Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VELOCITY MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

The Effect of Spray Initial Conditions on Heat Release and Emissions in LDI CFD Calculations

The mass and velocity distribution of liquid spray has a primary effect on the combustion heat release process. This heat release process then affects emissions like nitrogen oxides (NOx) and carbon monoxide (CO). Computational Fluid Dynamics gives the engineer insight into these processes, but various setup options exist (number of droplet groups, and initial droplet temperature) for spray initial conditions. This paper studies these spray initial condition options using the National Combustion Code (NCC) on a single swirler lean direct injection (LDI) flame tube. Using laminar finite rate chemistry, comparisons are made against experimental data for velocity measurements, temperature, and emissions (NOx, CO).

Iannetti, Anthony C.↗

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms July 24, 1946 to August 6, 1946 at Orlando, Florida

The results obtained from gust and draft velocity measurements within thunderstorms for the period July 24, 1946 to August 6, 1946 at Orlando, Florida are presented herein. These data are summarized in tables I and II and are of the type presented in reference 1 for previous flights. In two thunderstorm traverses, indications of ambient-air temperature were obtained from photo-observer records. These data are summarized in table III.

Tolefson, Harold B.↗

Quiet, Efficient Fans for Spaceflight: An Overview of NASA's Technology Development Plan

A Technology Development Plan to improve the aerodynamic and acoustic performance of spaceflight fans has been submitted to NASA s Exploration Technology Development Program. The plan describes a research program intended to make broader use of the technology developed at NASA Glenn to increase the efficiency and reduce the noise of aircraft engine fans. The goal is to develop a set of well-characterized government-owned fans nominally suited for spacecraft ventilation and cooling systems. NASA s Exploration Life Support community will identify design point conditions for the fans in this study. Computational Fluid Dynamics codes will be used in the design and analysis process. The fans will be built and used in a series of tests. Data from aerodynamic and acoustic performance tests will be used to validate performance predictions. These performance maps will also be entered into a database to help spaceflight fan system developers make informed design choices. Velocity measurements downstream of fan rotor blades and stator vanes will also be collected and used for code validation. Details of the fan design, analysis, and testing will be publicly reported. With access to fan geometry and test data, the small fan industry can independently evaluate design and analysis methods and work towards improvement.

Koch, L. Danielle↗

Lag Model Predictions for UFAST SBLI Flowfield

Presentation for Shock Boundary Layer Interaction Workshop. Shows results for Lag turbulence model on one of the international workshop test cases the UFAST 8 degree test case. Comparison with PIV velocity measurements as well as computed tunnel wall flowfields are shown, emphasizing that the interaction is a 3D phenomena, and is reasonably well predicted.

Olsen, Mike↗

NASA-DoD Lead-Free Electronics Project: Vibration Test

Vibration testing was conducted by Boeing Research and Technology (Seattle) for the NASA-DoD Lead-Free Electronics Solder Project. This project is a follow-on to the Joint Council on Aging Aircraft/Joint Group on Pollution Prevention (JCAA/JG-PP) Lead-Free Solder Project which was the first group to test the reliability of lead-free solder joints against the requirements of the aerospace/miLItary community. Twenty seven test vehicles were subjected to the vibration test conditions (in two batches). The random vibration Power Spectral Density (PSD) input was increased during the test every 60 minutes in an effort to fail as many components as possible within the time allotted for the test. The solder joints on the components were electrically monitored using event detectors and any solder joint failures were recorded on a Labview-based data collection system. The number of test minutes required to fail a given component attached with SnPb solder was then compared to the number of test minutes required to fail the same component attached with lead-free solder. A complete modal analysis was conducted on one test vehicle using a laser vibrometer system which measured velocities, accelerations, and displacements at one . hundred points. The laser vibrometer data was used to determine the frequencies of the major modes of the test vehicle and the shapes of the modes. In addition, laser vibrometer data collected during the vibration test was used to calculate the strains generated by the first mode (using custom software). After completion of the testing, all of the test vehicles were visually inspected and cross sections were made. Broken component leads and other unwanted failure modes were documented.

Woodrow, Thomas A.↗

Ignition-and-Growth Modeling of NASA Standard Detonator and a Linear Shaped Charge

The main objective of this study is to quantitatively investigate the ignition and shock sensitivity of NASA Standard Detonator (NSD) and the shock wave propagation of a linear shaped charge (LSC) after being shocked by NSD flyer plate. This combined explosive train was modeled as a coupled Arbitrary Lagrangian-Eulerian (ALE) model with LS-DYNA hydro code. An ignition-and-growth (I&G) reactive model based on unreacted and reacted Jones-Wilkins-Lee (JWL) equations of state was used to simulate the shock initiation. Various NSD-to-LSC stand-off distances were analyzed to calculate the shock initiation (or failure to initiate) and detonation wave propagation along the shaped charge. Simulation results were verified by experimental data which included VISAR tests for NSD flyer plate velocity measurement and an aluminum target severance test for LSC performance verification. Parameters used for the analysis were obtained from various published data or by using CHEETAH thermo-chemical code.

Oguz, Sirri↗

Scintillation Effects on Space Shuttle GPS Data

Irregularities in ionospheric electron density result in variation in amplitude and phase of Global Positioning System (GPS) signals, or scintillation. GPS receivers tracking scintillated signals may lose carrier phase or frequency lock in the case of phase sc intillation. Amplitude scintillation can cause "enhancement" or "fading" of GPS signals and result in loss of lock. Scintillation can occur over the equatorial and polar regions and is a function of location, time of day, season, and solar and geomagnetic activity. Mid latitude regions are affected only very rarely, resulting from highly disturbed auroral events. In the spring of 1998, due to increasing concern about scintillation of GPS signals during the upcoming solar maximum, the Space Shuttle Program began to assess the impact of scintillation on Collins Miniaturized Airborne GPS Receiver (MAGR) units that are to replace Tactical Air Control and Navigation (TACAN) units on the Space Shuttle orbiters. The Shuttle Program must determine if scintillation effects pose a threat to safety of flight and mission success or require procedural and flight rule changes. Flight controllers in Mission Control must understand scintillation effects on GPS to properly diagnose "off nominal" GPS receiver performance. GPS data from recent Space Shuttle missions indicate that the signals tracked by the Shuttle MAGR manifest scintillation. Scintillation is observed as anomalous noise in velocity measurements lasting for up to 20 minutes on Shuttle orbit passes and are not accounted for in the error budget of the MAGR accuracy parameters. These events are typically coincident with latitude and local time occurrence of previously identified equatorial spread F within about 20 degrees of the magnetic equator. The geographic and seasonal history of these events from ground-based observations and a simple theoretical model, which have potential for predicting events for operational purposes, are reviewed.

Goodman, John L.↗

The Distribution of the Orbits in the Geminid Meteoroid Stream Based on the Dispersion of their Periods

Geminid meteoroids, selected from a large set of precisely-reduced meteor orbits from the photographic and radar catalogues of the IAU Meteor Data Center (Lindblad et al. 2003), and from the Japanese TV meteor shower catalogue (SonotaCo 2010), have been analyzed with the aim of determining the orbits distribution in the stream, based on the dispersion of their periods P . The values of the reciprocal semi-major axis 1/a in the stream showed small errors in the velocity measurements. Thus, it was statistically possible to also determine the relation between the observed and the real dispersion of the Geminids.

Hajdukova, M., Jr.↗

CFD Validation with LDV Test Data for Payload/Fairing Internal Flow

Flowfield testing of a 1/5th scale model of a payload/fairing configuration, typical of an expendable launch vehicle, has been performed. Two-dimensional (planar) velocity measurements were carried out in four planes with the aid of Laser Doppler Velocimetry (LDV). Computational Fluid Dynamics (CFD) analysis results for the scale model flowfleld are compared with the test data. The CFD results are in general agreement with the test data. The ability of the CFD methodology in identifying the global flow features (including critical points such as vortex, saddle point, etc.) has been demonstrated. Practical problems and difficulties associated with the LDV method applied to the complex geometry under consideration have been summarized.

Kandula, max↗

Can the Nanoflare Model Reproduce Observed Emissions?

All theories that attempt to explain the high temperatures observed in the solar corona are based on short bursts of energy release. The intensities and velocities measured in the core of an active, however, can be steady over many hours of observation. One heating scenario that has been proposed to reconcile such observations with models is the "long nanoflare storm," where short duration heating events occur infrequently on many sub-resolutions strands. In this Letter, we examine the emission measure distribution predicted for such a heating scenario by modeling an arcade of strands in an active region core. Comparisons of the computed emission measure distributions with recent observations indicate that that the long nanoflare storm scenario implies much more 1 MK emission than is actually observed for all plausible combinations of loop lengths, heating rates, and abundances. We conjecture that if the plasma had super coronal abundances, the model may be able to match the observations at low temperatures.

Mulu-Moore, Fana M.↗

A Common Proper Motion Stellar Companion to HAT-P-7

We report that HAT-P-7 has a common proper motion stellar companion. The companion is located at approx. 3.9 arcsec to the east and estimated as an M5.5V dwarf based on its colors. We also confirm the presence of the third companion, which was first reported by Winn et al. (2009), based on long-term radial velocity measurements. We revisit the migration mechanism of HAT-P-7b given the presence of those companions, and propose sequential Kozai migration as a likely scenario in this system. This scenario may explain the reason for an outlier in the discussion of the spin-orbit alignment timescale for HAT-P-7b by Albrecht et al. (2012).

Grady, Carol A.↗

Turbulence Intensity at Inlet of 80- by 120-Foot Wind Tunnel Caused by Upwind Blockage

In order to estimate the magnitude of turbulence in the National Full-Scale Aerodynamics Complex (NFAC) 80- by 120-Foot Wind Tunnel (80 x 120) caused by buildings located upwind from the 80 x 120 inlet, a 150th-scale study was performed that utilized a nominal two-dimensional blockage placed ahead of the inlet. The distance of the blockage ahead of the inlet was varied. This report describes velocity measurements made in the plane of the 80 x 120 model inlet for the case of zero ambient (atmospheric) wind.

80- by 120-Foot Wind Tunnel↗

Global Weather States and Their Properties from Passive and Active Satellite Cloud Retrievals

In this study, the authors apply a clustering algorithm to International Satellite Cloud Climatology Project (ISCCP) cloud optical thickness-cloud top pressure histograms in order to derive weather states (WSs) for the global domain. The cloud property distribution within each WS is examined and the geographical variability of each WS is mapped. Once the global WSs are derived, a combination of CloudSat and Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) vertical cloud structure retrievals is used to derive the vertical distribution of the cloud field within each WS. Finally, the dynamic environment and the radiative signature of the WSs are derived and their variability is examined. The cluster analysis produces a comprehensive description of global atmospheric conditions through the derivation of 11 WSs, each representing a distinct cloud structure characterized by the horizontal distribution of cloud optical depth and cloud top pressure. Matching those distinct WSs with cloud vertical profiles derived from CloudSat and CALIPSO retrievals shows that the ISCCP WSs exhibit unique distributions of vertical layering that correspond well to the horizontal structure of cloud properties. Matching the derived WSs with vertical velocity measurements shows a normal progression in dynamic regime when moving from the most convective to the least convective WS. Time trend analysis of the WSs shows a sharp increase of the fair-weather WS in the 1990s and a flattening of that increase in the 2000s. The fact that the fair-weather WS is the one with the lowest cloud radiative cooling capability implies that this behavior has contributed excess radiative warming to the global radiative budget during the 1990s.

histograms↗

SIM Lite Detection of Habitable Planets in P-Type Binary-Planetary Systems

Close binary stars like spectroscopic binaries create a completely different environment than single stars for the evolution of a protoplanetary disk. Dynamical interactions between one star and protoplanets in such systems provide more challenges for theorists to model giant planet migration and formation of multiple planets. For habitable planets the majority of host stars are in binary star systems. So far only a small amount of Jupiter-size planets have been discovered in binary stars, whose minimum separations are 20 AU and the median value is about 1000 AU (because of difficulties in radial velocity measurements). The SIM Lite mission, a space-based astrometric observatory, has a unique capability to detect habitable planets in binary star systems. This work analyzed responses of the optical system to the field stop for companion stars and demonstrated that SIM Lite can observe exoplanets in visual binaries with small angular separations. In particular we investigated the issues for the search for terrestrial planets in P-type binary-planetary systems, where the planets move around both stars in a relatively distant orbit.

Pan, Xiaopei↗

NASA SPLICE Project: Development and Testing of Precision Landing GN&C Technologies

NASA's technology advancement needs for entry, descent and landing call for high-precision, high-rate sensors that can improve navigation accuracy and vehicle control performance. Higher landing accuracy is required for any future human lander missions, and likely, for most robotic missions 1,2. Sensors and algorithms that significantly reduce navigation errors and can image the local terrain will enable landing at locations of high scientific interest that would otherwise pose significant risk to the vehicle. The Safe and Precise Landing-Integrated Capabilities Evolution project, or SPLICE, is developing precision landing and hazard avoidance (PL&HA) technologies for NASA and for potential commercial space flight missions. SPLICE technologies include sensors, algorithms, advanced space flight computing capabilities, and simulation tools used to integrate and study guidance, navigation, and control (GN&C) system performance. SPLICE efforts include hardware-in-the-loop (HWIL) simulation testing, ground testing, and flight testing, including reuse of hardware from the CoOperative Blending of Autonomous Landing Technologies (COBALT) suborbital flight-test payload3,4. Two of the precise navigation sensors that are being developed and matured within SPLICE are LiDARs. Since 2006, NASA Langley has been developing a Navigation Doppler LiDAR (NDL) for precise velocity measurements, and SPLICE is building an NDL engineering test unit (ETU) that will be brought up to TRL 6 following environmental and high-speed1,2 testing. NASA Goddard is developing a Hazard Detection LiDAR (HD LiDAR) engineering development unit (EDU) for SPLICE that has relevance to future human and robotic lander missions. The HD LiDAR will be flight test and matured to TRL 5.

Restrepo, Carolina I.↗

Orbital Characterization of GJ1108A System, and Comparison of Dynamical Mass with Model-Derived Mass for Resolved Binaries

We report an orbital characterization of GJ1108Aab that is a low-mass binary system in the pre-main-sequence phase. Via the combination of astrometry using adaptive optics and radial velocity measurements, an eccentric orbital solution of e = 0.63 is obtained, which might be induced by the Kozai–Lidov mechanism with a widely separated GJ1108B system. Combined with several observed properties, we confirm that the system is indeed young. Columba is the most probable moving group, to which the GJ1108A system belongs, although its membership to the group has not been established. If the age of Columba is assumed for GJ1108A, the dynamical masses of both GJ1108Aa and GJ1108Ab (M(sub dynamical,GJ1108Aa) = 0.72 ± 0.04 Solar Mass and M(sub dynamical,GJ1108Ab) = 0.30 ± 0.03 Solar Mass) are more massive than what an evolutionary model predicts based on the age and luminosities. We consider that the discrepancy in mass comparison can be attributed to an age uncertainty; the system is likely older than stars in Columba, and effects that are not implemented in classical models such as accretion history and magnetic activity are not preferred to explain the mass discrepancy. We also discuss the performance of the evolutionary model by compiling similar low-mass objects in the evolutionary state based on the literature. Consequently, it is suggested that the current model on average reproduces the mass of resolved low-mass binaries without any significant offsets.

Mizuki, T.↗

Experimental Impacts into Strength-Layered Targets: Ejecta Kinematics

AImpact cratering has dominated the evolution and modification of planetary surfaces through-out the history of the solar system. Impact craters can serve as probes to understanding the details of a planetary subsurface; for example, Oberbeck and Quaide, suggested that crater morphology can be used to estimate the thickness of a regolith layer on top of a more competent unit. Lunar craters show a morphological progression from a simple bowl shape to flat-floored and concentric craters as crater diameter in-creases for a given regolith thickness. The final shape of the impact crater is a result of the subsurface flow-field initiated as the projectile transfers its energy and momentum to the target surface at the moment of impact. Therefore, when a regolith layer is present over a stronger substrate, such as is the case on the lunar surface, the substrate modifies the flow-field and thereby the excavation flow of the crater, which is reflected in the morphology of the final crater. Here we report on a series of experimental impacts into targets composed of a thin layer of loose sand on top of a stronger substrate. We use the Ejection-Velocity Measurement System developed to examine the ejecta kinematics during the formation of these craters.

Anderson, J. L. B.↗

Update on the Juncture Flow PIV Results and Future Plans

A novel, embedded, 2D Particle Image Velocimetry system has been developed and implemented to obtain off-body velocity measurements in the junction of an 8% wing-body configuration in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel. Although the initial purpose for implementing the system during this test was to evaluate system performance and identify potential risks, a considerable amount of data were obtained in the wing-fuselage junction near the trailing edge at a Reynolds Number of 2.4 Million and angle of attack of 5 degrees. In addition to providing notable efficiencies with regard to image acquisition and test operations, the PIV system captured unique details of the flow separation to complement the extensive suite of measurement techniques applied during the test. Instantaneous PIV vector fields reveal that the flow separation is not stationary but rather highly dynamic. Mean flow statistics calculated from the PIV measurements highlight where reverse flow and Reynolds stresses are concentrated in the separated region and agree well with results from the embedded Laser Doppler Velocimeter system and Computational Fluid Dynamics. The comparisons and ional insight gained during this effort will help guide system improvements for the upcoming entry in 2020.

Jenkins, Luther N.↗