Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,765 records · Page 98
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Structure and Anticorrosion, Friction, and Wear Characteristics of Pure Diamond-Like Carbon (DLC), Cr-DLC, and Cr-H-DLC Films on AZ91D Mg Alloy

This study evaluated the protection against corrosion and wear afforded to AZ91D Mg alloy by coatings of hydrogen-free and low-Cr-doped hydrogenated diamond-like carbon (DLC) films. The microstructure and corrosion resistance were evaluated using scanning electron microscopy, atomic force microscopy, Raman spectroscopy, polarization curves, and neutral salt spraying tests. Wear tests were performed to investigate the friction and wear behaviors of the samples against 9Cr18 in humid air, deionized water, and 3.5 wt.% NaCl solution using a reciprocating sliding test in the ball-on-disk mode. The results showed that the more compact Cr-H-DLC film improved the corrosion resistance of the Mg alloy, whereas the Cr-DLC film accelerated the corrosion in the 3.5 wt.% NaCl solution. All Mg alloy samples coated with DLC films exhibited low coefficient of friction (COF) values and smaller wear volumes compared with those of bare substrate in air, water, or NaCl solution. The Cr-DLC film presented the lowest COF and wear rate in air, but the worst corrosion protection in air and NaCl solution, whereas the converse was found for the Cr-H-DLC film. Unfortunately, all coated samples showed limited protection ability because of pore defects in the films, high galvanic potential between the substrate and the buffer layer or film, and high electrical conductivity, which caused severe tribocorrosion of the Mg alloy during the wear tests in NaCl solution. The corrosion protection ability of DLC films is key to the wear resistance protection of Mg alloys in water or NaCl solution.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Beyond Atomic Sizes and Hume-Rothery Rules: Understanding and Predicting High-Entropy Alloys

High-entropy alloys constitute a new class of materials that provide an excellent combination of strength, ductility, thermal stability, and oxidation resistance. Although they have attracted extensive attention due to their potential applications, little is known about why these compounds are stable or how to predict which combination of elements will form a single phase. Here, we present a review of the latest research done on these alloys focusing on the theoretical models devised during the last decade. We discuss semiempirical methods based on the Hume-Rothery rules and stability criteria based on enthalpies of mixing and size mismatch. To provide insights into the electronic and magnetic properties of high-entropy alloys, we show the results of first-principles calculations of the electronic structure of the disordered solid-solution phase based on both Korringa Kohn Rostoker coherent potential approximation and large supercell models of example face-centered cubic and body-centered cubic systems. Furthermore, we discuss in detail a model based on enthalpy considerations that can predict which elemental combinations are most likely to form a single-phase high-entropy alloy. The enthalpies are evaluated via first-principles high-throughput density functional theory calculations of the energies of formation of binary compounds, and therefore it requires no experimental or empirically derived input. Finally, the model correctly accounts for the specific combinations of metallic elements that are known to form single-phase alloys while rejecting similar combinations that have been tried and shown not to be single phase.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Initial assessment of Ni-base alloy performance in 0.1 MPa and supercritical CO 2

There is considerable interest in increasing the working temperature of both open and closed supercritical CO 2 (sCO 2 ) cycles to ≥700 °C. At these temperatures, it is unlikely that any Fe-base alloys have suitable strength and therefore the focus is on Ni-base alloys for this application. To begin addressing the lack of compatibility data under these conditions, initial work exposed a wide range of candidate alloys in 500-h exposures at 20 MPa (200 bar) CO 2 at 650 -750 °C in high purity CO 2 . In general, the reaction products were thin and protective in these exposures. A smaller group of alloy coupons focusing on chromia- and alumina-forming alloys was exposed for 500h in 0.1 MPa (1bar) air, CO 2 , CO 2 +O 2 and CO 2 +H 2 O for comparison. Thus, the thin surface oxides formed were very similar to those formed at high pressure and no clear detrimental effect of CO 2 oxidation or O 2 or H 2 O impurities could be observed in these exposures.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Cerium-based, intermetallic-strengthened aluminum casting alloy: High-volume co-product development

Here, several rare earth elements are considered by-products to rare earth mining efforts. By using one of these by-product elements in a high-volume application such as aluminum casting alloys, the supply of more valuable rare earths can be globally stabilized. Stabilizing the global rare earth market will decrease the long-term criticality of other rare earth elements. The low demand for Ce, the most abundant rare earth, contributes to the instability of rare earth extraction. In this article, we discuss a series of intermetallic-strengthened Al alloys that exhibit the potential for new high-volume use of Ce. The castability, structure, and mechanical properties of binary, ternary, and quaternary Al-Ce based alloys are discussed. We have determined Al-Ce based alloys to be highly castable across a broad range of compositions. Nanoscale intermetallics dominate the microstructure and are the theorized source of the high ductility. In addition, room-temperature physical properties appear to be competitive with existing aluminum alloys with extended high-temperature stability of the nanostructured intermetallic.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Methodology for Thermodynamic Analysis Coupled with Computational Fluid Dynamics Modeling for Casting a Novel Aluminum–Cerium Alloy

In this paper, we present the results of computational fluid dynamics (CFD) analysis to assess castability, porosity, molten metal fluidity and other technological properties of a new Al-Ce alloy. A thermodynamic analysis of a new Al-Ce alloy is done to obtain the physical properties as a function of temperature across both solid and liquid phases. These properties are then used to build the CFD of model the full casting process from initial pouring through to final solidification of the part, here an example of a heavy duty mor mount is used. While several excellent commercial CFD codes exists this process shows that CFD can be used to assess the capability of the alloy to properly fill the mold, as well as give predictions where scattered porosity or large-scale defects may occur in the casting. Further, unlike the commercially available software (e.g., ProCAST, SOLIDCast , MAGMASOFT®) the complex 3D-analysis of the stress / strain fields in cast parts is not performed at this time. However, the availability of free software for assessing the required thermodynamic / thermo-physical properties of new alloys (OpenCALPHAD) and CFD codes such as OpenFOAM® makes the developed option attractive and economical, especially for the analysis of new Al-Ce alloys, for which the available data does not exist.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Doping Effects on the Ductility of a Lightweight Refractory High-Entropy Alloy: Grain Boundary and Bulk Lattice Aspects

Doping elements in small amounts often segregate to grain boundaries (GBs) in alloys and can significantly impact mechanical properties and performance. Refractory high-entropy alloys (RHEAs) are known for their poor ductility, especially at low temperatures. Promoting GB cohesion through segregation can be an effective approach to mitigate embrittlement. Here, in this study, first-principles density functional theory (DFT) calculations were performed to examine the effects of important interstitial dopants (O, B, C, and N) and substitutional dopants (Cr, Y, La, and Ce) on the Σ5(310) [001] tilt GB of a lightweight RHEA Nb 32.5 Ti 27.5 Mo 22.5 Ta 12.5 Hf 2.5 Zr 2.5 . The DFT calculations reveal that certain dopants, such as B, C, Cr, N, and Y, exhibit favorable GB strengthening effects by improving bonding interactions with the bulk alloy. The impact of doping on the ductility parameter of the bulk lattice, defined as the ratio of surface energy to unstable stacking fault energy for the {110} <111> slip system, was also studied; and the results show that doping reduces the intrinsic ductility of the alloy, decreasing the D-parameter from 2.90 to 2.55, depending on the specific dopant. The present findings provide a foundational understanding at atomic level of the effect of representative dopants on mechanical properties of RHEAs and can be used to guide future alloy design for improved mechanical properties.

deformation charge density↗
DOE OSTI2014

The role of nickel in radiation damage of ferritic alloys

According to modern theory, damage evolution under neutron irradiation depends on the fraction of self-interstitial atoms (SIAs) produced in the form of one-dimensional glissile clusters. These clusters, having a low interaction cross-section with other defects, are absorbed mainly by grain boundaries and dislocations, creating the so-called production bias. It is known empirically that the addition of certain alloying elements influences many radiation effects, including swelling; however, the mechanisms are unknown in many cases. In this study, we report the results of an extensive multi-technique atomistic level modeling study of SIA clusters mobility in body-centered cubic Fe–Ni alloys. We have found that Ni interacts strongly with the periphery of clusters, affecting their mobility. The total effect is defined by the number of Ni atoms interacting with the cluster at the same time and can be significant, even in low-Ni alloys. Thus a 1 nm (37SIAs) cluster is practically immobile at T < 500 K in the Fe–0.8 at.% Ni alloy. Increasing cluster size and Ni content enhances cluster immobilization. Finally, this effect should have quite broad consequences in void swelling, matrix damage accumulation and radiation induced hardening and the results obtained help to better understand and predict the effects of radiation in Fe–Ni ferritic alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Mechanisms of radiation-induced segregation in CrFeCoNi-based single-phase concentrated solid solution alloys

Single-phase concentrated solid solution alloys have attracted wide interest due to their superior mechanical properties and enhanced radiation tolerance, which make them promising candidates for the structural applications in next-generation nuclear reactors. However, little has been understood about the intrinsic stability of their as-synthesized, high-entropy configurations against radiation damage. In this paper, we report the element segregation in CrFeCoNi, CrFeCoNiMn, and CrFeCoNiPd equiatomic alloys when subjected to 1250 kV electron irradiations at 400 °C up to a damage level of 1 displacement per atom. Cr/Fe/Mn/Pd can deplete and Co/Ni can accumulate at radiation-induced dislocation loops, while the actively segregating elements are alloy-specific. Moreover, electron-irradiated matrix of CrFeCoNiMn and CrFeCoNiPd shows L1 0 (NiMn)-type ordering decomposition and <001>-oriented spinodal decomposition between Co/Ni and Pd, respectively. Finally, these findings are rationalized based on the atomic size difference and enthalpy of mixing between the alloying elements, and identify a new important requirement to the design of radiation-tolerant alloys through modification of the composition.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Evaluation of an Al-Ce alloy for laser additive manufacturing

Our present research in metal additive manufacturing (AM) focuses on designing processing parameters around existing alloys designed for traditional manufacturing. However, to maximize the benefits of AM, alloys should be designed to specifically take advantage of the unique thermal conditions of these processes. Furthermore, our study focuses on the development of a design methodology for alloys in AM, using a newly developed Al-Ce alloy as an initial case study. To evaluate the candidacy of this system for fusion based additive manufacturing, single-line laser melts were made on cast Al-12Ce plates using three different beam velocities (100, 200, and 300 mm/min). The microstructure was evaluated in the as-melted and heat treated conditions (24 hrs at 300°C). An extremely fine microstructure was observed within the weld pools, evolving from eutectic at the outer solid-liquid boundaries to a primary Al FCC dendritic/cellular structure nearer the melt-pool centerline. We rationalized the observed microstructures through the construction of a microstructure selection map for the Al-Ce binary system, which will be used to enable future alloy design. Interestingly, the heat treated samples exhibited no microstructural coarsening.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Effect of nickel on point defects diffusion in Fe – Ni alloys

Iron-Nickel alloys are perspective alloys as nuclear energy structural materials because of their good radiation damage tolerance and mechanical properties. Understanding of experimentally observed features such as the effect of Ni content to radiation defects evolution is essential for developing predictive models of radiation. Recently an atomic-scale modelling study has revealed one particular mechanism of Ni effect related to the reduced mobility of clusters of interstitial atoms in Fe-Ni alloys. In this paper we present results of the microsecond-scale molecular dynamics study of point defects, i.e. vacancies and self-interstitial atoms, diffusion in Fe-Ni alloys. It is found that the addition of Ni atoms affects diffusion processes: diffusion of vacancies is enhanced in the presence of Ni, whereas diffusion of interstitials is reduced and these effects increase at high Ni concentration and low temperature. As a result, the role of Ni solutes in radiation damage evolution in Fe-Ni alloys is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Irradiation-induced damage evolution in concentrated Ni-based alloys

Understanding the effects of chemical complexity from the number, type and concentration of alloying elements in single-phase concentred solid-solution alloys (SP-CSAs) on defect dynamics and microstructure evolution is pivotal for developing next-generation radiation-tolerant structural alloys. A specially chosen set of SP-CSAs with different chemical complexity (Ni 80 Fe 20 , Ni 80 Cr 20 and Ni 40 Fe 40 Cr 20 ) are investigated using 1.5 MeV Mn ions over a wide fluence range, from 2 × 10 13 to 1 × 10 16 ions cm –2 at room temperature. Based on an integrated study of Rutherford backscattering spectroscopy in channeling geometry and molecular dynamics simulations, the results demonstrate that Ni 40 Fe 40 Cr 20 is more radiation tolerant than Ni 80 Fe 20 , Ni 80 Cr 20 and elemental Ni in the low fluence regime. While chemical complexity of this set of SP-CSAs is clearly demonstrated to affect defect evolution through suppressed defect production and enhanced recombination at early stages, the effect of the mixed ferro- and anti-ferromagnetic interactions is not the only controlling factor responsible for the improved radiation performance. As a result, the observed strong alloying effect on defect evolution is attributed to the altered defect migration mobilities of defect clusters in these alloys, an intrinsic characteristic of the complex energy landscapes in CSAs.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Enhanced high-temperature tensile property by gradient twin structure of duplex high-Nb-containing TiAl alloy

A pre-deformation process was employed for a TiAl alloy via high-temperature torsion, in which the stability of the constituent phases was tailored, resulting in enhanced hardening capability and ductility via a gradient microstructure. A sample with a pre-torsion of 360° exhibited a yield strength of 475 MPa and an ultimate tensile strength of 592 MPa, with a tensile ductility of 47% at 850 °C. The tensile properties were significantly enhanced compared with the as-forged sample, which exhibited values of 395 MPa, 494 MPa, and 4.6%, respectively. The physical mechanisms for the significant enhancement of the mechanical property of the TiAl alloys were studied in-depth via of transmission electron microscopy, electron-backscattered diffraction, and high-energy X-ray diffraction techniques. The high strength is mainly attributed to the twin structure formed during torsion, while high fracture elongation correlates to the recrystallization of the γ phase at twin-twin sections and the load partitioning regulated by a hierarchical microstructure. When the tensile micro-strains along the loading direction and transverse direction in the γ phase of the pre-deformed TiAl alloy, a higher mechanical performance was obtained. Moreover, the fracture mode of the pre-torsional tensile sample is a combination of pores and cleavage facets which resulted from the microstructure after torsion. Finally, the gradient twin structure approach in this study provides a strategy for developing TiAl alloys with exceptionally high-temperature tensile property, and the results of the micromechanical behavior-microstructure-property relationship may improve the understanding of the plastic deformation of TiAl alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Modern data analytics approach to predict creep of high-temperature alloys

A breakthrough in alloy design often requires comprehensive understanding in complex multi-component/multi-phase systems to generate novel material hypotheses. We introduce a modern data analytics workflow that leverages high-quality experimental data augmented with advanced features obtained from high-fidelity models. Herein, we use an example of a consistently-measured creep dataset of developmental high-temperature alloy combined with scientific alloy features populated from a high-throughput computational thermodynamic approach. Extensive correlation analyses provide ranking insights for most impactful alloy features for creep resistance, evaluated from a large set of candidate features suggested by domain experts. We also show that we can accurately train machine learning models by integrating high-ranking features obtained from correlation analyses. Consequently, the demonstrated approach can be extended beyond incorporating thermodynamic features, with input from domain experts used to compile lists of features from other alloy physics, such as diffusion kinetics and microstructure evolution.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of 3d electron configurations on helium bubble formation and void swelling in concentrated solid-solution alloys

Currently, elemental specific chemical complexity is known to play a vital role in microstructure development in single-phase concentrated solid-solution alloys (SP-CSAs), including both He bubble formation and irradiation-induced void swelling. While cavity formation and evolution under ion irradiation at elevated temperature are complex nonequilibrium processes, chemical effects are revealed at the level of electrons and atoms herein in a simplified picture, using Ni and a special set of Ni-based SP-CSAs composed of 3d transition metals as model alloys. Based on Ni and the model alloys with minimized variables (e.g., atomic mass, size, and lattice structure), we report on the effects of chemically-biased energy dissipation, defect energetics, sluggish diffusion, and atomic transport on cavity formation and evolution under both self-ion Ni irradiation and He implantation. The observed difference in microstructure evolution is attributed to the effects of d electron interactions in their integrated ability to dissipate radiation energy. The exhibited impact of alloying 3d transition metals with larger differences in the outermost electron counts suggests a simple design strategy for tuning defect properties to improve radiation tolerance in structural alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The synergistic role of Mn and Zr/Ti in producing θ'/L12 co-precipitates in Al-Cu alloys

Microstructural stability is a critical factor to consider when designing new alloys for high-temperature applications. An Al-Cu alloy with Mn and Zr additions has recently been developed to withstand extended exposures of up to 350 °C. The addition of Mn in combination with Zr and their segregation to precipitate interfaces play a significant role in stabilizing the metastable θ ' precipitates responsible for the alloy&#x27;s hardness; however, adding Zr and Mn separately only improves the stability to 200 °C and 300 °C, respectively. To this end, the effect of the synergistic additions on interfacial structure and chemistry was studied in detail using atom probe tomography (APT) and scanning transmission electron microscopy (STEM) for Al-Cu-Mn-Zr/Ti-containing alloys subjected to long-term annealing (up to 2,100 h) in the critical temperature range, 300 °C and 350 °C, to investigate the role of Zr/Ti in increasing the θ '-precipitate stability. The APT and STEM results reveal that Mn additions stabilize θ ' long enough for the slower diffusing Zr atoms to segregate to coherent θ ' interfaces that eventually create a θ '/ L1 2 -Al 3 (Zr x ,Ti 1-x ) co-precipitate structure. The co-precipitate is highly stable, as shown by density functional theory calculations, and is a key factor that governs microstructural stability beyond 300 °C. This study reveals how solute additions with different stabilization mechanisms can work in concert to stabilize a desired microstructure, and the results provide insights that can be applied to other high-temperature alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pseudoelastic deformation in Mo-based refractory multi-principal element alloys

Phase diagrams supported by density functional theory methods can be crucial for designing high-entropy alloys that are subset of multi-principal-element alloys. We present phase and property analysis of quinary (MoW) x Zr y (TaTi) 1-x-y refractory high-entropy alloys from combined Calculation of Phase Diagram (CALPHAD) and density-functional theory results, supplemented by molecular dynamics simulations. Both CALPHAD and density-functional theory analysis of phase stability indicates a Mo-W-rich region of this quinary has a stable single-phase body-centered-cubic structure. We report first quinary composition from Mo-W-Ta-Ti-Zr family of alloy with pseudo-elastic behavior, i.e., hysteresis in stress-strain. Our analysis shows that only Mo-W-rich compositions of Mo-W-Ta-Ti-Zr, i.e., Mo+W, show reproducible hysteresis in stress-strain responsible for pseudo-elastic behavior. The (MoW) 85 Zr 7.5 (TaTi) 7.5 was down-selected based on temperature-dependent phase diagram analysis and molecular dynamics simulations predicted elastic behavior that reveals twinning-assisted pseudoelastic behavior. While mostly unexplored in body-centered-cubic crystals, twinning is a fundamental deformation mechanism that competes against dislocation slip in crystalline solids. Furthermore, this alloy shows identical cyclic deformation characteristics during uniaxial < 100 > loading, i.e., the pseudoelasticity is isotropic in loading direction. Additionally, a temperature increase from 77 to 1,500 K enhances the elastic strain recovery in load-unload cycles, offering possibly control to tune the pseudoelastic behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A data science approach for analysis and reconstruction of spinodal-like composition fields in irradiated FeCrAl alloys

A statistical method for the analysis of continuously distributed data representative of composition fluctuations in irradiated FeCrAl alloys acquired using Energy Dispersive X-ray Spectroscopy (EDS) method is presented. Using probability distribution functions, direct and cross-covariances between the elemental compositions, the effects of alloy composition and irradiation dose were investigated on the spatial distribution and length scale of composition fluctuations at the nanoscale. We have observed that, for neutron-irradiated FeCrAl alloys, the distribution of Fe and Cr followed a left-skewed and right-skewed distribution, respectively for all (average) alloy compositions and irradiation doses. The analysis also revealed enhanced spatial gradients in the elemental compositions at higher irradiation dose. Direct and cross-covariance estimates of the experimental data were also utilized for reconstruction of composition data through fitting it to a parametric form of the covariance functions. Linear Model of Coregionalization was used to determine the parameters of the covariance functions. Subsequently, a spectral method was utilized for simulating a realization of the alloy compositions. Close correspondence was observed between the experimental and the reconstructed data which was analyzed using probability distribution functions and covariance functions. Composition space of the experimental and reconstructed data and dislocation velocities as a function of applied stress and line directions over the entire composition maps were also examined.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Intermetallic particle heterogeneity controls shear localization in high-strength nanostructured Al alloys

The mechanical behavior of two nanocrystalline Al alloys, Al-Mg-Y and Al-Fe-Y, is investigated with in-situ micropillar compression testing. Both alloys were strengthened by a hierarchical microstructure including grain boundary segregation, nanometer-thick amorphous complexions, carbide nanorod precipitates with sizes of a few nanometers, and submicron-scale intermetallic particles. The maximum yield strength of the Al-Mg-Y system is measured to be 950 MPa, exceeding that of the Al-Fe-Y system (680 MPa), primarily due to a combination of more carbide nanorods and more amorphous complexions. Both alloys exhibited yield strengths much higher than those of commercial Al alloys, and therefore have great potential for structural applications. However, some micropillar specimens were observed to plastically soften through shear banding. Post-mortem investigation revealed that intermetallic-free deformation pathways of a few micrometers in length were responsible for this failure. Further characterization showed significant grain growth within the shear band. The coarsened grains maintained the same orientation with each other, pointing to grain boundary mechanisms for plastic flow, specifically grain rotation and/or grain boundary migration. Here, the presence of intermetallic particles makes it difficult for both matrix and intermetallic grains to rotate into the same orientation due to the different lattice parameters and slip systems. Therefore, we are able to conclude that a uniform distribution of intermetallic particles with an average spacing less than the percolation length of shear localization can effectively prevent the maturation of shear bands, offering a design strategy for high-strength nanocrystalline Al alloys with both high strength and stable plastic flow.

36 MATERIALS SCIENCE↗