that relevant cations (such as sodium, aluminum, magnesium, potassium) can be measured via LIBS under good conditions but the results – both quantitative and qualitative (aka reproducibility) – strongly depend on the kind and concentration of the material used. The dependence of signal intensity on concentration was also confirmed by other measurements conducted (sodium chloride and sodium nitrate in water). For the second part, we investigated the influence of varying depth and concentration of a liquid sample. We observed that for the concentrations and fill depths investigated, the liquid fill depth did not impact the emission intensity of the analyte, while concentration is confirmed to have significant effects. The results of the sample depth experiments influenced testing of waste surrogates. In addition, we focused on further developing and adapting data fitting tools in order to efficiently, accurately, and reproducibly identify the elements and materials present in a LIBS spectrum.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Reinforced AEM Separators Based on Triblock Copolymers for Electrode-decoupled RFBs

Washington University in St. Louis (WUSTL), in collaboration with The University of Texas at San Antonio (UTSA) and Giner Inc. developed highly selective anion exchange membranes (AEMs) and a novel electrode-decoupled redox flow battery (RFB) for grid scale energy storage as part of the ARPA-E IONICS program (with connections to the DAYS program in the later part of the project). RFBs exhibit the crucial characteristic of system-level decoupled scaling of energy and power which makes them cost effective for the multi-GWh scales envisioned for grid-scale energy storage solutions. This has led to extensive (and deserved) research interest and attention. This project aimed to enhance the design space available for redox-flow batteries (RFBs) by enabling the long-term separation of disparate cationic (elemental) actives using a highly selective membrane separator, while concurrently permitting the transport of anions to balance charge. The approach proposed was to design and develop a highly selective anion-exchange membrane (AEM), which would in turn permit the design and development of electrode-decoupled RFBs. Pairs of (different element) cationic species with redox reactions exhibiting a large difference in their standard electrode potentials were identified to develop high voltage, high power RFBs while disrupting the existing paradigm of using a single element which can ionize to more than two soluble oxidation states (e.g.: Vanadium).

25 ENERGY STORAGE↗
DOE OSTI2025

Small-scale Assessment of Simplified Ceramic Waste Form Processing

The feasibility of directly processing glass-bonded sodalite ceramic waste form materials by heating a mixture of Zeolite 4A, chloride salt, and sodium borosilicate binder glass was demonstrated by generating laboratory-scale materials. This direct processing method eliminates pre-setting the moisture content of the Zeolite 4A, eliminates the step of occluding salt in the prepared Zeolite 4A prior to processing, and can be conducted using larger particle sizes of crushed Zeolite 4A and crushed borosilicate glass than those called for in the current method. These simplifications are expected to facilitate material transfer and handling in a hot cell or controlled atmosphere environment and be more readily implemented at large scale than the current method. Most materials made to assess these simplifications were directly processed at 925 °C for two hours in an argon atmosphere glovebox, but one material was processed at 925 °C for four hours and one material was processed at 880 °C for two hours. Sodalite was generated and became microencapsulated by the binder glass in all materials. The microstructures were uniform throughout each product, were similar in all products, and were similar to the microstructures of materials made previously using the pressureless consolidation or hot isostatic pressing methods. Various formulations showed the efficiency of sodalite generation was not sensitive to the salt-to-Zeolite 4A ratio or salt-to-glass mass ratio, although a greater relative mass of glass is required to encapsulate sodalite generated from large particles of aggregated Zeolite 4A. The upper limit of salt loadings that can be effectively processed remains to be determined. The effectiveness of direct processing provided new insights into the conversion mechanism. The salt was likely dissolved into the glass that transported NaCl into the Zeolite 4A aggregates and sodalite was generated in situ as NaCl migrated from the outside of the aggregate inward. Other salt cations (e.g., potassium, strontium, cesium, and probably lithium) remain dissolved in the glass encapsulating the zeolite/sodalite domains. When the glass solidifies during cooling, small halite inclusion phases form in glass within sodalite domains and large mixed salt inclusions form in glass surrounding the sodalite due to the low solubility of chloride in the (solid) glass. Other salt cations were oxidized during processing and formed inclusions in the bulk glass (e.g., neodymium). Initial degradation tests show the dissolution behavior of directly processed CWF (SCWF) materials is similar to CWF materials made using different methods.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Molecular Scale Tuning of Covalent Organic Frameworks for Enhanced Properties

Covalent organic frameworks (COFs) are a type of porous, extended structure material which has demonstrated utility in numerous applications, including sensing and separations. Judicious choice of the linker and node not only fine tune the size of the framework, but also the functionality. We seek to tailor COF materials for applications in gas capture and electrochemical sensing. Herein, we demonstrate the material properties of COFs can be fine-tuned via post-synthetic metal cation doping of the parent structures. We have synthesized several COF structures with varying linkers which allow for the incorporation of metal cations. Structures incorporating Zn 2+ , Mn 2+ , and Cu 2+ have demonstrated utility in improving the CO 2 uptake properties of the COFs, while Ag + doped structures show potential as electrochemical sensors for chloride anions.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Bipolar Membranes Electrodialysis for Water Purification and Resource Recovery

Reverse osmosis concentrate (ROC) from inland brackish water desalination and wastewater recycling presents moderate salinity, posing significant challenges for treatment and disposal. Existing treatment technologies predominantly rely on energy-intensive thermal methods, large-area evaporation strategies, or deep-well disposal, which often result in the loss of water value. Electrified membrane brine treatment offers a promising alternative by utilizing renewable energy sources, enabling complete water recycling. This work proposes the development of next-generation bipolar membrane electrodialysis (BMED) systems capable of desalinating brine while simultaneously recovering valuable resources. However, several critical challenges remain in the areas of membrane engineering for BMED. These include: 1) decreased current efficiency during desalination due to the low conductivity of feed chambers, 2) fouling and scaling from multivalent ions and contaminants in the feed, and 3) the retention and carryover of ROC contaminants, including PFAS compounds. Our research focuses on the development of novel anion exchange membranes (AEMs) and cation exchange membranes (CEMs) based on synthesized multiblock copolymers. We investigate the effects of block length, ion exchange capacity (IEC), and polymer backbone structure on cation and anion transport (e.g., Na+, Cl-, OH-, H+) for both our synthesized membranes and commercial membranes. Fundamental properties of these membranes, such as water uptake, IEC, and ionic conductivity, are also evaluated to optimize performance for BMED applications.

08 HYDROGEN↗
DOE OSTI2026

Harvesting Isotopically Pure Ac-225 from Ra-225 Produced in Thorium Target Spallation Reaction

A method for isolating Ra-225 from linear accelerator irradiated Th metal chemical processing waste streams has been established. Separating Ra-225 from the complex matrix following proton irradiation of Th metal provides a source of isotopically pure Ac-225 free of the Ac-227 impurity that is present in accelerator-produced Ac-225. Ra isotopes are first separated from the irradiated Th target via cation exchange methods. Importantly, the Ra-containing fraction is cleaned from residual citrate via dilute nitric acid washes (0.5 M) on AG50W-X8 resin. The mixed Ra isotopes are then further purified from Ba-140 impurity using a Sr resin column. Ra elutes through the resin with successive washes of 2.5 M HNO 3 while Ba-140 is retained. Ac-225 is then harvested by loading the Ra content onto an AG50W-X8 cation exchange column where the Ra-225 parent is eluted with 2.5 M HNO 3 before the Ac-225 daughter is eluted with 8 M HNO 3 .

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2020

Implementation of Ion Exchange Processes for Carbon Dioxide Mineralization Using Industrial Waste Streams

Sequestration of CO 2 within stable mineral carbonates (e.g., CaCO 3 ) represents an attractive emission reduction strategy because it offers a leakage-free alternative to geological storage of CO 2 in an environmentally benign form. However, the pH of aqueous streams equilibrated with gaseous streams containing CO 2 (pH < 4) are typically lower than that which is required for carbonate precipitation (pH > 8). Traditionally, alkalinity is provided by a stoichiometric reagent (e.g., NaOH) which renders these processes environmentally hazardous and economically unfeasible. This work investigates the use of regenerable ion-exchange materials to induce alkalinity in CO 2 -saturated aqueous solutions such that the pH shift required for mineralization occurs without the need for stoichiometric reagents. Na + -H + exchange isotherms (at [H + ] = 10 −8 –10 −1 M) and rates were measured for 13X and 4A zeolites and TP-207 and TP-260 organic exchange resins in batch equilibrium and fixed-bed exchange experiments, respectively. At solutions equilibrated with CO 2 at 1.0 atm (pH = 3.9), H + exchange capacities for the materials were similar (1.7–2.4 mmol H + /g material) and resulted in pH increases from 3.9 to greater than 8.0. Multi-component mixtures using Ca 2+ and Mg 2+ cations (at 10 −3 –10 −1 M) in CO 2 -saturated water were used to probe competitive ion exchange. The presence of divalent cations in solution inhibited H + exchange, reducing capacities to as low as 0.2 mmol H + /g for both resins and zeolites. Dynamic H + exchange capacities in fixed-bed ion exchange columns were similar to equilibrium values for resins (∼1.5 mmol/g) and zeolites (∼0.8 mmol/g) using inlet solutions that were equilibrated with gaseous streams of CO 2 at 1.0 atm. However, exchange kinetics were limited by intraparticle diffusion as indicated by the increased rate parameters with increasing inlet flow rates (20–160 cm 3 min −1 ). Experimental calcite precipitation from mixing the alkaline CO 3 2− -rich water solution obtained from the ion-exchange column with a simulated liquid waste stream solution achieved thermodynamic maximum yields. The results from these studies indicate that ion exchange processes can be used as an alternative to the addition of stoichiometric bases to induce alkalinity for the precipitation of CaCO 3 , thereby opening a pathway toward sustainable and economic mineralization processes.

42 ENGINEERING↗
DOE OSTI2022

Short- to Intermediate-Range Structure, Transport, and Thermophysical Properties of LiF–NaF–ZrF4 Molten Salts

LiF–NaF–ZrF 4 multicomponent molten salts are identified as promising candidates for coolant salts in molten salt reactors and advanced high-temperature reactors. This study focused on low-melting point salt compositions of interest: 38LiF–51NaF–11ZrF 4 , 42LiF–29NaF–29ZrF 4 , and 26LiF–37NaF–37ZrF 4 . Ab-initio molecular dynamics (AIMD) calculations were performed and compared with available experimental data to assess the ability of rigid ion models (RIM) to reproduce short- to intermediate-range structure, transport, and thermophysical properties of the LiF–NaF–ZrF 4 salt mixtures. It is found that as ZrF 4 mol% increases, the average cation–anion coordination number (CN) of monovalent cations (Li + , Na + ) obtained from RIM calculations decreases, while multivalent Zr 4+ CN varied from 15% to 19% in comparison to corresponding AIMD values. In addition, RIM is found to predict the existence of 7, 8, and 9 coordinated fluorozirconate complexes, while AIMD and the available experimental data showed an occurrence of 6, 7, and 8 coordinated complexes in the melt. The intermediate-range structure analysis revealed that while the RIM parameters are able to reproduce a local structure for lower ZrF 4 mol% salts such as in 38LiF–51NaF–11ZrF 4 , an extensive fluorozirconate network formation is observed in RIM simulations for higher ZrF 4 mol% compositions. The network generated by RIM parameters is found to be mainly connected by “corner-sharing” fluorozirconate complexes as opposed to both “edge-sharing” and “corner-sharing” connectively portrayed by AIMD. It is found that a close agreement between AIMD and the RIM salt structure for the 11-mol% ZrF 4 salt resulted in good agreement in the calculated Zr diffusivities and the viscosity values. However, due to the inaccurate short- to intermediate-range structure prediction by RIM for higher ZrF 4 mol% compositions, thermophysical properties such as densities and heat capacity differ by up to 26% and 27%, respectively, upon comparison with AIMD and experimental values. Also, the network-dominated properties such as diffusion coefficients and viscosities differed by up to two and three orders of magnitude, respectively. This study signifies the importance of accurate salt structure generation for an accurate prediction of transport and thermophysical properties of multicomponent molten salts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗