SEARCH · Engineering Papers

Results for “DIGESTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

All sources NASA NTRS DOE OSTI

DOE OSTI2013

Methane emissions from MBT landfills

Highlights: • Compilation of methane generation potential of mechanical biological treated (MBT) municipal solid waste. • Impacts and kinetics of landfill gas production of MBT landfills, approach with differentiated half-lives. • Methane oxidation in the waste itself and in soil covers. • Estimation of methane emissions from MBT landfills in Germany. - Abstract: Within the scope of an investigation for the German Federal Environment Agency (“Umweltbundesamt”), the basics for the estimation of the methane emissions from the landfilling of mechanically and biologically treated waste (MBT) were developed. For this purpose, topical research including monitoring results regarding the gas balance at MBT landfills was evaluated. For waste treated to the required German standards, a methane formation potential of approximately 18–24 m{sup 3} CH{sub 4}/t of total dry solids may be expected. Monitoring results from MBT landfills show that a three-phase model with differentiated half-lives describes the degradation kinetics in the best way. This is due to the fact that during the first years of disposal, the anaerobic degradation processes still proceed relatively intensively. In addition in the long term (decades), a residual gas production at a low level is still to be expected. Most of the soils used in recultivation layer systems at German landfills show a relatively high methane oxidation capacity up to 5 l CH{sub 4}/(m{sup 2} h). However, measurements at MBT disposal sites indicate that the majority of the landfill gas (in particular at non-covered areas), leaves the landfill body via preferred gas emission zones (hot spots) without significant methane oxidation. Therefore, rather low methane oxidation factors are recommended for open and temporarily covered MBT landfills. Higher methane oxidation rates can be achieved when the soil/recultivation layer is adequately designed and operated. Based on the elaborated default values, the First Order Decay (FOD) model of the IPCC Guidelines for National Greenhouse Gas Inventories, 2006, was used to estimate the methane emissions from MBT landfills. Due to the calculation made by the authors emissions in the range of 60,000–135,000 t CO{sub 2-eq.}/a for all German MBT landfills can be expected. This wide range shows the uncertainties when the here used procedure and the limited available data are applied. It is therefore necessary to generate more data in the future in order to calculate more precise methane emission rates from MBT landfills. This is important for the overall calculation of the climate gas production in Germany which is required once a year by the German Government.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2013

Experimental and life cycle assessment analysis of gas emission from mechanically–biologically pretreated waste in a landfill with energy recovery

Highlights: • Bio-methane landfill emissions from different period (0, 4, 8, 16 weeks) MTB waste have been evaluated. • Electrical energy recoverable from landfill gas ranges from 11 to about 90 kW h/tonne. • Correlation between oxygen uptake, energy recovery and anaerobic gas production shows R{sup 2} ranging from 0.78 to 0.98. • LCA demonstrate that global impact related to gaseous emissions achieve minimum for 4 week of MBT. - Abstract: The global gaseous emissions produced by landfilling the Mechanically Sorted Organic Fraction (MSOF) with different weeks of Mechanical Biological Treatment (MBT) was evaluated for an existing waste management system. One MBT facility and a landfill with internal combustion engines fuelled by the landfill gas for electrical energy production operate in the waste management system considered. An experimental apparatus was used to simulate 0, 4, 8 and 16 weeks of aerobic stabilization and the consequent biogas potential (Nl/kg) of a large sample of MSOF withdrawn from the full-scale MBT. Stabilization achieved by the waste was evaluated by dynamic oxygen uptake and fermentation tests. Good correlation coefficients (R{sup 2}), ranging from 0.7668 to 0.9772, were found between oxygen uptake, fermentation and anaerobic test values. On the basis of the results of several anaerobic tests, the methane production rate k (year{sup −1}) was evaluated. k ranged from 0.436 to 0.308 year{sup −1} and the bio-methane potential from 37 to 12 N m{sup 3}/tonne, respectively, for the MSOF with 0 and 16 weeks of treatment. Energy recovery from landfill gas ranged from about 11 to 90 kW h per tonne of disposed MSOF depending on the different scenario investigated. Life cycle analysis showed that the scenario with 0 weeks of pre-treatment has the highest weighted global impact even if opposite results were obtained with respect to the single impact criteria. MSOF pre-treatment periods longer than 4 weeks showed rather negligible variation in the global impact of system emissions.

09 BIOMASS FUELS↗

DOE OSTI2014

Non-biodegradable landfill leachate treatment by combined process of agitation, coagulation, SBR and filtration

Highlights: • A novel method of stripping (agitation) was investigated for NH{sub 3}-N removal. • PFS coagulation followed agitation process enhanced the leachate biodegradation. • Nitrification–denitrification achieved by changing operation process in SBR treatment. • A dual filter of carbon-sand is suitable as a polishing treatment of leachate. • Combined treatment success for the complete treatment of non-biodegradable leachate. - Abstract: This study describes the complete treatment of non-biodegradable landfill leachate by combined treatment processes. The processes consist of agitation as a novel stripping method used to overcome the ammonia toxicity regarding aerobic microorganisms. The NH{sub 3}-N removal ratio was 93.9% obtained at pH 11.5 and a gradient velocity (G) 150 s{sup −1} within a five-hour agitation time. By poly ferric sulphate (PFS) coagulation followed the agitation process; chemical oxygen demand (COD) and biological oxygen demand (BOD{sub 5}) were removed at 70.6% and 49.4%, respectively at an optimum dose of 1200 mg L{sup −1} at pH 5.0. The biodegradable ratio BOD{sub 5}/COD was improved from 0.18 to 0.31 during pretreatment step by agitation and PFS coagulation. Thereafter, the effluent was diluted with sewage at a different ratio before it was subjected to sequencing batch reactor (SBR) treatment. Up to 93.3% BOD{sub 5}, 95.5% COD and 98.1% NH{sub 3}-N removal were achieved by SBR operated under anoxic–aerobic–anoxic conditions. The filtration process was carried out using sand and carbon as a dual filter media as polishing process. The final effluent concentration of COD, BOD{sub 5}, suspended solid (SS), NH{sub 3}-N and total organic carbon (TOC) were 72.4 mg L{sup −1}, 22.8 mg L{sup −1}, 24.2 mg L{sup −1}, 18.4 mg L{sup −1} and 50.8 mg L{sup −1} respectively, which met the discharge standard. The results indicated that a combined process of agitation-coagulation-SBR and filtration effectively eliminated pollutant loading from landfill leachate.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2014

Oxygen demand for the stabilization of the organic fraction of municipal solid waste in passively aerated bioreactors

Highlights: • The use of an passively aerated reactor enables effective stabilization of OFMSW. • Convective air flow does not inhibit the aerobic stabilization of waste. • The use of an passively aerated reactor reduces the heat loss due to convection. • The volume of supplied air exceeds 1.7–2.88 times the microorganisms demand. - Abstract: Conventional aerobic waste treatment technologies require the use of aeration devices that actively transport air through the stabilized waste mass, which greatly increases operating costs. In addition, improperly operated active aeration systems, may have the adverse effect of cooling the stabilized biomass. Because active aeration can be a limiting factor for the stabilization process, passive aeration can be equally effective and less expensive. Unfortunately, there are few reports documenting the use of passive aeration systems in municipal waste stabilization. There have been doubts raised as to whether a passive aeration system provides enough oxygen to the organic matter mineralization processes. In this paper, the effectiveness of aeration during aerobic stabilization of four different organic fractions of municipal waste in a reactor with an integrated passive ventilation system and leachate recirculation was analyzed. For the study, four fractions separated by a rotary screen were chosen. Despite the high temperatures in the reactor, the air flow rate was below 0.016 m{sup 3}/h. Using Darcy’s equation, theoretical values of the air flow rate were estimated, depending on the intensity of microbial metabolism and the amount of oxygen required for the oxidation of organic compounds. Calculations showed that the volume of supplied air exceeded the microorganisms demand for oxidation and endogenous activity by 1.7–2.88-fold.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2014

Towards eliminating systematic errors caused by the experimental conditions in Biochemical Methane Potential (BMP) tests

Highlights: • The evaluated factors introduce significant systematic errors (10–38%) in BMP tests. • Ambient temperature (T) has the most substantial impact (∼10%) at low altitude. • Ambient pressure (p) has the most substantial impact (∼68%) at high altitude. • Continuous monitoring of T and p is not necessary for kinetic calculations. - Abstract: The Biochemical Methane Potential (BMP) test is increasingly recognised as a tool for selecting and pricing biomass material for production of biogas. However, the results for the same substrate often differ between laboratories and much work to standardise such tests is still needed. In the current study, the effects from four environmental factors (i.e. ambient temperature and pressure, water vapour content and initial gas composition of the reactor headspace) on the degradation kinetics and the determined methane potential were evaluated with a 2{sup 4} full factorial design. Four substrates, with different biodegradation profiles, were investigated and the ambient temperature was found to be the most significant contributor to errors in the methane potential. Concerning the kinetics of the process, the environmental factors’ impact on the calculated rate constants was negligible. The impact of the environmental factors on the kinetic parameters and methane potential from performing a BMP test at different geographical locations around the world was simulated by adjusting the data according to the ambient temperature and pressure of some chosen model sites. The largest effect on the methane potential was registered from tests performed at high altitudes due to a low ambient pressure. The results from this study illustrate the importance of considering the environmental factors’ influence on volumetric gas measurement in BMP tests. This is essential to achieve trustworthy and standardised results that can be used by researchers and end users from all over the world.

09 BIOMASS FUELS↗

DOE OSTI2015

Field assessment of semi-aerobic condition and the methane correction factor for the semi-aerobic landfills provided by IPCC guidelines

Highlights: • CH{sub 4}/CO{sub 2} and CH{sub 4} + CO{sub 2}% are proposed as indices to evaluate semi-aerobic landfills. • A landfill which CH{sub 4}/CO{sub 2} > 1.0 is difficult to be categorized as semi-aerobic landfill. • Field conditions should be carefully investigated to determine landfill types. • The MCF default value for semi-aerobic landfills underestimates the methane emissions. - Abstract: According to IPCC guidelines, a semi-aerobic landfill site produces one-half of the amount of CH{sub 4} produced by an equally-sized anaerobic landfill site. Therefore categorizing the landfill type is important on greenhouse gas inventories. In order to assess semi-aerobic condition in the sites and the MCF value for semi-aerobic landfill, landfill gas has been measured from vent pipes in five semi-aerobically designed landfills in South Korea. All of the five sites satisfied requirements of semi-aerobic landfills in 2006 IPCC guidelines. However, the ends of leachate collection pipes which are main entrance of air in the semi-aerobic landfill were closed in all five sites. The CH{sub 4}/CO{sub 2} ratio in landfill gas, indicator of aerobic and anaerobic decomposition, ranged from 1.08 to 1.46 which is higher than the values (0.3–1.0) reported for semi-aerobic landfill sites and is rather close to those (1.0–2.0) for anaerobic landfill sites. The low CH{sub 4} + CO{sub 2}% in landfill gas implied air intrusion into the landfill. However, there was no evidence that air intrusion has caused by semi-aerobic design and operation. Therefore, the landfills investigated in this study are difficult to be classified as semi-aerobic landfills. Also MCF of 0.5 may significantly underestimate methane emissions compared to other researches. According to the carbon mass balance analyses, the higher MCF needs to be proposed for semi-aerobic landfills. Consequently, methane emission estimate should be based on field evaluation for the semi-aerobically designed landfills.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2015

Converting campus waste into renewable energy – A case study for the University of Cincinnati

Highlights: • A case study to show the benefits of waste-to-energy projects at a university. • Evaluated the technical and economic feasibilities as well as GHG reduction. • A tool for other universities/communities to evaluate waste-to-energy projects. - Abstract: This paper evaluates the implementation of three waste-to-energy projects at the University of Cincinnati: waste cooking oil-to-biodiesel, waste paper-to-fuel pellets and food waste-to-biogas, respectively. The implementation of these waste-to-energy (WTE) projects would lead to the improvement of campus sustainability by minimizing waste management efforts and reducing GHG emissions via the displacement of fossil fuel usage. Technical and economic aspects of their implementation were assessed and the corresponding GHG reduction was estimated. Results showed that on-site implementation of these projects would: (1) divert 3682 L (974 gallons) of waste cooking oil to 3712 L (982 gallons) of biodiesel; (2) produce 138 tonnes of fuel pellets from 133 tonnes of waste paper (with the addition of 20.75 tonnes of plastics) to replace121 tonnes of coal; and (3) produce biogas that would be enough to replace 12,767 m{sup 3} natural gas every year from 146 tonnes of food waste. The economic analysis determined that the payback periods for the three projects would be 16 months for the biodiesel, 155 months for the fuel pellet, and 74 months for the biogas projects. The reduction of GHG emission from the implementation of the three WTE projects was determined to be 9.37 (biodiesel), 260.49 (fuel pellets), and 11.36 (biogas) tonnes of CO{sub 2}-eq per year, respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2015

A comparative study of leachate quality and biogas generation in simulated anaerobic and hybrid bioreactors

Highlights: • Temporary aeration shortened the initial acid inhibition phase for methanogens. • COD decreased faster in the hybrid bioreactor than that in the anaerobic control. • Methane generations from hybrid bioreactors were 133.4 L/kg{sub vs} and 113.2 L/kg{sub vs}. • MSW settlement increased with increasing the frequency of intermittent aeration. - Abstract: Research has been conducted to compare leachate characterization and biogas generation in simulated anaerobic and hybrid bioreactor landfills with typical Chinese municipal solid waste (MSW). Three laboratory-scale reactors, an anaerobic (A1) and two hybrid bioreactors (C1 and C2), were constructed and operated for about 10 months. The hybrid bioreactors were operated in an aerobic–anaerobic mode with different aeration frequencies by providing air into the upper layer of waste. Results showed that the temporary aeration into the upper layer aided methane generation by shortening the initial acidogenic phase because of volatile fatty acids (VFAs) reduction and pH increase. Chemical oxygen demand (COD) decreased faster in the hybrid bioreactors, but the concentrations of ammonia–nitrogen in the hybrid bioreactors were greater than those in the anaerobic control. Methanogenic conditions were established within 75 d and 60 d in C1 and C2, respectively. However, high aeration frequency led to the consumption of organic matters by aerobic degradation and resulted in reducing accumulative methane volume. The temporary aeration enhanced waste settlement and the settlement increased with increasing the frequency of aeration. Methane production was inhibited in the anaerobic control; however, the total methane generations from hybrid bioreactors were 133.4 L/kg{sub vs} and 113.2 L/kg{sub vs}. As for MSW with high content of food waste, leachate recirculation right after aeration stopped was not recommended due to VFA inhibition for methanogens.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2015

The decay of wood in landfills in contrasting climates in Australia

Highlights: • We examine decay in wood from landfills in contrasting environments in Australia. • Analysis is based on changes in chemical composition and microscopy. • Climate did not influence levels of decay observed. • Microscopy of retrieved samples revealed most of the decay was aerobic in nature. • Current default factors for wood decay in landfills overestimate methane emissions. - Abstract: Wood products in landfill are commonly assumed to decay within several decades, returning the carbon contained therein to the atmosphere, with about half the carbon released as methane. However, the rate and extent of decay is not well known, as very few studies have examined the decay of wood products in landfills. This study reports on the findings from landfill excavations conducted in the Australian cities of Sydney and Cairns located in temperate and tropical environments, respectively. The objective of this study was to determine whether burial of the wood in warmer, more tropical conditions in Cairns would result in greater levels of decay than occurs in the temperate environment of Sydney. Wood samples recovered after 16–44 years in landfill were examined through physical, chemical and microscopic analyses, and compared with control samples to determine the carbon loss. There was typically little or no decay in the wood samples analysed from the landfill in Sydney. Although there was significant decay in rainforest wood species excavated from Cairns, decay levels for wood types that were common to both Cairns and Sydney landfills were similar. The current Intergovernmental Panel on Climate Change (IPCC, 2006) default decay factor for organic materials in landfills is 50%. In contrast, the carbon loss determined for Pinus radiata recovered from Sydney and Cairns landfills was 7.9% and 4.4%, respectively, and 0% for Agathis sp. This suggests that climate did not influence decay, and that the more extensive levels of decay observed for some wood samples from Cairns indicates that those wood types were more susceptible to biodegradation. Microscopic analyses revealed that most decay patterns observed in samples analysed from Sydney were consistent with aerobic fungal decay. Only a minor portion of the microbial decay was due to erosion bacteria active in anaerobic/near anaerobic environments. The findings of this study strongly suggest that models that adopt current accepted default factors for the decay of wood in landfills greatly overestimate methane emissions.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2018

Influence of chemical composition on biochemical methane potential of fruit and vegetable waste

Highlights: • Different mixtures of fruit and vegetable waste collected along one year were analysed. • Chemical composition showed great variation over time. • BMP ranged from 288 to 516 L{sub N} CH{sub 4} kg VS{sup −1} with 79% biodegradability average. • Lipid and high calorific value is well correlated to BMP. • Multiple regression models show good ability to predict methane potential. - Abstract: This study investigates the influence of chemical composition on the biochemical methane potential (BMP) of twelve different batches of fruit and vegetable waste (FVW) with different compositions collected over one year. BMP ranged from 288 to 516 L{sub N} CH{sub 4} kg VS{sup −1}, with significant statistical differences between means, which was explained by variations in the chemical composition over time. BMP was most strongly correlated to lipid content and high calorific values. Multiple linear regression was performed to develop statistical models to more rapidly predict methane potential. Models were analysed that considered chemical compounds and that considered only high calorific value as a single parameter. The best BMP prediction was obtained using the statistical model that included lipid, protein, cellulose, lignin, and high calorific value (HCV), with R{sup 2} of 92.5%; lignin was negatively correlated to methane production. Because HCV and lipids are strongly correlated, and because HCV can be determined more rapidly than overall chemical composition, HCV may be useful for predicting BMP.

09 BIOMASS FUELS↗

DOE OSTI2018

Comparison of the acidogenic and methanogenic potential of agroindustrial residues

Highlights: • Mixed acidogenic fermentation shows lower yields but higher product value than methanogenesis. • VFA concentrations reported are among the highest in literature for batch acidogenic fermentation. • Trub is an attractive residue for valorisation due to the potential for caproic acid production. • Brewery residues have a significant economic potential. - Abstract: The methanogenic and acidogenic potentials of six different agroindustrial residues, i.e. of fruit pulps and brewery residues, were determined. For all substrates, the methanogenic conversion yield was systematically higher than the acidogenic one in Chemical Oxygen Demand (COD) terms, ranging from 0.46 to 0.87 g{sub COD{sub CH4}}/{sub gCOD{sub substrate{sub fed}}} and from 0.24 to 0.56 g{sub COD{sub tVFA}}/g{sub COD{sub substrate{sub fed}}}, respectively. During methanogenic conversion, brewery trub exhibited the highest methane potential (304 ml{sub CH4}/g{sub COD{sub substrate}}). Trub also exhibited the highest total volatile fatty acids (tVFA) concentrations in the mixed liquor (ML) during acidogenic conversion (29.7 g{sub COD{sub tVFA}}/kg{sub ML}). Acetic, butyric and caproic acids were the main carboxylates produced by the different substrates. Despite the lower conversion yields, the economic value of the acidogenic product (carboxylate streams) is higher than that of methanogenic conversion (methane) due to the higher value of carboxylates and their potential use in finer applications (e.g. bio-based products) compared to energy production form methane.

09 BIOMASS FUELS↗

DOE OSTI2015

Exocrine pancreas ER stress is differentially induced by different fatty acids

Exocrine pancreas acinar cells have a highly developed endoplasmic reticulum (ER), accommodating their high protein production rate. Overload of dietary fat (typical to obesity) is a recognized risk factor in pancreatitis and pancreatic cancer. Dietary fat, especially saturated fat, has been suggested by others and us to induce an acinar lipotoxic effect. The effect of different dietary fatty acids on the ER stress response is unknown. We studied the effect of acute (24 h) challenge with different fatty acids (saturated, mono and poly-unsaturated) at different concentrations (between 200 and 500 µM, typical to normal and obese states, respectively), testing fat accumulation, ER stress indicators, X-box binding protein 1 (Xbp1) splicing and nuclear translocation, as well as unfolded protein response (UPR) transcripts and protein levels using exocrine pancreas acinar AR42J and primary cells. Acute exposure of AR42J cells to different fatty acids caused increased accumulation of triglycerides, dependent on the type of fat. Different FAs had different effects on ER stress: most notably, saturated palmitic acid significantly affected the UPR response, as demonstrated by altered Xbp1 splicing, elevation in transcript levels of UPR (Xbp, CHOP, Bip) and immune factors (Tnfα, Tgfβ), and enhanced Xbp1 protein levels and Xbp1 time-dependent nuclear translocation. Poly-unsaturated FAs caused milder elevation of ER stress markers, while mono-unsaturated oleic acid attenuated the ER stress response. Thus, various fatty acids differentially affect acinar cell fat accumulation and, apart from oleic acid, induce ER stress. The differential effect of the various fatty acids could have potential nutritional and therapeutic implications. - Highlights: • Exocrine pancreas acinar cells have a highly developed endoplasmic reticulum (ER) and thus highly susceptible to ER stress. • We studied the effect of acute challenge with different fatty acids and doses typical to normal and obese states on ER stress. • Saturated palmitic acid significantly affected the ER UPR response demonstrated by; altered Xbp1 splicing, elevation in UPR transcripts levels and immune factors, Xbp1 protein level and Xbp1 time-depended nucleus translocation. • Poly and monounsaturated fatty acids demonstrated varying effects on ER stress markers. • Oleic acid demonstrate protective effect on pancreatic ER stress.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2017

Pancreatic stellate cell activation is regulated by fatty acids and ER stress

Introduction: Pancreatic pathologies are characterized by a progressive fibrosis process. Pancreatic stellate cells (PSC) play a crucial role in pancreatic fibrogenesis. Endoplasmic reticulum (ER) stress emerges as an important determinant of fibrotic remodeling. Overload of fatty acids (FA), typical to obesity, may lead to lipotoxic state and cellular stress. Aim: To study the effect of different lipolytic challenges on pancreatic ER stress and PSC activation. Methods: Primary PSCs were exposed to different FAs, palmitate (pal) and oleate (ole), at pathophysiological concentrations typical to obese state, and in acute caerulein-induced stress (cer). PSC activation and differentiation were analyzed by measuring fat accumulation (oil-red staining and quantitation), proliferation (cells count) and migration (wound- healing assay). PSC differentiation markers (α-sma, fibronectin, tgf-β and collagen secretion), ER stress unfolded protein response and immune indicators (Xbp1, CHOP, TNF-α, IL-6) were analyzed at the transcript and protein expression levels (quantitative RT-PCR and western blotting). Results: PSC exposure to pal and ole FAs (500 µM) increased significantly fat accumulation. Proliferation and migration analysis demonstrated that ole FA retained PSC activation, while exposure to pal FA significantly halted proliferation rate and delayed migration. Cer significantly augmented PSC differentiation markers α- sma, fibronectin and collagen, and ER stress and inflammation markers including Xbp1, CHOP, TNF-α and IL-6. The ole FA treatment significantly elevated PSC differentiation markers α-sma, fibronectin and collagen secretion. PSC ER stress was demonstrated following pal treatment with significant elevation of Xbp1 splicing and CHOP levels. Conclusion: Exposure to pal FA halted PSC activation and differentiation and elevated ER stress markers, while cer and ole exposure significantly induced activation, differentiation and fibrosis. Thus, dietary FA composition should be considered and optimized to regulate PSC activation and differentiation in pancreatic pathologies. - Highlights: • Pancreatic stellate cells (PSC) play a crucial role in pancreatic fibrogenesis. • Endoplasmic reticulum (ER) stress is an important determinant of fibrotic remodeling. • Overload of fatty acids, typical to obesity, may lead to lipotoxicity and cellular stress. • Exposure to pal FA halts PSC activation, differentiation and elevated ER stress. • Cer and ole exposure significantly induced activation, differentiation and fibrosis.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2017

The zinc finger protein CG12744 is essential for differentiation and regeneration after infection in the adult Drosophila midgut

Highlights: • CG12744 promotes EC differentiation by regulating Osa and JNK levels after infection. • CG12744 suppresses EE differentiation after infection. • CG12744 regulates the maintenance of epithelial architecture after infection. Pluripotent stem cell activity is essential to maintain regeneration and homeostasis in the Drosophila midgut following environmental challenges. Although multiple pathways have been implicated in epithelial renewal, the underlying regulatory mechanisms and correlations between relevant genes and pathways remain elusive. In this study, we show that the zinc finger protein CG12744 plays an important role in the differentiation and regeneration of epithelial cells in response to oral infection with Erwinia carotovora carotovora 15. Knocking down CG12744 in enteroblasts decreased the post-infection proportion of enteroblasts and enterocytes and increased the post-infection number of enteroendocrine cells. In addition, in precursors, CG12744 affected the Osa, jun-N-terminal kinase and bone morphogenetic protein signaling pathways to control enterocyte differentiation. Finally, CG12744 maintained epithelial architecture and cell fate in enterocytes following an acute infectious challenge.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

Role of NLR family pyrin domain-containing 3 inflammasome in the activation of pancreatic stellate cells

Highlights: • NLRP3 inflammasome was activated with the extension of activation time of PSCs. • LPS triggered PSCs activation through activating NLRP3 Inflammasome. • Inhibition of NLRP3 inflammasome mitigates the activation of PSCs. • NLRP3 inflammasome activates the TGF-β1/Smad3 signaling pathway in PSCs. NLRP3 inflammasome activation plays an important role in the development of pancreatic fibrosis. However, it is unclear whether the activation of the NLRP3 inflammasome is directly involved in the activation of Pancreatic stellate cells (PSCs). The aim of this study was to investigate the role and mechanism of the NLRP3 inflammasome in the activation of PSCs. In vivo, a rat model of chronic pancreatitis (CP) was induced by intravenous injection of dibutyltin dichloride (DBTC). In vitro, rat primary PSCs were isolated from pancreatic tissues and incubated with the NLRP3 inflammasome activator LPS, the NLRP3 inhibitor MCC950, or NLRP3 siRNA. The results showed that the expression of NLRP3, pro-Caspase-1, Caspase-1 and IL-18 was increased in the rat model of CP and during PSCs activation. LPS increased the protein levels of NLRP3, ASC, Caspase-1, IL-1β and IL-18 accompanied by the upregulation of α-SMA, Col I and FN expression. Moreover, MCC950 or NLPR3 siRNA decreased the expression of α-SMA, Col I, FN, TGF-β1 and p-Smad3. Furthermore, MCC950 reversed the LPS-induced upregulation of α-SMA, FN and Col Ⅰ expression in PSCs. This study revealed that the NLRP3 inflammasome is directly involved in the activation of PSCs in vivo and in vitro. Inhibiting NLRP3 suppresses the activation of PSCs through the TGF-β1/Smad3 pathway.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2025

Continuous Wet Air Oxidation of the Hydrothermal Liquefaction Aqueous Product from Various Wet Wastes

Wet air oxidation (WAO) offers an effective method for treating waste streams, converting pollutants into benign substances, and holds significant potential for processing the aqueous product from the hydrothermal liquefaction (HTL-AP) of wet wastes, a promising renewable fuel technology. Here, we conducted a comprehensive study of the WAO of HTL-AP from four different wet wastes. Through continuous testing under various conditions, we produced samples with different chemical oxygen demand (COD) levels, enhancing understanding of reaction parameters necessary for substantial COD reduction (>95%). Chemical analysis revealed that alcohols and ketones in the HTL-AP rapidly oxidized to acetic acid through aldehyde intermediates, while acetic acid, other carboxylic acids, and phenols oxidized relatively slowly. The light N-containing compounds were found to exhibit a change in concentration only after the whole sample reaches an 80% COD reduction, indicating their refractory nature under applied conditions. Energy released in the WAO reaction was calculated, and anaerobic toxicity assay demonstrated that WAO treatment enhanced methane production kinetics due to reduced inhibitory effects, suggesting partial oxidative transformation of inhibitory compounds into less toxic derivatives. These findings provide insights into designing effective WAO processes for valorizing HTL aqueous products, addressing key barriers to HTL process commercialization.

anaerobic digestion↗

DOE OSTI2011

Coherent Synchrotron-Based Micro-Imaging Employed for Studies of Micro-Gap Formation in Dental Implants

Biocompatible materials such as titanium are regularly applied in oral surgery. Titanium-based implants for the replacement of missing teeth demand a high mechanical precision in order to minimize micro-bacterial leakage, especially when two-piece concepts are used. Synchrotron-based hard x-ray radiography, unlike conventional laboratory radiography, allows high spatial resolution in combination with high contrast even when micro-sized features in such highly attenuating objects are visualized. Therefore, micro-gap formation at interfaces in two-piece dental implants with the sample under different mechanical loads can be studied. We show the existence of micro-gaps in implants with conical connections and study the mechanical behavior of the mating zone of conical implants during loading. The micro-gap is a potential source of implant failure, i.e., bacterial leakage, which can be a stimulus for an inflammatory process.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2022

Identification of excited states in Bi 188 and Po 188

The neutron-deficient 188 Bi and 188 Po isotopes have been studied by γ-ray spectroscopy using the recoil-decay tagging technique with the Argonne Gas-Filled Analyzer. A new 0.25(5)-μs isomeric state and a prompt cascade formed by 319-, 366-, and 462-keV γ rays have been established on top of the (10¯) α -decaying isomer in 188 Bi. The first excited (2 + ) state in 188 Po was identified, its excitation energy of 242(2) keV continues the nearly constant trend for the first 2 + states in 190, 192,194 Po. Here, the state is most likely a member of a prolate rotational band built on the ground state, albeit mixing with other coexisting configurations cannot be excluded. The new results obtained in the present work provide new information to shape coexistence in bismuth and polonium isotopes near the neutron midshell at N = 104 . In this mass region, a reduction in the prompt γ-ray yield obtained with recoil decay tagging was observed for a few nuclides, and the possible reasons are presented.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗