Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RADIAL VELOCITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Force and moment rotordynamic coefficients for pump-impeller shroud surfaces

Governing equations of motion are derived for a bulk-flow model of the leakage path between an impeller shroud and a pump housing. The governing equations consist of a path-momentum, a circumferential - momentum, and a continuity equation. The fluid annulus between the impeller shroud and pump housing is assumed to be circumferentially symmetric when the impeller is centered; i.e., the clearance can vary along the pump axis but does not vary in the circumferential direction. A perturbation expansion of the governing equations in the eccentricity ratio yields a set of zeroth and first-order governing equations. The zeroth-order equations define the leaking rate and the circumferential and path velocity distributions and pressure distributions for a centered impeller position. The first-order equations define the perturbations in the velocity and pressure distributions due to either a radial-displacement perturbation or a tilt perturbation of the impeller. Integration of the perturbed pressure and shear-stress distribution acting on the rotor yields the reaction forces and moments acting on the impeller face.

Childs, Dara W.↗
NASA NTRS1988

High spatial resolution 10 micron imaging of IRC + 10216

Precise high-resolution 10-micron images of the carbon star IRC + 10216 have been obtained with a scanned linear array. The low noise and high dynamic range of these images permit deconvolution of the telescope point-spread function, revealing the radial brightness distribution of the circumstellar dust shell: approximate reflection symmetry is found in west-east scans, with a distinct division into two components of diameter about 0.40 and 2.2 arcsec. It is shown that this morphology is consistent with published interferometric data that had cast doubt upon an earlier, idealized two-component model. The observed brightness distribution implies that the circumstellar dust density may deviate substantially from the 1/r squared radial dependence expected for spherically symmetric outflow with constant velocity and constant rate of mass loss.

Bloemhof, E. E.↗
NASA NTRS1992

Distribution of ULF energy (f is less than 80 mHz) in the inner magnetosphere - A statistical analysis of AMPTE CCE magnetic field data

Magnetic field measurements made with the AMPTE CCE spacecraft are used to investigate the distribution of ULF energy in the inner magnetosphere. The data base is employed to examine the spatial distribution of ULF energy. The spatial distribution of wave power and spectral structures are used to identify several pulsation types, including multiharmonic toroidal oscillations; equatorial compressional Pc 3 oscillations; second harmonic poloidal oscillations; and nightside compressional oscillations. The frequencies of the toroidal oscillations are applied to determine the statistical radial profile of the plasma mass density and Alfven velocity. A clear signature of the plasma pause in the profiles of these average parameters is found.

Takahashi, Kazue↗
NASA NTRS2000

Effect of Melt Convection at Various Gravity Levels and Orientations on the Forces Acting on a Large Spherical Particle in the Vicinity of a Solidification Interface

Numerical modeling was Undertaken to analyze the influence of both radial and axial thermal gradients on convection patterns and velocities claiming solidification of pure Al and an Al-4 wt% Cu alloy. The objective of the numerical task was to predict the influence of convective velocity on an insoluble particle near a solid/liquid (s/l) interface. These predictions were then be used to define the minimum gravity level (q) required to investigate the fundamental physics of interactions between a particle and a s/l interface. This is an ongoing NASA founded flight experiment entitled "particle engulfment and pushing by solidifying interfaces (PEP)". Steady-state calculations were performed for different gravity levels and orientations with respect to the gravity vector The furnace configuration used in this analysis is the quench module insert (QMI-1) proposed for the Material Science Research Facility (MSRF) on board the International Space Station (ISS). The general model of binary alloy solidification was based on the finite element code FIDAP. At a low g level of 10(exp -4) g(sub o) (g(sub o) = 9.8 m/square s) maximum melt convection was obtained for an orientation of 90 deg. Calculations showed that even for this worst case orientation the dominant forces acting on the particle are the fundamental drag and interfacial forces.

Bune, Andris V.↗
NASA NTRS2001

Soot Surface Growth in Laminar Hydrocarbon/Air Diffusion Flames

The structure and soot surface growth properties of round laminar jet diffusion flames were studied experimentally. Measurements were made along the axes of ethylene-, propylene-propane- and acetylene-benzene-fueled flames burning in coflowing air at atmospheric pressure with the reactants at normal temperature. The measurements included soot structure, soot concentrations, soot temperatures, major gas species concentrations, some radial species (H, OH and O) concentrations, and gas velocities. These measurements yielded the local flame properties that are thought to affect soot surface growth as well as local soot surface growth rates. When present results were combined with similar earlier observations of acetylene-fueled laminar jet diffusion flames, the results suggested that soot surface growth involved decomposition of the original fuel to form acetylene and H, which were the main reactants for soot surface growth, and that the main effect of the parent fuel on soot surface growth involved its yield of acetylene and H for present test conditions. Thus, as the distance increased along the axes of the flames, soot formation (which was dominated by soot surface growth) began near the cool core of the flow once acetylene and H appeared together and ended near the flame sheet when acetylene disappeared. Species mainly responsible for soot oxidation - OH and O2 were present throughout the soot formation region so that soot surface growth and oxidation proceeded at the same time. Present measurements of soot surface growth rates (corrected for soot surface oxidation) in laminar jet diffusion flames were consistent with earlier measurements of soot surface growth rates in laminar premixed flames and exhibited good agreement with existing Hydrogen-Abstraction/Carbon-Addition (HACA) soot surface growth mechanisms in the literature with steric factors in these mechanisms having values on the order of unity, as anticipated.

El-Leathy, A. M.↗
NASA NTRS2003

Soot Surface Growth in Laminar Hydrocarbon/Air Diffusion Flames

The structure and soot surface growth properties of round laminar jet diffusion flames were studied experimentally. Measurements were made along the axes of ethylene-, propylene-propane- and acetylene-benzene-fueled flames burning in coflowing air at atmospheric pressure with the reactants at normal temperature. The measurements included soot structure, soot concentrations, soot temperatures, major gas species concentrations, some radial species (H, OH and 0) concentrations, and gas velocities. These measurements yielded the local flame properties that are thought to affect soot surface growth as well as local soot surface growth rates. When present results were combined with similar earlier observations of acetylene-fueled laminar jet diffusion flames, the results suggested that soot surface growth involved decomposition of the original fuel to form acetylene and H, which were the main reactants for soot surface growth, and that the main effect of the parent fuel on soot surface growth involved its yield of acetylene and H for present test conditions. Thus, as the distance increased along the axes of the flames, soot formation (which was dominated by soot surface growth) began near the cool core of the flow once acetylene and H appeared together and ended near the flame sheet when acetylene disappeared. Species mainly responsible for soot oxidation - OH and 02 were present throughout the soot formation region so that soot surface growth and oxidation proceeded at the same time. Present measurements of soot surface growth rates (corrected for soot surface oxidation) in laminar jet diffusion flames were consistent with earlier measurements of soot surface growth rates in laminar premixed flames and exhibited good agreement with existing Hydrogen-Abstraction/Carbon-Addition (HACA) soot surface growth mechanisms in the literature with steric factors in these mechanisms having values on the order of unity, as anticipated.

El-Leathy, A. M.↗
NASA NTRS1971

The three-dimensional steady radial expansion of a viscous gas from a sonic source into a vacuum.

The three-dimensional steady radial expansion of a viscous, heat-conducting, compressible fluid from a spherical sonic source into a vacuum is analyzed using the Navier-Stokes equations as a basis. It is assumed that the model fluid is a perfect gas having constant specific heats, a constant Prandtl number of order unity, and viscosity coefficients varying as a power of the absolute temperature. Limiting forms for the flow variable solutions are studied for the Reynolds number based on the sonic source conditions, going to infinity and the Newtonian parameter both fixed and going to zero. For the case of the viscosity-temperature exponent between .5 and 1, it is shown that the velocity as well as the pressure approach zero as the radial distance goes to infinity. The formulations of the distinct regions that span the domain extending from the sonic source to the vacuum are presented.

Bush, W. B.↗
NASA NTRS1982

Three dimensional flow field inside the passage of a low speed axial flow compressor rotor

Measurements of the subsonic flow in the rotor passage of a single stage axial flow compressor were made to study the nature of the flow field and to verify the existing numerical codes. The velocity and pressure fields were measured across the entire rotor passage at six axial locations and at five radial locations. A five-hole probe, rotating with the rotor, was used to measure the three components of velocity, the static and the total pressure. The experimental results are compared with the predictions from Katsanis and McNally's computer program. The agreement between the two is good for most of the cases.

Pouagare, M.↗
NASA NTRS1987

Velocity measurements in the plume of an arcjet engine

A nonintrusive technique has been used to conduct a radial survey in the flow field of an arcjet engine plume. The technique measures the Doppler shift of an optically thin line resulting from recombination and relaxation processes in the high Mach number stream, in order to determine flow velocities. Atom temperature can also be calculated from the same Doppler-broadened line widths, when these shifts are measured with a scanning Fabry-Perot spectrometer whose design is presented in detail.

Pivirotto, T. J.↗
DOE OSTI2020

Liquid-phase turbulence measurements in air-water two-phase flows using particle image velocimetry

Liquid-phase turbulence plays a vital role in determining various gas-liquid two-phase flow parameters, such as void fraction distribution, bubble morphology, bubble-bubble interactions, and interfacial area concentration. In this study, a two-phase flow database including both the gas- and liquid-phases measurements was developed focusing on three bubbly flow conditions in an air-water two-phase flow loop with a vertical one-inch diameter circular pipe test section. A particle image velocimetry (PIV) system integrating an optical phase separation method, i.e., the planar laser-induced fluorescence (PLIF) technique using fluorescent particles and optical filtration, was applied to measure the liquid-phase turbulence information, including the time-averaged velocity, Reynolds stress, and turbulent kinetic energy for the liquid phase. The PIV measurements were taken at three ports along the test section at 14.5, 51.5, and 88.5 pipe inner diameters downstream of a bubble injector. In addition, a double-sensor conductivity probe was used to measure radial distributions of the local time-averaged void fraction and gas velocity. The measured liquid-phase turbulence was used to benchmark Sato's turbulence model considering the bubble-induced shear stress for the three tested bubbly flows. The benchmark results showed good agreement between the PIV measurements and model predictions. Lastly, in the two bubbly flows tested that have low void fractions being less than 3%, the effect of the bubble-induced turbulence was found not significant. However, the bubble-induced shear stress becomes important with the increase of the void fraction.

42 ENGINEERING↗
DOE OSTI2021

Chemical enrichment and radial migration in the Galactic disc – the origin of the [αFe] double sequence

The ([α/Fe], [Fe/H]) distribution of Milky Way stars shows at least two distinct sequences, which have traditionally been associated with the thin and thick disc components. The abundance distribution varies systematically with location R and |z| across the Galaxy. We reproduce this using an analytical chemodynamical model that includes the effects of radial migration and kinematic heating. Unlike some earlier models, our scheme does not require a distinct thick disc component emerging from a separate evolutionary path. The proposed model has a continuous star formation history and a continuous age velocity dispersion relation. Moreover, [α/Fe] is constant for stellar ages less than 8 Gyr, but increases sharply for older stars over a time-scale of 1.5 Gyr. The gap between the two sequences is due to this sharp transition. We show that the high-[α/Fe] sequence at the low-metallicity end is simply a pile-up of old stars, but towards the high-metallicity end, the age progressively decreases and stars have small birth radii. Our model successfully explains the uniformity of the locus of the high-[α/Fe] sequence across different locations. The low-[α/Fe] sequence contains stars with different birth radii that owes its existence to radial migration. For the low-[α/Fe] stars, angular momentum is anticorrelated with [Fe/H], while the opposite is true for high-[α/Fe] stars. We show that the later trend can be explained by the increase of circular velocity with time. If radial migration is not included, the model fails to generate the double sequence and instead shows only a single sequence. Our simple scheme has major advantages over earlier chemodynamical models, as we show.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1982

Three dimensional mean velocity and turbulence characteristics in the annulus wall region of an axial flow compressor rotor passage

The experiment was performed using the rotating hot-wire technique within the rotor blade passage and the stationary hot-wire technique for the exitflow of the rotor blade passage. The measurements reveal the effect of rotation and subsequent flow interactions upon the rotor blade flowfield and wake development in the annulus-wall region. The flow near the rotor blade tips is found to be highly complex due to the interaction of the annulus-wall boundary layer, the blade boundary layers, the tip leakage flow, and the secondary flow. Within the blade passage, this interaction results in an appreciable radial inward flow as well as a defect in the mainstream velocity near the mid-passage. Turbulence levels within this region are very high. This indicates a considerable extent of flow mixing due to the viscous flow interactions. The size and strength of this loss core is found to grow with axial distance from the blade trailing edge. The nature of the rotor blade exit-flow was dominated by the wake development.

Davino, R.↗
NASA NTRS2004

A Rotary Flow Channel for Shear Stress Sensor Calibration

A proposed shear sensor calibrator consists of a rotating wheel with the sensor mounted tangential to the rim and positioned in close proximity to the rim. The shear stress generated by the flow at the sensor position is simply tau(sub omega) = (mu)r(omega)/h, where mu is the viscosity of the ambient gas, r the wheel radius, omega the angular velocity of the wheel, and h the width of the gap between the wheel rim and the sensor. With numerical values of mu = 31 (mu)Pa s (neon at room temperature), r = 0.5 m, omega = 754 /s (7200 rpm), and h = 50.8 m, a shear stress of tau(sub omega) = 231 Pa can be generated. An analysis based on one-dimensional flow, with the flow velocity having only an angular component as a function of the axial and radial coordinates, yields corrections to the above simple formula for the curvature of the wheel, flatness of the sensor, and finite width of the wheel. It is assumed that the sensor mount contains a trough (sidewalls) to render a velocity release boundary condition at the edges of the rim. The Taylor number under maximum flow conditions is found to be 62.3, sufficiently low to obviate flow instability. The fact that the parameters entering into the evaluation of the shear stress can be measured to high accuracy with well-defined uncertainties makes the proposed calibrator suitable for a physical standard for shear stress calibration.

Zuckerwar, Allan J.↗
NASA NTRS1998

Radial Distribution of Electron Spectra from High-Energy Ions

The average track model describes the response of physical and biological systems using radial dose distribution as the key physical descriptor. We report on an extension of this model to describe the average distribution of electron spectra as a function of radial distance from an ion. We present calculations of these spectra for ions of identical linear energy transfer (LET), but dissimilar charge and velocity to evaluate the differences in electron spectra from these ions. To illustrate the usefulness of the radial electron spectra for describing effects that are not described by electron dose, we consider the evaluation of the indirect events in microdosimetric distributions for ions. We show that folding our average electron spectra model with experimentally determined frequency distributions for photons or electrons provides a good representation of radial event spectra from high-energy ions in 0.5-2 micrometer sites.

Cucinotta, Francis A.↗
NASA NTRS1975

Turbulent flow between a rotating disk and a parallel wall

A scalar effective viscosity method is used to calculate the incompressible flow in the gap between two infinite, parallel smooth disks, one of them rotating and the other stationary. The flow is calculated for two values of the gap Reynolds number omega(s squared)/nu, namely 296 and 2852, where omega is the disk angular velocity, s the gap width, and nu the kinematic viscosity of the fluid; and over a range of radial Reynolds number omega(r squared)/nu from 0 to 10 million, where r is the radius from the axis of rotation. A numerical shooting technique is used to match the two boundary-layer flows arising on the disk and wall. Gradual transition is assumed for radial Reynolds numbers from 160,000 to 250,000. The results are in good agreement with Daily and Nece's measurements of velocity profiles and disk friction drag for enclosed rotating disks, and at sufficiently large radius the local skin friction approaches that of turbulent Couette flow.

Cooper, P.↗
NASA NTRS1989

Radial mixing of material in the asteroidal zone

The asteroid belt shows radial zoning of compositional structure. The most abundant types are successively S, C, and P types from the inner to the outer parts of the main belt, and D type in the Trojan clouds. This paper examines processes for producing this structure before, during, and after the accretion of asteroids. The initial structure is established by temperature and composition gradients in the turbulent solar nebula during the collapse of the presolar cloud. The radial scale of the zoning, comparable to the disk thickness, favors disk models with relatively low turbulent viscosity. Radial decay of solid bodies due to gas drag during settling to the central plane and planetesimal formation probably causes only a small degree of mixing, due to the systematic nature of drag-induced motions. The formation of Jupiter causes scattering of massive planetesimals from that planet's zone through the asteroid zone. The present random velocities of asteroids resulting from that stirring process are consistent with the radial scale of transitions between compositional types.

Ruzmaikina, T. V.↗
DOE OSTI2025

Cold-Sprayed NMC622 Composite as a Cathode for Lithium-Ion Batteries

The growing demand for high-energy, low-cost lithium-ion batteries (LIBs) to power electric vehicles (EVs) necessitates advances in both materials and manufacturing processes. Conventional cathode fabrication methods, such as slurry casting and drying, are energy-intensive and pose challenges for scalability and environmental compliance. In this study, we propose cold-spray (CS) deposition as a solvent-free approach for fabricating LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) composite cathodes. Powder blends of NMC622, poly(vinylidene fluoride) (PVDF), and carbon black (CB) are directly deposited onto stainless steel and Inconel substrates under varied gas temperatures, pressures (and thus velocities), and standoff distances. The effects of temperature on the deposit morphology, coating density, and volume are systematically investigated. Computational fluid dynamics simulations reveal that increasing the gas temperature enhances the particle velocity, narrows the spray angle, and reduces the mass concentration radially at the nozzle outlet. CS deposition results in a dense cathode microstructure, accompanied by fracture in polycrystalline NMC622 particles. X-ray diffraction analysis further verifies that there are no phase changes during the deposition process. The electrochemical performance of the cold-sprayed cathodes reveals an initial capacity of approximately 96 mAh g –1 for single-crystal NMC622 and 167 mAh g –1 for polycrystalline NMC622. While these values are modest compared to state-of-the-art slurry-cast cathodes, which typically exhibit 180–200 mAh g –1 under optimized conditions. The results demonstrate a competitive performance given the solvent-free nature of the CS process and compare favorably with tape-cast samples made from identical feedstock. In conclusion, he CS process enables the formation of dense, binder-integrated cathode coatings without the need for solvent processing, offering a promising pathway for scalable, energy-efficient dry electrode manufacturing of next-generation LIBs.

Batteries↗