Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DUCTILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Nanoscale characterization of engineered cementitious composites (ECC)

Engineered cementitious composites (ECC) are ultra-ductile fiber-reinforced cementitious composites. The nanoscale chemical and mechanical properties of three ECC formulae (one standard formula, and two containing nanomaterial additives) were studied using nanoindentation, electron microscopy, and energy dispersive spectroscopy. Nanoindentation results highlight the difference in modulus between bulk matrix ({approx} 30 GPa) and matrix/fiber interfacial transition zones as well as between matrix and unreacted fly ash ({approx} 20 GPa). The addition of carbon black or carbon nanotubes produced little variation in moduli when compared to standard M45-ECC. The indents were observed by electron microscopy; no trace of the carbon black particles could be found, but nanotubes, including nanotubes bridging cracks, were easily located in ultrafine cracks near PVA fibers. Elemental analysis failed to show a correlation between modulus and chemical composition, implying that factors such as porosity have more of an effect on mechanical properties than elemental composition.

36 MATERIALS SCIENCE↗

Influence of the micro- and nanoscale local mechanical properties of the interfacial transition zone on impact behavior of concrete made with different aggregates

The influence of the microscale local mechanical properties of the interfacial transition zone (ITZ) on macro-level mechanical response and impact behavior is studied for concretes made with copper slag and gravel aggregates. 3D nanotech vertical scanning interferometry, scanning electron microscopy coupled with energy dispersive X-ray micro-analysis, digital image analysis, and 3D X-ray computed tomography were used to characterize the microstructures and the ITZs. It was deduced that a stronger and denser ITZ in the copper slag specimen would reduce its vulnerability to stiffness loss and contribute to its elastic and more ductile response under impact loading. The analysis also indicated that a significant degeneration in the pore structure of the gravel specimen associated with a relatively weaker and non-homogeneous ITZ occurred under impact. Finally, it was also concluded that increased roughness of ITZ may contribute to the load-carrying capacity of concrete under impact by improving contact point interactions and energy dissipation.

36 MATERIALS SCIENCE↗

Role of porosity on the stiffness and stability of (001) surface of the nanogranular C–S–H gel

We present here a nanoscale modeling of the bulk and surface states of the nanogranular Calcium Silicate Hydrate (C–S–H) gel. Regarding the mechanical properties as well as porosity, we identify two main phases: a ductile one, for a porosity from 12.4% to 27% and a brittle phase for a porosity lower than 12.4% or higher than 27%. Particularly, our calculations show that 20% of gel porosity gives a better structural stability to C–S–H and a higher stiffness. Besides, we have explored the (001) surface of C–S–H gel at the nanoscale level and have proved that more water on the surface will stabilize thermodynamically the nanostructure. This means that adsorbed H{sub 2}O molecules lead to the coexistence of Si–OH and Ca–OH groups on the surface. The calcium-terminated plane is a polar and unstable surface, and will either reconstruct to neutralize the dipole moment or adsorb ions to remove it. Our results also show that the (001) surface of low density C–S–H tends to be more stable than the surface of high density phase since the obtained surface energy decreases with increasing gel porosity.

36 MATERIALS SCIENCE↗

Piezoelectric response and failure behavior of cement paste under external loading

We study the elastic behavior and rupture mechanism of Calcium Silicate Hydrates (C-S-H) in response to tensile loading. For the three tensile axes, initial defects are spotted in the interlayer regions. However, the crack propagation is rather different depending on the axis of tensile. The cup-and-cone failure surface shows the ductile feature of C-S-H in the x and y directions; while the devastating rupture mode confirms the brittle feature of C-S-H in the z direction. Piezoelectricity was investigated using the charge fluctuation method. The polarization variation in response to small strain was also investigated and piezoelectric coefficients were derived. Furthermore, dependence of elastic and piezoelectric properties over external pressure was analyzed. Results reveal an improvement of the mechanical properties and the ultimate strength especially in the z direction; whereas the non-piezoelectricity remains unchanged despite the rearrangement of atoms induced by the external applied pressure.

36 MATERIALS SCIENCE↗

Assessment of asymmetrical rheological behavior of cementitious material for 3D printing application

Among the multiplicity of construction methods based on digital concrete technologies, the most common one remains the extrusion-based process. Two opposed strategies have been developed in order to print a concrete structure using extrusion: the first one emphasizes the ease-of-pumping of material which is massively accelerated to ensure the stability of the structure, when leaving the extruder; the second one uses a firm mortar able to sustain the own weight of the structure during the printing, without requiring any accelerator. Both methods have their pros and cons and don't imply the same rheological requirements. Most of the recent literature assumes that both types of material (fluid and firm) follow the same trend of behavior and obey to the Von Mises plasticity criterion, while it has been demonstrated that firm cement-based materials can exhibit a pressure dependent behavior. Moreover, rheological study is mainly based on shear rheometry, while the extrusion-based printing process requires a description of the rheological behavior in compression to predict the global stability of the structure, and in tension to prevent cracks formation. This paper investigates the fresh behavior of cement paste and mortar under different solicitations (shear, compression, tension) for different water to cement ratios. The analysis of these results allows to describe the transition between a ductile fluid material (symmetrical in tension and compression) that obeys to a Von Mises plasticity criterion, and a brittle and firm material (asymmetrical in tension and compression) that requires a pressure dependent plasticity criterion in order to predict its strength under a given solicitation.

36 MATERIALS SCIENCE↗

3D-printable engineered cementitious composites (3DP-ECC): Fresh and hardened properties

3D printing (3DP) is an emerging digital construction method for concrete materials. A major impediment to efficient 3D concrete printing (3DCP) is the need for steel reinforcement, the placement of which is incompatible with the 3DP process. Unlike plain concrete, ductile self-reinforced engineered cementitious composite (ECC) holds promise to remove the dependence on steel reinforcement. The objective of this research is to develop a 3D-printable ECC (3DP-ECC). The fresh rheological and hardened mechanical properties of 3DP-ECC are investigated. The robotically printed tensile specimens demonstrated the familiar multiple microcracking and strain-hardening behavior of conventionally cast ECC. Significant orthotropy is revealed in the compressive properties. The interface between printed layers is found to be toughened by a printed groove-tongue joint. The developed 3DP-ECC was used to print a twisted column with 150 layers, reaching a height of 1.5 m. This research lays the groundwork for efficient robotically 3D-printed structures of complex shapes.

36 MATERIALS SCIENCE↗

Fracturing process of micro-concrete under uniaxial and triaxial compression: Insights from in-situ X-ray mechanical tests

This paper presents an experimental study of concrete at meso-scale (aggregates, macro-pores and mortar matrix) in order to get a better understanding of the local failure mechanisms known to drive the macroscopic mechanical behaviour of the material. The main originality comes from conducting in-situ X-ray mechanical tests on micro-concrete samples of realistic composition (including cement, sand, aggregates and water), under uniaxial compression and, for the first time, under triaxial compression at 5 MPa, 10 MPa and 15 MPa confining pressures. A timeseries analysis of the set of 3D images coming from each test allows for the measurement of the 3D kinematic fields (displacement and strain fields) throughout the experiments. The different failure patterns observed for each loading path are discussed, along with a quantification of the 3D fracturing processes at the scale of the largest heterogeneities (aggregates and macro-pores). With an increasing level of confinement, the transition from brittle to ductile response is observed, as well as an increase of the strength of the material. The pronounced impact of the meso-scale heterogeneities of concrete on their local failure mechanisms is highlighted. It is shown that strain localisation mainly originates between aggregates and mortar matrix, with the shape and location of the largest aggregates and macro-pores essentially driving the propagation of the cracking network.

36 MATERIALS SCIENCE↗

Effect of various post-extrusion tempering on performance of AA2024 tubes fabricated by shear assisted processing and extrusion

In this report aluminum alloy 2024 (AA2024) tubes were extruded using the shear assisted processing and extrusion (ShAPE) method. As a ubiquitous aerospace alloy, AA2024 has reached a high degree of maturity with respect to manufacturing processes, alloy chemistry and heat treatment to maximize material strength. Therefore, over the eight decades since the introduction of this alloy, the mechanical properties have plateaued, and the extrusion speed has reached a 3.5 m/min ceiling using conventional extrusion. The ShAPE technique enabled an extrusion speed of AA2024 up to 7.4 m/min at 480 °C which is surpassing the extrudability chart of this alloy. Variation of the standard T3510 and T8510 post extrusion heat treatments were applied to improve the mechanical performance of the ShAPE extruded AA2024 tube. The ultimate tensile strength and yield strength of AA2024-T8510 ShAPE extruded tube are 522.0 ± 3.3 MPa and 510.7 ± 3.3 MPa, which are respectively 18% and 32% higher than ASM-typical and ASTM minimum values. The elongation at break of ShAPE extruded AA2024-T8510 tubes is two times higher than the ASM-typical and ASTM-minimum values. This improved ductility is attributed to the refinement of grain size and secondary phases as well as due to the uniform dispersion of sub-micron strengthening precipitates formed during the ShAPE process.

42 ENGINEERING↗

An overlapping Domain Decomposition preconditioning method for monolithic solution of shear bands

Metals subjected to high strain rate impact often exhibit a sudden and profound drop in the material’s load bearing capability, a ductile failure phenomenon known as shear banding. Shear bands, characterized as material instabilities, are driven by shear heating and described as narrow regions that have sustained intense plastic deformation and high temperature rise. This coupled thermo-mechanical localization problem can be formulated as a nonlinear system with two balance equations, momentum and energy, and two constitutive laws for elasticity and plasticity. Here in our formulation, mixed finite elements are used to discretize the equations in space and an implicit finite difference scheme is used to advance the system in time, where at every time step, a Newton type method is used to solve the system monolithically. To that end, a block Jacobian matrix is formed analytically using Gâteaux derivatives. The resulting Jacobian is sparse, nonsymmetric and its sparsity pattern and eigenvalue content vary with the different stages of shear bands formation, consequently posing a significant challenge to iterative solvers. To address this issue, an overlapping Domain Decomposition preconditioner that takes into account the physics of shear bands and the domain in which it forms, is proposed. The key idea is to resolve the shear band domain accurately while only solving the remaining domain approximately, with selective updates when necessary. The preconditioner is formed on the basis of an additive Schwartz method that is applied to a Schur complement partition of the system. The proposed preconditioner is implemented in parallel and tested on three different benchmark problems as compared against off-the-shelf solvers. We study the effect of h- and k-refinement that are obtained from Isogeometric discretizations of the system, the overlapping strategy and its parallel performance. Excellent performance is demonstrated in serial and parallel on all benchmark examples.

42 ENGINEERING↗

Influence of Various Material Design Parameters on Deformation Behaviors of TRIP Steels

In this paper, the microstructure-based finite element modeling method is used as a virtual design tool in investigating the respective influence of various material design parameters on the deformation behaviors of transformation induced plasticity (TRIP) steels. For this purpose, the separate effects of several different material design parameters, such as the volume fraction and stability of austenite phase and the strengths of the constituent phases, on the ultimate tensile strength (UTS) and ductility/formability of TRIP steels are quantitatively examined using different representative volume elements (RVEs) representing different TRIP steels. The computational results suggest that higher austenite stability is helpful in enhancing the ductility and formability of TRIP steels by delaying the martensitic transformation to a later stage, whereas increase of austenite volume fraction and/or ferrite strength alone is not beneficial to improve the performance of TRIP steels. The results in this study also indicate that various material design parameters must be adjusted concurrently to develop high performance TRIP steels. For example, the austenite strength should increase over the ferrite strength in order to induce the gradual/smooth martensitic transformation, and the strength disparity between the ferrite and the freshly-formed martensite phases should decrease in order to avoid higher stress/strain concentration along the phase boundaries. The modeling approach and results presented in this paper can be helpful in providing the deformation fundamentals for the development of high performance TRIP steels.

Austenite stability↗

Predicting Tensile Stretchability of Trimmed AA6111-T4 Sheets

An integrated manufacturing process simulation framework has been developed to predict the trimmed edge tensile stretchability of AA6111-T4 sheets by incorporating the burr geometry, damage, and plastic strain from trimming simulations into subsequent tensile stretchability simulations. The influence of the trimming die clearances on the predicted tensile stretching ductility (stretchability) is studied and quantitatively compared with experimental measurements. Stretchability is found to decrease with increasing cutting clearances, and simulation results have successfully captured experimentally observed edge crack initiation and failure mode variations for different trimming clearances. Subsequent computational sensitivity studies reveal that while deburring of previously trimmed edges has little influence on tensile stretchability, removal of trimmed edge initial plastic strain may significantly enhance the subsequent trimmed edge stretchability.

Aluminum alloys↗

Microstructure Based Modeling of β Phase Influence on Mechanical Response of Cast AM Series Mg Alloys

Magnesium alloys have become popular alternatives to aluminums and steels for the purpose of vehicle light-weighting. However, Mg alloys are hindered from wider application due to limited ductility as well as poor creep and corrosion performance. Understanding the impact of microstructural features on bulk response is key to improving Mg alloys for more widespread use and for moving towards truly predicting modeling capabilities. This study focuses on modeling the intrinsic features, particularly volume fraction and morphology of beta phase present, of cast Mg alloy microstructure and quantifying their impact on bulk performance. Computational results are compared to experimental measurements of cast plates of Mg alloy with varying aluminum content.

Cast Magnesium alloys↗

Ab initio calculations of the lattice parameter and elastic stiffness coefficients of bcc Fe with solutes

Here, we present an efficient methodology for computing solute-induced changes in lattice parameters and elastic stiffness coefficients Cij of single crystals using density functional theory. We also introduce a solute strain misfit tensor that quantifies how solutes change lattice parameters due to the stress they induce in the host crystal. Solutes modify the elastic stiffness coefficients through volumetric changes and by altering chemical bonds. We compute each of these contributions to the elastic stiffness coefficients separately, and verify that their sum agrees with changes in the elastic stiffness coefficients computed directly using fully optimized supercells containing solutes. Computing the two elastic stiffness contributions separately is more computationally efficient and provides more information on solute effects than the direct calculations. We compute the solute dependence of polycrystalline averaged shear and Young's moduli from the solute dependence of the single-crystal Cij. We then apply this methodology to substitutional Al, B, Cu, Mn, Si solutes and octahedral interstitial C and N solutes in bcc Fe. Comparison with experimental data indicates that our approach accurately predicts solute-induced changes in the lattice parameter and elastic coefficients. The computed data can be used to quantify solute-induced changes in mechanical properties such as strength and ductility, and can be incorporated into mesoscale models to improve their predictive capabilities.

36 MATERIALS SCIENCE↗

Effect of solutes on the lattice parameters and elastic stiffness coefficients of body-centered tetragonal Fe

In this study, we compute changes in the lattice parameters and elastic stiffness coefficients C ij of body-centered tetragonal (bct) Fe due to Al, B, C, Cu, Mn, Si, and N solutes. Solute strain misfit tensors determine changes in the lattice parameters as well as strain contributions to the changes in the C ij . We also compute chemical contributions to the changes in the C ij , and show that the sum of the strain and chemical contributions agree with more computationally expensive direct calculations that simultaneously incorporate both contributions. Octahedral interstitial solutes, with C being the most important addition in steels, must be present to stabilize the bct phase over the body-centered cubic phase. We therefore compute the effects of interactions between interstitial C solutes and substitutional solutes on the bct lattice parameters and C ij for all possible solute configurations in the dilute limit, and thermally average the results to obtain effective changes in properties due to each solute. Finally, the computed data can be used to estimate solute-induced changes in mechanical properties such as strength and ductility, and can be directly incorporated into mesoscale simulations of multiphase steels to model solute effects on the bct martensite phase.

36 MATERIALS SCIENCE↗

A finite element formulation for deformation twinning induced strain localization in polycrystal magnesium alloys

Deformation twinning induces shear strain localization in hexagonal close-packed crystals and is critical for the material’s ductility and failure. Cracks often occur at twin-twin or twin-grain boundary intersections and propagate along twin bands. However, most crystal plasticity models for deformation twinning are based on a “pseudo-slip” approach and do not capture the localized deformation associated with the formation of each discrete twin band. The few exceptions are discrete twin models that involve very complex numerical algorithms and are often compromised in accuracy due to the numerical convergence. These factors make the discrete twin models hard to adopt. This paper proposes a modification to the conventional finite element weak form, to fully incorporate a twin-induced heterogeneous deformation that does not depend on the “pseudo-slip” assumption. The model starts by splitting the deformation gradient into elastic-slip-twinning components. The twin-induced deformation gradient component is computed separately by solving a microstructural evolution problem and then implemented into finite element weak form by constructing a global “twin-force” vector. The constitutive update (e.g., in the user-defined material subroutine, or UMAT, for ABAQUS) therefore avoids dealing with the twinning and recovers to the form of a regular slip-based crystal plasticity model. The results presented here indicate that the twin-induced strain localization and the associated stress-reversal phenomena near the twin band were naturally captured in the model, which was validated against an in-situ synchrotron X-ray micro-diffraction experiment.

36 MATERIALS SCIENCE↗

Theoretical predictive screening of noble-metal-containing M 3 AuC 2 (M = Ti, V, and Cr) MAX phases

Using first-principles density functional theory (DFT), the ground state physical properties of the newly synthesized noble-metal-containing Ti 3 AuC 2 MAX phase have been investigated. The effect of transition-element Ti replacement (V and Cr) on physical properties, including structural, elastic, electronic, thermal, and optical are presented. The optimized lattice parameters of Ti 3 AuC 2 MAX phase are in good agreement with the experimental values and decrease when we replace Ti with V and then Cr. The magnetic properties of M 3 AuC 2 are predicted by using generalized gradient approximation (GGA) incorporating onsite electron correlation parameter (Hubbard U parameter) within DFT. Out of three studied MAX phases, V 3 AuC 2 and Cr 3 AuC 2 phases exhibit magnetism. The thermodynamical stability of M 3 AuC 2 (M = Ti, V, and Cr) phases is discussed by the formation enthalpy with respect to their most competing phases. The electronic structure reveals that these phases have metallic nature and are electrically anisotropic. The M-element replacement has an effect on the bonding properties of M 3 AuC 2 . The bonding between M-C is in the order of Cr 3 AuC 2 > V 3 AuC 2 > Ti 3 AuC 2 according to their peak positions and heights of density of states in the occupied site, which is also confirmed from the charge density distribution. The elastic properties indicate that M 3 AuC 2 phases are ductile, machinable, less stiff, and better resistant to thermal shock and are elastically anisotropic. To understand the properties of M 3 AuC 2 for the extreme environment, we employed a quasi-harmonic Debye model at the pressure and temperature range of 0–50 GPa and 0–1600 K, respectively. Additionally, we evaluated thermal conductivity and melting temperature to further understand the potential of these MAX phases in coating applications at elevated temperature. In relation to optical properties, these MAX phases have a reasonable absorption coefficient in the visible as well as in the ultra-violet regions. The reflectivity of M 3 AuC 2 phases is polarization dependent and of 45 % against the visible region, which reveals its potential as coating material to minimize solar heating.

312 MAX phases↗

A Gaussian Process-Based extended Goldak heat source model for finite element simulation of laser powder bed fusion additive manufacturing process

In this study, laser powder bed fusion (L-PBF) additive manufacturing (AM) is a key enabling technology to manufacture highly complex and integrated metallic structures. In L-PBF AM process, the melting of the metal powders and the layers underneath can be governed by either “conduction mode” or “keyhole mode”, with the keyhole mode reportedly leading to porosity and decreased strength and ductility by many studies. In part scale simulations, finite element (FE) model is often used to study the temperature distribution during printing and to predict the residual stress, where a volumetric heat flux with a Gaussian or a double ellipsoidal (Goldak) distribution is often applied as the laser heat source. However, the above heat source models can only capture the melt pool shape in the conduction mode, and fail to capture the transition to keyhole melting mode when the process parameters change. To overcome this inaccuracy, an extended Goldak heat source model is proposed by introducing a laser penetration term as a function of laser parameters obtained from a Gaussian-Process (GP) model. The model is validated by “2D pad” AlSi10Mg L-PBF experiments under a wide range of laser power, scan speed, and laser focus offset, and the results show the model successfully captures the measured melt pool shape in all conditions.

36 MATERIALS SCIENCE↗

Predicting fracture behavior in single crystal nickel using a coupled crystal plasticity phase field damage approach

Understanding the fracture behavior of single crystal metals is critical for predicting material performance under mechanical loading. Here, in this study, we investigate the fracture characteristics of single crystal nickel tensile bars using a crystal plasticity coupled phase field damage (CP-PFD) model. Experimental tensile tests were conducted on 15 specimens spanning five crystallographic orientations and three thickness variants per orientation. The results revealed two distinct fracture modes: brittle fractures with 45-degree angled surfaces and ductile fractures characterized by significant necking. The CP-PFD model successfully replicated these fracture behaviors, demonstrating strong agreement with experimental observations. The model effectively predicted the strain at which necking and fracture occurred, as well as the orientation-dependent fracture mechanisms. By comparing experimental and simulated fracture surfaces, we establish the CP-PFD model as a robust tool for predicting single crystal behavior and damage evolution. This work provides insight into the microstructural dependence of fracture behavior and establishes a predictive framework for modeling orientation-dependent damage evolution in single-crystal nickel.

Crystal plasticity↗