SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low speed flow angularity results are presented showing flow direction at the nacelle locations on the Boeing 727-200. Flow angle probes (yawheads) were used for measurements at side and center inlet positions on the aft fuselage. A range of flap settings were tested with flap angles of 0 deg, 15 deg, and 40 deg selected for investigation.
The effect of aircraft operational techniques in the terminal area on community noise impact of future short haul aircraft was investigated. Aircraft equipped with mechanical flap (MF) and aircraft with externally blown flap (EBF) were used to study the noise impact at four U.S. airports. The four airports were: (1) Hanscom Field (Boston), (2) Washington National (D.C.), (3) Midway (Chicago) and (4) Orange County (California). With the exception of Washington National (D.C.), the study showed that a reduction of approximately 40 percent in the number of people highly annoyed can be obtained by using the recommended operational techniques. The evaluation procedures and methodology developed in the study represent an advance in acoustical state-of-the-art and provide an effective and useful tool for determining aircraft noise impact on the airport community.
System identification methods which can extract model rotor paramenters with reasonable accuracy from noise polluted blade flapping transient measurements were developed. Usually parameter identification requires data on the state variables, that is on deflections and on rate of deflections. The small size of rotor models makes it, however, difficult to measure more than the blade flapping deflections. For the computer experiments it was, therefore, assumed that only noisy deflection measurements are available. Parameter identifications were performed for one and two unknown parameters. Both rotating coordinates and multiblade coordinates were used. It was found that data processing with a digital filter allowed by numerical differentiation a sufficiently accurate determination of the rates of deflection and of the accelerations to obtain reasonable parameter estimates with a simple linear estimator.
The reduction of the n per rev. pitch-, roll- and vertical vibrations of an n-bladed rotor by n per rev. sinusoidal variations of the collective and cyclic controls is investigated. The numerical results presented refer to a four-bladed, 7.5-foot model and are based on frequency response tests conducted under an Army-sponsored research program. The following subjects are treated: extraction of the rotor transfer functions (.073R hub flapping and model thrust versus servo valve command, amplitude and phase), calculation of servo commands (volts) required to compensate .073R hub flapping (3P and 5P) and model thrust (4P), evaluation of the effect of the vibratory control inputs on blade loads, and theoretical prediction of the root flapbending moments generated by 0 to 5P perturbations of the feathering angle and rotor angle of attack. Five operating conditions are investigated covering advance ratios from approximately 0.2 to 0.85. The feasibility of vibration reduction by periodic variation on conventional controls is evaluated.
Experimental values of mean and oscillatory shaft force aeroelastic derivatives with respect to cyclic pitch are presented in dimensionless coefficient form for stiff-bladed hingeless rotors operating at high advance ratio. Good agreement with theory is obtained for the 2P components, in rotating axes, of the oscillatory hub moment derivatives. Trends were predicted for the mean components. Experimental plots of the azimuthal distribution of blade flap bending moment due to cyclic pitch are compared with theoretical for high values of flap frequency ratio and advance ratio. Good agreement is found near the blade root. The similarity parameters that should be preserved in the scale model testing of stiff-bladed hingeless rotors at high advance ratio are reviewed, and some aspects of hingeless rotor wind tunnel testing are considered.
This paper is directed to the question of how to represent most efficiently rotor/body coupling in a linear flight dynamics analysis. Rigid body pitch, roll and vertical motions are considered for the rotor/body coupling studies. Flapping stability limits, eigenvalues, transient responses to control step inputs, to step gusts and to random gusts are determined for a hypothetical hingeless compound helicopter operating up to .8 advance ratio. Data are obtained for the basic helicopter and for the craft with two simple control feedback systems. While complete periodic system modeling is necessary for determining flapping stability limits and vibrations, constant system modeling using first order dynamics in each of the multiblade rotor coordinates was found to be adequate for rotor-craft stability and response computations.
A preliminary evaluation is made of the concept of vibration reduction by properly selected oscillatory collective and cyclic control applications. The investigations are based on experimental frequency response data covering advance ratios from approximately 0.2 to 0.85. Because there was no instrumentation for the measurement of the pitch and roll vibrations, these values were obtained by properly adding up the flap-bending moments at 3.3 in. Any other quantity representing pitch/roll vibrations can be compensated for in the same fashion. The calculated control inputs required for vibration reduction stay within acceptable limits. For four of the five conditions tested they are smaller than the values used for the frequency response tests. As to be expected, the compensating controls greatly affect the blade loads, i.e., torsion, flap- and chordwise bending.
Significant reductions in both noise and fuel consumption can be gained through careful tailoring of approach flightpath and airspeed profile, and the point at which the landing gear and flaps are lowered. For example, the noise problem has been successfully attacked in recent years with development of the 'two-segment' approach, which brings the aircraft in at a steeper angle initially, thereby achieving noise reduction through lower thrust settings and higher altitudes. A further reduction in noise and a significant reduction in fuel consumption can be achieved with the 'decelerating approach' concept. In this case, the approach is initiated at high airspeed and in a drag configuration that allows for low thrust. The landing flaps are then lowered at the appropriate time so that the airspeed slowly decelerates to V sub r at touchdown. The decelerating approach concept can be applied to constant glideslope flightpaths or segmented flightpaths such as the two-segment approach.
A quasi-continuous method is developed for solving thin-wing problems. For the purpose of satisfying the wing boundary conditions, the spanwise vortex distribution is assumed to be stepwise-constant, while the chordwise vortex integral is reduced to a finite sum through a modified trapezoidal rule and the theory of Chebyshev polynomials. Wing-edge and Cauchy singularities are acounted for. The total aerodynamic characteristics are obtained by an appropriate quadrature integration. The two-dimensional results for airfoils without flap deflection reproduce the exact solutions in lift and pitching moment coefficients, the leading edge suction, and the pressure difference at a finite number of points. For a flapped airfoil, the present results are more accurate than those given by the vortex-lattice method. The three-dimensional results also show an improvement over the results of the vortex-lattice method. Extension to nonplanar applications is discussed.
The influence of basic parameters that govern flap lag stability of hingeless rotor blades in hover is reviewed, and potential methods are studied for improving the lead lag damping of soft inplane configurations for low thrust conditions. These conditions are relevant for ground and air resonance stability of coupled rotor body dynamic systems. Results indicate that the isolated rotor blade lead lag damping can be usefully increased by a combination of flap lag elastic coupling and pitch lag coupling. For a typical soft inplane configuration, 6% of critical damping can be obtained for moderate pitch lag coupling. For large values of the coupling parameters, the lead lag frequency is substantially reduced at high pitch angles and airfoil stall effects also reduce the lead lag damping.
The feasibility of using control feedback or rotor tip-path-plane motion or body state as a means of altering rotor and fuselage response in a prescribed manner was investigated to determine the practical limitations of in-flight utilization of a digital computer which conditions and shapes rotor flapping and fuselage state information as feedback signals, before routing these signals to the differential servo actuators. The analysis and test of various feedback schemes are discussed. Test results show that a Kalman estimator routine which is based on only the first harmonic contributions of blade flapping yields tip-path-plane coefficients which are adequate for use in feedback systems, at speeds up to 150 kts.
Wind tunnel tests have been made at angles of attack from about -2 deg to about 22 deg at 0 deg angle of sideslip by using a small-amplitude forced-oscillation technique. Models were tested with upper and lower control flaps both deflected and undeflected. The configuration with flaps deflected has positive damping in both pitch and yaw and is stable in both pitch and yaw except at the higher angles of attack where the tail surfaces are submerged in the wake from the body.
The effect of different field lengths, cruise requirements, noise level, and engine cycle characteristics on minimizing fuel consumption and minimizing operating cost at high fuel prices were evaluated for some advanced short-haul aircraft. The conceptual aircraft were designed for 148 passengers using the upper surface-internally blown jet flap, the augmentor wing, and the mechanical flap lift systems. Advanced conceptual STOL engines were evaluated as well as a near-term turbofan and turboprop engine. Emphasis was given to designs meeting noise levels equivalent to 95-100 EPNdB at 152 m (500 ft) sideline.
A flight test investigation of the B-747 vortex wake characteristics was conducted using a T-37B as a probe aircraft. The primary purpose of the program was the validation of the results of B-747 model tests which predicted significant alleviation of the vortex strength when only the inboard flaps were deflected. Measurements of the vortex-induced rolling moments of the probe aircraft showed that the predicted alleviation did occur. The effects of landing gear extension, increased lift coefficient, idle thrust, and sideslip were investigated, and all had an adverse effect on the alleviated condition as evidenced by increased induced rolling moments of the T-37B probe aircraft. Idle thrust also increased the strength of the B-747 wake vortexes with both inboard and outboard flaps extended.
The performance and economics of a twin-engine augmentor wing airplane were evaluated in two phases. Design aspects of the over-the-wing/internally blown flap hybrid, augmentor wing, and mechanical flap aircraft were investigated for 910 m. field length with parametric extension to other field lengths. Fuel savings achievable by application of advanced lift concepts to short-haul aircraft were evaluated and the effect of different field lengths, cruise requirements, and noise levels on fuel consumption and airplane economics at higher fuel prices were determined. Conclusions and recommendations are presented.
The trend toward the utilization of higher maximum lift coefficient with increased aircraft size and cruise velocities is discussed. The impact of this trend on the need for tradeoffs between cruise performance and takeoff, climb, and landing performance is examined. Theoretical methods for the analysis of the two-dimensional characteristics of flap systems are described and compared with experimental data. Four powered-lift concepts are described to outline some of the options currently being developed. Two jet-flap theories are described which provide analytical methods for estimation of the three-dimensional aerodynamic high-lift performance characteristics of powered lift systems.
The development and operational evaluation are discussed of a noise abatement two-segment approach which is safe and operationally acceptable for routine use in air carrier service. An engineering simulation evaluation was conducted; it was found that the entry speed and initial configuration are more important in the DC-8-61 than in the 727 because of the DC-8's aerodynamic cleanliness and drag programming constraints. It was also found that the altitude required for the DC-8 upper and lower transitions is less than the 727 transitions principally due to the pitching moment from the underslung DC-8 engines as compared to the 727 engines which produce no pitching moment with a change in thrust. The 727 approach was a reduced flaps (30 degrees) procedure with a 10-knot airspeed bleed in the lower transition; the DC-8 approach is a full flaps (50 degrees) procedure with constant airspeed established as soon as possible after upper segment transition.
Design, performance, and economic tradeoffs for STOL short-haul systems are presented. The analyses showed that quiet, short-field aircraft can be economically viable and provide benefits to airport congestion and to community noise relief. The objective of the studies was to compare and evaluate propulsive-lift systems and low-wing-loading aircraft provided with ride quality control and gust load alleviation, and to determine fuel consumption and cost tradeoffs, along with recommendations for development of technology, noise criteria, and airport planning. In the low density arena, the optimum aircraft sized for less than 50 passengers have active controls for ride quality and gust alleviation; turboprop propulsion offers significant cost and fuel saving with no appreciable block time penalty for the short typical stage lengths (on the order of 150 miles). In the high density arena, high bypass-ratio fan-powered aircraft, with design cruise speed of 0.7 to 0.75M and range capability to 1500 miles, are considered to be optimum. Field performance of 3000 feet or better can be achieved by the hybrid over-the-wing/internally blown flap concept with viable economics and low fuel consumption. Mechanical flap aircraft with high bypass-ratio engines are indicated to be superior for field lengths of 3500 feet or more. Technology development of propulsive lift is required, and further definition of the best fan-powered engine for low noise and low fuel consumption is needed.