Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Soil Temperature and Moisture Profile (STAMP) System Handbook

The soil temperature and moisture profile system (STAMP) provides vertical profiles of soil temperature, soil water content (soil-type specific and loam type), plant water availability, soil conductivity, and real dielectric permittivity as a function of depth below the ground surface at half-hourly intervals, and precipitation at one-minute intervals. The profiles are measured directly by in situ probes at all extended facilities of the SGP climate research site. The profiles are derived from measurements of soil energy conductivity. Atmospheric scientists use the data in climate models to determine boundary conditions and to estimate the surface energy flux. The data are also useful to hydrologists, soil scientists, and agricultural scientists for determining the state of the soil. The STAMP system replaced the SWATS system in early 2016.

54 ENVIRONMENTAL SCIENCES↗

Growth Optimization and Device Integration of Narrow‐Bandgap Graphene Nanoribbons

Abstract The electronic, optical, and magnetic properties of graphene nanoribbons (GNRs) can be engineered by controlling their edge structure and width with atomic precision through bottom‐up fabrication based on molecular precursors. This approach offers a unique platform for all‐carbon electronic devices but requires careful optimization of the growth conditions to match structural requirements for successful device integration, with GNR length being the most critical parameter. In this work, the growth, characterization, and device integration of 5‐atom wide armchair GNRs (5‐AGNRs) are studied, which are expected to have an optimal bandgap as active material in switching devices. 5‐AGNRs are obtained via on‐surface synthesis under ultrahigh vacuum conditions from Br‐ and I‐substituted precursors. It is shown that the use of I‐substituted precursors and the optimization of the initial precursor coverage quintupled the average 5‐AGNR length. This significant length increase allowed the integration of 5‐AGNRs into devices and the realization of the first field‐effect transistor based on narrow bandgap AGNRs that shows switching behavior at room temperature. The study highlights that the optimized growth protocols can successfully bridge between the sub‐nanometer scale, where atomic precision is needed to control the electronic properties, and the scale of tens of nanometers relevant for successful device integration of GNRs.

36 MATERIALS SCIENCE↗

High field electron paramagnetic resonance spectroscopy under ultrahigh vacuum conditions—A multipurpose machine to study paramagnetic species on well defined single crystal surfaces

A new ultrahigh vacuum (UHV) electron paramagnetic resonance (EPR) spectrometer operating at 94 GHz to investigate paramagnetic centers on single crystal surfaces is described. It is particularly designed to study paramagnetic centers on well-defined model catalysts using epitaxial thin oxide films grown on metal single crystals. The EPR setup is based on a commercial Bruker E600 spectrometer, which is adapted to ultrahigh vacuum conditions using a home made Fabry Perot resonator. The key idea of the resonator is to use the planar metal single crystal required to grow the single crystalline oxide films as one of the mirrors of the resonator. EPR spectroscopy is solely sensitive to paramagnetic species, which are typically minority species in such a system. Hence, additional experimental characterization tools are required to allow for a comprehensive investigation of the surface. The apparatus includes a preparation chamber hosting equipment, which is required to prepare supported model catalysts. In addition, surface characterization tools such as low energy electron diffraction (LEED)/Auger spectroscopy, temperature programmed desorption (TPD), and infrared reflection absorption spectroscopy (IRAS) are available to characterize the surfaces. A second chamber used to perform EPR spectroscopy at 94 GHz has a room temperature scanning tunneling microscope attached to it, which allows for real space structural characterization. The heart of the UHV adaptation of the EPR experiment is the sealing of the Fabry-Perot resonator against atmosphere. To this end it is possible to use a thin sapphire window glued to the backside of the coupling orifice of the Fabry Perot resonator. With the help of a variety of stabilization measures reducing vibrations as well as thermal drift it is possible to accumulate data for a time span, which is for low temperature measurements only limited by the amount of liquid helium. Test measurements show that the system can detect paramagnetic species with a density of approximately 5 × 10{sup 11} spins/cm{sup 2}, which is comparable to the limit obtained for the presently available UHV-EPR spectrometer operating at 10 GHz (X-band). Investigation of electron trapped centers in MgO(001) films shows that the increased resolution offered by the experiments at W-band allows to identify new paramagnetic species, that cannot be differentiated with the currently available methodology.

36 MATERIALS SCIENCE↗

Experimental and Theoretical Structural Investigation of AuPt Nanoparticles Synthesized using a Direct Electrochemical Method

In this report we examine the structure of bimetallic nanomaterials prepared by an electrochemical approach known as hydride-terminated (HT) electrodeposition. It has been shown previously that this method can lead to deposition of a single Pt monolayer on bulk-phase Au surfaces. Specifically, under appropriate electrochemical conditions and using a solution containing PtCl 4 2- , a monolayer of Pt atoms electrodeposits onto bulk-phase Au immediately followed by a monolayer of H atoms. The H-atom capping layer prevents deposition of Pt multilayers. We applied this method to ~1.6 nm Au nanoparticles (AuNPs) immobilized on an inert electrode surface. In contrast to the well-defined, segregated Au/Pt structure of the bulk-phase surface, we observe that HT electrodeposition leads to the formation of AuPt quasi-random alloy NPs rather than the core@shell structure anticipated from earlier reports relating to deposition onto bulk phases. The results provide a good example of how the phase behavior of macro materials does not always translate to the nano world. A key component of this study was the structure determination of the AuPt NPs, which required a combination of electrochemical methods, electron microscopy, X-ray absorption spectroscopy, and theory (DFT and MD).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluation of Stratocumulus Evolution Under Contrasting Temperature Advections in CESM2 Through a Lagrangian Framework

Abstract This study leveraged a Lagrangian framework to examine the evolution of stratocumulus clouds under cold and warm advections (CADV and WADV) in the Community Earth System Model 2 (CESM2) against observations. We found that CESM2 simulates a too rapid decline in low‐cloud fraction (LCF) and cloud liquid water path (CLWP) under CADV conditions, while it better aligns closely with observed LCF under WADV conditions but overestimates the increase in CLWP. Employing an explainable machine learning approach, we found that too rapid decreases in LCF and CLWP under CADV conditions are related to overestimated drying effects induced by sea surface temperature, whereas the substantial increase in CLWP under WADV conditions is associated with the overestimated moistening effects due to free‐tropospheric moisture and surface winds. Our findings suggest that overestimated drying effects of sea surface temperature on cloud properties might be one of crucial causes for the high equilibrium climate sensitivity in CESM2.

54 ENVIRONMENTAL SCIENCES↗

Kinetic and Mechanistic Understanding of Boron-Containing Catalysts for the Production of Light Olefins through Selective Oxidation

In recent years, an abundance of natural gas obtained from shale deposits has created opportunities for the US chemical industry to establish new and more efficient processes for the production of chemical intermediates and polymers. For example, the replacement of petroleum-derived naphtha as a to shale-derived ethane as feedstocks has made the production of ethylene/polyethylene less costly. However, this shift in feedstock has led to lower production of propylene from steam crackers, and new “on-purpose” light olefin production technologies have been implemented to bridge the gap between propylene supply and demand. The most important of these processes is direct propane dehydrogenation (PDH), but catalyst deactivation and high temperatures lead to high capital and operating costs. Oxidative dehydrogenation of propane (ODHP) is an efficient alternative to PDH, but high selectivity to CO2 from previous metal oxide catalyst prevents implementation. Hexagonal boron nitride (hBN) and other boron-containing materials have been recently developed as highly selective catalysts for both ODHP and oxidative cracking, surpassing previous systems. Much is still unknown in regard to the mechanism and the dynamic surface changes that occur under reaction conditions. This research project aims to combine in situ/operando spectroscopic investigation and kinetic studies to elucidate the interplay between the proposed gas-phase mechanism and the surface structures on the working catalyst. These insights will be leveraged to create a framework for optimizing reaction conditions and material synthesis for the next generation of boron-containing selective oxidation catalysts.

02 PETROLEUM↗

Direct Mapping of Charge Distribution during Lithiation of Ge Nanowires Using Off-Axis Electron Holography

The successful operation of rechargeable batteries relies on reliable insertion/ extraction of ions into/from the electrodes. The battery performance and the response of the electrodes to such ion insertion and extraction are directly related to the spatial distribution of the charge and its dynamic evolution. However, it remains unclear how charge is distributed in the electrodes during normal battery operation. In this work, we have used offaxis electron holography to measure charge distribution during lithium ion insertion into a Ge nanowire (NW) under dynamic operating conditions. We discovered that the surface region of the Ge core is negatively charged during the core-shell lithiation of the Ge NW, which is counterbalanced by positive charge on the inner surface of the lithiated LixGe shell. The remainder of the lithiated LixGe shell is free from net charge, consistent with its metallic characteristics. The present work provides a vivid picture of charge distribution and dynamic evolution during Ge NW lithiation and should form the basis for tackling the response of these and related materials under real electrochemical conditions.

25 ENERGY STORAGE↗

Pelleting of Pine and Switchgrass Blends: Effect of Process Variables and Blend Ratio on the Pellet Quality and Energy Consumption

The blending of woody and herbaceous biomass can influence pellet quality and the energy consumption of the process. This work aims to understand the pelleting characteristics of 2-inch top-pine residue blended with switchgrass at high moisture content. The process variables tested are blend moisture content, length-to-diameter (L/D) ratio in the pellet die, and the blend ratio. A flat die pellet mill was also used in this study. The pine and switchgrass blend ratios that were tested include: (1) 25% 2-inch top pine residue with 75% switchgrass; (2) 50% 2-inch top pine residue with 50% switchgrass; and (3) 75% 2-inch top pine residue with 25% switchgrass. The pelleting process conditions tested included the L/D ratio in the pellet die (i.e., 1.5 to 2.6) and the blend moisture content (20 to 30%, w.b.). Analysis of experimental data indicated that blending 25% switchgrass with 75% 2-inch top pine residue and 50% switchgrass with 50% 2-inch top pine residue resulted in pellets with a bulk density of > 550 kg/m3 and durability of > 95%. Optimization of the response surface models developed for process conditions in terms of product properties indicated that a higher L/D ratio of 2.6 and a lower blend-moisture content of 20% (w.b.) maximized bulk density and durability. Higher pine in the blends improved the pellet durability and reduced energy consumption.

09 BIOMASS FUELS↗

Numerical Analysis of JNES Seismic Tests on Degraded Combined Piping System

Nuclear power plant safety under seismic conditions is an important consideration. The piping systems may have some defects caused by fatigue, stress corrosion cracking, etc., in aged plants. These cracks may not only affect the seismic response but also grow and break through causing loss of coolant. Therefore, an evaluation method needs to be developed to predict crack growth behavior under seismic excitation. This paper describes efforts conducted to analyze and better understand a series of degraded pipe tests under seismic loading that was conducted by Japan Nuclear Energy Safety Organization (JNES). A special 'cracked-pipe element' (CPE) concept, where the element represented the global moment-rotation response due to the crack, was developed. This approach was developed to significantly simplify the dynamic finite element analysis in fracture mechanics fields. In this paper, model validation was conducted by comparisons with a series of pipe tests with circumferential through-wall and surface cracks under different excitation conditions. These analyses showed that reasonably accurate predictions could be made using the abaqus connector element to model the complete transition of a circumferential surface crack to a through-wall crack under cyclic dynamic loading. The JNES primary loop recirculation piping test was analyzed in detail. This combined-component test had three crack locations and multiple applied simulated seismic block loadings. Comparisons were also made between the ABAQUS finite element (FE) analyses results to the measured displacements in the experiment. Good agreement was obtained, and it was confirmed that the simplified modeling is applicable to a seismic analysis for a cracked pipe on the basis of fracture mechanics. Pipe system leakage did occur in the JNES tests. The analytical predictions using the CPE approach did not predict leakage, suggesting that cyclic ductile tearing with large-scale plasticity was not the crack growth mode for the acceleration excitations considered here. Hence, the leakage was caused by low-cycle fatigue with small-scale yielding. The procedure used to make predictions of low-cycle fatigue crack growth with small-scale yielding was based on the Dowling {Delta}J procedure, which is an extension of linear-elastic fatigue crack growth methodology into the nonlinear plasticity region. The predicted moments from the CPE approach were used using a cycle-by-cycle crack growth procedure. The predictions compare quite well with the experimental measurements.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

High-peak-power surface high-harmonic generation at extreme ultra-violet wavelengths from a tape

Solid-based surface high-harmonic generation from a tape is experimentally studied. By operating at mildly relativistic normalized laser strengths a{sub 0}≲0.2, harmonics up to the 17th order are efficiently produced in the coherent wake emission (CWE) regime. CWE pulse properties, such as divergence, energy, conversion efficiency, and spectrum, are investigated for various tape materials and drive laser conditions. A clear correlation between surface roughness and harmonic beam divergence is found. At the measured pulse properties for the 15th harmonic (conversion efficiency ∼6.5×10{sup −7}, divergence ∼7−15 mrad), the 100-mJ-level drive laser produces several MWs of extreme ultra-violet pulses. The spooling tape configuration enables multi-Hz operation over thousands of shots, making this source attractive as a seed to the few-Hz laser-plasma-accelerator-driven free-electron laser (FEL). Models indicate that these CWE pulses with MW level powers are sufficient for seed-induced bunching and FEL gain.

36 MATERIALS SCIENCE↗

Effect of Channel Configurations for Tritium Transfer in Printed Circuit Heat Exchangers

The Next Generation Nuclear Plant (NGNP), a very High temperature Gas-Cooled Reactor (VHTR) concept, will provide the first demonstration of a closed-loop Brayton cycle at a commercial scale of a few hundred megawatts electric and hydrogen production. The power conversion system (PCS) for the NGNP will take advantage of the significantly higher reactor outlet temperatures of the VHTR to provide higher efficiencies than can be achieved in the current generation of light water reactors. Besides demonstrating a system design that can be used directly for subsequent commercial deployment, the NGNP will demonstrate key technology elements that can be used in subsequent advanced power conversion systems for other Generation IV reactors. In anticipation of the design, development and procurement of an advanced power conversion system for the NGNP, the system integration of the NGNP and hydrogen plant was initiated to identify the important design and technology options that must be considered in evaluating the performance of the proposed NGNP. In the VHTR system, an intermediate heat exchanger (IHX), which transfers heat from the reactor core to the electricity or hydrogen production system is one key component, and its effectiveness is directly related to the system overall efficiency. In the VHTRs, the gas fluids used for coolant generally have poor heat transfer capability, so it requires very large surface area for a given condition. For this reason, a compact heat exchanger (CHE), which is widely used in industry especially for gasto-gas or gas-to-liquid heat exchange is considered as a potential candidate for an IHX replacing the classical shell and tube type heat exchanger. A compact heat exchanger is arbitrary referred to be a heat exchanger having a surface area density greater than 700 m2/m3. The compactness is usually achieved by fins and micro-channels, and leads to the enormous heat transfer enhancement and size reduction. The surface area density is the total heat transfer area divided by the volume of the heat exchanger. In the case of PCHE units, the heat transfer surface area density may be as high as 2,500 m2/m3. This high compactness implies an appreciable reduction in material reducing cost. In this study, heat transfer and tritium penetration analyses have been performed for two different channel configurations of the PCHE; (1) standard and (2) off-set. One of the goals of this study was to determine whether offsetting the hot and cold streams would significantly reduce the tritium flux, and whether or not it would affect the heat transfer significantly.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A smeared crack modeling framework accommodating multi-directional fracture at finite strains

A generic smeared crack modeling framework predicated on the deformation gradient decomposition (DGD) approach is proposed for use in dynamic fracture problems at finite strains, accommodating failure along multiple mutually orthogonal fracture planes embedded within an independently defined bulk material model. Within this constitutive framework, the traction equilibrium conditions imposed at each failure surface are used to determine the associated crack displacements stored as internal state variables. In general, the enforcement of interfacial equilibrium entails the implicit solution of a non-linear system of equations within the constitutive update procedure. However, if inertial effects arising due to the relative motion of the fractured material are incorporated within the model, the traction equilibrium conditions are shown to give rise to corresponding dynamic equations of motion governing the time-evolution of the crack opening displacements. For dynamic problems, an explicit time-integration procedure is devised to efficiently update the material state, subject to a set of internal frictionless contact constraints to prevent material inversion. Finally, the efficacy of the proposed modeling framework is investigated through several benchmark dynamic fracture problems run within the explicit finite element code DYNA3D.

42 ENGINEERING↗

Scanning tunneling spectroscopy of surface-oxidized Gallium-stabilized δ -phase plutonium

Here, the first contiguous experimental scanning tunneling spectroscopy (STS) measurements of the electronic structure of a plutonium (Pu) surface are presented and compared to current theoretical results. The experiments took place under UHV conditions, for which Pu is known to retain a native surface oxide. The STS data shows that no band gap is observable at room temperature. Theoretical calculations predict that bulk Pu oxides are semiconductors, but the spectral results for the cleaned Pu surface native oxide under UHV conditions could be better characterized as that of a semimetal.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Wall conditioning effects of boron powder injection in KSTAR with a tungsten divertor

Boron powder dropped into KSTAR plasmas decreased the radiated power, core electron density, and Z eff , indicating that the ablated and redeposited boron powder helped to condition the plasma-facing surfaces. Visible line emission of oxygen and tungsten were also reduced by 50% (80%) with boron injection into H-mode (L-mode) discharges that used the new KSTAR tungsten monoblock lower divertor. Dynamic particle balance analysis found a negligible difference in the inferred wall pumping rate during the steady portion of the discharges. It is inferred that the observed conditioning effects were principally caused by a reduction in intrinsic impurities as opposed to a reduction in wall recycling. These results are in qualitative agreement with low-Z injected powder experiments across many fusion devices, confirming the utility of low-Z powder injection as a real-time wall conditioning tool.

boron powder injection↗

Identifying and Tuning the In Situ Oxygen-Rich Surface of Molybdenum Nitride Electrocatalysts for Oxygen Reduction

Rigorous in situ studies of electrocatalysts are required to enable the design of higher performing materials. Nonplatinum group metals for oxygen reduction reaction (ORR) catalysis containing light elements such as O, N, and C are known to be susceptible to both ex situ and in situ oxidation, leading to challenges associated with ex situ characterization methods. We have previously shown that the bulk O content plays an important role in the activity and selectivity of Mo–N catalysts, but further understanding of the role of composition and morphological changes at the surface is needed. Here, we report the measurement of in situ surface changes to a molybdenum nitride (MoN) thin film under ORR conditions using grazing incidence X-ray absorption and reflectivity. We show that the half-wave potential of MoN can be improved by ~90 mV by potential conditioning up to 0.8 V versus RHE. Utilizing electrochemical analysis, dissolution monitoring, and surface-sensitive X-ray techniques, we show that under moderate polarization (0.3–0.7 V vs RHE) there is local ligand distortion, O incorporation, and amorphization of the MoN surface, without changes in roughness. Furthermore, with a controlled potential hold procedure, we show that the surface changes concurrent with potential conditioning are stable under ORR relevant potentials. Conversely, at higher potentials (≥0.8 V vs RHE), the film incorporates O, dissolves, and roughens, suggesting that in this higher potential regime, the performance enhancements are due to increased access to active sites. Density functional theory calculations and Pourbaix analysis provide insights into film stability and O incorporation as a function of potential. These findings coupled with in situ electrochemical surface-sensitive X-ray techniques demonstrate an approach to studying nontraditional surfaces in which we can leverage our understanding of surface dynamics to improve performance with the rational, in situ tuning of active sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dynamic Interaction of Nitrogen Atoms with the Surface of an Aluminum Crystal

A possibility of reconstructing the ion-atom dynamic interaction potential from the dependence of the rainbow scattering angle of nitrogen atoms under the conditions of grazing incidence on the surface of an aluminum crystal on the total kinetic energy of the accelerated atomic particles is demonstrated. The parameters of the dynamic interaction potential are determined within the energy range from 10 to 70 keV using the best possible fit between the calculated dependence of the rainbow scattering angle on the energy of the particles incident on the aluminum crystal surface along the crystallographic directions and the available experimental data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Simulation and analysis of slip flow of water at hydrophobic silica surfaces of nanometer slit pores

Water flow in nanopores is controlled fundamentally by pore wettability and interfacial water features. In the research herein reported, Molecular dynamics (MD) was used to simulate water flow in nanometer slit pores of silica surfaces with variable wetting characteristics. Compared to Couette flow, the simulated slit-pores of the talc (001) and octadecyltrichlorosilane (OTS) monolayer surfaces exhibited water flow enhancement and a positive slip length at the interface, whereas water flow velocity at the quartz (001) and amorphous silica surfaces was zero, adhering to the no slip condition. More intensive interactions between the interfacial water and hydrophilic silica surfaces were confirmed by MD simulation and sum-frequency vibrational spectroscopy (SFVS) results. A water exclusion zone of approximately 3 Å was found at the hydrophobic silica surfaces by quantitative MD interfacial water analysis and validated by SFVS. This exclusion zone dimension was similar in magnitude to the slip length (4–5 Å) as determined from simulated water flow in hydrophobic silica slit pores. The simulated slip lengths at the hydrophobic surfaces (0.2–1 nm) were significantly less than the experimental slip lengths (>40 nm) reported in the literature. In the case of the experimental results, this difference appears to be due to nanobubbles expected to be present at hydrophobic surfaces.

42 ENGINEERING↗

Computational and Experimental Validation of Fractal-Fin, Dimpled Solar Heat Collector

A 3 foot x 3 foot x 3 foot aluminum solar collector was manufactured using computer numerical control. The interior of the device included six triangular dimpled fins for enhanced heat transfer. The interior vertical wall on the south side was also dimpled. The solar collector working fluid was based on water, and the collector consisted solely of passive heat transfer mechanisms (no moving parts), making it ideal for off-the-grid and rural applications. Two types of heat transfer experiments were conducted. One experiment had external flat heaters attached on the top and the front side, while the other four sides were insulated. Except for the bottom surface, the second experiment had all its exterior surfaces sprayed with black solar paint to collect as much solar heat as possible. Temperature data as a function of time was collected using 14 thermocouples spread strategically throughout the solar collector. In addition, computational fluid dynamics (CFD) simulations were conducted using the dynamic Smagorinsky large eddy simulation turbulence model. The first simulation considered that both the top and front surfaces were exposed to a fixed temperature of 313.7 K (105 °F), while the remaining four surfaces were insulated. For the second simulation, all conditions were the same, except that the temperature for both heated surfaces was raised to 350 K (170.3 °F). The two temperatures are expected to bound the solar collector operational temperature during the late- Spring, Summer, and early-Fall months. The solar collector design, experimental data, CFD output, and a discussion of five manufacturing approaches and costs are documented in this report.

14 SOLAR ENERGY↗