Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Concentrated Solar”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Seasonal behavior of NO2 in the winter stratosphere - Inferred NO(x)

An analysis is performed of Solar Mesosphere Explorer (SME) data for the first 90 days of 1982, when a trend of increasing NO2 content in the stratosphere near the 10 mbar pressure level was detected. A photochemical-dynamical model is developed to account for the observed densities, which were also detected with ground-based instrumentation. The model calculations indicated that partitioning of the NO(x) family from N2O5 to NO2 was responsible for the trend. The new partitioning requires a lowering of the mixing ratio of NO(x), which was also observed. Finally, the SME data also confirmed that the enhanced NO2 concentrations were dependent on the solar zenith angle.

Zawodny, J. M.↗

Silicon materials task of the Low Cost Solar Array Project: Effect of impurities and processing on silicon solar cells

The effects of impurities and processing on the characteristics of silicon and terrestrial silicon solar cells were defined in order to develop cost benefit relationships for the use of cheaper, less pure solar grades of silicon. The amount of concentrations of commonly encountered impurities that can be tolerated in typical p or n base solar cells was established, then a preliminary analytical model from which the cell performance could be projected depending on the kinds and amounts of contaminants in the silicon base material was developed. The impurity data base was expanded to include construction materials, and the impurity performace model was refined to account for additional effects such as base resistivity, grain boundary interactions, thermal processing, synergic behavior, and nonuniform impurity distributions. A preliminary assessment of long term (aging) behavior of impurities was also undertaken.

Hopkins, R. H.↗

Plasmon-Enhanced Greenhouse Selectivity for High-Temperature Solar Thermal Energy Conversion

The greenhouse effect arises when thermal radiation is forced to undergo absorption and re-emission many times before escaping, while sunlight transmits largely unimpeded. Although this effect is responsible for global warming, it is generally weak in solid-state materials because radiation can be easily overpowered by other modes of heat transfer. Here, we report on the use of infrared plasmonic nanoparticles to enhance the greenhouse effect in transparent mesoporous materials. Local surface plasmon resonances in transparent conducting oxide nanoparticles (TCO NPs) selectively shorten the mean free path of thermal photons while maintaining high solar transmittance. The addition of a small amount of TCO NPs (<0.1% by volume) nearly halves the heat losses at 700 °C. This leads to an experimentally demonstrated effective thermal emittance of ~0.17 at 700 °C, which is the lowest reported value to date, among all selective surfaces and transparent insulating materials measured at 650 °C or above. Furthermore, our results show that plasmon-enhanced greenhouse selectivity (PEGS) is a promising mechanism for spectral control of radiative heat transfer, and more specifically, for conversion of minimally concentrated sunlight into high-temperature heat.

14 SOLAR ENERGY↗

Radiation damage and defect behavior in proton irradiated lithium-counterdoped n+p silicon solar cells

Two lithium-counterdoped n+p silicon solar cells with different lithium concentrations were irradiated by 10-MeV protons. Cell performance was measured as a function of fluence, and it was found that the cell with the highest concentration of lithium had the highest radiation resistance. Deep level transient spectroscopy which showed two deep level defects that were lithium related. Relating the defect energy levels obtained from this study with those from earlier work using 1-MeV electron irradiation shows no correlation of the defect energy levels. There is one marked similarity: the absence of the boron-interstitial-oxygen-interstitial defect. This consistency strengthens the belief that lithium interacts with oxygen to prevent the formation of the boron interstitial-oxygen interstitial defect. The results indicate that, in general, addition of lithium in small amounts to the p-base of a boron doped silicon solar cell such that the base remains p-type, tends to increase the radiation resistance of the cell.

Stupica, John↗

Solar Irradiation Induced Transformation of Ferrihydrite in the Presence of Aqueous Fe 2+

Ferrihydrite commonly occurs in soils and sediments, especially in acid mine drainage (AMD). Solar irradiation may affect Fe(II)-catalyzed transformation of metastable ferrihydrite to more stable iron oxides on AMD surface. We investigated the Fe(II)-catalyzed transformation process and mechanism of ferrihydrite under light irradiation. In nitrogen atmosphere, Fe 2+ aq could be oxidized to goethite and lepidocrocite by hydroxyl radical (OH • ), superoxide radical (O 2 •– ) and hole (h vb + ) generated from ferrihydrite under ultraviolet (UV) irradiation (300–400 nm) at pH 6.0, and O 2 •– and h vb + were mainly responsible for Fe 2+ aq oxidation. In addition, the ligand-to-metal charge-transfer (LMCT) process between Fe(II) and ferrihydrite could be promoted by UV irradiation. Goethite proportion increased with increasing Fe 2+ aq concentration. Both visible (vis) and solar irradiation could also lead to the oxidation of Fe 2+ aq to goethite and lepidocrocite, and the proportion of lepidocrocite increased with increasing light intensity. Fe 2+ aq was photochemically oxidized to schwertmannite at pH 3.0 and 4.5, and the oxidation rate was higher than that under dark conditions in air. The photochemical oxidation rate of Fe 2+ aq decreased in the presence of humic acid. This study facilitates a better understanding of the formation and transformation of iron oxides in natural environments and ancient Earth.

54 ENVIRONMENTAL SCIENCES↗

Performance Analyses of Supercritical Carbon Dioxide-Based Parabolic Trough Collectors with Double-Glazed Receivers

Supercritical carbon dioxide is becoming a hot research topic as a potential heat transfer fluid in parabolic trough concentrators since it enables operating the solar system at high temperatures for a higher quality of energy. However, the corresponding inflated thermal losses necessitate alternative receiver designs. This work examines four double-glazed receivers, with each annular space being evacuated or non-evacuated, in terms of the absorber tube's diameter (53-80 mm) and the diameter ratios of the two glass shells (1.2-2.0). An analytical model is developed and validated for this purpose, and the four designs are further examined using ground-level solar and meteorological measurements. The results demonstrate higher performance in the case of fully evacuating the receiver and using the smallest possible diameters of the three concentric cylinders, where the energy and exergy efficiencies reach 65.3 and 40.3%, respectively. Yet, evacuating only the inner annular space is sufficient to achieve virtually the same performance level. This energy efficiency decreases to 62% in case of increasing the tube diameter to 80 mm. As the operating temperature increases from 423 to 850 K, the specific thermal losses increase by 3.98-4.34 folds, depending on the receiver design. Double glazing the receivers is favorable only at high operating temperatures of sCO2, where the reduction in thermal losses overcomes the drop in optical efficiency. For an inlet sCO2 temperature of 850 K, thermal losses are reduced by 33.64 and 53.92%, compared to evacuated and non-evacuated single-glazed receivers, respectively. Throughout the year, the fully evacuated and fully non-evacuated double-glazed receivers have energy efficiencies of 54.96 and 52.39%, exergy efficiencies of 33.64 and 32.06%, and thermal losses of 348.8 and 402.5 W/m, respectively.

analytical model↗

On-Sun Characterization of Microchannel Supercritical Carbon Dioxide Solar Thermal Receivers - Preliminary Findings

The design of, and preliminary on-sun tests on, an 8 cm x 8 cm microchannel supercritical carbon dioxide (sCO2) receiver is presented. The receiver has a laminated design, wherein sheets of Haynes 230 nickel superalloy are patterned and diffusion bonded to form microscale flow passages. The microscale pattern is in the form of square pins with width and height of 500 μm and 200 μm respectively. The pins are arranged in an in-line pattern with respect to the flow direction. The longitudinal and transverse pitch ratios of the micro pin fins are identical and equal to two times the side width of the pillar. A sCO2 test facility is developed with the ability to supply sCO2 at 200 bar pressure and at temperatures between 300-500°C to the receiver inlet. The sCO2 facility is coupled to a seven meter diameter parabolic dish with a 25 kW rating and a concentration ratio of about 800. On-sun tests are performed at a receiver inlet pressure of 150 bar and a receiver inlet temperature between 110-130°C. Receiver and thermal efficiencies in excess of 0.91 and 0.96 respectively for the incident heat flux ranging from 8 to 80 W/cm2, and average surface temperatures ranging from 150-550°C are obtained in these experiments.

14 SOLAR ENERGY↗

The Shenandoah concentrator

A 7 meter diameter, parabolic dish solar collector was designed and developed for first application at Shenandoah, Georgia. Key features and requirements for the collector are outlined. Performance test results for collector testing at Sandia Laboratories in Albuquerque are summarized. The key features, requirements and performance of the solar collector subassemblies/subsystems are discussed: mount and drives, reflector, receiver, and collector control unit. Problems experienced during collector testing in Albuquerque are identified and solutions described.

Poche, A. J.↗

Effects of processing on the carrier lifetime in silicon solar cells

Measurements were taken to determine the effects that solar cell processing steps have on the minority carrier lifetime in silicon. The experimental work included measurements of diffusion lengths of the silicon at various stages of cell fabrication, of solar cell properties, and of the PN junction properties for ingots covering a wide range of doping and other ingot properties. Resistivities covered the range of 0.01 to 10 ohm-cm, and combinations of extreme concentrations (high and low) of dislocations and oxygen were included. The results showed that the major cell process steps did not usually cause any appreciable change in diffusion lengths. The solar cell currents obtained supported the diffusion length measurements. The effects of heavy doping concentrations on solar cell performance were studied. Attempts were made to relate the voltage behavior of the cells with the diode properties and the properties of the ingots.

Iles, P. A.↗

Estimates of Sputter Yields of Solar-Wind Heavy Ions of Lunar Regolith Materials

At energies of approximately 1 keV/amu, solar-wind protons and heavy ions interact with the lunar surface materials via a number of microscopic interactions that include sputtering. Solar-wind induced sputtering is a main mechanism by which the composition of the topmost layers of the lunar surface can change, dynamically and preferentially. This work concentrates on sputtering induced by solar-wind heavy ions. Sputtering associated with slow (speeds the electrons speed in its first Bohr orbit) and highly charged ions are known to include both kinetic and potential sputtering. Potential sputtering enjoys some unique characteristics that makes it of special interest to lunar science and exploration. Unlike the yield from kinetic sputtering where simulation and approximation schemes exist, the yield from potential sputtering is not as easy to estimate. This work will present a preliminary numerical scheme designed to estimate potential sputtering yields from reactions relevant to this aspect of solar-wind lunar-surface coupling.

Barghouty, Abdulmasser F.↗

Intershock observations during STIP intervals 17 and 18

The Prognoz-10/Intercosmos satellite (Intershock Project) carried out observations from Earth orbit from 26 April 1985 until 11 November 1985, covering STIP Intervals XVII and XVIII. Data obtained during the systematic measurements in the course of STIP Interval XVII and part of XVIII are presented; i.e., hourly averages of the solar wind velocity, temperature and ion concentration, ion flux changes (10 to the -1 to 10 to the -3 Hz), plasma wave parameters, energetic particles flux, magnetic fields, etc. Special attention is paid to solar wind distrubances causing abrupt and large effects on the shape of the bow shock (i.e., on 2 May 1985 and 14 September 1985). Generally, the observation period was very close to a minimum of solar activity and was quiet without significant interplanetary shocks.

Zastenker, G.↗

The structure of photospheric flux tubes

Basic physical mechanisms for producing the observed intense magnetic flux tubes in the solar photosphere are reviewed. The mechanism of flux expulsion by convective cells can concentrate magnetic flux up to the equipartition field strength, which is only about 200 G at the solar surface for the observed granular convection. Other mechanisms that partially evacuate the flux tube are needed to produce further concentration of magnetic flux to the observed values of 1000-1500 G. Two such mechanisms are discussed: concentration by convective collapse of a vertical flux tube in the superadiabatic layer just below the solar surface, and concentration by a siphon flow in an arched, isolated flux tube.

Thomas, John H.↗

Detection of stopped solar flare helium in lunar rock 68815

Steep increases were detected in the concentration profiles of He-3 and possibly of Ne-21 in the near-surface layers of lunar rock 68815, which was exposed on the lunar surface for 2 Myr. The concentration profile of He-3 is inconsistent with either spallation or solar wind components, but it agrees with expected ranges of stopped solar flare particles. Although the He-3 retention in this rock is determined to be very low (approximately 3% at the surface), a long-term average solar flare ratio He-4/He-3 can be estimated at 12 to within a factor of about 3. This ratio is two orders of magnitude smaller than the same ratio observed in the solar wind, but it is consistent with solar flare data from recent satellite observations.

Yaniv, A.↗

Recent developments in low cost silicon solar cells for terrestrial applications

A variety of techniques may be used for photovoltaic energy systems. Concentrated or not concentrated sunlight may be employed, and a number of materials can be used, including silicon, gallium arsenide, cadmium sulfide, and cadmium telluride. Most of the experience, however, has been obtained with silicon cells employed without sunlight concentration. An industrial base exists at present for producing solar cells at a price in the range from $15 to $30 per peak watt. A major federal program has the objective to reduce the price of power provided by silicon solar systems to approximately $1 per peak watt in the early 1980's and $0.50 per watt by 1986. The approaches considered for achieving this objective are discussed.

Leipold, M. H.↗

Topographic Correction of Optical Remote Sensing Images in Mountainous Areas: A systematic review

Rugged terrain distorts optical remote sensing observations and subsequently impacts land cover classification and biophysical and biochemical parameter retrieval over mountainous areas. Therefore, topographic correction (TC) is a prerequisite for many remote sensing applications. Although various TC methods have been explored over the past four decades to mitigate topographic effects, a systematic and global review of these studies is still lacking. Using a multicomponent bibliometric approach, we extracted bibliometric metadata from 426 publications identified by searching titles, keywords, and abstracts for research on “topographic correction” and “topographic effects” in Scopus and Web of Science (WoS) from 1980 to 2022. Here this systematic review revealed a rapid growth in the number of TC studies since the 1980s, primarily driven by the availability of decametric-resolution remote sensing observations and digital elevation models (DEMs). Most of the research has focused on relatively low-elevation regions, with increasing attention beyond American and European regions, particularly in China. The seasonal distribution of satellite acquisition for TC showed considerable imbalance, mainly concentrated in months with favorable solar illumination conditions (e.g., May to October). Important themes emerged from the keyword analysis, including satellite sensors, DEMs, TC methods, evaluation criteria, and applications.

58 GEOSCIENCES↗

The Escape Velocity Profile of the Milky Way from Gaia DR3

Abstract The escape velocity profile of the Milky Way offers a crucial and independent measurement of its underlying mass distribution and dark matter (DM) properties. Using a sample of stars from the third data release of Gaia with 6D kinematics and strict quality cuts, we obtain an escape velocity profile of the Milky Way from 4 to 11 kpc in Galactocentric radius. To infer the escape velocity in radial bins, we model the tail of the stellar speed distribution with both traditional power-law models and a new functional form that we introduce. While power-law models tend to rely on extrapolation to high speeds, we find our new functional form gives the most faithful representation of the observed distribution. Using this for the escape velocity profile, we constrain the properties of the Milky Way’s DM halo modeled as a Navarro–Frenck–White profile. Combined with constraints from the circular velocity at the solar position, we obtain a concentration and mass of c 200 c DM = 13.9 − 4.3 + 6.2 and M 200 c DM = 0.55 − 0.14 + 0.15 × 10 12 M ⊙ . This corresponds to a total Milky Way mass of M 200 c = 0.64 − 0.14 + 0.15 × 10 12 M ⊙ , which is on the low end of the historic range of the galaxy’s mass, but in line with other recent estimates.

Astronomy & Astrophysics↗

Interplanetary dust measurements near the earth

Interplanetary dust measurements near earth compared to theories predicting dust characteristics, discussing concentration, flux, impact rate and solar radiation pressure

Bandermann, L. W.↗