SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This zip file contains reports discussing the use of fiber optics during well 16B(78)-32 stimulation and circulation tests in the summer of 2024. The reports cover the collection of strain rate and temperature change data during these well events. Theory, methods, and initial data visualizations are included in the reports, highlighting the value of these data types.
The second Space Shuttle (STS-2) was launched from the John F. Kennedy Space Center at 1010 EST on November 12, 1981. An instrumented light airplane was used to measure the emitted concentration of Shuttle exhaust products produced during launch. The airplane accomplished 31 passes through and under the exhaust cloud in the 1 hr 45 min immediately following the launch. Measurements included the following: (1) particulate data in the form of a light scattering coefficient obtained from an integrating nephelometer, (2) particulate concentrations and mass concentrations obtained from a spectrometer probe, (3) gaseous HCl and total HCl concentrations obtained from a gas-filter-correlation instrument and a chemiluminescent instrument, respectively, and (4) outside-air temperature and dew-point temperature. These data are presented along with time, altitude, and position for each cloud pass. These data are within the range of values observed during similar measurements made during the first Space Shuttle launch on April 12, 1981.
The oxidative thermal aging of a crosslinked hydroxyl-terminated polybutadiene (HTPB)/isophorone diisocyanate (IPDI) polyurethane rubber was studied at temperatures between 25 C and 125 C. Changes in tensile elongation, mechanical hardening, polymer network properties, density, O2 permeation, and molecular chain dynamics were investigated as a function of age. The techniques used include solvent swelling, detailed modulus profiling, and NMR relaxation measurements. The Arrhenius methodology, which normally assumes a linear extrapolation of high temperature aging data, is critically evaluated by using extensive data superposition and highly sensitive oxygen consumption measurements. Significant curvature in the Arrhenius diagram of these oxidation rates is observed to be similar to previous results found for other rubber materials that have been evaluated by this technique. Preliminary gel/network properties suggest that crosslinking is the dominant process at higher temperatures. The effect on the oxidation rate of the binder when other constituents found in propellants are present, such as ammonium perchlorate, plasticizer and aluminum powder, is presented.
Si3N4 test bars containing additions of BN, B4C, and C, were hot isostatically pressed in Ta cladding at 1900 and 2050 C to 98.9 percent to 99.5 percent theoretical density. Room-temperature strength data on specimens containing 2 wt pct BN and 0.5 wt pct C were comparable to data obtained for Si3N4 sintered with Y2O3, Y2O3 and Al2O3, or ZrO2. The 1370 C strengths were less than those obtained for additions of Y2O3 or ZrO2 but greater than those obtained from a combination of Y2O3 and Al2O3. SEM fractography indicated that, as with other types of Si3N4, room-temperature strength was controlled by processing flaws. The decrease in strength at 1370 C was typical of Si3N4 having an amorphous grain-boundary phase. The primary advantage of nonoxide additions appears to be in facilitating specimen removal from the Ta cladding.
The Fabry-Perot interferometer is a commonly employed instrument for resolving the spectrum of molecular Rayleigh scattered light for the purpose of evaluating flow properties such as gas velocity and temperature. Rayleigh scattered light from a focused laser beam can be directly imaged through a solid Fabry-Perot etalon onto a CCD detector to provide the spectral content of the scattered light. The spatial resolution of the measurements is governed by the locations of interference fringes. The location of the fringes can be changed by altering the etalon?s physical characteristics, such as thickness and index of refraction. For a fused silica solid etalon the physical properties can be adjusted by changing the etalon temperature; hence changing the order of the interference pattern and the physical fringe locations. Controlling the temperature of the etalon can provide for a slow time-response spatial scanning method for this type of etalon system. A custom designed liquid crystal Fabry-Perot (LCFP) can provide for a fast time-response method of scanning the etalon system. Voltage applied to the liquid crystal interface sets the etalon?s properties allowing Rayleigh measurements to be acquired at varying spatial locations across the image of the laser beam over a very short time period. A standard fused silica etalon and a tunable LCFP etalon are characterized to select the system that is best suited for Rayleigh scattering measurements in subsonic and supersonic flow regimes. A frequency-stabilized laser is used to investigate the apparent frequency stability and temperature sensitivity of the etalon systems. Frequency stability and temperature sensitivity data of the fused silica and LCFP etalon systems are presented in this paper, along with measurements of the LCFP etalon?s tuning capabilities. Rayleigh scattering velocity measurements with both etalon systems are presented, in an effort to determine which etalon is better suited to provide optical flow measurements of velocity, temperature, and density.
The Martian atmosphere has many features in common with the terrestrial mesosphere. Both share similar pressure and temperature ranges, and much of the same chemistry operates in each. For example, the radical species H, OH, and H(sub 2)O, which comprise the odd hydrogen family, are of central importance in the catalytic destruction of CO and O(sub 3) in both atmospheres. The inclusion of recent chemical kinetics data, specifically temperature dependent CO(sub 2) absorption cross-sections, into our one dimensional photochemical model of the Martial atmosphere shows that oxidation of CO by odd hydrogen is too efficient. The incorporation of smaller cross sections for CO(sub 2) leads to an enhanced photolysis rate of water vapor, increasing odd hydrogen to the point where the predicted mixing ratio of CO in our model is substantially less than the observed value of 6.5 x 10(sup -4). Interestingly, most photochemical models of the terrestrial mesosphere underestimate the CO and O(sub 3) densities using currently accepted photodissociation and kinetic rate coefficients. This has also been attributed to an overabundance of odd hydrogen in the models. We shall show that agreement between models and observations of CO in the Martian atmosphere as well as of CO and O(sub 3) in the terrestrial mesosphere can be achieved by revising the rate constants for the reactions OH + HO(sub 2) and CO + OH within their published uncertainties. The fact that similar revisions alleviate discrepancies in both the terrestrial and Martian atmospheres warrants a re-evaluation of these key rate constants at the appropriate temperatures and pressures.
Pressure sensitive paints (PSPs) are now used routinely for measuring surface pressures on wind tunnel models at transonic and supersonic Mach numbers. The method utilizes a surface coating containing fluorescent or phosphorescent materials, the brightness of which varies with the local air pressure on the surface. The present paper will summarize PSP activities (in progress and planned) at the NASA Ames Research Center. One of the main accomplishments at NASA Ames has been the development of a PSP measurement system that is production testing capable. This system has been integrated successfully into the large-scale wind tunnel facilities at Ames. There are several problems related to PSP testing which are unique to large-scale wind tunnel testing. The hardware is often difficult to set-up and must operate under harsh conditions (e.g. high pressures and low temperatures). The data acquisition and reduction times need to be kept to a minimum so that the overall wind tunnel productivity is not compromised. The pressure sensitive paints needs to be very robust; the paints must readily adhere to different surfaces with varying geometries and remain functional for long running times. The paint must have well understood, and preferably minimal, temperature sensitivity since fine control of the tunnel temperature is not easily achievable in the larger wind tunnels. In an effort to improve the overall accuracy of the PSP technique, we are currently evaluating some referenced pressure sensitive paints which contain a pressure- independent luminophor in addition to the one which is affected by the surface pressure. The two luminophors are chosen so that their emission wavelengths are somewhat different. Then by taking two 'wind-on' images with either two cameras (with different filters) or one camera with a rotating filter system, the need for 'wind-off' images can be eliminated. The ratio of the two wind-on images accounts for nonuniform lighting and model motion problems (physical movement of the model under aerodynamic loading) are not a concern any more. The paints and data acquisition and reduction software for this type of a PSI system are currently under development and evaluation. Additional information is contained within the original extended abstract.
The environmental aspect of elevated temperature and its relationship to the science of strain gage calibrations of aircraft structures are addressed. A section of a wing designed for a high-speed aircraft structure was used to study this problem. This structure was instrumented with strain gages calibrated at both elevated and room temperatures. Load equations derived from a high-temperature load calibration were compared with equations derived from an identical load calibration at room temperature. The implications of the high temperature load calibration were studied from the viewpoint of applicability and necessity. Load equations derived from the room temperature load calibration resulted in generally lower equation standard errors than equations derived from the elevated temperature load calibration. A distributed load was applied to the structure at elevated temperature and strain gage outputs were measured. This applied load was then calculated using equations derived from both the room temperature and elevated temperature calibration data. It was found that no significant differences between the two equation systems existed in terms of computing this applied distributed load, as long as the thermal shifts resulting from thermal stresses could be identified. This identification requires a heating of the structure. Therefore, it is concluded that for this structure, a high temperature load calibration is not required. However, a heating of the structure is required to determine thermal shifts.
New testing capabilities are needed in order to foster thrust foil air bearing technology development and aid its transition into future Oil-Free gas turbines. This paper describes a new test apparatus capable of testing thrust foil air bearings up to 100 mm in diameter at speeds to 80,000 rpm and temperatures to 650 C (1200 F). Measured parameters include bearing torque, load capacity, and bearing temperatures. This data will be used for design performance evaluations and for validation of foil bearing models. Preliminary test results demonstrate that the rig is capable of testing thrust foil air bearings under a wide range of conditions which are anticipated in future Oil-Free gas turbines. Torque as a function of speed and temperature corroborates results expected from rudimentary performance models. A number of bearings were intentionally failed with no resultant damage whatsoever to the test rig. Several test conditions (specific speeds and loads) revealed undesirable axial shaft vibrations which have been attributed to the magnetic bearing control system and are under study. Based upon these preliminary results, this test rig will be a valuable tool for thrust foil bearing research, parametric studies and technology development.
It is widely believed that the cross-field spatial scale of coronal heating is small, so that the fundamental plasma structures (loop strands) are spatially unresolved. We therefore must appeal to diagnostic techniques that are not strongly affected by spatial averaging. One valuable observable is the emission measure distribution, EM(T), which indicates how much material is present at each temperature. Using data from the Extreme-ultraviolet Imaging Spectrograph on the Hinode mission, we have determined emission measure distributions in the cores of two active regions. The distributions have power law slopes of approximately 2.4 coolward of the peak. We compare these slopes, as well as the amount of emission measure at very high temperature, with the predictions of a series of models. The models assume impulsive heating (nanoflares) in unresolved strands and take full account of non equilibrium ionization. A variety of nanoflare properties and initial conditions are considered. We also comment on the selection of spectral lines for upcoming missions like Solar Orbiter.
Two recent large data releases for the Atacama Cosmology Telescope (ACT), called DR4 and DR5, are available for public access. These data include temperature and polarization maps that cover nearly half the sky at arcminute resolution in three frequency bands; lensing maps and component-separated maps covering ∼2100 deg 2 of sky; derived power spectra and cosmological likelihoods; a catalog of over 4000 galaxy clusters; and supporting ancillary products including beam functions and masks. The data and products are described in a suite of ACT papers; here we provide a summary. In order to facilitate ease of access to these data, we present a set of Jupyter IPython notebooks developed to introduce users to DR4, DR5, and the tools needed to analyze these data. The data products (excluding simulations) and the set of notebooks are publicly available on the NASA Legacy Archive for Microwave Background Data Analysis; simulation products are available on the National Energy Research Scientific Computing Center.
Since the U.S. Department of Energy (DOE)’s Office of Nuclear Energy (NE) initiated the Nuclear Energy University Program (NEUP) in 2009, a total of 30 NEUP projects focused on High-Temperature Gas-cooled Reactor (HTGR) thermal-fluid experiments were funded up to fiscal year (FY) 2021. This represents a total DOE investment of approximately $23M over the 12-year period, covering thermal fluid phenomena important to both pebble bed and prismatic HTGR designs. The NEUP projects have produced a large amount of high-quality experimental and computational data that were published in final project reports, journal articles, dissertations, and conference proceedings, but in most cases the actual data sets and supporting information such as facility and instrumentation descriptions were not publicly disseminated to the HTGR community. To the authors’ best knowledge, a data platform that organizes and summarizes these NEUP-funded projects for HTGR research does not currently exist. To improve access to this HTGR validation data and optimize the return on the significant investment made by DOE, the Advanced Reactor Technologies (ART) Gas-Cooled Reactor (GCR) program started a survey of completed and ongoing HTGR NEUP projects with the aim of developing a public-access data platform that can be used to retrieve computational fluid dynamics (CFD) and system code validation data and guide future NEUP investments. This paper summarizes the status of the current ART-GCR database, provides an overview of the NEUP-funded HTGR-related research projects from FY2009 to FY2021 and identify validation knowledge gaps still existing in HTGR thermal-fluid research.
This public data set contains openly-documented, machine readable digital research data corresponding to figures published in G.M. Bodner et al., ‘Initial Characterization of Electron Temperature and Density Profiles in PEGASUS Spherical Tokamak Discharges Driven Solely by Local Helicity Injection,’ Physics of Plasmas 28, 102504 (2021) and its erratum in Physics of Plasmas 31, 129904 (2024).
Work accomplished includes: Beta delivery 1 of the MODIS LST product; the first version of MODIS LST ATBD; update of the atmospheric radiative transfer code ATRAD; the development of a new approach look-up table method; and improvement of the TIR spectrometer. Preliminary feasibility analysis of the look-up table approach is presented in terms of showing the effects on the TIR radiance at the top of the atmosphere of the stratospheric and upper atmospheric temperature profiles, the surface emissivity and temperature, the lower atmospheric temperature and water vapor profiles, and the viewing angle.
A charging station (CS) and its associated electric vehicle supply equipment (EVSE) and charging electric vehicle (EV) interactions are potential targets for data falsification attacks since CSs are typically unmanned public facilities that are connected to the internet and EVs incorporate the vulnerable CAN bus network, which are both susceptible to remote attacks. The research question being addressed is how is the EV owner and CS negatively affected by CAN bus EV battery current sensor and battery temperature sensor data falsification attacks. Negative effects include economic losses from reduced life span of the battery, battery thermal runaway and fire (and potential loss of surrounding structure), and reduced utilization of the CS due to delayed departure time (longer charging times).
Two recent large data releases for the Atacama Cosmology Telescope (ACT), called DR4 and DR5, are available for public access. These data include temperature and polarization maps that cover nearly half the sky at arcminute resolution in three frequency bands; lensing maps and component-separated maps covering ~ 2,100 deg 2 of sky; derived power spectra and cosmological likelihoods; a catalog of over 4,000 galaxy clusters; and supporting ancillary products including beam functions and masks. The data and products are described in a suite of ACT papers; here we provide a summary. In order to facilitate ease of access to these data we present a set of Jupyter IPython notebooks developed to introduce users to DR4, DR5, and the tools needed to analyze these data. The data products (excluding simulations) and the set of notebooks are publicly available on the NASA Legacy Archive for Microwave Background Data Analysis (LAMBDA); simulation products are available on the National Energy Research Scientific Computing Center (NERSC).
The location, timing, and intermittency of precipitation in California make the state integrally reliant on winter-season snowpack accumulation to maintain its economic and agricultural livelihood. Of particular concern is that winter-season snowpack has shown a net decline across the western United States over the past 50 years, resulting in major uncertainty in water-resource management heading into the next century. Cutting-edge tools are available to help navigate and preemptively plan for these uncertainties. This paper uses a next-generation modeling technique-variable-resolution global climate modeling within the Community Earth System Model (VR-CESM)-at horizontal resolutions of 0.125° (14 km) and 0.25° (28 km). VR-CESM provides the means to include dynamically large-scale atmosphere-ocean drivers, to limit model bias, and to provide more accurate representations of regional topography while doing so in a more computationally efficient manner than can be achieved with conventional general circulation models. This paper validates VR-CESM at climatological and seasonal time scales for Sierra Nevada snowpack metrics by comparing them with the "Daymet," "Cal-Adapt," NARR, NCEP, and North American Land Data Assimilation System (NLDAS) reanalysis datasets, the MODIS remote sensing dataset, the SNOTEL observational dataset, a standard-practice global climate model (CESM), and a regional climate model (WRF Model) dataset. Overall, given California's complex terrain and intermittent precipitation and that both of the VR-CESM simulations were only constrained by prescribed sea surface temperatures and data on sea ice extent, a 0.68 centered Pearson product-moment correlation, a negative mean SWE bias of < 7 mm, an interquartile range well within the values exhibited in the reanalysis datasets, and a mean December-February extent of snow cover that is within 7% of the expected MODIS value together make apparent the efficacy of the VR-CESM framework.
Vertical profiles of atmospheric ozone have been measured for a number of years by WFF personnel using small balloon borne ozonesondes. These sondes are interfaced with meteorological radiosondes so that both ozone data and meterological data (pressure, temperature, humidity, wind speed and direction) are obtained from ground level up to 30 to 35 km. Efforts at Wallops have been focused in three areas. The first involves biweekly launches from two sites (Wallops and Natal, Brazil), timed to coincide with overpasses of satellite borne ozone sensors such as the Solar Backscattered Ultraviolet. The resulting data are reported to the World Ozone Data Center and are used for satellite correlative support, as well as, for studies of both tropospheric and stratospheric ozone. The second activity consists of field campaigns in remote locations in support of special projects. The third is a continuing activity to quantitatively evaluate and improve the sonde's performance under stratospheric conditions.