Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Airfoil section characteristics at high angles of attack

Information from the literature and from recent investigations is used herein to summarize briefly the effects of airfoil section parameters and flow variables on the aerodynamic characteristics of two-dimensional symmetrical airfoils at high angles of attack. The results presented indicate that airfoil thickness ratio, Reynolds number, Mach number, and surface roughness can all have an important effect on the maximum lift coefficient. The effect of surface roughness seems to be particularly important. Not only can surface roughness cause large decreases in maximum lift coefficient, but also the magnitudes of the effects of Reynolds number, Mach number, and airfoil thickness ratio are much reduced by surface roughness. Beyond the stall, changes in section thickness ratio appear to have little effect on the aerodynamic characteristics of airfoil sections. An investigation of one section through an angle-of-attack range of from 0° to 360° shows that the drag coefficient reaches a value of 2 at an angle of attack of 90°.

Laurence K Loftin, Jr↗

Charts for estimating the hovering endurance of a helicopter

As a means of comparing the performance capabilities of various helicopter propulsion systems, charts have been presented for estimating the hovering endurance of a helicopter in the form of a hovering-endurance parameter as a function of the ratio of total fuel load to helicopter initial weight for a range of initial thrust coefficients from 0.002 to 0.012 and for values of rotor mean lift coefficient from 0.24 to .072. The charts were presented for a helicopter having rotor blades with ideal twist. However, corrections may be applied to the hovering endurance to account for other combinations of twist and taper. The effects of stall and compressibility have been neglected.

HELICOPTERS↗

Equations and procedures for numerically calculating the aerodynamic characteristics of lifting rotors

Equations and procedures are presented for numerically determining the aerodynamic characteristics of lifting rotors. The equations are general and can account for stall and compressibility effects, as well as variations in hub and blade configurations, that are normally omitted from conventional analytical rotor treatments. The application of the method to solution by automatic computing machines is discussed.

LOADS - ROTATING WINGS↗

Analysis of Off-design Performance of a 16-stage Axial-flow Compressor with Various Blade Modifications

The over-all performance of a 16-stage axial-flow compressor was determined with various stator-blade resettings and a reduction in solidity of the rotor blades in the last three stages. It was shown that little control over the sudden change in slope of the surge-limit line at intermediate speeds was obtained with the blade modifications attempted, except that some change in speed at which the change in slope occurred could be effected by stator-blade resettings. Interstage data indicated that the severe surge limit at intermediate speeds was caused by stall of the inlet stage, which, because of stage interaction effects, resulted in a simultaneous decrease in performance of the following five or six stages. Stage data are presented which indicate the flow and pressure-ratio range over which each stage is required to operate at compressor speeds from 50 to 100 percent of design speed.

COMPRESSORS - AXIAL-FLOW↗

Low-speed Aileron Effectiveness as Determined by Force Tests and Visual-flow Observations on a 52 Degree Sweptback Wing with and Without Chord-extensions

The results of an investigation of the effects of leading-edge chord-extensions and extensible leading-edge flaps on the low-speed aileron characteristics of a 52 degrees sweptback wing with circular-arc airfoil sections are presented. A description and illustrations of the vortex flow as it passes over the wing are included. The investigation was conducted at Reynolds numbers of 5.5 times 10(exp 6) and 1.3 times 10(exp 6) and corresponding Mach numbers of 0.11 and 0.065 for an angle-of-attack range of 0 degrees through stall.

CONTROLS, FLAP-TYPE - COMPLETE WINGS↗

Investigation of acceleration characteristics of a single-spool turbojet engine

Operation of a single-spool turbojet engine with constant exhaust-nozzle area was investigated at one flight condition. Data were obtained by subjecting the engine to approximate-step changes in fuel flow, and the information necessary to show the relations of acceleration to the sensed engine variables was obtained. These data show that maximum acceleration occurred prior to stall and surge. In the low end of the engine-speed range the margin was appreciable; in the high-speed end the margin was smaller but had not been completely defined by these data. Data involving acceleration as a function of speed, fuel flow, turbine-discharge temperature, compressor-discharge pressure, and thrust have been presented and an effort has been made to show how a basic control system could be improved by addition of an override in which the acceleration characteristic is used not only to prevent the engine from entering the surge region but also to obtain acceleration along the maximum acceleration line during throttle bursts.

Oppenheimer, Frank L↗

Wind-tunnel investigation of the effects of steady rolling on the aerodynamic loading characteristics of a 45 degree sweptback wing at high subsonic speeds

An investigation has been conducted in the Langley high- speed 7- by 10-foot tunnel to determine the effect of steady rolling on the aerodynamic loading characteristics of a 45° sweptback wing of aspect ratio 4 in combination with a fuselage. The investigation covered Mach numbers of 0.70, 0.85, and 0.91 at angles of attack up to 13°. The r esults indicate that the loss in damping in roll previously noted for this wing is due to stalling of the tip sections. The effects of rolling velocity on the span load distrib~tion can be satisfactorily estimated if measured pressure-distribution data in pitch are available.

James W Wiggins↗

Experimental Investigation of a 16-inch Impulse-type Supersonic-compressor Rotor

Performance data and characteristics of a 16-inch impulse-type supersonic-compressor rotor are presented. The experimental portion of this investigation was conducted in Freon-12. A peak pressure ratio of 3.6 was obtained with an adiabatic efficiency of 0.80 at design conditions. Performance was continuous from impulse operation, at open throttle, to shock-in-rotor operation at the stall condition.

COMPRESSOR FLOW THEORY AND EXPERIMENT↗

Research on the control of airplanes

Our task is to endeavor to obtain precise experimental records of the motion of stalled airplanes, both when left to themselves and when the pilot is trying to control them. The apparatus which we use consists of a box containing tree gyroscopes which are slightly deflected against a spring control when the airplane is turning.

AIRPLANES - LOW-POWER - HILL "PTERODACTYL"↗

Pressure Lag in Tubing Used in Flight Research

Tests described in this report were undertaken to obtain a quantitative measure of the pressure lag in typical pressure-tubing systems used by the Ames Aeronautical Laboratory in flight research investigations. Lag measurements were made with both single-direction and oscillating pressure changes. Single-direction pressure changes were investigated to determine if the lag in orifice-pressure lines and in the research airspeed and altitude measuring systems of pursuit-type airplane undergoing flight tests was sufficient to cause an appreciable error in the record of a sudden pressure change. Oscillating pressure changes were investigated with particular reference to the accuracy of pressure peaks in pressure-distribution measurements during the time of buffeting conditions as found in stalls. (author)

Turner, Howard L↗

Aerodynamic Tests of a Full-scale TBF-1 Aileron Installation in the Langley 16-foot High-Speed Tunnel

The failure of wing panels on a number of TBF-1 and TBM-1 airplanes in flight has prompted several investigations of the possible causes of failure. This report describes tests in the Langley 16-foot high-speed tunnel to determine whether these failures could be attributed to changes in the aerodynamic characteristics of the ailerons at high speeds. The tests were made of a 12-foot-span section including the tip and aileron of the right wing of a TBF-1 airplane. Hinge moments, control-link stresses due to aerodynamic buffeting, and fabric-deflection photographs were obtained at true airspeeds ranging from 110 to 365 miles per hour. The aileron hinge-moment coefficients were found to vary only slightly with airspeed in spite of the large fabric deflections that developed as the speed was increased. An analysis of these results indicated that the resultant hinge moment of the ailerons as installed in the airplane would tend to restore the ailerons to their neutral position for all the high-speed flight conditions covered in the tests. Serious aerodynamic buffeting occurred at up aileron angles of -10 degrees or greater because of stalling of the sharp projecting lip of the Frise aileron. The peak stresses set up in the aileron control linkages in the buffeting condition were as high as three times the mean stress. During the hinge-moment investigation, flutter of the test installation occurred at airspeeds of about 150 miles per hour. This flutter condition was investigated in some detail and slow-motion pictures were made of the motion of the wing tip and aileron. The flutter was found to involve simultaneous normal bending and chordwise oscillation of the wing and flapping of the aileron. The aileron motion appeared to be coupled with this flutter condition and was investigated in some detail and slow-motion pictures were made of the motion of the wing tip and aileron. The flutter was found to involve simultaneous normal bending and chordwise oscillation of the wing and flapping of the aileron. The aileron motion appeared to be coupled with the motion of the wing through the mass unbalance of the aileron in the normal-to-chord plane due to location of the hinge line 2.17 inches below the center of gravity of the aileron. Flutter did not occur when the installation was stiffened to prevent chordwise motion or when the bending frequency of the aileron system was appreciably higher than that of the wing as in the complete airplane installation.

Becker, John V↗

Characteristics of a Boat Type Seaplane During Take-off

This report, on the planing and get-away characteristics of the F-5-L, gives the results of the second of a series of take-off tests on three different seaplanes conducted by the National Advisory Committee for Aeronautics at the suggestion of the Bureau of Aeronautics, Navy Department. The single-float seaplane was the first tested and the twin-float seaplane is to be the third. The characteristics of the boat type were found to be similar to the single float, the main difference being the increased sluggishness and relatively larger planing resistance of the larger seaplane. At a water speed of 15 miles per hour the seaplane trims aft to about 12 degrees and remains in this angular position while plowing. At 2.25 miles per hour the planing stage is started and the planing angle is immediately lowered to about 10 degrees. As the velocity increases the longitudinal control becomes more effective but over control will produce instability. At the get-away the range of angle of attack is 19 degrees to 11 degrees with velocities from the stalling speed through about 25 per cent of the speed range.

Crowley, J W↗

Wind Tunnel Tests on Autorotation and the "Flat Spin."

This report deals with the autorotational characteristics of certain differing wing systems as determined from wind tunnel tests made at the Langley Memorial Aeronautical Laboratory. The investigation was confined to autorotation about a fixed axis in the plane of symmetry and parallel to the wind direction. Analysis of the tests leads to the following conclusions: autorotation below 30 degree angle of attack is governed chiefly by wing profile, and above that angle by wing arrangement. The strip method of autorotation analysis gives uncertain results between maximum C subscript L and 35 degrees. The polar curve of a wing system, and to a lower degree of accuracy the polar of a complete airplane model are sufficient for direct determination of the limits of rotary instability, subject to strip method limitations. The results of the investigation indicate that in free flight a monoplane is incapable of flat spinning, whereas an unstaggered biplane has inherent flat-spinning tendencies. The difficulty of maintaining equilibrium in stalled flight is due primarily to rotary instability, a rapid change from stability to instability occurring as the angle of maximum lift is exceeded. (author)

Knight, Montgomery↗

Pressure Distribution Tests on PW-9 Wing Models from -18 Degree Through 90 Degree Angle of Attack

At the request of the Army Air Corps, an investigation of the pressure distribution over PW-9 wing models was conducted in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics. The primary purpose of these tests was to obtain wind-tunnel data on the load distribution on the cellule to be correlated with similar information obtained in flight tests, both to be used for design purposes. Because of the importance of the conditions beyond the stall as affecting the control and stability, this investigation was extended through 90 degree angle of attack. The results for the range of normal flight have been given in NACA Technical Report No. 271. The present paper presents the same results in a different form and includes, in addition, those over the greater range of angle of attack, -18 degrees through 90 degrees. The results show that: (1) at angles of attack above maximum lift, the biplane upper wing pressures are decreased by the shielding action of the lower wing. (2) the burble of the biplane lower wing, with respect to the angle of attack, is delayed, due to the shielding action of the lower wing. (3) the center of pressure of the biplane upper wing (semispan) is, in general, displaced forward and outward with reference to that of the wing as a monoplane, while for the lower wing there is but slight difference for both conditions. (4) the overhanging portion of the upper wing is little affected by the presence of the lower wing.

Loeser, Oscar E , Jr↗

The characteristics of a Clark y wing model equipped with several forms of low-drag fixed slots

This investigation was undertaken to develop a low-drag fixed slot for an airplane wing which would avoid the complications and maintenance difficulties of the present movable-type Handley Page slot. Tests were conducted on a series of fixed slots in an attempt to reduce the minimum drag coefficient without decreasing the maximum lift coefficient or the stalling angle of the slotted wing. The tests were made in the NACA 5-foot vertical wind tunnel on a Clark Y basic section having a 10-inch chord.

Weick, Fred E↗

Characteristics of Clark Y airfoils of small aspect ratios

This report presents the results of a series of wind tunnel tests showing the force, moment, and autorotational characteristics of Clark Y airfoils having aspect ratios varying from 0.5 to 3. An airfoil of rectangular plan form was tested with rectangular tips, flared tips, and semicircular tips. Tests were also made on one airfoil of circular plan form and two airfoils of elliptical plan form. The tests revealed a marked delay of the stall and a decided increase in values of maximum lift coefficient and maximum resultant force coefficient for aspect ratios of the order of 1 as compared with values for aspect ratios of 2 and 3.

Zimmerman, C H↗

A Flight Investigation of the Lateral Control Characteristics of Short Wide Ailerons and Various Spoilers with Different Amounts of Wing Dihedral

This report presents the results of flight tests made to determine the lateral control characteristics of short wide ailerons and spoilers, as a consequence of the promise shown in wind-tunnel tests by these devices as means of obtaining lateral control, particularly at angles of attack above the stall. Several forms of spoilers, front-hinge, rear-hinge, plain retractable, and saw-tooth retractable were tested alone and in combination with the ailerons. The tests were made with several different amounts of wing dihedral so that the effect of the yawing moments of the different lateral control combinations, which varied from large negative to large positive values, could be evaluated. In conjunction with the tests, observations were made to throw some light on the feasibility of operating the airplane with two controls instead of the present three.

Weick, Fred E↗

The Influence of Tip Shape on the Wing Load Distribution as Determined by Flight Tests

Pressure measurements were made in flight on the right upper wing of an M-3 airplane. The effects of tip plan form, washout, and transverse camber were investigated with eight tip forms in unyawed conditions through the range of positive lift coefficients from zero lift to the stall. The conclusion is that the tip plan form does not influence the span distribution of the coefficients of normal force and moment. It is shown inferentially that temperature, humidity, and the aging of the wood and fabric wing structure used on the M-3 airplane have an appreciable influence on the load distribution.

Rhode, Richard V↗