Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid electrolyte”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Solution Blowing Synthesis of Li-Conductive Ceramic Nanofibers

Solid state electrolytes (SSEs) offer great potential to enable high-performance and safe lithium (Li) batteries. However, the scale-up synthesis and processing of SSEs is a major challenge. In this work, three-dimensional networks of lithium lanthanum titanite (LLTO) nanofibers are produced through a scale-up technique based on solution blowing. Compared with the conventional electrospinning method, the solution blowing technique enables high-speed fabrication of SSEs (e.g., 15 times faster) with superior productivity and quality. Additionally, the room-temperature ionic conductivity of composite polymer electrolytes (CPEs) formed from solution-blown LLTO fibers is 70% higher than the ones formed from electrospun fibers (1.9 x 10 -4 vs 1.1 x 10 -4 S cm -1 for 10 wt % LLTO fibers). Furthermore, the cyclability of the CPEs made from solution-blown fibers in the symmetric Li cell is more than 2.5 times that of the CPEs made from electrospun fibers. These comparisons here show that solution-blown ion-conductive fibers hold great promise for applications in Li metal batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The effect of aspect ratio on the mechanical behavior of Li metal in solid-state cells

The Li metal anode is necessary for solid-state batteries to dramatically exceed the energy density of state-of-the-art conventional Li-ion batteries. To enable the Li metal anode, the mechanical properties of Li metal under compression in a commercially relevant cell configuration must be determined. This work examines the compression creep behavior of Li metal coupled with a relevant model solid-state electrolyte (Li 6.5 La 3 Ta 0.5 Zr 1.5 O 12 ) and current collector (Ni) as a function of applied stress (1–10 MPa) and Li foil thickness (100–700 μm). At 1 MPa applied stress, the strain rate of all Li foil thicknesses under compression was almost four orders of magnitude lower than what is predicted from tensile creep tests. Steady-state creep behavior was observed for Li foil ≥350 μm at 5 MPa and ≥250 μm at 10 MPa. Conversely, sustained creep deformation was not observed for 100 and 150 μm Li foils at any applied stress. It is suggested that friction at the Li/LLZO and Li/Ni interfaces leads to the formation of hydrostatic stress that controls Li deformation at low aspect ratios. Finally, these results have implications for battery pack stack pressure requirements, particularly relating to void formation during stripping and Li metal filament penetration during plating.

25 ENERGY STORAGE↗
DOE OSTI2025

Overcoming misconceptions in lithium metal polymer electrolyte batteries

Uncovering the truth of lithium polymer batteries. Lithium metal is the holy grail of anodes due to its 10-fold higher gravimetric capacity than graphite. All-solid-state lithium polymer electrolyte batteries are receiving significant attention due to their increased flexibility compared to inorganic solid-state electrolytes, which enhances processability, accommodates cell swelling, and enables more homogeneous interphases. However, prototype solid-state lithium polymer electrolyte batteries have been limited in their usage due to the low ionic conductivity of the electrolyte, which limits their ability to cycle lithium metal at high rates. In this opinion, we provide alternative interpretations of high-rate capability lithium metal polymer electrolytes and breakthroughs in highly ionically conductive all-solid-state polymer electrolytes. In addition, we provide guidance on how to characterize and evaluate polymer electrolytes in lithium metal batteries.

Waugh, John B↗
DOE OSTI2020

Electrochemical Reactivity and Passivation of Silicon Thin-Film Electrodes in Organic Carbonate Electrolytes

This work focuses on the mechanisms of interfacial processes at the surface of amorphous silicon thin-film electrodes in organic carbonate electrolytes to unveil the origins of the inherent nonpassivating behavior of silicon anodes in Li-ion batteries. Attenuated total reflection Fourier-transform infrared spectroscopy, X-ray absorption spectroscopy, and infrared near-field scanning optical microscopy were used to investigate the formation, evolution, and chemical composition of the surface layer formed on Si upon cycling. Herein, we found that the chemical composition and thickness of the solid/electrolyte interphase (SEI) layer continuously change during the charging/discharging cycles. This SEI layer “breathing” effect is directly related to the formation of lithium ethylene dicarbonate (LiEDC) and LiPF6 salt decomposition products during silicon lithiation and their subsequent disappearance upon delithiation. Furthermore, the detected appearance and disappearance of LiEDC and LiPF6 decomposition compounds in the SEI layer are directly linked with the observed interfacial instability and poor passivating behavior of the silicon anode.

25 ENERGY STORAGE↗
DOE OSTI2023

Development of a versatile electrochemical cell for in situ grazing-incidence X-ray diffraction during non-aqueous electrochemical nitrogen reduction

In situ techniques are essential to understanding the behavior of electrocatalysts under operating conditions. When employed, in situ synchrotron grazing-incidence X-ray diffraction (GI-XRD) can provide time-resolved structural information of materials formed at the electrode surface. In situ cells, however, often require epoxy resins to secure electrodes, do not enable electrolyte flow, or exhibit limited chemical compatibility, hindering the study of non-aqueous electrochemical systems. Here, a versatile electrochemical cell for air-free in situ synchrotron GI-XRD during non-aqueous Li-mediated electrochemical N 2 reduction (Li-N 2 R) has been designed. This cell not only fulfills the stringent material requirements necessary to study this system but is also readily extendable to other electrochemical systems. Under conditions relevant to non-aqueous Li-N 2 R, the formation of Li metal, LiOH and Li 2 O as well as a peak consistent with the α-phase of Li 3 N was observed, thus demonstrating the functionality of this cell toward developing a mechanistic understanding of complicated electrochemical systems.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Grand challenges and opportunities in next-generation batteries and technologies

The development of advanced Li-ion batteries and technologies generally addresses one of four objectives: 1) create a higher volumetric energy density and/or specific energy/power, 2) impart intrinsically safer chemistry, 3) produce speedier charging, and 4) utilize less expensive batteries but with competitive/near-competitive performances. Certainly, other factors can play a role as well, dependent on the type of market targeted and the availability of global supplies; however, for widespread adoption, the above points/criteria remain salient. Li-ion is commercially well entrenched in industry for communication and transportation (EV) applications. Nowadays, slight iterations, mostly electrolyte-defined, are incrementally improving safety, cost, and cycle or calendar life. The last point, calendar life, is one that is often overlooked for very high-energy dense Li-ion batteries, because of their reactivity at higher charge (OCV conditions) and elevated temperatures. While cycle life is debated with respect to capacity/energy performance decline, attempts to re-purpose the battery itself or recycle the internal chemical constituents at end of life have considerably grown in the field. Hopefully, energy-neutral processes are also considered in the recycling loop. Nevertheless, the energy storage arena is quite large, and this pursuit hinges on pushing the field in one of many directions, toward loftier objectives. The pursuit of next-generation batteries and technologies must thus delve deeper into new and novel chemistry and electrochemistry to create a world with a neutral, carbon-free environment, and one that is solely sufficient on energy-producing renewables such as the Sun and wind-derived means. The application of electricity and chemistry within our world is thus a 21st century opus.

25 ENERGY STORAGE↗
DOE OSTI2025

Promising performance of sulfide catholytes compared to halide alternatives in NMC811 cathodes for sheet-type sulfide solid-state batteries

Sulfide-based solid-state batteries (SSBs) show promise in achieving energy densities over 350 Wh/kg, yet challenges persist with their incorporation of high-voltage, nickel-rich layered oxide cathodes, such as LiNi₀.₈Mn₀.₁Co₀.₁O₂ (NMC811), due to the poor oxidation stability of sulfide solid-state electrolytes (SSEs) like Li₆PS₅Cl (LPSCl). Although halide SSEs such as Li₃InCl₆ (LIC) and Li₃YCl₆ (LYC) have previously shown promise in stabilizing high-voltage NMC cathodes, our research reveals that sulfide SSE catholytes, particularly when combined with surface-coated NMC cathodes, deliver superior performance. Here, this investigation assesses the cycling stability of various catholytes—LPSCl, LIC, Li₁₀GeP₂S₁₂ (LGPS), combined LIC-LPSCl, and LYC-LPSCl—in SSBs with LiNbO₃-coated NMC811 cathodes against sheet-type LPSCl separators. Findings indicate that while LGPS-based cathodes maintain higher capacity retention, they yield lower deliverable capacity, and LIC cathodes experience significant electrochemical degradation. Importantly, our results underscore that sulfide SSE catholytes, in conjunction with LiNbO₃-coated cathodes, optimize the cathode-electrolyte interphase (CEI), enhancing both kinetics and mass transport. These insights provide a strategic direction for optimizing catholyte composition in the development of sheet-type sulfide-based SSBs.

Catholyte↗
DOE OSTI2023

Accelerated Short Circuiting in Anode-Free Solid-State Batteries Driven by Local Lithium Depletion

“Anode-free” solid-state batteries (SSBs), which have no anode active material, can exhibit extremely high energy density (≈1500 Wh L -1 ). However, there is a lack of understanding of the lithium plating/stripping mechanisms at initially lithium-free solid-state electrolyte (SSE) interfaces because excess lithium metal is often used. Here, it is demonstrated that commercially relevant quantities of lithium (>5 mAh cm -2 ) can be reliably plated at moderate current densities (1 mA cm -2 ) using the sulfide SSE Li 6 PS 5 Cl. Investigations of lithium plating/stripping mechanisms, in conjunction with cryo-ocused ion beam (FIB) imaging, synchrotron tomography, and phase-field modeling, reveal that the cycling stability of these cells is fundamentally limited by the nonuniform presence of lithium during stripping. Local lithium depletion causes isolated lithium regions toward the end of stripping, decreasing electrochemically active area and resulting in high local current densities and void formation. This accelerates subsequent filament growth and short circuiting compared to lithium-excess cells. Despite this degradation mode, here it is shown that anode-free cells exhibit comparable Coulombic efficiency to lithium-excess cells, and improved resistance to short circuiting is achieved by avoiding local lithium depletion through retention of thicker lithium at the interface. These new insights provide a foundation for engineering future high-energy anode-free SSBs.

25 ENERGY STORAGE↗
DOE OSTI2019

Dendrite–Free Potassium Metal Anodes in a Carbonate Electrolyte

Potassium (K) metal anodes suffer from a challenging problem of dendrite growth. In this study, it is demonstrated that a tailored current collector will stabilize the metal plating–stripping behavior even with a conventional KPF 6 –carbonate electrolyte. A 3D copper current collector is functionalized with partially reduced graphene oxide to create a potassiophilic surface, the electrode being denoted as rGO@3D–Cu. Potassiophilic versus potassiophobic experiments demonstrate that molten K fully wets rGO@3D–Cu after 6 s, but does not wet unfunctionalized 3D–Cu. Electrochemically, a unique synergy is achieved that is driven by interfacial tension and geometry: the adherent rGO underlayer promotes 2D layer–by–layer (Frank–van der Merwe) metal film growth at early stages of plating, while the tortuous 3D–Cu electrode reduces the current density and geometrically frustrates dendrites. The rGO@3D–Cu symmetric cells and half–cells achieve state–of–the–art plating and stripping performance. Here, the symmetric rGO@3D–Cu cells exhibit stable cycling at 0.1–2 mA cm –2 , while baseline Cu prematurely fails when the current reaches 0.5 mA cm –2 . The half–cells cells of rGO@3D–Cu (no K reservoir) are stable at 0.5 mA cm –2 for 10 000 min (100 cycles), and at 1 mA cm –2 for 5000 min. The baseline 3D–Cu, planar rGO@Cu, and planar Cu foil fails after 5110, 3012, and 1410 min, respectively.

25 ENERGY STORAGE↗
DOE OSTI2025

Visualizing diverse lithium growth and stripping behaviors in anode-free solid-state batteries with operando X-ray tomography

Anode-free solid-state batteries (SSBs), which eliminate the need for lithium metal use during cell assembly, have the potential to enable high energy densities and simplified manufacturing. However, the factors that control lithium growth/stripping at the anode current collector are not well understood. Here, we use operando X-ray microcomputed tomography to comprehensively image and quantify lithium deposition and stripping under various conditions in three different Li|Li 6 PS 5 Cl|current collector cells, revealing diverse behavior that depends on interface morphology, cell resistance, and solid-state electrolyte (SSE) microstructure. A cell with high resistance exhibits extensive lithium filament growth across the entire current collector interface, with filaments that grow around pre-existing pores in the SSE rather than lithium filling these pores. Lithium filament formation is partially reversible, with the cracks shrinking as lithium metal is stripped. Uniform lithium deposition is achievable at low current densities in low-resistance cells, whereas higher current densities in these cells cause an increase in interfacial roughness, which is correlated with subsequent filamentary growth at the edges of the cell. These results provide insight into filamentary vs. planar lithium growth and highlight that the evolution of lithium is sensitively dependent on SSE microstructure and electrochemical processes.

25 ENERGY STORAGE↗
DOE OSTI2024

All‐Solid‐State Lithium–Sulfur Batteries of High Cycling Stability and Rate Capability Enabled by a Self‐Lithiated Sn‐C Interlayer

Abstract All‐solid‐state lithium–sulfur batteries (ASSLSBs) have attracted intense interest due to their high theoretical energy density and intrinsic safety. However, constructing durable lithium (Li) metal anodes with high cycling efficiency in ASSLSBs remains challenging due to poor interface stability. Here, a compositionally stable, self‐lithiated tin (Sn)‐carbon (C) composite interlayer (LSCI) between Li anode and solid‐state electrolyte (SSE), capable of homogenizing Li‐ion transport across the interlayer, mitigating decomposition of SSE, and enhancing electrochemical/structural stability of interface, is developed for ASSLSBs. The LSCI‐mediated Li metal anode enables stable Li plating/stripping over 7000 h without Li dendrite penetration. The ASSLSBs equipped with LSCI thus exhibit excellent cycling stability of over 300 cycles (capacity retention of ≈80%) under low applied pressure (<8 MPa) and demonstrate improved rate capability even at 3C. The enhanced electrochemical performance and corresponding insights of the designed LSCI broaden the spectrum of advanced interlayers for interface manipulation, advancing the practical application of ASSLSBs.

Ye, Lei↗
DOE OSTI2025

Manganese‐Based Spinel Cathodes: A Promising Frontier for Solid‐State Lithium‐Ion Batteries

Recently, all-solid-state lithium-ion batteries (ASSLIBs), which exhibit improved safety and enhanced energy density compared to conventional commercialized lithium-ion batteries (LIBs), thereby have garnered extensive research interest. Among the promising cathode candidates, Mn-based spinel cathodes LiMn 2 O 4 (LMO) and LiNi 0.5 Mn 1.5 O 4 (LNMO), with the unique characteristics of low cost, structural stability, and 3D Li-ion diffusion channels, have demonstrated excellent performance in LIBs and presented great potential in ASSLIBs applications. However, several challenges, including structural degradations, poor interfacial contact, large interfacial resistance, and Mn-dissolution/diffusion during the electrochemical cycling, hinder their practical applications and commercialization in the ASSLIBs. Particularly, the high-voltage LNMO cathodes suffer from the challenge of electrochemical incompatibility with most of the solid-state electrolytes (SSEs). Herein, the spinel structure, the electrochemical behavior, and the structural degradation of the LMO/LNMO are explored. The characteristics and recent progress of the mitigating strategies to the challenges of various SSEs, including polymer-, oxide-, composite-, sulfide-, halide-, and LiPON-based SSEs, are introduced when paired with LMO/LNMO. Finally, the directions for future research to advance Mn-based spinel cathodes and fulfill the requirements of the next-generation ASSLIBs are also discussed.

Dou, Yu [Concordia University, Montreal, QC (Canad↗
DOE OSTI2024

From Fundamental Interfacial Reaction Kinetics to Macroscopic Current–Voltage Characteristics: Case Study of Solid Acid Fuel Cell Limitations and Possibilities

The unique properties of solid acid electrolytes, in particular CsH 2 PO 4 , are in many ways ideal for fuel cell operation. However, the technology is constrained by high cathode overpotentials. Here a simplified cathode geometry is employed to obtain the fundamental electrochemical parameters (exchange current density and charge transfer coefficient) describing the oxygen reduction reaction (ORR) at the CsH 2 PO 4 -Pt-gas interface. The parameters are incorporated into a 1D model of the voltage–current characteristics of realistic SAFC cathodes, which reproduced the measured polarization behavior of such cathodes without recourse to fitting adjustable parameters. Following this validation, the model is utilized to evaluate the impact of changes to cathode properties, microstructure, and operating conditions. Of these, the charge transfer coefficient, measured to have a value of ≈0.6 for ORR on Pt in the SAFC cathode environment, is found to have the greatest impact on power output. Nevertheless, even without material modifications, a combination of microstructural and operational modifications are identified with projected performance metrics meeting Department of Energy targets (0.8 V at 300 mA cm –2 , and peak power density of 1 W cm –2 ), albeit at high Pt loadings. However, the analysis indicates that truly meaningful advances will likely necessitate the discovery of alternative ORR catalysts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fibrous Materials for Flexible Li–S Battery

The lithium–sulfur (Li–S) battery is an attractive high-energy-density technology for future flexible and wearable electronics, but it is a challenge to simultaneously realize adequate flexibility, stability, and energy density. Recent studies show that fibrous materials are promising to achieve flexible batteries with high energy density, by taking advantages of their intrinsic flexibility, lightweight, large surface area, and cost-effectiveness. With a good tunability of the structure and function, fibrous materials can be suitable to construct various components of a working battery, including current collectors, buffer layers, interlayers, and solid-state electrolytes. In this review, we summarize the recent development of fibrous materials for flexible Li–S batteries, with an emphasis on the discussion of the synthesis and preparation of materials, design of fibrous structures and functionalities, and layout of battery cells for achieving high Coulombic efficiency, long cycle life, and good flexibility.

25 ENERGY STORAGE↗
DOE OSTI2020

Fast Li-Ion Conductivity in Superadamantanoid Lithium Thioborate Halides

Lithium thioborates are promising fast Li-ion conducting materials, with similar properties to their lithium thiophosphate counterparts that have enabled the development of solid-state Li-ion batteries. By comparison, thioborates have scarcely been developed, however, offering new space for materials discovery. In this work, we report a new class of lithium thioborate halides that adopt a so-called supertetrahedral adamantanoid structure that houses mobile lithium ions and halide anions within interconnected 3D structural channels. Investigation of the structure using single-crystal XRD, neutron powder diffraction, and neutron PDF reveals significant lithium and halide anion disorder. The phases are non-stoichiometric, adopting slightly varying halide contents within the materials. These new superadamantanoid materials exhibit high ionic conductivities up to 1.4 mS cm -1 , which can be effectively tuned by the polarizability of the halide anion within the channels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Fabrication of hybrid tin oxide‐cellulose nanocomposite as the flexible and thin supercapacitor

Abstract Microfibrillated cellulose (MFC) with reinforcing effects is a useful building block in the fabrication of flexible and thin supercapacitors. Herein, a hybrid tin oxide‐cellulose nanocomposite was hydrothermally produced and coated on MFC thin films to form a supercapacitor. The hybrid tin oxide‐cellulose thin films were structurally analyzed using scanning electrode microscopy, Fourier transform infrared spectroscopy and x‐ray diffraction. The cellulose thin film with the highest loading of hybrid tin oxide‐cellulose nanocomposite exhibited a specific capacitance of 225.88 F g −1 at 100 mV s −1 and 486.38 F g −1 at 20 mV s −1 in the three‐electrode electrochemical system. In addition, it revealed good cyclic stability up to 40 cycles run continuously with 95% cyclic retention. The high specific capacitance and superior cyclic stability could be related to the enhanced charge mobility and ion diffusion between the solid and electrolyte interface. The cellulose thin film coated with flower‐like hybrid nanocomposite showed great potential in energy storage.

Letchumanan, Iswary↗
DOE OSTI2020

Polyphosphonates as ionic conducting polymers

Polyphosphonates, a class of polymers with the generic formula –[P(R)(X)–OR'O] n –, exhibit a high degree of modularity due to the range of R, R', and X groups that can be incorporated. As such, these polymers may be designed with a polyethylene oxide (PEO) backbone (R' group) and employed as solid polymer electrolytes (SPEs). Two PEO-containing polyphosphonate analogs (R = Ph; X = S or Se) were doped with LiPF 6 and their conductivities were measured. Conductivities were similar (X = S) to or exceeding (X = Se) those of standard PEO systems (just below 10 -4 S/cm at 100°C). Binding models for Li + were generated using 31 P{ 1 H}NMR titration experiments. Binding of Li + by these polyphosphonates followed a positive cooperativity model, and varying the X group (S or Se) affected the observed cooperativity (Hill coefficient = 1.73 and 4.16, respectively). The presence of Se also leads to an increase in conductivity as temperature is raised above the T g , which is likely an effect of reduced Columbic interactions. Finally, because of their modularity and ease with which cation binding can be evaluated using 31 P{ 1 H} NMR titration experiments, polyphosphonates offer a unique approach for the modification of Li + ion battery technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗