Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Compression fatigue behavior of composites in the presence of delaminations

Three different stacking sequences of a 64-ply layup were tested in an experimental investigation of the effect of idealized imbedded delaminations on the compression fatigue behavior of quasi-isotropic T300/5208 graphite-epoxy laminates. Postfailure examination of specimen cross sections revealed the absence of any fiber microbuckling, suggesting that the predominant failure mode was the propagation of imbedded delaminations in the tab region. One- and two-dimensional delaminations, respectively located across the entire width below the surface ply and buried one or four plies below the surface, were considered. A novel procedure employing minute, laser-drilled holes was successfully used in extending the application of diidobutane-enhaced radiography to buried delaminations.

Ramkumar, R. L.↗

Preliminary measurements of velocity, density and total temperature fluctuations in compressible subsonic flow

The heat transfer characteristics of a three-wire hot-wire probe operated with a constant temperature anemometer were investigated in the subsonic compressible flow regime. The sensitivity coefficients, with respect to velocity, density and total temperature, were measured and the results were used to calculate the velocity, density, and total temperature fluctuations in the test section of the Langley 0.3-m Transonic Cryogenic Tunnel (TCT). These results were extended to give estimates for fluctuations due to vorticity, sound, and entropy. In addition, attempts were made to determine the major source of disturbances in the 0.3-m TCT.

Stainback, P. C.↗

Turbulent compressible convection in a deep atmosphere. I - Preliminary two-dimensional results

The turbulent convection of a compressible fluid in a deep atmosphere is simulated by two-dimensional numerical computations, displaying coexisting 'cells' whose sizes range from the total depth of the convection zone to the smallest scale height at the top. While the largest cells traverse the entire zone, smaller ones are clustered near the top. The vertical correlation length of the vertical velocity is proportional to the local pressure or density scale height, in a way reminiscent of the concept of mixing length.

Chan, K. L.↗

Magnetic field compression at the dayside magnetopause

The degree of compression sustained by the solar wind field as it convects to the magnetopause has been determined empirically with magnetometer data from ISEE 3 in the solar wind and ISEE 1 in the magnetosheath. At the stagnation point, the strength B(SH) of the magnetosheath field may be expressed as B(SH) = square root of 4 X B(SW)' X B(ST), which implies that B(SH) is equal to the geometric mean of the stagnation field strength B(ST) and the shocked solar wind field, approximated by 4 X B(SW)'. For the usual spiral wind pattern of the solar wind field, B(SH) on the duskside of the magnetopause is about 20 percent stronger than it is on the downside. No dependence of B(SH) on the sign of the north-south component of the solar wind field is apparent.

Crooker, N. U.↗

Quantitative measurement of density and velocity in compressible flows using laser-induced iodine fluorescence

A nonintrusive optical technique for the quantitative measurement of molecular density and velocity at a point or in an entire cross-sectional plane of a compressible flowfield is reported. Iodine molecules, seeded into the flowfield reservoir, are excited by a tunable narrow-bandwidth laser and the resulting spatially-resolved fluorescence is collected by a single- or multiple-element detector. A theoretical model for the iodine laser-induced fluorescence process is essential for quantitative measurements and is developed using a rate-equation approach. Density measurements using laser-induced fluorescence are normally complicated by collisional quenching; however, the theory predicts that the off-resonant fluorescent signal is directly proportional to density. Velocity is directly related to the Doppler shift of the iodine absorption line, determined by monitoring the broadband fluorescent signal as the laser is tuned in frequency. Experiments in a steady supersonic flowfield are compared with numerical calculations to demonstrate the accuracy of the approach for density and velocity measurement and the lack of perturbation to the flowfield by the iodine seeding. Extensions of the current approach to density and velocity measurement in lower Mach number flows, to the measurement of pressure and temperature, and to temporally-resolved measurements are discussed.

Mcdaniel, J. C.↗

Turbulence measurements in a compressible reattaching shear layer

Detailed hot-wire measurements of the longitudinal component of the mass-flow fluctuations have been made in an approximately self-preserving free shear layer reattaching on a 20 degree ramp at Mach number of 2.9. The experimental configuration is especially designed to provide a well-defined initial condition for the reattachment process. The absolute mass-flow turbulence intensity increases dramatically through the compression in the reattachment region, which is in sharp contrast to similar subsonic reattachments. It is clear that the mean dilatation contributes significantly to the turbulence amplification. In addition, the length scale is affected strongly by the presence of extra strain rates. Prediction of this flow will require some sophisticated modelling, and the challenge to the predictor is clear.

Hayakawa, K.↗

A new architecture for adaptive transform compression of NTSC composite video signal

In orthogonal transform coding of NTSC video signal, the data is processed in blocks. Processing a block of data that is maximally correlated leads to larger compression. This paper describes a new architecture for arranging the pixels in a block that yields higher correlation than the adjacent pixel blocks. The data is processed using adaptive, intrafield, discrete cosine transform, variable bit allocation coding. In subjective tests, the picture quality was good for an average of about 2 bits/pel for intrafield processing.

Ekambaram, C.↗

Superplastic forming/weld-brazing of titanium skin-stiffened compression panels

A study was conducted to exploit the processing advantages of superplastic forming and weld-brazing for the fabrication of titanium skin-stiffened structural components. Small titanium compression panels were fabricated and tested at room temperature. Stiffeners having configurations of a conventional hat shape, beaded shaped web, ribbed shaped web, or stepped shaped web were investigated. The data from the panel tests included load-shortening curves, local buckling strengths, and failure loads. Experimental buckling loads were compared with buckling loads calculated using a finite-element analysis. The superplastic formed/weld-brazed panels having complex shaped stiffeners developed from 20 to 58 percent higher local buckling strengths than panels with conventionally shaped stiffeners.

Royster, D. M.↗

An analysis of the two-dimensional acoustic field in a nonuniform duct carrying compressible flow

An analytical/numerical linear acoustic solution in a nonuniform two-dimensional duct carrying a compressible mean flow is developed. A quasi-one dimensional mean flow model is employed together with a consistent expression for the cross-flow velocity. The acoustic solution is obtained using the Wave Envelope Method. Numerical results are compared with those of an existing Wave Envelope solution which includes a more general mean flow model. In addition, the singular behavior of the solutions derived in the current work for nearly sonic flow conditions is examined explicitly.

Uenishi, K.↗

Postbuckling of long orthotropic plates in combined shear and compression

The nonlinear large-deflection partial differential equations of von karman for orthotropic plates loaded in combined shear and compression are converted into a set of first-order nonlinear ordinary differential equations by assuming trigonometric functions in one direction. These equations are solved numerically using a two point boundary problem solver which makes use of Newton's method. Results are obtained which determine the postbuckling behavior of rectangular plates with loading up to about three times the buckling load. Both isotropic and orthotropic composite plates are considered. Results show that orthotropic plates may behave quite differently than isotropic plates and that in-plane boundary conditions are important for plates loaded in shear.

Stein, M.↗

Human respiration at rest in rapid compression and at high pressures and gas densities

The ventilation (V), end-tidal PCO2 (PACO2), and CO2 elimination rate were determined in men at rest breathing CO2-free gas over the pressure range 1-50 ATA and the gas density range 0.4-25 g/l, during slow and rapid compressions, at stable elevated ambient pressures and during slow decompressions. Progressive increase in pulmonary gas flow resistance due to elevation of ambient pressure and inspired gas density to the He-O2 equivalent of 5000 feet of seawater was found to produce a complex pattern of change in PACO2. It was found that as both ambient pressure and pulmonary gas flow resistance were progressively raised, PACO2 at first increased, went through a maximum, and then declined towards values near the 1 ATA level. It is concluded that this pattern of PACO2 change results from the interaction on ventilation of the increase in pulmonary resistance due to the elevation of gas density with the increase in respiratory drive postulated as due to generalized central nervous system excitation associated with exposure to high hydrostatic pressure. It is suggested that a similar interaction exists between increased gas flow resistance and the increase in respiratory drive related to nitrogen partial pressure and the resulting narcosis.

Gelfand, R.↗

Three-dimensional compressible viscous analysis of mixer nozzles

An analysis-based design procedure for compound-mixer exhaust nozzles is presented and compared to test data. The design approach is based on two numerical solutions to the 3-D viscous compressible Navier-Stokes equations: an equation splitting technique used for the analysis of the core and bypass flow, and a parabolic marching scheme used in the analysis of the mixing duct. The selection of the analytical methods through test data comparisons and their coupling into an integrated design system are discussed. NASA test data is used to demonstrate the validity of the computations from the exhaust system rating station, upstream of the mixer lobe, to the nozzle throat. An estimate is made of the savings in development time and cost utilizing the new procedure.

Goyal, R. K.↗

Turbulence modeling methods for the compressible Navier-Stokes equations

Turbulence modeling methods for the compressible Navier-Stokes equations, including several zero- and two-equation eddy-viscosity models, are described and applied. Advantages and disadvantages of the models are discussed with respect to mathematical simplicity, conformity with physical theory, and numerical compatibility with methods. A new two-equation model is introduced which shows advantages over other two-equation models with regard to numerical compatibility and the ability to predict low-Reynolds-number transitional phenomena. Calculations of various transonic airfoil flows are compared with experimental results. A new implicit upwind-differencing method is used which enhances numerical stability and accuracy, and leads to rapidly convergent steady-state solutions.

Coakley, T. J.↗

Numerical solution of the Navier-Stokes equations for compressible turbulent two/three dimensional flows in the terminal shock region of an inlet/diffuser

The multidimensional, ensemble-averaged, compressible, time-dependent Navier-Stokes equations in conjunction with mixing length turbulence model and shock capturing technique have been used to study the terminal shock type of flows in various flight regimes occurring in a diffuser/inlet model. The numerical scheme for solving the governing equations is based on a linearized block implicit approach and the following high Reynolds number calculations have been carried out: (1) 2-D, steady, subsonic; (2) 2-D, steady, transonic with normal shock, (3) 2-D, steady, supersonic with terminal shock, (4) 2-D, transient process of shock development and (5) 3-D, steady, transonic with normal shock. The numerical results obtained for the 2-D and 3-D transonic shocked flows have been compared with corresponding experimental data; the calculated wall static pressure distributions agree well with the measured data. The predicted transient responses of the flow to externally applied impulsive disturbance are consistent with results obtained via asymptotic analysis.

Liu, N.-S.↗

Implicit upwind methods for the compressible Navier-Stokes equations

A class of implicit upwind-differencing methods for the compressible Navier-Stokes equations is described and applied. The methods are based on the use of local eigenvalues or wave speeds to control spatial differencing of inviscid terms and are aimed at increasing the level of accuracy and stability achievable in computation. Techniques for accelerating the rate of convergence to a steady-state solution are also used. Applications to inviscid and viscous transonic flows are discussed and compared with other methods and experimental measurements. It is shown that accurate and efficient transonic airfoil calculations can be made on the Cray-1 coomputer in less than 2 min.

Coakley, T. J.↗

Observation of damage growth in compressively loaded laminates

Graphite/epoxy laminates have a definite advantage with respect to the strength-to-weight relation over many standard engineering materials used in aerospace applications. However, this advantage is somewhat reduced by the sensitivity of these laminates to operational hazards, which include a low-velocity impact by foreign objects. Investigations conducted by Chai (1982) and Knauss et al. (1980) have been concerned with the growth of impact damage in compressively loaded laminates, and the visualization of such an impact damage. The present study represents a condensation of parts of these investigations, taking into account a determination of the damage-growth mechanism via real-time recording of the impact event. The material considered, a T300/5208 graphite/epoxy laminate, is typical of the configuration proposed for future heavily loaded primary structures. It has stiffness properties similar to those of the wing skins in existing transport aircraft.

Knauss, W. G.↗

A note on compressibility and energy cascade in turbulent molecular clouds

Observed velocity-size correlations are reexamined in the light of an improved theory of turbulent energy cascade that is developed. It is shown that observed velocity-size correlations cannot be compared with the Kolmogorov law, which is based on incompressible turbulent flow. The fact that the log v-log(l/rho) scaling law (v the turbulent velocity, l the associated region size, and rho the fluid density) predicted for compressible energy cascade is always steeper than that observed in molecular clouds indicates the injection rather than the dissipation of mechanical energy at smaller scales of motion. It is also shown that the concept of strict energy cascade may not be generally applicable in the interstellar medium. The agreement between theory and observation turns out to be best for small cool clouds and cloud cores, suggesting that, for these regions at least, the dominant process in establishing the observed v-l-rho correlation is a turbulent energy cascade.

Fleck, R. C., Jr.↗

The treatment of convected vortices in compressible potential flow

A method is described for incorporating line vortices into the three dimensional compressible potential flow equation. A modified Biot-Savart law is used to compute a vortical velocity field, which is added to the gradient of the potential to form a total velocity. A rapidly converging approximate factorization (AFZ) scheme is then used to compute a potential such that the modified potential flow equation as well as the appropriate boundary conditions, based on total velocity, are satisfied. As part of a coupled iteration procedure, the positions of the line vortices are computed so that they convect with the total flow. The method is used to compute the field due to a single line vortex convecting past a wing. This represents an approximation of the effect of a canard or other lifting surface ahead of the wing, which sheds a tip vortex. It is seen that the flow field is substantially modified by the passage of the vortex. Unlike Euler equation schemes, which are also used to compute these flows, the solutions exhibit no numerical diffusion: The convected vortices retain their initial upstream width. Euler solutions, on the other hand, involve a vorticity which is numerically convected in an Eulerian frame and, unless extensive adaptive grid refinement is used they result in vortices with spread as they convect. Also, the potential flow method requires approximately two orders of magnitude less computing time and much less computer storage than the Euler methods.

Steinhoff, J.↗