Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Efficiency enhancement of InGaN/GaN solar cells with nanostructures

We demonstrate InGaN/GaN multi-quantum-well solar cells with nanostructures operating at a wavelength of 520 nm. Nanostructures with a periodic nanorod or nanohole array are fabricated by means of modified nanosphere lithography. Under 1 sun air-mass 1.5 global spectrum illumination, a fill factor of 50 and an open circuit voltage of 1.9 V are achieved in spite of very high indium content in InGaN alloys usually causing degradation of crystal quality. Both the nanorod array and the nanohole array significantly improve the performance of solar cells, while a larger enhancement is observed for the nanohole array, where the conversion efficiency is enhanced by 51%.

30 DIRECT ENERGY CONVERSION↗

SnO 2 -Catalyzed Oxidation in High-Efficiency CdTe Solar Cells

Interfaces at the front of superstrate CdTe-based solar cells are critical to carrier transport, recombination, and device performance, yet determination of the chemical structure of these nanoscale regions has remained elusive. This is partly due to changes that occur at the front interfaces during high temperature growth and substantive changes occurring during postdeposition processing. In addition, these buried interfaces are extremely difficult to access in a way that preserves chemical information. In this work, we use a recently developed thermomechanical cleaving technique paired with X-ray photoelectron spectroscopy to probe oxidation states at the SnO 2 interface of CdTe solar cells. We show that the tin oxide front electrode promotes the formation of nanometer-scale oxides of tellurium and sulfur. Most oxidation occurs during CdCl 2 /O 2 activation. Surprisingly, we show that relatively low-temperature anneals (180-260 degrees C) used to diffuse and activate copper acceptors in a doping/back contact process also cause significant changes in oxidation at the front of the cell, providing a heretofore missing aspect of how back contact processes can modify device transport, recombination, and performance. Device performance is shown to correlate with the extent of tellurium and sulfur oxidation within this nanometer-scale region. Mechanisms responsible for these beneficial effects are proposed.

14 SOLAR ENERGY↗

Formation of BaSi{sub 2} heterojunction solar cells using transparent MoO{sub x} hole transport layers

Heterojunction solar cells that consist of 15 nm thick molybdenum trioxide (MoO{sub x}, x < 3) as a hole transport layer and 600 nm thick unpassivated or passivated n-BaSi{sub 2} layers were demonstrated. Rectifying current-voltage characteristics were observed when the surface of BaSi{sub 2} was exposed to air. When the exposure time was decreased to 1 min, an open circuit voltage of 200 mV and a short circuit current density of 0.5 mA/cm{sup 2} were obtained under AM1.5 illumination. The photocurrent density under a reverse bias voltage of −1 V reached 25 mA/cm{sup 2}, which demonstrates the significant potential of BaSi{sub 2} for solar cell applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The voltage threshold for arcing for solar cells in LEO: Flight and ground test results

Ground and flight results of solar cell arcing in low Earth orbit (LEO) conditions are compared and interpreted. It is shown that an apparent voltage threshold for arcing may be produced by a strong power law dependence of arc rate on voltage, combined with a limited observation time. The change in this apparent threshold with plasma density is a reflection of the density dependence of the arc rate. A nearly linear dependence of arc rate on density is inferred from the data. A real voltage threshold for arcing for 2 by 2 cm solar cells may exist however, independent of plasma density, near -230 V relative to the plasma. Here, arc rates may change by more than an order of magnitude for a change of only 30 V in array potential. For 5.9 by 5.9 solar cells, the voltage dependence of the arc rate is steeper, and the data are insufficient to indicate the existence of an arcing increased by an atomic oxygen plasma, as is found in LEO, and by arcing from the backs of welded-through substrates.

Ferguson, D. C.↗

The voltage threshold for arcing for solar cells in Leo - Flight and ground test results

Ground and flight results of solar cell arcing in low earth orbit (LEO) conditions are compared and interpreted. It is shown that an apparent voltage threshold for arcing may be produced by a storage power law dependence of arc rate on voltage, combined with a limited observation time. The change in this apparent threshold with plasma density is a reflection of the density dependence of the arc rate. A nearly linear dependence of arc rate on density is inferred from the data. A real voltage threshold for arcing for 2 by 2 cm solar cells may exist however, independent of plasma density, near -230 V relative to the plasma. Here, arc rates may change by more than an order of magnitude for a change of only 30 V in array potential. For 5.9 by 5.9 solar cells, the voltage dependence of the arc rate is steeper, and the data are insufficient to indicate the existence of an arcing increased by an atomic oxygen plasma, as is found in LEO, and by arcing from the backs of welded-through substrates.

Ferguson, Dale C.↗

Progress in InP solar cell research

Progress, in the past year, in InP solar cell research is reviewed. Small area cells with AMO, total area efficiencies of 18.8 percent were produced by OMCVD and Ion Implantation. Larger area cells (2 and 4 sq cm) were processed on a production basis. One thousand of the 2 sq cm cells will be used to supply power to a small piggyback lunar orbiter scheduled for launch in February 1990. Laboratory tests of ITO/InP cells, under 10 MeV proton irradiation, indicate radiation resistance comparable to InP n/p homojunction cells. Computer modeling studies indicate that, for identical geometries and dopant concentrations, InP solar cells are significantly more radiation resistant than GaAs under 1 MeV electron irradiation. Additional computer modeling calculations were used to produce rectangular and circular InP concentrator cell designs for both the low concentration SLATS and higher concentration Cassegrainian Concentrators.

Weinberg, Irving↗

Progress in InP solar cell research

Progress, in the past year, in InP solar cell research is reviewed. Small area cells with AMO, total area efficiencies of 18.8 percent were produced by OMCVD and Ion Implantation. Larger area cells (2 and 4 sq cm) were processed on a production basis. One thousand of the 2 sq cm cells will be used to supply power to a small piggyback lunar orbiter scheduled for launch in February 1990. Laboratory tests of ITO/InP cells, under 10 MeV proton irradiation, indicate radiation resistance comparable to InP n/P homojunction cells. Computer modeling studies indicate that, for identical geometries and dopant concentrations, InP solar cells are significantly more radiation resistant than GaAs under 1 MeV electron irradiation. Additional computer modeling calculations were used to produce rectangular and circular InP concentrator cell designs for both the low concentration SLATS and higher concentration Cassegrainian Concentrators.

Weinberg, I.↗

Ultrasonic Bonding of Solar-Cell Leads

Rolling ultrasonic spot-bonding method successfully joins aluminum interconnect fingers to silicon solar cells with copper metalization. Technique combines best features of ultrasonic rotary seam welding and ultrasonic spot bonding: allows fast bond cycles and high indexing speeds without use of solder or flux. Achieves reliable bonds at production rates without damage to solar cells. Bonding system of interest for all solar-cell assemblies and other assemblies using flat leads (rather than round wires).

Frasch, W.↗

Low cost back contact heterojunction solar cells on thin c-Si wafers. integrating laser and thin film processing for improved manufacturability

An interdigitated back contact (IBC) Si wafer solar cell with deposited a-Si heterojunction (HJ) emitter and contacts is considered the ultimate single junction Si solar cell design. This was confirmed in 2014 by both Panasonic and Sharp Solar producing IBC-HJ cells breaking the previous record Si solar cell efficiency of 25%. But manufacturability at low cost is a concern for the complex IBC-HJ device structure. In this research program, our goals were to addressed the broad industry need for a high-efficiency c-Si cell that overcomes the dominant module cost barriers by 1) developing thin Si wafers synthesized by innovative, kerfless techniques; 2) integrating laser-based processing into most aspects of solar cell fabrication, ensuring high speed and low thermal budgets ; 3) developing an all back contact cell structure compatible with thin wafers using a simplified, low-temperature fabrication process; and 4) designing the contact patterning to enable simplified module assembly. There were a number of significant achievements from this 3 year program. Regarding the front surface, we developed and applied new method to characterize critical interface recombination parameters including interface defect density Dit and hole and electron capture cross-section for use as input for 2D simulation of the IBC cell to guide design and loss analysis. We optimized the antireflection and passivation properties of the front surface texture and a-Si/a-SiN/a-SiC stack depositions to obtain a very low (< 6 mA/cm2) front surface optical losses (reflection and absorption) while maintaining excellent surface passivation (SRV<5 cm/s). We worked with kerfless wafer manufacturers to apply defect-engineering techniques to improve bulk minority-carrier lifetime of thin kerfless wafers by both reducing initial impurities during growth and developing post-growth gettering techniques. This led insights about the kinetics of nickel, chromium, and dislocations in PV-grade silicon and to achieving millisecond lifetimes in kerfless silicon materials. Laser fired contacts to n-Si were developed for the first time using a Al/Sb/Ti metal stack giving contact resistances < 5 mOhm-cm2 when fired through several different dielectric layers. A new 2 step laser+chemical etch isolation technique was developed using a sacrificial top coating which avoids laser damage to Si passivation. Regarding the heterojunction emitter, analysis of front FHJ (1D) and IBC (2D) cells with range of p-layer conditions found that a 2-stage high/low doped p-layer was optimum: the low doped region has lower defects giving higher Voc and the high doped region gave a better contact to the metal. A significant effort was spent studying the patterning process and its contribution to degradation of passivation and reproducibility. Several promising new cleaning, contact and deposition patterning and processing approaches were implemented leading to fabrication of several runs with cells having 19-20% efficiency which were stable over several months. This program resulted in the training and support of 12 graduate students, publication of 21 journal papers and 14 conference papers.

14 SOLAR ENERGY↗

Tunable Bandgap GaInAsP Solar Cells With 18.7% Photoconversion Efficiency Synthesized by Low-Cost and High-Growth Rate Hydride Vapor Phase Epitaxy

As market-dominant Si solar cell technology approaches its practical efficiency limit of 27.1%, a key challenge for the photovoltaic industry is to search for a low-cost ~1.7 eV top cell that can enable cost-competitive tandems with solar-to-electricity conversion efficiency exceeding 30%. III-V semiconductors offer tunable bandgap and unparalleled efficiencies for tandem devices. However, their high manufacturing cost has been the biggest impediment for market entry. Hydride vapor phase epitaxy (HVPE) has recently reemerged as a promising low-cost alternative to incumbent metalorganic chemical vapor deposition (MOCVD) for III-V solar cells. Here, we show the first demonstration of ~1.7 eV GaInAsP solar cells that achieve nearly 19% photoconversion efficiency synthesized by HVPE. The unprecedented growth rate of ~42 um/h achieved via HVPE (~10x faster than conventional MOCVD) allowed the device layers to be deposited in less than seven minutes. Nearly abrupt and chemically distinct heterointerfaces were attained in spite of high-growth rates, which are known to exacerbate phase separation in GaInAsP alloys. Demonstration of ideality factor of n=1 at max power point highlight the advancements in growth optimization and device design. The results presented here highlight a promising path toward tunable bandgap, high-growth rate, low-cost, and high-efficiency GaInAsP devices for direct solar-to-electricity and solar-to-hydrogen conversion.

14 SOLAR ENERGY↗

ATS-5 solar cell experiment results after one year in synchronous orbit

The results of the ATS-5 solar cell experiment after one year in synchronous orbit are reported. A partial failure in the experimental electronics package has caused a loss of data from half the 80 experimental solar cells. Procedures for extracting data due to a partial spacecraft failure are described and discussed. Data from the remaining 40 solar cells, including 15 mounted on a thin flexible structure are analyzed. Data are corrected to a solar intensity of 140 mW/sq cm and a temperature of 25 C. It was found that after one year in synchronous orbit: (1) cells with 1.52-mm-thick coverslides did not show a clear-cut advantage over those with 0.15-mm coverslides, (2) cells with solderless grid lines are degrading at the same rate as are cells with solder-dipped grid lines, (3) cells not quite completely covered with coverslides suffered a large power loss in comparison to cells fully covered, (4) no clear-cut advantage of 10-cm cells over 2-cm cells has yet been observed, (5) cells mounted on the flexible panel with relatively little backshielding did not degrade any faster than those with substantial backshielding, and (6) the flight data in large part confirms the adequacy of the ground-based techniques used in our preflight radiation test program.

Anspaugh, B. E.↗

High Performance Ultrathin GaAs Solar Cells Enabled with Heterogeneously Integrated Dielectric Periodic Nanostructures

Due to their favorable materials properties including direct bandgap and high electron mobilities, epitaxially grown III–V compound semiconductors such as gallium arsenide (GaAs) provide unmatched performance over silicon in solar energy harvesting. Yet, their large-scale deployment in terrestrial photovoltaics remains challenging mainly due to the high cost of growing device quality epitaxial materials. In this regard, reducing the thickness of constituent active materials under appropriate light management schemes is a conceptually viable option to lower the cost of GaAs solar cells. In this work, we present a type of high efficiency, ultrathin GaAs solar cell that incorporates bifacial photon management enabled by techniques of transfer printing to maximize the absorption and photovoltaic performance without compromising the optimized electronic configuration of planar devices. Nanoimprint lithography and dry etching of titanium dioxide (TiO 2 ) deposited directly on the window layer of GaAs solar cells formed hexagonal arrays of nanoscale posts that serve as lossless photonic nanostructures for antireflection, diffraction, and light trapping in conjunction with a co-integrated rear-surface reflector. Systematic studies on optical and electrical properties and photovoltaic performance in experiments, as well as numerical modeling, quantitatively describe the optimal design rules for ultrathin, nanostructured GaAs solar cells and their integrated modules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Increasing photon absorption and stability of PbS quantum dot solar cells using a ZnO interlayer

We compared PbS quantum dot (QD) solar cells with different cathode interlayer materials, namely, LiF and ZnO nanoparticles, using the same device structure. Solar cells fabricated with the ZnO interlayer gave a power conversion efficiency of 4.8%, which is higher (above the experimental variation) than the 4.1% efficiency obtained with a LiF interlayer. We found that the ZnO interlayer alters the spatial distribution of the optical field, leading to an increase in external quantum efficiency in the visible range. Furthermore, devices with ZnO as interlayer showed more stable performance than the ones using LiF, with practically no power conversion efficiency degradation after 1 month inside a N{sub 2} glovebox.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multi–Resonant Mie Resonator Arrays for Broadband Light Trapping in Ultrathin c–Si Solar Cells

Effective photon management is critical to realize high power conversion efficiencies for thin crystalline silicon (c–Si) solar cells. Standard few–100–µm–thick bulk cells achieve light trapping with macroscopic surface textures covered by thin, continuous antireflection coatings. Such sizeable textures are challenging to implement on ultrathin cells. Here, it is illustrated how nanoscale Mie–resonator–arrays with a bimodal size distribution support multiple resonances that can work in concert to achieve simultaneous antireflection and light–trapping across the broad solar spectrum. The effectiveness of these light–trapping antireflection coatings is experimentally demonstrated on a 2.8 µm–thick c–Si solar cell. The measured short–circuit current and corresponding power conversion efficiency are notably improved, achieving efficiencies as high as 11.2%. Measurements of the saturation current density on completed cells indicate that thermal oxides can effectively limit surface recombination. Finally, the presented design principles are applicable to a wide range of solar cells.

14 SOLAR ENERGY↗

Sequentially regular polymer acceptors featuring flexible spacers for high-performance and mechanically robust all-polymer solar cells

Developing high-performance and mechanically robust polymer solar cells (PSCs) is crucial for realizing wearable power sources. While efficient all-polymer solar cells (all-PSCs) can be fabricated from polymerized small-molecule acceptors (PSMAs) with high optical absorption and electron mobilities, they still show limited mechanical robustness. Here, we achieve highly efficient and mechanically robust all-PSCs by designing a PSMA (PYFS-Reg) containing sequence-regular flexible spacers (FSs). The regular incorporation of the FS units into PSMAs is essential in simultaneously improving the electrical and mechanical properties of blend films. As a result, all-PSCs featuring PYFS-Reg achieve a high power conversion efficiency (PCE = 16.1%) and stretchability (crack onset strain (COS) = 22.4%), outperforming PSMAs without FSs (i.e., PYBDT, PCE = 12.6% and COS = 11.7%) or with randomly distributed FSs (i.e., PYFS-Ran, PCE = 12.2% and COS = 18.1%). Importantly, these all-PSCs are fabricated by an environmentally benign, non-halogenated solvent process. To further demonstrate their feasible applications in wearable devices, we construct intrinsically stretchable (IS) all-PSCs by using PYFS-Reg-based active layers, which exhibit a high PCE (10.6%) and excellent device stretchability (strain at PCE 80% = 36.7%).

14 SOLAR ENERGY↗

Highly efficient dye-sensitized solar cells based on HfO{sub 2} modified TiO{sub 2} electrodes

Graphical abstract: Display Omitted Highlights: ► HfO{sub 2} has been used to modify TiO{sub 2} electrodes in dye sensitized solar cells. ► HfO{sub 2} layer increases the dye adsorption. ► Diffusion coefficient (D{sub e}) and lifetime (τ{sub e}) of the photoelectrons were increased. ► Solar cell efficiency (η) was greatly improved from 5.67 to 9.59%. -- Abstract: In this article, we describe the use of hafnium oxide (HfO{sub 2}) as a new and efficient blocking layer material to modify TiO{sub 2} electrodes in dye sensitized solar cells. Different thicknesses of HfO{sub 2} over-layers were prepared by simple dip coating from two different precursors and their effects on the performance of DSSCs were studied. The HfO{sub 2} modification remarkably increases dye adsorption, resulting from the fact that the surface of HfO{sub 2} is more basic than that of TiO{sub 2}. Furthermore, the HfO{sub 2} coating demonstrated increased diffusion coefficient (D{sub e}) and lifetime (τ{sub e}) of the photoelectrons, indicating the improved retardation of the back electron transfer, which increases short-circuit current (J{sub sc}) and open-circuit voltage (V{sub oc}). Thereby, the photo conversion efficiency (η) of the solar cell was greatly improved from 5.67 to 9.59% (an improvement of 69.02%) as the HfO{sub 2} layer was coated over TiO{sub 2} films.

36 MATERIALS SCIENCE↗

Silver-free Metallization Technology for Producing High Efficiency, Industrial Silicon Solar Cells

The goal of this project is to provide a commercially viable Ag-free metallization technology that will both reduce cost and increase efficiency of standard silicon solar cells. By removing silver from the front grid metallization and replacing it with lower cost nickel, copper, and tin metal, the front grid direct materials costs will decrease. This reduction in material costs should provide a path to meeting the Sunshot 2020 goal of 1 dollar / W DC . As of today, plated contacts are not widely implemented in large scale manufacturing. For organizations that wish to implement pilot scale manufacturing, only two equipment choices exist. These equipment manufacturers do not supply plating chemistry. The main goal of this project is to provide a chemistry and equipment solution to the industry that enables reliable manufacturing of plated contacts marked by passing reliability results and higher efficiencies than silver paste front grid contacts. To date, there have been several key findings that point to plated contacts performing equal to or better than the current state of the art silver paste contacts. Poor adhesion and reliability concerns are a few of the hurdles for plated contacts, specifically plated nickel directly on silicon. A key finding of the Phase 1 budget period is that the plated contacts have the same adhesion as the silver paste controls. This is a huge win for plated contacts. With very little optimization work, state of the art electrical results for plated contacts on laser ablated lines have been demonstrated with efficiencies up to 19.1% and fill factors ~80% on grid lines 40-50 um wide. The silver paste controls with similar line widths demonstrate similar electrical results. By optimizing the emitter and grid design for the plated contacts, it is expected that the electrical performance will exceed the silver paste controls. In addition, cells plated using Technic chemistry and equipment pass reliability testing; i.e. 1000 hours damp heat and 200 thermal cycles, with results similar to silver paste control cells. 100 cells have been processed through Technic’s novel demo plating tool built and installed during budget period 2. This plating tool performed consistently from cell to cell, providing gentle handling for the solar cells. An agreement has been signed with a cell manufacturer to process their cells through our plating chemistry and equipment. Their main focus for plated contacts is to reduce the direct materials cost by utilizing nickel, copper, and tin in place of silver paste. Based on current market conditions and cost model calculations, the overall savings offered by plated contacts is only 3.5% dollar/W versus silver paste contacts; however, the direct materials savings depend on the silver market. If silver prices increase, plated contacts may find a wider adoption in the solar industry in order to keep the direct materials costs down for front grid contacts.

14 SOLAR ENERGY↗