SEARCH · Engineering Papers

Results for “compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Effect of inlet ingestion of a wing tip vortex on turbojet stall margin

A two-dimensional inlet and a turbojet engine were investigated in a Mach 0.4 stream so as to ingest the tip vortex of a forward mounted wing. Results show that ingestion of a wing tip vortex by a turbojet engine can cause a large reduction in engine stall margin. The loss in stall compressor pressure ratio was primarily dependent on vortex location and rotational direction and not on total-pressure variations across the compressor face.

Mitchell, G. A.↗

NASA NTRS1974

Experimental and theoretical investigation of HT-S/PMR-PI composites for application to advanced aircraft engines

A combined experimental and theoretical investigation was performed in order to: (1) demonstrate that high quality angleplied laminates can be made from HT-S/PMR-PI (PMR in situ polymerization of monomeric reactants), (2) characterize the PMR-PI material and to determine the HT-S unidirectional composite properties required for composite micro and macromechanics and laminate analyses, (3) select HT-S/PMR laminate configurations to meet the general design requirements for high-tip-speed compressor blades. The results of the investigation showed that: HT-S/PMR laminate configurations can be fabricated which satisfy the high-tip-speed compressor blade design requirements when operating within the temperature capability of the polymide matrix.

Hanson, M. P.↗

NASA NTRS1974

Fluid mechanics, acoustics, and design of turbomachinery, part 1

A conference was conducted to analyze the effects of air flow on turbomachinery design. The subjects discussed are: (1) equations for compressible flow through turbomachines, (2) influence of axial velocity ratio on cascade performance, (3) three dimensional flow in transonic axial compressor blade rows, (4) prediction of turbulent shear layers in turbomachines, and (5) boundary layers in centrifugal compressors.

Lakshminarayana, B.↗

NASA NTRS1974

Multiple pure tone noise generated by fans at supersonic tip speeds

The existence of clusters of pure tones at integral multiples of shaft speed has been noted for supersonic-tip-speed operation of fans and compressors. A continuing program to explore this phenomenon, often called combination-tone noise, has been in effect for several years. This paper reviews the research program, which involves a wide range of engines, compressor rigs, and special apparatus. Elements of the aerodynamics of the blade-associated shock waves are outlined and causes of blade-to-blade shock inequalities, responsible for the multiple tones, are described.

Sofrin, T. G.↗

NASA NTRS1975

Metal matrix composites for aircraft propulsion systems

Studies of advanced aircraft propulsion systems have indicated that performance gains and operating costs are possible through the application of metal matrix composites. Compressor fan blades and turbine blades have been identified as components with high payoff potential as a result of these studies. This paper will present the current status of development of five candidate materials for such applications. Boron fiber/aluminum, boron fiber/titanium, and silicon carbide fiber/titanium composites are considered for lightweight compressor fan blades. Directionally solidified eutectic superalloy and tungsten wire/superalloy composites are considered for application to turbine blades for use temperatures to 1100 C (2000 F).

Signorelli, R. A.↗

NASA NTRS1975

Analysis of turbofan engine performance deterioration and proposed follow-on tests

Data and engine parts on in-service JT3D and JT8D engines were analyzed and documented relative to engine deterioration. It is concluded that the fan-compressor system of these engines contributes to the long term engine deterioration. An engine test and instrumentation plan was formulated for a proposed follow-on program. The goal of this program is to verify the above conclusion and to attempt to identify more precisely which components of the fan-compressor system are at fault.

Sallee, G. P.↗

NASA NTRS1975

Helium heater design for the helium direct cycle component test facility

The paper describes a helium heater to be used to conduct non-nuclear demonstration tests of the complete power conversion loop for a direct-cycle gas-cooled nuclear reactor power plant. Requirements for the heater include: heating the helium to a 1500 F temperature, operating at a 1000 psia helium pressure, providing a thermal response capability and helium volume similar to that of the nuclear reactor, and a total heater system helium pressure drop of not more than 15 psi. The unique compact heater system design proposed consists of 18 heater modules; air preheaters, compressors, and compressor drive systems; an integral control system; piping; and auxiliary equipment. The heater modules incorporate the dual-concentric-tube 'Variflux' heat exchanger design which provides a controlled heat flux along the entire length of the tube element. The heater design as proposed will meet all system requirements. The heater uses pressurized combustion (50 psia) to provide intensive heat transfer, and to minimize furnace volume and heat storage mass.

Larson, V. R.↗

NASA NTRS1975

Digital TV processing system

Two digital video data compression systems directly applicable to the Space Shuttle TV Communication System were described: (1) For the uplink, a low rate monochrome data compressor is used. The compression is achieved by using a motion detection technique in the Hadamard domain. To transform the variable source rate into a fixed rate, an adaptive rate buffer is provided. (2) For the downlink, a color data compressor is considered. The compression is achieved first by intra-color transformation of the original signal vector, into a vector which has lower information entropy. Then two-dimensional data compression techniques are applied to the Hadamard transformed components of this last vector. Mathematical models and data reliability analyses were also provided for the above video data compression techniques transmitted over a channel encoded Gaussian channel. It was shown that substantial gains can be achieved by the combination of video source and channel coding.

Source record↗

NASA NTRS1976

Development of a Self-contained Heat Rejection Module (SHRM), phase 1

The laboratory prototype test hardware and testing of the Self-Contained Heat Rejection Module are discussed. The purpose of the test was to provide operational and design experience for application to a flight prototype design. It also provided test evaluation of several of the actual components which were to be used in the flight prototype hardware. Several changes were made in the flight prototype design due to these tests including simpler line routing, relocation of remote operated valves to a position upstream of the expansion valves, and shock mounting of the compressor. The concept of heat rejection control by compressor speed reduction was verified and the liquid receiver, accumulator, remote control valves, oil separator and power source were demonstrated as acceptable. A procedure for mode changes between pumped fluid and vapor compression was developed.

Fleming, M. L.↗

NASA NTRS1976

Dynamic blade row compression component model for stability studies

This paper describes a generalized dynamic model which has been developed for use in compression component aerodynamic stability studies. The model is a one-dimensional, pitch-line, blade row, lumped volume system. Arbitrary placement of blade free volumes upstream, within, and downstream of the compression component as well as the removal of bleed flow from the exit of any rotor or stator are model options. The model has been applied to a two-stage fan and an eight-stage compressor. The clean inlet pressure ratio/flow maps and the surge line have been reproduced, thereby validating the capability of the dynamic model to reproduce the steady-flow characteristics of the compression component. A method for determining the onset of an aerodynamic instability which is associated with surge is described. Sinusoidally time-varying inlet and exit boundary conditions have been applied to the eight stage compressor as examples of the manner in which this model may be used for stability studies.

Tesch, W. A.↗

NASA NTRS1975

Fan noise reduction at subsonic and supersonic tip speeds with high Mach number inlets

Results are presented for an experimental study of two fixed geometry inlets and one translating centerbody type inlet tested in an anechoic-chamber transonic-compressor facility. The test vehicle was a 12-inch tip diameter single-stage transonic compressor with 19 rotor blades and 30 stator blades located approximately two chord lengths downstream of the rotor. It is shown that the translating centerbody type of inlet is superior to the collapsing cowl type for noise reduction at high subsonic Mach numbers, both acoustically and aerodynamically. The feasibility of using a high inlet Mach number depends largely on the maximum area ratio requirement (normally at landing). The high inlet Mach numbers are more effective in reducing high-frequency noise than low frequencies and more effective in reducing the blade passage frequency than the overall noise level.

Lumsdaine, E.↗

NASA NTRS1976

Cyclic-load crack growth in ASME SA-105 grade II steel in high-pressure hydrogen at ambient temperature

ASME SA-105 Grade II steel, which is used in high-pressure hydrogen compressor systems, is similar to steels used or considered for use in high-pressure hydrogen storage vessels and pipelines. This paper summarizes the results of a program conducted to provide cyclic-load crack growth rate (da/dN) data for a fracture mechanics analysis of a 15,000 psi hydrogen compressor facility which contains pulse quieter and after-cooler separator vessels constructed of the ASME SA-105 Grade II steel. Included in the program were tests performed to assist in establishing operating procedures that could minimize the effect of hydrogen on crack growth rates during operation.

Walter, R. J.↗

NASA NTRS1976

Transonic performance of Mach 2.65 auxiliary flow axisymmetric inlet

Transonic experimental performance for a large scale Mach 2.65 axisymmetric inlet model with auxiliary airflow systems are presented. The inlet model incorporated both centerbody and cowl auxiliary airflow systems. When the centerbody system was fully open the performance at the simulated compressor face was such that, at 0.10 total pressure distortion the total capture mass flow ratio increased 0.055 and 0.051 and the total pressure recovery increased 0.015 and 0.012 at Mach 0.9 and 1.3, respectively. Flow separation on the centerbody resulted in supercritical centerbody auxiliary throat flow prior to attainment of choked main duct throat flow. Cowl auxiliary airflow had a detrimental effect on compressor-face performance. To overcome the detrimental effect, alternate cowl auxiliary airflow systems are described for efficient merging of auxiliary and main duct airflows and for providing similar auxiliary and main duct throat choking characteristics.

Santman, D. M.↗

NASA NTRS1976

Gas-path seal technology

Improved gas-path seals are needed for better fuel economy, longer performance retention, and lower maintenance, particularly in advanced, high-performance gas turbine engines. Problems encountered in gas-path sealing are described, as well as new blade-tip sealing approaches for high-pressure compressors and turbines. These include a lubricant coating for conventional, porous-metal, rub-strip materials used in compressors. An improved hot-press metal alloy shows promise to increase the operating surface temperatures of high-pressure-turbine, blade-tip seals to 1450 K (2150 F). Three ceramic seal materials are also described that have the potential to allow much higher gas-path surface operating temperatures than are possible with metal systems.

Zuk, J.↗

NASA NTRS1977

Characteristics of random inlet pressure fluctuations during flights of F-111A airplane

Compressor face dynamic total pressures from four F-111 flights were analyzed. Statistics of the nonstationary data were investigated by analyzing the data in a quasi-stationary manner. Changes in the character of the dynamic signal are investigated as functions of flight conditions, time in flight, and location at the compressor face. The results, which are presented in the form of rms values, histograms, and power spectrum plots, show that the shape of the power spectra remains relatively flat while the histograms have an approximate normal distribution.

Costakis, W. G.↗

NASA NTRS1977

Pollution reduction technology program for class T4(JT8D) engines

The technology required to develop commercial gas turbine engines with reduced exhaust emissions was demonstrated. Can-annular combustor systems for the JT8D engine family (EPA class T4) were investigated. The JT8D turbofan engine is an axial-flow, dual-spool, moderate-bypass-ratio design. It has a two-stage fan, a four-stage low-pressure compressor driven by a three-stage low-pressure turbine, and a seven-stage high-pressure compressor driven by a single-stage high-pressure turbine. A cross section of the JT8D-17 showing the mechanical configuration is given. Key specifications for this engine are listed.

Roberts, R.↗

NASA NTRS1978

Gas turbine engine with recirculating bleed

Carbon monoxide and unburned hydrocarbon emissions in a gas turbine engine are reduced by bleeding hot air from the engine cycle and introducing it back into the engine upstream of the bleed location and upstream of the combustor inlet. As this hot inlet air is recycled, the combustor inlet temperature rises rapidly at a constant engine thrust level. In most combustors, this will reduce carbon monoxide and unburned hydrocarbon emissions significantly. The preferred locations for hot air extraction are at the compressor discharge or from within the turbine, whereas the preferred reentry location is at the compressor inlet.

Adamson, A. P.↗

NASA NTRS1978

Computer Program for the Design and Off-Design Performance of Turbojet and Turbofan Engine Cycles

The rapid computer program is designed to be run in a stand-alone mode or operated within a larger program. The computation is based on a simplified one-dimensional gas turbine cycle. Each component in the engine is modeled thermo-dynamically. The component efficiencies used in the thermodynamic modeling are scaled for the off-design conditions from input design point values using empirical trends which are included in the computer code. The engine cycle program is capable of producing reasonable engine performance prediction with a minimum of computer execute time. The current computer execute time on the IBM 360/67 for one Mach number, one altitude, and one power setting is about 0.1 seconds. about 0.1 seconds. The principal assumption used in the calculation is that the compressor is operated along a line of maximum adiabatic efficiency on the compressor map. The fluid properties are computed for the combustion mixture, but dissociation is not included. The procedure included in the program is only for the combustion of JP-4, methane, or hydrogen.

Morris, S. J.↗