Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98

Cross-flow effects on the boundary layer in a plane of symmetry

The validity of 'effective cone analysis' in estimating the boundary-layer properties of bodies in hypersonic flow is discussed. Simple formulas are derived for noncircular cones at angles of attack and are used to show that effective cone analysis only accounts for the increase in the local edge Reynolds number due to the angle of attack. A correction factor depending on the cross flow produced by the transverse curvature of the body and on the angle of attack is shown to reconcile the effective cone approach with the predictions of exact theory.

Agnone, A.↗

Performance of large-bore tapered-roller bearings under combined radial and thrust load at shaft speeds to 15,000 rpm

The performance of 120.65-mm bore tapered roller bearings was investigated at shaft speeds up to 15,000 rpm. Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied by either jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

Parker, R. J.↗

Lubrication of high-speed, large bore tapered-roller bearings

The performance of 120.65-mm- (4.75-in.-) bore tapered-roller bearings was investigated at shaft speeds up to 15,000 rpm (18,000 DN). Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied either by jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

Parker, R. J.↗

Lubrication of high-speed, large bore tapered-roller bearings

The performance of 120.65-mm bore tapered-roller bearings was investigated at shaft speeds up to 15,000 rpm. Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied either by jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

Parker, R. J.↗

Crack-opening displacement transducer

Crack-opening displacement transducer consists of 30 deg cone, coil spring, and linear-displacement transducer. Conical probe is used to measure crack opening. Cone is pressed firmly into crack by spring. As applied load causes crack to open up, cone is pushed further into it. Movement of cone, and thus crack growth, is monitored by linear-displacement transducer. Method gives more accurate measurement of crack-opening displacement of very narrow slots.

Simonds, R. A.↗

Ion beam texturing of surfaces

Textured surfaces, typically with conical structures, have been produced previously by simultaneously etching a surface and seeding that surface with another material. A theory based on surface diffusion predicts a variation in cone spacing with surface temperature, as well as a critical temperature below which cones will not form. Substantial agreement with theory has been found for several combinations of seed and surface materials, including one with a high sputter yield seed on a low sputter yield surface (gold on aluminum). Coning with this last combination was predicted by the theory for a sufficiently mobile seed material. The existence of a minimum temperature for the formation of cones should also be important to those interested in ion-beam machining smooth surfaces. Elements contained in the environmental contaminants or in the sputtered alloys or compounds may serve as seed material.

Kaufman, H. R.↗

Application of supersonic linear theory and hypersonic impact methods to three nonslender hypersonic airplane concepts at Mach numbers from 1.10 to 2.86

Aerodynamic predictions from supersonic linear theory and hypersonic impact theory were compared with experimental data for three hypersonic research airplane concepts over a Mach number range from 1.10 to 2.86. The linear theory gave good lift prediction and fair to good pitching-moment prediction over the Mach number (M) range. The tangent-cone theory predictions were good for lift and fair to good for pitching moment for M more than or equal to 2.0. The combined tangent-cone theory predictions were good for lift and fair to good for pitching moment for M more than or equal to 2.0. The combined tangent-cone/tangent-wedge method gave the least accurate prediction of lift and pitching moment. The zero-lift drag was overestimated, especially for M less than 2.0. The linear theory drag prediction was generally poor, with areas of good agreement only for M less than or equal to 1.2. For M more than or equal to 2.), the tangent-cone method predicted the zero-lift drag most accurately.

Pittman, J. L.↗

Monogenetic volcanoes of the terrestrial planets

Monogenetic volcanic activity has produced cinder cones and small shield volcanoes on the earth, moon, and Mars. Extraterrestrial cinder cones have median volumes only 25% as large as average terrestrial cinder cones, implying that their magma chambers are smaller and shallower (1 km depth vs 3 km). Ejection velocities for lunar and Martian cinder cones range from 20 to 70 m/sec, only 1/3 to 1/10 as high as for equal volume terrestrial eruptions. These low velocities imply low volatile contents for both Martian and lunar magmas.

Wood, C. A.↗

Optical analysis of Cassegrainian concentrator systems

Cone optics procedures have been developed to treat optical systems employing multiple reflectors. The objective of the procedures is to develop efficient techniques to treat multiple reflections of cones when the secondary reflecting surface is curved - in fact, curved differently in different directions. The particular optical system under consideration is the Cassegrainian Concentrator System - a system consisting of a paraboloidal primary reflector and a confocal hyperboloidal secondary reflector. Multiple reflection cone optics methodology as well as preliminary results for the flux distributions and intercept factors based on it are presented in this paper. It is shown that neglecting local curvature effects of the secondary reflector, i.e. even in the differential solid angle within the sun's cone, may overestimate the peak of the flux distribution at the receiver aperture by a factor of two or more.

Bass, A. H., Jr.↗

Reusable captive blind fastener

A one piece reusable fastener capable of joining materials together from one side (blind backside) comprises a screw driven pin ending in a wedge-shaped expander cone. The cone cooperates within a slotted collar end which has a number of tangs on a cylindrical body. The fastener is set by inserting it through aligned holes in the workpieces to be joined. Turning the pin in one direction draws the cone into the collar, deforming the tangs radially outward to mate with tapered back-tapered hold in the workpiece, thus fastening the two pieces together. Reversing the direction of the pin withdraws the cone from the collar, and allows the tangs to resume their contracted configuration without withdrawing the fastener from the insertion hole. The fastener is capable of joining materials together from only one side with substantial strength in tension and shear over many resue attachment cycles, with no special operations on the main assembly parts other than the tapering of the back end of the insertion hole.

Peterson, S. A.↗

Initial '80s Development of Inflated Antennas

State of the art technology was considered in the definition and documentation of a membrane surface suitable for use in a space reflector system for long durations in orbit. Requirements for a metal foil-plastic laminate structural element were determined and a laboratory model of a rigidized element to test for strength characteristics was constructed. Characteristics of antennas ranging from 10 meters to 1000 meters were determined. The basic antenna configuration studied consists of (1) a thin film reflector, (2) a thin film cone, (3) a self-rigidizing structural torus at the interface of the cone and reflector; and (4) an inflation system. The reflector is metallized and, when inflated, has a parabolic shape. The cone not only completes the enclosure of the inflatant, but also holds the antenna feed at its apex. The torus keeps the inflated cone-reflector from collapsing inward. Laser test equipment determined the accuracy of the inflated paraboloids.

Friese, G. J.↗

Free stream noise and transition measurements in a Mach 3.5 pilot quiet tunnel

Free stream fluctuating pressures are determined from hot-wire measurements in a Mach 3.5 pilot quiet nozzle over a unit Reynolds number range from 10-60 million per meter. Further, the transition Reynolds numbers on a sharp tip 5 degree half-angle cone at zero angle of attack are obtained over the same range of unit Reynolds numbers from equilibrium temperature measurements on the cone. Results show that the nozzle provides noise levels in the upstream regions of the test rhombus that are substantially lower than in conventional nozzles. The normalized rms levels of the fluctuating static pressures are found to vary from extremely low values of less than 0.03% up to about 0.8% depending on the unit Reynolds number, the axial location in the test rhombus, and the bleed slot flow. By opening the boundary-layer bleed flow, the wall boundary layers over upstream regions of the nozzle become laminar and the absence of high frequency radiated noise then results in cone transition Reynolds numbers that are in the range of free-flight data. As the unit Reynolds numbers are increased, the nozzle wall boundary layers become transitional and turbulent, and the noise increases to peak levels of about 0.5% with significant energy up to 150 KHz. The cone transition Reynolds numbers then decrease to values that are in the range of those measured in conventional wind tunnels.

Beckwith, I. E.↗

Diffuser/ejector system for a very high vacuum environment

Turbo jet engines are used to furnish the necessary high temperature, high volume, medium pressure gas to provide a high vacuum test environment at comparatively low cost for space engines at sea level. Moreover, the invention provides a unique way by use of the variable area ratio ejectors with a pair of meshing cones are used. The outer cone is arranged to translate fore and aft, and the inner cone is interchangeable with other cones having varying angles of taper.

Riggs, K. E.↗

Experimental and predicted heating distributions for biconics at incidence in air at Mach 10

Heating distributions were measured on a 1.9-percent-scale model of a generic aeroassisted vehicle proposed for missions to a number of planets and for use as a moderate lift-drag ratio Earth orbital transfer vehicle. This vehicle is spherically blunted, 12.84 deg/7 deg biconic with the fore-cone bent upward 7 deg to provide self-trim capability. A straight biconic with the same nose radius and the same half-angles was also tested. The free-stream Reynolds numbers based on model length were equal to about 2 x 10(5) or 9 x 10 (5). The angle of attack, referenced to the aft-cone, was varied from 0 deg to 20 deg. Heating distributions predicted with a parabolized Navier-Stokes (PNS) code are compared with the measurements for the present Reynolds numbers and range of angles of attack. Leeward heating was greatly affected by Reynolds number, with the heating increasing with decreasing Reynolds number for attached flow (low incidence). The opposite was true for separated flow, which occurred when the fore-cone angle of attack exceeded 0.8 times the fore-cone half-angle. Windward heating distributions were predicted to within 10 percent with the PNS code. Leeward heating distributions were predicted qualitatively for both Reynolds numbers, but quantitative agreement was poorer than on the windward side.

Miller, C. G., III↗

An aerothermodynamic study of slender conical vehicles

A numerical study was performed to assess the applicability of some current techniques which can be used for aerothermal predictions over slender spherically blunted cones. Predictions using a viscous-shock-layer method and several engineering approaches were compared with experimental results from flight and ground-based tests, with each other, and with other detailed results. Good agreement was obtained in comparisons with laminar and turbulent heating data from the Reentry F flight vehicle and with the wind-tunnel data. In particular, the viscous-shock-layer method was shown to yield excellent comparisons and should be useful in providing detailed flowfield and surface values for slender blunted cones. Additional predictions were obtained with these methods for two 5-deg half-angle cones with different nose radii to illustrate the effects of nose bluntness and angle of attack on drag and heat transfer. These results demonstrate the benefit of nose blunting with respect to heating and drag for laminar and transitional flow at zero-lift conditions and the benefit of heating reduction at angle of attack. Detailed comparison of the engineering code predictions with the viscous-shock-layer results for these additional cases generally showed good agreement except for the laminar prodictions at angle of attack on the forward cone surface. Nonequilibrium calculations at 0-deg angle of attack showed that substantial benefits of low surface catalysis existed only in the nose-dominated region.

Thompson, R. A.↗

Phase calibration generator

A phase calibration system was developed for the Deep Space Stations to generate reference microwave comb tones which are mixed in with signals received by the antenna. These reference tones are used to remove drifts of the station's receiving system from the detected data. This phase calibration system includes a cable stabilizer which transfers a 20 MHz reference signal from the control room to the antenna cone. The cable stabilizer compensates for delay changes in the long cable which connects its control room subassembly to its antenna cone subassembly in such a way that the 20 MHz is transferred to the cone with no significant degradation of the hydrogen maser atomic clock stability. The 20 MHz reference is used by the comb generator and is also available for use as a reference for receiver LO's in the cone.

Sigman, E. H.↗

On the precipitation of relativistic electrons from the outer belt

A model in which a partially filled drift loss cone plays a prominent role is presently used to investigate relativistic electron data obtained by the Defense Meteorological Satellite Program spacecraft in the outer belt region. The good agreement obtained between model predictions and observations indicates that electron drift in the drift loss cone, which is known to dominate electron precipitation phenomena at lower latitudes, is also important at outer beta latitudes. In conjunction with the degree of partial filling of the drift loss cone, this effect indicates that slow pitch angle diffusion dominates the morphology of outer belt electrons. It is concluded that half of the electron precipitation from the outer belt is due to wave-particle interactions, and the other half by auroral activity and electron drift in the drift loss cone.

Sheldon, W. R.↗

On the stability of compressible flow past axisymmetric bodies

Compressible linear stability theory for axisymmetric flows is presented. The theory is applied to flow past a cylinder and a sharp cone at a Mach number of 5 with adiabatic wall conditions. The effect of transverse curvature and body divergence is studied. It is found that transverse curvature has a stabilizing influence on axisymmetric (first and second mode) disturbances while it has a destabilizing influence on the asymmetric (oblique first mode) disturbances. The body divergence effects are stabilizing for both symmetric and asymmetric disturbances. Comparisons made with the results of planar stability theory show that, for a cylinder, curvature effects become more pronounced with increasing distance along the cylinder. For a sharp cone, these effects become less significant further away from the cone tip since the body radius increases faster than the growth of the boundary layer. The effect of cone angle on stability is also studied.

Malik, M. R.↗