Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary layer flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

A quiet flow Ludwieg tube for study of transition in compressible boundary layers: Design and feasibility

Since Ludwieg tubes have been around for many years, and NASA has already established the feasibility of creating quiet-flow wind tunnels, the major question addressed was the cost of the proposed facility. Cost estimates were obtained for major system components, and new designs which allowed fabrication at lower cost were developed. A large fraction of the facility cost comes from the fabrication of the highly polished quiet-flow supersonic nozzle. Methods for the design of this nozzle were studied at length in an attempt to find an effective but less expensive design. Progress was sufficient to show that a quality facility can be fabricated at a reasonable cost.

Schneider, Steven P.↗

Turbulent Friction in the Boundary Layer of a Flat Plate in a Two-Dimensional Compressible Flow at High Speeds

In the present report an investigation is made on a flat plate in a two-dimensional compressible flow of the effect of compressibility and heating on the turbulent frictional drag coefficient in the boundary layer of an airfoil or wing radiator. The analysis is based on the Prandtl-Karman theory of the turbulent boundary later and the Stodola-Crocco, theorem on the linear relation between the total energy of the flow and its velocity. Formulas are obtained for the velocity distribution and the frictional drag law in a turbulent boundary later with the compressibility effect and heat transfer taken into account. It is found that with increase of compressibility and temperature at full retardation of the flow (the temperature when the velocity of the flow at a given point is reduced to zero in case of an adiabatic process in the gas) at a constant R (sub x), the frictional drag coefficient C (sub f) decreased, both of these factors acting in the same sense.

Frankl, F.↗

The three-dimensional boundary layer on a rotating helical blade

The laminar boundary layer on a twisted helical blade is considered. The blade geometry is the same as that proposed by Horlock and Wordsworth (1965). However, the blade is twisted about the leading edge in the manner described by Miyake and Fujita (1974). The flow may be considered to be the analog, in a rotating reference frame, of the flat-plate boundary layer in a stationary frame. It is shown that a coordinate system which is orthogonal in the blade surface may be developed. With the appropriate scaling of the dependent variables a solution for the boundary layer flow is readily obtained. The systems of ordinary differential equations for the stream function of the primary flow and the cross-flow are solved numerically.

Morris, P. J.↗

Turbulent heat transfer prediction method for application to scramjet engines

An integral method for predicting boundary layer development in turbulent flow regions on two-dimensional or axisymmetric bodies was developed. The method has the capability of approximating nonequilibrium velocity profiles as well as the local surface friction in the presence of a pressure gradient. An approach was developed for the problem of predicting the heat transfer in a turbulent boundary layer in the presence of a high pressure gradient. The solution was derived with particular emphasis on its applicability to supersonic combustion; thus, the effects of real gas flows were included. The resulting integrodifferential boundary layer method permits the estimation of cooling reguirements for scramjet engines. Theoretical heat transfer results are compared with experimental combustor and noncombustor heat transfer data. The heat transfer method was used in the development of engine design concepts which will produce an engine with reduced cooling requirements. The Langley scramjet engine module was designed by utilizing these design concepts and this engine design is discussed along with its corresponding cooling requirements. The heat transfer method was also used to develop a combustor cooling correlation for a combustor whose local properties are computed one dimensionally by assuming a linear area variation and a given heat release schedule.

Pinckney, S. Z.↗

Dynamic stall study of a multi-element airfoil

Unsteady flow behavior and load characteristics of a VR-7 airfoil with and without a slat were studied in the water tunnel of the Aeroflightdynamics Directorate, NASA Ames Research Center. Both airfoils were oscillated sinusoidally between 5 and 25 degrees at a Reynolds number of 200,000 to obtain the unsteady lift, drag and pitching moment data. A fluorescing dye was released from an orifice located at the leading edge of the airfoil for the purpose of visualizing the boundary layer and wake flow. The flow field and load predictions of an incompressible Navier-Stokes code based on a velocity-vorticity formulation were compared with the test data. The test and predictions both confirm that the slatted VR-7 airfoil delays both static and dynamic stall as compared to the VR-7 airfoil alone.

Tung, Chee↗

Low frequency vibration induced streaming in a Hele-Shaw cell

When an acoustic wave propagates in a fluid, it can generate a second order flow whose characteristic time is much longer than the period of the wave. Within a range of frequency between ten and several hundred Hz, a relatively simple and versatile way to generate streaming flow is to put a vibrating object in the fluid. The flow develops vortices in the viscous boundary layer located in the vicinity of the source of vibrations, leading in turn to an outer irrotational streaming called Rayleigh streaming. Because the flow originates from non-linear time-irreversible terms of the Navier-Stokes equation, this phenomenon can be used to generate efficient mixing at low Reynolds number, for instance in confined geometries. Here, we report on an experimental study of such streaming flow induced by a vibrating beam in a Hele-Shaw cell of 2 mm span using long exposure flow visualization and particle-image velocimetry measurements. Our study focuses especially on the effects of forcing frequency and amplitude on flow dynamics. It is shown that some features of this flow can be predicted by simple scaling arguments and that this vibration-induced streaming facilitates the generation of vortices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental Study of Hypersonic Inflatable Aerodynamic Decelerator (HIAD) Aeroshell with Axisymmetric Surface Deflection Patterns

A wind tunnel test program was conducted to obtain aeroheating environment data on Hypersonic Inflatable Aerodynamic Decelerator aeroshells with flexible thermal protection systems. Data were obtained on a set of rigid wind tunnel models with surface deflection patterns of various heights that simulated a range of potential in-flight aeroshell deformations. Wind tunnel testing was conducted at Mach 6 at unit Reynolds numbers from 2.1 × 10(exp 6)/ft to 8.3 × 10(exp 6)/ft and angles of attack from 0 deg to 18 deg. Boundary-layer transition onset and global surface heating distribution measurements were performed using phosphor thermography and flow field images were obtained through schlieren photography. Surface deflections were found to both promote early transition of the boundary layer and to augment heating levels for both laminar and turbulent flows. A complimentary computational flow field study was also performed to provide heating predictions for comparison with the measurements as well as boundary layer flow field properties for use in correlating the data. Correlations of the wind tunnel data were developed to predict deflection effects on boundary layer transition and surface heating and were applied to both the wind tunnel test conditions and to the trajectory of NASA's successful IRVE-3 flight test. In general, the correlations produced at least qualitative agreement with the wind tunnel data, although the heating levels were underpredicted for some of the larger surface deflections. For the flight conditions, the correlations suggested that peak heating levels on the leeward side conical flank of the IRVE-3 vehicle may have exceeded those at nose for times late in the trajectory after the peak heating time point. However, the flight estimates were based on a conservative assumption of surface deflection magnitude (i.e., larger) than likely was produced in flight.

Hollis, Brian R.↗

Unsteady aerodynamic behavior of an airfoil with and without a slat

Unsteady flow behavior and load characteristics of a 2D VR-7 airfoil with and without a leading-edge slat were studied in the water tunnel of the Aeroflightdynamics Directorate, NASA Ames Research Center. Both airfoils were oscillated sinusoidally between 5 and 25 deg at Re = 200,000 to obtain the unsteady lift, drag, and pitching moment data. A fluorescent dye was released from an orifice located at the leading edge of the airfoil for the purpose of visualizing the boundary layer and wake flow. The flowfield and load predictions of an incompressible Navier-Stokes code based on a velocity-vorticity formulation were compared with the test data. The test and predictions both confirm that the slatted VR-7 airfoil delays both static and dynamic stall as compared to the VR-7 airfoil alone.

Tung, Chee↗

Reynolds stress development in pressure-driven three-dimensional turbulent boundary layers

The development of the Reynolds stress field was studied for flows in which an initially two-dimensional boundary layer was skewed sideways by a spanwise pressure gradient ahead of an upstream-facing wedge. Two different wedges were used, providing a variation in the boundary-layer skewing. Measurements of all components of the Reynolds stress tensor and all ten triple products were measured using a rotatable cross-wire anemometer. The results show the expected lag of the shear stress vector behind the strain rate. Comparison of the two present experiments with previous data suggests that the lag can be estimated if the radius of curvature of the free-stream streamline is known. The magnitude of the shear stress vector in the plane of the wall is seen to decrease rapidly as the boundary-layer skewing increases. The amount of decrease is apparently related to the skewing angle between the wall and the free stream. The triple products evolve rapidly and profiles in the three-dimensional boundary layer are considerably different than two-dimensional profiles, leaving little hope for gradient transport models for the Reynolds stresses. The simplified model presented by Rotta (1979) performs reasonably well providing that an appropriate value of the T-parameter is chosen.

Anderson, Shawn D.↗

Smoke Study of Nozzle Secondary Flows in a Low-speed Turbine

Still and motion pictures were made of boundary-layer and wake secondary-flow phenomena visualized by smoke. Two annular cascades of turbine nozzles were used, both designed for constant discharge angle but differing in blade shape and suction-surface velocity distribution. Flows were similar to those obtained with pressure and angle measurements at near-sonic airspeeds. Boundary-layer cross-channel and trailing-edge radial flows caused vortices and an accumulation of low-momentum air at the hub, which may affect flow in following blade rows. Motion of a downstream rotor blade row produced pulsations in trailing-edge radial flow. The motion-picture supplement may be obtained on loan from NACA Headquarters, Washington, D.C.

Kofskey, Milton G↗

Building a Practical Natural Laminar Flow Design Capability

A preliminary natural laminar flow (NLF) design method that has been developed and applied to supersonic and transonic wings with moderate-to-high leading-edge sweeps at flight Reynolds numbers is further extended and evaluated in this paper. The modular design approach uses a knowledge-based design module linked with different flow solvers and boundary layer stability analysis methods to provide a multifidelity capability for NLF analysis and design. An assessment of the effects of different options for stability analysis is included using pressures and geometry from an NLF wing designed for the Common Research Model (CRM). Several extensions to the design module are described, including multiple new approaches to design for controlling attachment line contamination and transition. Finally, a modification to the NLF design algorithm that allows independent control of Tollmien-Schlichting (TS) and cross flow (CF) modes is proposed. A preliminary evaluation of the TS-only option applied to the design of an NLF nacelle for the CRM is performed that includes the use of a low-fidelity stability analysis directly in the design module.

Campbell, Richard L.↗

Navier-Stokes solutions for transonic flow over a wing mounted in a tunnel

Three-dimensional viscous flow calculations are performed for a swept, NACA 0012 wing mounted inside a wind tunnel for which detailed experimental data is available. A Runge-Kutta time-stepping scheme is used for obtaining steady-state solutions to the thin-layer Navier-Stokes equations. Free-air comptuations are also performed to assess the wall-interference effects. The effects of grid density and artificial dissipation on the accuracy of numerical results are included. The effect of the wind-tunnel sidewall boundary layer on the flow pattern over the wing surface, particularly in the vicinity of the wing/wall juncture is found to be significant.

Vatsa, V. N.↗

Summary of the 2004 CFD Validation Workshop on Synthetic Jets and Turbulent Separation Control

A CFD validation workshop for synthetic jets and turbulent separation control (CFDVAL2004) was held in Williamsburg, Virginia in March 2004. Three cases were investigated: synthetic jet into quiescent air, synthetic jet into a turbulent boundary layer crossflow, and flow over a hump model with no-flow-control, steady suction, and oscillatory control. This paper is a summary of the CFD results from the workshop. Although some detailed results are shown, mostly a broad viewpoint is taken, and the CFD state-of-the-art for predicting these types of flows is evaluated from a general point of view. Overall, for synthetic jets, CFD can only qualitatively predict the flow physics, but there is some uncertainty regarding how to best model the unsteady boundary conditions from the experiment consistently. As a result. there is wide variation among CFD results. For the hump flow, CFD as a whole is capable of predicting many of the particulars of this flow provided that tunnel blockage is accounted for, but the length of the separated region compared to experimental results is consistently overpredicted.

Rumsey, C. L.↗

Summary of the 2004 CFD Validation Workshop on Synthetic Jets and Turbulent Separation Control

A computational fluid dynamics (CFD) validation workshop for synthetic jets and turbulent separation control (CFDVAL2004) was held in Williamsburg, Virginia in March 2004. Three cases were investigated: synthetic jet into quiescent air, synthetic jet into a turbulent boundary layer crossflow, and flow over a hump model with no-flow-control, steady suction, and oscillatory control. This paper is a summary of the CFD results from the workshop. Although some detailed results are shown, mostly a broad viewpoint is taken, and the CFD state-of-the-art for predicting these types of flows is evaluated from a general point of view. Overall, for synthetic jets, CFD can only qualitatively predict the flow physics, but there is some uncertainty regarding how to best model the unsteady boundary conditions from the experiment consistently. As a result, there is wide variation among CFD results. For the hump flow, CFD as a whole is capable of predicting many of the particulars of this flow provided that tunnel blockage is accounted for, but the length of the separated region compared to experimental results is consistently overpredicted.

Rumsey, C. L.↗

Results from computational analysis of a mixed compression supersonic inlet

A numerical study was performed to simulate the critical flow through a supersonic inlet. This flow field has many phenomena such as shock waves, strong viscous effects, turbulent boundary layer development, boundary layer separations, and mass flow suction through the walls, (bleed). The computational tools used were two full Navier-Stokes (FNS) codes. The supersonic inlet that was analyzed is the Variable Diameter Centerbody, (VDC), inlet. This inlet is a candidate concept for the next generation supersonic involved effort in generating an efficient grid geometry and specifying boundary conditions, particularly in the bleed region and at the outflow boundary. Results for a critical inlet operation compare favorably to Method of Characteristics predictions and experimental data.

Saunders, J. D.↗

On the enhancement of boundary layer skin friction by turbulence: an angular momentum approach

Turbulence enhances the wall shear stress in boundary layers, significantly increasing the drag on streamlined bodies. Other flow features such as free stream pressure gradients and streamwise boundary layer growth also strongly influence the local skin friction. In this paper, an angular momentum integral (AMI) equation is introduced to quantify these effects by representing them as torques that alter the shape of the mean velocity profile. This approach uniquely isolates the skin friction of a Blasius boundary layer in a single term that depends only on the Reynolds number most relevant to the flow's engineering context, so that other torques are interpreted as augmentations relative to the laminar case having the same Reynolds number. The AMI equation for external flows shares this key property with the so-called FIK relation for internal flows (Fukagata et al. , Phys. Fluids , vol. 14, 2002, pp. L73–L76). Without a geometrically imposed boundary layer thickness, the length scale in the Reynolds number for the AMI equation may be chosen freely. After a brief demonstration using Falkner–Skan boundary layers, the AMI equation is applied as a diagnostic tool on four transitional and turbulent boundary layer direct numerical simulation datasets. Regions of negative wall-normal velocity are shown to play a key role in limiting the peak skin friction during the late stages of transition, and the relative strengths of terms in the AMI equation become independent of the transition mechanism a very short distance into the fully turbulent regime. The AMI equation establishes an intuitive, extensible framework for interpreting the impact of turbulence and flow control strategies on boundary layer skin friction.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The simulation of 2D compressible viscous high speed flow by the finite element method

Am implicit/explicit procedure for the solution of problems of two-dimensional steady compressible viscous high-speed flows is presented. In the vicinity of solid walls, a grid which need only exhibit structure in the normal direction is employed while, away from this region, the grid is totally unstructured. The implicit form of the algorithm is used near solid walls, with the grid structure being utilized in an equation solution approach, based upon line relaxation. The explicit form of the algorithm is used elsewhere. Grid adaptation is achieved by means of adaptive remeshing. To illustrate the performance of the proposed method, problems of shock-boundary layer interaction and flow over a simulated forebody at high Mach number are included.

Hassan, O.↗