Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “time migration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Variation of a Defect Structure of Lithium Tetraborate (Li{sub 2}B{sub 4}O{sub 7}) in an External Electric Field

The variation of a defect structure of a lithium tetraborate single crystal under the influence of a high-strength external electric field applied along polar direction [001] has been studied by the X-ray diffraction (XDR) method. The conductivity kinetics has been measured; it is found to agree with changes in the diffraction peak parameters. Application of the electric field with the strength of 300–500 V/mm leads to a sharp broadening of the rocking curve and the increase in the integral intensity by several times, but the curve position and shape are only slightly changed. At higher electric fields from 500 to 1500 V/mm, the process of broadening the curve slows down; however, the shape asymmetry appears and the peak shifts to smaller angles, which is due to an increase in the lattice parameter along axis c. In this case, the changes become irreversible, since the distorted structure is partially recovered with a very low rate (for several months). Two types of the dependences of the rocking curves parameters variation under an external field are interpreted as the manifestation of two mechanisms of the ionic conduction due to mobile lithium (Li{sup +}) ions at low fields and oxygen vacancies (V{sub O}{sup 2+}) at higher fields. The charge carrier migration leads to an increase in the defect concentration and structural changes in a near-surface crystal region. The obtained results have practical importance from the point of view of the controlled change in the defect structure in the crystals with ionic conductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

SPECIAL ANALYSIS AIR PATHWAY MODELING OF E-AREA LOW-LEVEL WASTE FACILITY

This Special Analysis (SA) was initiated to address a concern expressed by the Department of Energy's Low Level Waste Disposal Facility Federal Review Group (LFRG) Review Team during their review of the 2008 E-Area Performance Assessment (PA) (WSRC, 2008). Their concern was the potential for overlapping of atmospheric plumes, emanating from the soil surface above SRS LLW disposal facilities within the E-Area, to contribute to the dose received by a member of the public during the Institutional Control (IC) period. The implication of this concern was that the dose to the maximally-exposed individual (MEI) located at the SRS boundary might be underestimated during this time interval. To address this concern a re-analysis of the atmospheric pathway releases from E-Area was required. In the process of developing a new atmospheric release model (ARM) capable of addressing the LFRG plume overlap concern, it became obvious that new and better atmospheric pathway disposal limits should be developed for each of the E-Area disposal facilities using the new ARM. The scope of the SA was therefore expanded to include the generation of these new limits. The initial work conducted in this SA was to develop a new ARM using the GoldSim{reg_sign} program (GTG, 2009). The model simulates the subsurface vapor diffusion of volatile radionuclides as they release from E-Area disposal facility waste zones and migrate to the land surface. In the process of this work, many new features, including several new physical and chemical transport mechanisms, were incorporated into the model. One of the most important improvements was to incorporate a mechanism to partition volatile contaminants across the water-air interface within the partially saturated pore space of the engineered and natural materials through which vapor phase transport occurs. A second mechanism that was equally important was to incorporate a maximum concentration of 1.9E-07 Ci/m{sup 3} of {sup 14}CO{sub 2} in the air-filled pores of cementitious materials. The ARM also combines the individual transport models constructed for each E-Area disposal facility into a single model, and was ultimately used to analyze the LFRG concern regarding the potential for atmospheric plume overlap at the SRS boundary during the IC period. To evaluate the plume overlap issue, a conservative approach was adopted whereby the MEI at the SRS boundary was exposed to the releases from all E-Area disposal facilities simultaneously. This is equivalent to a 100% overlap of all atmospheric plumes emanating from E-Area. Should the dose received from this level of atmospheric plume overlap still fall below the permissible exposure level of 10 mrem/yr, then the LFRG concern would be alleviated. The structuring of the ARM enables this evaluation to be easily performed. During the IC period, the peak of the 'total plume overlap dose' was computed to be 1.9E-05 mrem/yr, which is five orders of magnitude lower than the 10 mrem/yr PA performance objective for the atmospheric release pathway. The main conclusion of this study is that for atmospheric releases from the E-Area disposal facilities, plume overlap does not cause the total dose to the MEI at the SRS boundary during the IC to exceed the Performance Assessment (PA) performance objective. Additionally, the potential for plume overlap was assessed in the post-Institutional Control period. Atmospheric plume overlap is less likely to occur during this period but conceivably could occur if the prevailing wind direction shifted so as to pass directly over all EArea disposal facilities and transport airborne radionuclides to the MEI at the 100 m point of compliance (POC). This concern was also demonstrated of little concern, as the maximum plume overlap dose was found to be 1.45E+00 mrem/yr (or {approx}15% of the performance measure) during this period and under these unlikely conditions.

54 ENVIRONMENTAL SCIENCES↗

A NEW MECHANISM FOR RADIAL MIGRATION IN GALACTIC DISKS: SPIRAL-BAR RESONANCE OVERLAP

While it has long been known that a large number of short-lived transient spirals can cause stellar migration, here we report that another mechanism is also effective at mixing disks of barred galaxies. The resonance overlap of the bar and spiral structure (SS) induces a nonlinear response leading to a strong redistribution of angular momentum in the disk. We find that, depending on the amplitudes of the perturbers, the changes in angular momentum, {Delta}L, could occur up to an order of magnitude faster than in the case of recurrent spirals. The signature of this mechanism is a bimodality in {Delta}L with maxima near the bar's corotation and its outer Lindblad resonance; this is independent of the properties of the SS. For parameters consistent with the Milky Way, the disk mixes in about 3 Gyr and the stellar velocity dispersion increases with time in a manner roughly consistent with observations. This new mechanism could account for both the observed age-velocity relation and the absence of age-metallicity relation in the solar neighborhood. Spiral-bar interaction could also explain observations showing that strongly barred galaxies have weaker metallicity gradients than weakly barred or non-barred galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗

Direct quantification of ion composition and mobility in organic mixed ionic-electronic conductors

Ion transport in organic mixed ionic-electronic conductors (OMIECs) is crucial due to its direct impact on device response time and operating mechanisms but is often assessed indirectly or necessitates extra assumptions. Operando x-ray fluorescence (XRF) is a powerful, direct probe for elemental characterization of bulk OMIECs and was used to directly quantify ion composition and mobility in a model OMIEC, poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (PEDOT:PSS), during device operation. The first cycle revealed slow electrowetting and cation-proton exchange. Subsequent cycles showed rapid response with minor cation fluctuation (~5%). Comparison with optical-tracked electrochromic fronts revealed mesoscale structure–dependent proton transport. The calculated effective ion mobility demonstrated thickness-dependent behavior, emphasizing an interfacial ion transport pathway with a higher mobile ion density. The decoupling of interfacial effects on bulk ion mobility and the decoupling of cation and proton migration elucidate ion transport in conventional and emerging OMIEC-based devices and has broader implications for other ionic conductors writ large.

42 ENGINEERING↗

Kinetic Simulations of Microstructural Evolution (KSOME)

"Kinetic simulations of microstructural evolution" (KSOME) is an object Kinetic Monte Carlo (OMKC) simulation code. It is developed to simulate microstructural evolution in materials during irradiation. KSOME is developed from ground up with priority given to the flexibility, ease of upgradability, and computation efficiency, in that order. With previously developed simulation codes, various processes (more precisely, the diffusion-reaction processes) that can occur in a system were hardwired into the code. Hence, to perform higher fidelity simulations, a significant coding effort was required every time to incorporate either a more accurate description of existing processes or new processes. With KSOME, the necessity for frequent code upgrades whenever there is a need to perform higher fidelity simulations is either eliminated or reduced significantly. In KSOME, the categories of various diffusion-reaction processes and the data-management system are hardwired, while the execution of the diffusion-reaction processes specific to a system is specified via input files. In the present version of KSOME, the analytical expression required to calculate defect interaction radii are inputted via a text file. However, the ability to parse mathematical expressions from a text file can be extended to input the analytical expression to calculate other defect properties; including the expressions to calculate the change in the migration barriers of mobile defects due to long-range interaction with extended defects

Nandipati, Giridhar [Pacific Northwest National La↗

Isotope exchange kinetics in metal hydrides I : TPLUG model.

A one-dimensional isobaric reactor model is used to simulate hydrogen isotope exchange processes taking place during flow through a powdered palladium bed. This simple model is designed to serve primarily as a platform for the initial development of detailed chemical mechanisms that can then be refined with the aid of more complex reactor descriptions. The one-dimensional model is based on the Sandia in-house code TPLUG, which solves a transient set of governing equations including an overall mass balance for the gas phase, material balances for all of the gas-phase and surface species, and an ideal gas equation of state. An energy equation can also be solved if thermodynamic properties for all of the species involved are known. The code is coupled with the Chemkin package to facilitate the incorporation of arbitrary multistep reaction mechanisms into the simulations. This capability is used here to test and optimize a basic mechanism describing the surface chemistry at or near the interface between the gas phase and a palladium particle. The mechanism includes reversible dissociative adsorptions of the three gas-phase species on the particle surface as well as atomic migrations between the surface and the bulk. The migration steps are more general than those used previously in that they do not require simultaneous movement of two atoms in opposite directions; this makes possible the creation and destruction of bulk vacancies and thus allows the model to account for variations in the bulk stoichiometry with isotopic composition. The optimization code APPSPACK is used to adjust the mass-action rate constants so as to achieve the best possible fit to a given set of experimental data, subject to a set of rigorous thermodynamic constraints. When data for nearly isothermal and isobaric deuterium-to-hydrogen (D {yields} H) and hydrogen-to-deuterium (H {yields} D) exchanges are fitted simultaneously, results for the former are excellent, while those for the latter show pronounced deviations at long times. These discrepancies can be overcome by postulating the presence of a surface poison such as carbon monoxide, but this explanation is highly speculative. When the method is applied to D {yields} H exchanges intentionally poisoned by known amounts of CO, the fitting results are noticeably degraded from those for the nominally CO-free system but are still tolerable. When TPLUG is used to simulate a blowdown-type experiment, which is characterized by large and rapid changes in both pressure and temperature, discrepancies are even more apparent. Thus, it can be concluded that the best use of TPLUG is not in simulating realistic exchange scenarios, but in extracting preliminary estimates for the kinetic parameters from experiments in which variations in temperature and pressure are intentionally minimized.

99 GENERAL AND MISCELLANEOUS↗

Geochemical Processes Governing the Fate and Transport of Chromium(III) and Chromium(VI) in Soils

Chromium has served as an exceptional and necessary elemental component of many industrial processes and consumer products. Its prevalence in the global environment as both a dissolved and wind-borne constituent has prompted concern during the last several decades due to the large migration potential and biological toxicity of various Cr chemical species. The objective of this study was to develop an improved understanding and predictive capability of the rates and mechanisms of competing geochemical redox and sorption reactions that govern the fate and transport of Cr(III) and C(VI) in heterogeneous subsurface environments. Batch and miscible displacement experiments, coupled with solid-phase spectroscopy methods, were utilized to quantify the interaction of Cr with subsurface materials acquired from three geographically distinct locations within the continental United States that represented soils from different Department of Energy facilities known to have issues regarding Cr contamination. Soil chemical and mineralogical properties were found to be important factors controlling the mechanisms of Cr-solid phase interactions, with many of the reactive processes being time dependent. Both sorption and redox reactions impacted Cr(III)- and Cr(VI)-solid phase interactions and were modeled as nonlinear, nonequilibrium or equilibrium, reversible or nonreversible reactive processes. The research investigations within this study highlight the environmental significance of Cr speciation and solid-phase reactivity in heterogeneous subsurface soil systems with contrasting geochemical and mineralogical properties.

54 ENVIRONMENTAL SCIENCES↗

Facilities Condition and Hazards Assessment for Materials and Fuel Complex Facilities MFC-799, 799A, and 770C

The Materials & Fuel Complex (MFC) facilities 799 Sodium Processing Facility (a single building consisting of two areas: the Sodium Process Area (SPA) and the Carbonate Process Area (CPA), 799A Caustic Storage Area, and 770C Nuclear Calibration Laboratory have been declared excess to future Department of Energy mission requirements. Transfer of these facilities from Nuclear Energy to Environmental Management, and an associated schedule for doing so, have been agreed upon by the two offices. The prerequisites for this transfer to occur are the removal of nonexcess materials and chemical inventory, deinventory of the calibration source in MFC-770C, and the rerouting and/or isolation of utility and service systems. This report provides a description of the current physical condition and any hazards (material, chemical, nuclear or occupational) that may be associated with past operations of these facilities. This information will document conditions at time of transfer of the facilities from Nuclear Energy to Environmental Management and serve as the basis for disposition planning. The process used in obtaining this information included document searches, interviews and facility walk-downs. A copy of the facility walk-down checklist is included in this report as Appendix A. MFC-799/799A/770C are all structurally sound and associated hazardous or potentially hazardous conditions are well defined and well understood. All installed equipment items (tanks, filters, etc.) used to process hazardous materials remain in place and appear to have maintained their integrity. There is no evidence of leakage and all openings are properly sealed or closed off and connections are sound. The pits appear clean with no evidence of cracking or deterioration that could lead to migration of contamination. Based upon the available information/documentation reviewed and the overall conditions observed during the facilities walk-down, it is concluded that these facilities may be disposed of at minimal risk to human health, safety or the environment.

99 GENERAL AND MISCELLANEOUS↗

BONDI-HOYLE-LYTTLETON ACCRETION ONTO A PROTOPLANETARY DISK

Young stellar systems orbiting in the potential of their birth cluster can accrete from the dense molecular interstellar medium during the period between the star's birth and the dispersal of the cluster's gas. Over this time, which may span several Myr, the amount of material accreted can rival the amount in the initial protoplanetary disk; the potential importance of this 'tail-end' accretion for planet formation was recently highlighted by Throop and Bally. While accretion onto a point mass is successfully modeled by the classical Bondi-Hoyle-Lyttleton solutions, the more complicated case of accretion onto a star-disk system defies analytic solution. In this paper, we investigate via direct hydrodynamic simulations the accretion of dense interstellar material onto a star with an associated gaseous protoplanetary disk. We discuss the changes to the structure of the accretion flow caused by the disk, and vice versa. We find that immersion in a dense accretion flow can redistribute disk material such that outer disk migrates inward, increasing the inner disk surface density and reducing the outer radius. The accretion flow also triggers the development of spiral density features, and changes to the disk inclination. The mean accretion rate onto the star remains roughly the same with and without the presence of a disk. We discuss the potential impact of this process on planet formation, including the possibility of triggered gravitational instability, inclination differences between the disk and the star, and the appearance of spiral structure in a gravitationally stable system.

79 ASTRONOMY AND ASTROPHYSICS↗

Chemistry and Mineralogy of Outcrops at Meridiani Planum

Analyses of outcrops created by the impact craters Endurance, Fram and Eagle reveal the broad lateral continuity of chemical sediments at the Meridiani Planum exploration site on Mars. Approximately ten mineralogical components are implied in these salt-rich silicic sediments, from measurements by instruments on the Opportunity rover. Compositional trends in an apparently intact vertical stratigraphic sequence at the Karatepe West ingress point at Endurance crater are consistent with non-uniform deposition or with subsequent migration of mobile salt components, dominated by sulfates of magnesium. Striking variations in Cl and enrichments of Br, combined with diversity in sulfate species, provide further evidence of episodes during which temperatures, pH, and water to rock ratios underwent significant change. To first order, the sedimentary sequence examined to date is consistent with a uniform reference composition, modified by movement of major sulfates upward and of minor chlorides downward. This reference composition has similarities to martian soils, supplemented by sulfate anion and the alteration products of mafic igneous minerals. Lesser cementation in lower stratigraphic units is reflected in decreased energies for grinding with the Rock Abrasion Tool. Survival of soluble salts in exposed outcrop is most easily explained by absence of episodes of liquid H2O in this region since the time of crater formation.

Clark, B. C.↗

Biomolecule Sequencer: Next-Generation DNA Sequencing Technology for In-Flight Environmental Monitoring, Research, and Beyond

On the International Space Station (ISS), technologies capable of rapid microbial identification and disease diagnostics are not currently available. NASA still relies upon sample return for comprehensive, molecular-based sample characterization. Next-generation DNA sequencing is a powerful approach for identifying microorganisms in air, water, and surfaces onboard spacecraft. The Biomolecule Sequencer payload, manifested to SpaceX-9 and scheduled on the Increment 4748 research plan (June 2016), will assess the functionality of a commercially-available next-generation DNA sequencer in the microgravity environment of ISS. The MinION device from Oxford Nanopore Technologies (Oxford, UK) measures picoamp changes in electrical current dependent on nucleotide sequences of the DNA strand migrating through nanopores in the system. The hardware is exceptionally small (9.5 x 3.2 x 1.6 cm), lightweight (120 grams), and powered only by a USB connection. For the ISS technology demonstration, the Biomolecule Sequencer will be powered by a Microsoft Surface Pro3. Ground-prepared samples containing lambda bacteriophage, Escherichia coli, and mouse genomic DNA, will be launched and stored frozen on the ISS until experiment initiation. Immediately prior to sequencing, a crew member will collect and thaw frozen DNA samples, connect the sequencer to the Surface Pro3, inject thawed samples into a MinION flow cell, and initiate sequencing. At the completion of the sequencing run, data will be downlinked for ground analysis. Identical, synchronous ground controls will be used for data comparisons to determine sequencer functionality, run-time sequence, current dynamics, and overall accuracy. We will present our latest results from the ISS flight experiment the first time DNA has ever been sequenced in space and discuss the many potential applications of the Biomolecule Sequencer for environmental monitoring, medical diagnostics, higher fidelity and more adaptable Space Biology Human Research Program investigations, and even life detection experiments for astrobiology missions.

Sequencer↗

Meteorological Inventory of Rain-On-Snow Events in the Canadian Arctic Archipelago and Satellite Detection Assessment Using Passive Microwave Data

The spatial and temporal distributions of rain-on-snow (ROS) events across the Canadian Arctic Archipelago (CAA) remain poorly understood owing to their sporadic nature in time and space. This situation motivated the development of remote sensing detection algorithms. This paper uses a large meteorological dataset across the CAA to adapt an existing ROS-detection algorithm developed in a previous study by our group. Results highlight the spatial distribution and evolution of ROS occurrences reported since 1985 at 14 weather stations across the CAA. Results show that >600 ROS events were inventoried since 1985, for which >70% were classified as pure rain (liquid form) and 30% as mixed precipitation (solid/liquid). Of the pure rain events, 75% occurred during spring, 14% during fall, 8% during summer and <1% during winter. Such events can have significant impacts on ungulate grazing conditions through the creation of ice layers, causing serious problems for caribou calf survival, especially during the migration period. This paper introduces an adaptation for larger scale Arctic application of a detection algorithm (sensitivity analysis on the detection threshold) with an error of ~5%. The validation, however, remains limited due to a short study period and limited number of sites.

Canadian Arctic Archipelago (CAA)↗

Ozone, Tropospheric

In the early part of the 20th century, ground-based and balloon-borne measurements discovered that most of atmosphere's ozone is located in the stratosphere with highest concentrations located between 15 and 30 km (9,3 and 18.6 miles). For a long time, it was believed that tropospheric ozone originated from the stratosphere and that most of it was destroyed by contact with the earth's surface. Ozone, O3, was known to be produced by the photo-dissociation of molecular oxygen, O2, a process that can only occur at wavelengths shorter than 242 nm. Because such short-wave-length radiation is present only in the stratosphere, no tropospheric ozone production is possible by this mechanism. In the 1940s, however, it became obvious that production of ozone was also taking place in the troposphere. The overall reaction mechanism was eventually identified by Arie Haagen-Smit of the California Institute of Technology, in highly polluted southern California. The copious emissions from the numerous cars driven there as a result of the mass migration to Los Angeles after World War 2 created the new unpleasant phenomenon of photochemical smog, the primary component of which is ozone. These high levels of ozone were injuring vegetable crops, causing women's nylons to run, and generating increasing respiratory and eye-irritation problems for the populace. Our knowledge of tropospheric ozone increased dramatically in the early 1950s as monitoring stations and search centers were established throughout southern California to see what could be done to combat this threat to human health and the environment.

Fishman, Jack↗

In-situ growth of zinc tungstate nanorods on graphene for enhanced photocatalytic performance

Graphical abstract: Graphene/ZnWO{sub 4} (G–ZnWO{sub 4}) nanorod composite photocatalysts were prepared by a simple one-step method. Namely, the reduction of graphene oxide and the growth of ZnWO{sub 4} nanorod occurred simultaneously in one single process. An enhancement in the photocatalytic activities were observed in G–ZnWO{sub 4} composites compared with pure ZnWO{sub 4} under UV light irradiation. - Highlights: • Graphene–ZnWO{sub 4} composite photocatalyst was prepared for the first time. • The as-prepared composite photocatalysts show high activity for dye degradation. • Effect of graphene amount on the photocatalytic activity was investigated. - Abstract: Graphene–zinc tungstate (G–ZnWO{sub 4}) hybrid photocatalysts were prepared by an in-situ growth method in which the reduction of graphene oxide (GO) and the growth of ZnWO{sub 4} crystals occurred simultaneously. The materials were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, UV–vis diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy. The photocatalytic activity was investigated by the degradation of dye methylene blue (MB). An enhancement in the photocatalytic activity was observed for G–ZnWO{sub 4} hybrids compared with pure ZnWO{sub 4} under UV light. This improvement was attributed to the following two reasons: increased migration efficiency of photo-induced electrons and increased adsorption activity for dye molecules. The effect of the amount of graphene on the photocatalytic activity was also investigated. Results showed that there was an optimum amount of 2%.

36 MATERIALS SCIENCE↗

Hero Carbonsafe Phase 2 Project in the Columbia River Basalt Group: Technical Program Overview

The Hermiston, Oregon Basalt CarbonSAFE Phase II project (HERO CarbonSAFE) seeks to accelerate the deployment of commercial carbon dioxide (CO2) storage projects in basaltic rocks. Hermiston is located near the center of the Columbia River Basalt Group (CRBG), which is one of the largest basalt flows in the US. Basalt CO2 storage has potential advantages to conventional saline storage reservoirs including 1. The potential for rapid mineralization of CO2, 2. associated decreases in pressure and CO2 migration risks, 3. reduced long-term monitoring requirements with respect to plume tracking, 4. widespread geographic distribution and, 5. large storage potential due to thickness, porosity, and CO2 interactions with basalt. For locations such as the Pacific Northwest (PNW), Hawaii, Iceland, India and Japan, whose localities are isolated from large sedimentary basins offering conventional saline storage options, basalt may offer the only feasible option for local CO2 storage. However, mineralization/basalt storage still has many uncertainties, as there are limited field-scale assessments of CO2 storage in basalt. There are significant uncertainties hindering the effective implementation of carbon capture utilization and storage (CCUS) in basalt. These include the lack of proven storage capacities, challenges in methodologies for modeling the area of review in igneous formations, limited understanding of mineralization kinetics and timing, and uncertainties in injectivity. Additionally, the domestic availability of specialized services and drilling expertise is constrained, and existing CCUS permitting and regulatory frameworks, originally developed for conventional saline reservoirs, may not adequately address the unique requirements of basalt systems. HERO CarbonSAFE is designed to address major research gaps and uncertainties associated with basalt storage. Specifically, the project will assess the feasibility of CO2 injection in the deep layered basalts of the CRBG, long-term storage (mineralization), practical approaches for large-scale implementation (50+ million metric tons of CO2 over 30 years), lithology-specific risks, and the technoeconomic potential for CO2 storage in basalts.

58 GEOSCIENCES↗

Advanced Energy Harvesting Control Schemes for Marine Renewable Energy Devices

The Advanced Energy Harvesting Control Schemes for Marine Renewable Energy Devices (Project) investigated, analyzed and modeled advanced turbine control schemes with the objective of increasing the energy harvested by hydrokinetic turbines in turbulent flow. Ocean Renewable Power Company (ORPC) implemented and validated a feedforward controller to increase power capture; and applied and tested the controls on ORPC’s RivGen® Power Systems in Igiugig, Alaska. Assessments of performance improvements were made for the RivGen® in the Igiugig environment and for ORPC’s TidGen® Power System in a reference tidal environment. Annualized Energy Production (AEP) and Levelized Cost of Energy (LCOE) improvements associated with implementation of the recommended control methodology were made for the TidGen® Power System in the DOE reference tidal environment. System Performance Advancement (SPA) goals were selected for the project. SPA targets were to improve Power to Weight Ratio (PWR) and system Availability, with the intention of reducing Levelized Cost of Electricity (LCOE). This project focused primarily reducing in PWR. Reductions in PWR of 25.5% were achieved. Reductions of 20.3% in LCOE were achieved. This project evaluated four types of controllers which were tested in simulation, emulation, a laboratory flume, and the field. The adaptive Kω2 controller performs similarly to the non-adaptive version of the same controller and may be useful in tidal channels where the mean velocity is continually evolving. Trends in simulation were largely verified through experiments, which also provided the opportunity to test assumptions about turbine responsiveness and control resilience to varying scales of turbulence. Laboratory experiments provided an essential stepping stone between simulation and implementation on a field-scale turbine. Experiments also demonstrated that using “energy loss” as a metric to differentiate between well-designed controllers operating at an optimal tip-speed ratio set-point is difficult, which anticipated the outcome from field experiments. The clear message is that the feedforward Kω2 controller out-performs the feedback controllers in almost all aspects and modes of evaluation. The controllers proved a substantial improvement over the baseline performance of the TidGen® turbine, in terms of energy capture. The effects of noise-contaminated angular velocity signals were investigated and validated by simulation as an explanation for the performance limitations observed for TidGen® turbine operations in Eastport, Maine. Measurements of loads performed as part of the laboratory testing indicate that there are limited differences in average axial thrust force between control architectures. This suggests that none of the control strategies are likely to substantially affect loads on the turbine support structure. Velocity measurements during the ORPC RivGen® turbine deployment at Igiugig, Alaska, in 2014 were used to assess the variability of the river flow. Results suggest that the river flow is approximately steady, in the mean sense, at any particular location in the river, with random turbulent fluctuations that are around 10% of the mean flow. The mean flow in the center channel of the river is 2.5 m/s, with reductions near the riverbanks and in the shallows. Spectral analysis and lagged correlation results indicate that temporal fluctuations at a given point are dominated by large scale fluctuations, such that measurements at the turbine location are just as useful for inflow control implementation as upstream measurements. At this site, and likely at many other river sites, flow is generally steady at a given location, but flow varies dramatically between locations, particularly laterally across the river. The primary result is that a lateral change in position of a few meters results in changes to flow speed that far exceed the turbulence fluctuations at any given location. The turbulence is dominated by long time scales. Following final system tests, the RivGen® device was submerged and each evaluated controller was tested across a range of gain/set point values and filter configurations for a minimum of 5 minutes, with longer runs attempted for well-performing cases. In addition to testing controllers during the 2015 deployment season, LGL Alaska Research Associates Inc. (LGL) performed a fish monitoring study in compliance with Alaska Department of Fish and Game fisheries habitat permit for the project. During the season, LGL reviewed 10% of 179 one-hour blocks of footage (6 minutes on the hour) and documented a total of over 1200 fish in the vicinity of the RivGen® device, including over 800 salmon smolt and over 350 adult salmon. No evidence of adverse effects including passage delay by upstream migrating salmon was noted. This is an important result for future deployments and has a direct impact on commercial system designs.

16 TIDAL AND WAVE POWER↗

Thermographic Methods of Detecting Insulation Voids in Large Cryogenic Tanks

Four very large (900Kgal) cryogenic liquid hydrogen and oxygen storage tanks at Kennedy Space Center's LC-39 launch pads were constructed in 1965 to support the Apollo/Saturn V Program and continue to support the Space Shuttle Program. These double-walled spherical tanks with powdered insulation in the annular region, have received minimal refurbishment or even inspection over the years. Intrusively inspecting these tanks would mean a significant down time to the program as the cryogenic liquid and the perlite insulation would have to be removed which would be a significant task and long-term schedule disruption. A study of the tanks was performed to determine the extent to which performance and structural information could be revealed without intrusive inspection. Thermal images of the tanks were taken over a variety of environmental conditions to determine the best conditions under which to compare and use thermography as a health monitoring technique as the tanks continue to age. The settling and subsequent compaction of insulation is a serious concern for cryogenic tanks. Comparison of images from the tanks reveals significant variations in the insulation in the annual regions and point to the use of thermography as a way to monitor for insulation migration and possible compaction. These measurements, when combined with mathematical models of historical boil-off data provide key insight to the condition of the vessels. Acceptance testing methods for new tanks, before they are filled with cryogenic commodity (and thereby thermally cycled), are needed and we explore how thermography can be used to accomplish this.

Arens, Ellen↗

Precise Tailoring of Lithium-Ion Transport for Ultralong-Cycling Dendrite-Free All-Solid-State Lithium Metal Batteries

All-solid-state lithium metal batteries can address crucial challenges regarding insufficient battery cycling life and energy density. The demonstration of long-cycling dendrite-free all-solid-state lithium metal batteries requires precise tailoring of lithium-ion transport of solid-state electrolytes (SSEs). Here, in this work, a proof of concept is reported for precise tailoring of lithium-ion transport of a halide SSE, Li 3 InCl 6 , including intragranular (within grains) but also intergranular (between grains) lithium-ion transport. Lithium-ion migration tailoring mechanism in crystals is developed by unexpected enhanced Li, In, and Cl vacancy populations and lower energy barrier for hopping. The lithium-ion transport tailoring mechanism between the grains is determined by the elimination of voids between grains and the formation of unexpected supersonic conducting grain boundaries, boosting the lithium dendrite suppression ability of SSE. Due to boosted lithium-ion conduction and dendrite-suppression ability, the all-solid-state lithium metal batteries coupled with Ni-rich LiNi 0.83 Co 0.12 Mn 0.05 O 2 cathodes and lithium metal anodes demonstrate breakthroughs in electrochemical performance by achieving extremely long cycling life at a high current density of 0.5 C (2000 cycles, 93.7% capacity retention). This concept of precise tailoring of lithium-ion transport provides a cost, time, and energy efficient solution to conquer the remaining challenges in all-solid-state lithium-metal batteries for fast developing electric vehicle markets.

25 ENERGY STORAGE↗