Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Assembly”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,783 records · Page 99
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Design fabrication and nondestructive testing of six experimental AGCarb/Intermold 3 cylinder assemblies

Six subscale Intermold cylinder assemblies with a total of twelve different concepts for transition to AGCarb were fabricated. Three of the cylinder assemblies were made by helically winding the hoop fibers and three were of orthogonal configuration. The fabrication process is summarized and details of each manufacturing method are given. The objectives of the test program were to: (1) demonstrate the fabricability of the Intermold 3 subscale flanges, (2) produce an integral transition from Intermold 3 to AGCarb material, (3) define a workable manufacturing process, and (4) identify a best suited inspection method. The objectives were met and the results are described.

Thacher, E. F.↗
NASA NTRS1972

Identification of rotating assembly inertial and bearing parameters.

The problem of estimating the state of a turbopump rotating assembly and identifying unknown products of inertia and unknown bearing parameters is considered. A linearized, extended Kalman filtering approach has been used and found to be successful for both state estimation and parameter identification in an inherently nonlinear problem. The input data were simulated Bently test data obtained from a verified 12-dimensional state-space model and were compared with real Bently test data obtained from NASA. The results prove the feasibility of using this model and this type of test data to obtain the hidden parameters of a typical turbopump rotating assembly.

Alspach, D. L.↗
NASA NTRS1972

Mariner Venus/Mercury 1973 rocket engine assembly

The fabrication and test of rocket engine assemblies (REA) for Mariner Venus/Mercury 1973 are reported. The fabrication, assembly and flight acceptance test of seven REA's including the type approval test of one engine and fabrication of one additional kit consisting of detail parts for an engine ready for catalyst loading are presented. The MV/M '73 REA which is a nominal 51 lbs thrust monopropellant engine is described. Under steady state operation the specific impulse is not less than 228 lb-sec at 55 lb and 218.5 lb-sec at 10 lb thrust varying linearly between these limits. The characteristic velocity is not less than 4100 ft/sec at any thrust level.

Snoke, D. R.↗
NASA NTRS1973

Development of the elevation drive assembly for orbiting solar observatory I (EYE)

The requirements for pointing accuracy, friction, and power for the elevation drive assembly of an orbiting space observatory are discussed briefly. A description of the components making up the assembly is presented. Special features requiring development testing prior to unit fabrication are more fully described together with a review of the test programs conducted and results obtained.

Sharpe, W. F.↗
NASA NTRS1974

Test results from a breadboard cryogenic propellant condition assembly

Cryogenic auxiliary propulsion systems consist of five major subsystems: propellant tanks, propellant conditioning assemblies, accumulators, propellant distribution systems, and thrustors. The propellant conditioning assembly (PCA) converts low pressure liquid to high pressure gas for use by the thrustors, and is one of the most complex subsystems of the cryogenic propulsion system. The ability to achieve rapid starts and at the same time maintain system control are two critical areas of PCA operation. To investigate these critical areas of operation, a PCA of the general type required was designed, fabricated, and tested using existing hardware. Realistic start times were achieved and system control was maintained at all operating conditions.

Stinson, H. P., Jr.↗
NASA NTRS1973

Liquid rocket valve assemblies

The design and operating characteristics of valve assemblies used in liquid propellant rocket engines are discussed. The subjects considered are as follows: (1) valve selection parameters, (2) major design aspects, (3) design integration of valve subassemblies, and (4) assembly of components and functional tests. Information is provided on engine, stage, and spacecraft checkout procedures.

Source record↗
NASA NTRS1972

Ground-Commanded Television Assembly (GCTA)

The characteristics of the Ground-Commanded Television Assembly (GCTA) are discussed. The equipment was used to provide television coverage of lunar surface explorations during Apollo 15, 16, and 17 missions. The subjects include the following; (1) yoke/faceplate qualification data, (2) elevation drive improvement program, (3) Apollo 17 thermal data, (4) equipment status, and (5) drawing status. Illustrations of the components of the assembly are provided. Tables of data are developed to show the performance of the components.

Source record↗
NASA NTRS1974

High reliability sheathed, beryllia insulated, tungsten-rhenium alloy thermocouple assemblies; their fabrication and EMF stability

Tantalum sheathed, BeO insulated, W-3% Re/W-25% Re thermocouple assemblies were fabricated and their emf drift determined during 2059 hours of exposure at 2073 K in a gaseous helium environment. The sheathed thermocouple assemblies were constructed from aged thermoelements, specially heat-treated BeO insulators, and specially cleaned and etched tantalum sheaths. Their thermal emf drifts ranged from the equivalent of only -0.3 to -0.8 K drift per 1000 hours of exposure at 2073 K. No evidence of any gross chemical attack or degradation of the component materials was found. The emf drift and material behavior of some unsheathed, BeO insulated, W-3% Re/W-25% Re thermocouples at 2250 and 2400 K were also determined. Unsheathed thermocouples tested in an argon environment at 2250 K for 1100 hours and at 2400 K for 307 hours exhibited changes in thermal emf that typically ranged from the equivalent of a few degrees K to as much as +11 K. Post-test examinations of these thermocouples revealed some undesirable material degradation and interaction which included erosion of the BeO insulators and contamination of the thermoelements by tantalum from the tantalum blackbody enclosure in which the thermocouples were contained.

Burns, G. W.↗
NASA NTRS1975

Varactor diode assembly with low parasitic reactances

Development of varactor diode assembly overcomes parasitic reactances of conventional varactor packages. In specially constructed assembly very high idler-frequency to signal-frequency ratios are used to obtain low-noise operation over maximum bandwidth.

Dickens, L. E.↗
NASA NTRS1975

Modification, fabrication, testing and delivery of ITT model F4012 RP tube/coil assembly

Results of the improvement program for the ITT model F4012 RP image dissector tube and coil are presented. This program undertaken to improve the characteristics of this assembly to make it more accurate for the Large Space Telescope trackers' applications. Comparisons are given of the performance of the new components and the original design goals. Recommendations for further tests and/or design changes to further improve the F4012 tube/coil assembly performance are given.

Source record↗
NASA NTRS1977

Meta-assembler

Machine-independent cross-assembler program can produce object modules for variety of computers. Program is capable of being reconfigured by data set supplied at assembly time.

Hodges, B. C.↗
NASA NTRS1977

Blade retainer assembly

A retaining assembly is provided for locking radially extending blades in a rotor disc associated with a gas turbine engine. The assembly includes a pair of spaced apart lugs axially extending from one side of the disc to form an access gap for insertion of a blade tang into a dovetail slot in the rotor disc. A pair of axially aligned inwardly facing recesses are disposed in the lugs. A retaining member resides in the recesses and extends across the gap to preclude egress of the blade tang from the dovetail slot. The retaining member includes at least one axially extending protrusion adapted to radially overlap and abuttingly engage a radially inwardly facing abutment surface on the lugs.

Luebering, G. W.↗
NASA NTRS1977

Lightweight reflector assembly

An inexpensive, lightweight reflective assembly member having good optical quality and particularly adaptable to accommodating temperature variations without providing destructive thermal stresses and reflective slope errors is described. The reflective assembly consists of a thin sheet of glass with appropriate reflective coating and a cellular glass block substrate bonded together. The method of fabrication includes abrading the cellular substrate with an abrasive master die to form an appropriate concave surface. An adhesive is applied to the abraded surface and a lamina reflective surface is placed under a uniform pressure to conform the reflective surface onto the desired abraded surface of the substrate.

Argoud, M. J.↗
NASA NTRS1975

The assembly of large structures in space

Techniques developed for orbital assembly of the support structure for a 1000 meter diameter microwave power transmission system antenna are described. The operation is performed in two phases using the shuttle remote manipulator system in low earth orbit, and a mobile assembler in geosynchronous orbit.

Smith, G. W.↗
NASA NTRS1977

Stress analysis of pressure vessel assembly

A radome assembly capable of withstanding large hydrostatic pressures was designed with a sapphire hemisperical dome and a plastic housing. These two parts were connected with a stainless steel flange ring. A finite-element stress analysis of this assembly was accomplished and an experimental load test was performed to verify the predicted stresses.

Eppink, R. T.↗
NASA NTRS1978

Institutional environmental impact statement, Michoud Assembly Facility, New Orleans, Louisiana

A description and analysis of Michoud Assembly Facility as an operational base for both NASA and NASA-related programs and various government tenant-agencies and their contractors is given. Tenant-agencies are governmental agencies or governmental agency contractors which are not involved in a NASA program, but utilize office or manufacturing space at the Michoud Assembly Facility. The statements represent the full description of the likely environmental effects of the facility and are used in the process of making program and project decisions.

Source record↗
NASA NTRS1978

DSN portable zero delay assembly

Design and test data on portable zero delay assemblies are reported. These assemblies are field-use delay standards to periodically calibrate the block 4 translator ranging paths at each 64-m antenna Deep Space Station.

Serhal, E. J., Jr.↗