Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “process loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Water Flow Testing and Unsteady Pressure Analysis of a Two-Bladed Liquid Oxidizer Pump Inducer

The unsteady fluid dynamic performance of a cavitating two-bladed oxidizer turbopump inducer was characterized through sub-scale water flow testing. While testing a novel inlet duct design that included a cavitation suppression groove, unusual high-frequency pressure oscillations were observed. With potential implications for inducer blade loads, these high-frequency components were analyzed extensively in order to understand their origins and impacts to blade loading. Water flow testing provides a technique to determine pump performance without the costs and hazards associated with handling cryogenic propellants. Water has a similar density and Reynolds number to liquid oxygen. In a 70%-scale water flow test, the inducer-only pump performance was evaluated. Over a range of flow rates, the pump inlet pressure was gradually reduced, causing the flow to cavitate near the pump inducer. A nominal, smooth inducer inlet was tested, followed by an inlet duct with a circumferential groove designed to suppress cavitation. A subsequent 52%-scale water flow test in another facility evaluated the combined inducer-impeller pump performance. With the nominal inlet design, the inducer showed traditional cavitation and surge characteristics. Significant bearing loads were created by large side loads on the inducer during synchronous cavitation. The grooved inlet successfully mitigated these loads by greatly reducing synchronous cavitation, however high-frequency pressure oscillations were observed over a range of frequencies. Analytical signal processing techniques showed these oscillations to be created by a rotating, multi-celled train of pressure pulses, and subsequent CFD analysis suggested that such pulses could be created by the interaction of rotating inducer blades with fluid trapped in a cavitation suppression groove. Despite their relatively low amplitude, these high-frequency pressure oscillations posed a design concern due to their sensitivity to flow conditions and test scale. The amplitude and frequency of oscillations varied considerably over the pump s operating space, making it difficult to predict blade loads.

Schwarz, Jordan B.↗
DOE OSTI2023

Infusible Thermoplastic Composites for Wind Turbine Blade Manufacturing: Fatigue Life of Thermoplastic Laminates under Ambient and Low-Temperature Conditions

Traditionally, thermoset resins such as polyesters (PE) and epoxies are used as the polymer matrix for construction of wind turbine blades. However, concern about their end-of-life treatment garners interest to use thermoplastics for increased recyclability. However, the high viscosity of molten thermoplastics inhibits their use in manufacturing wind turbine blades with injection or compression molding. A recently developed, infusible, reactive thermoplastic resin overcomes this technological barrier. Toward verifying that this recyclable resin is suitable for use in wind turbine blades, a dataset of R?=?0.1 and R?=?10 fatigue data for glass fiber-reinforced acrylic composites is provided and equal fatigue life to industry standard epoxy and unsaturated PE resin systems is demonstrated. Specifically, R?=?0.1 fatigue data for acrylic composites at room temperature and -30?degrees C for verification of low-temperature performance are tabulated. To elucidate failure mechanisms, in situ mechanical testing with X-ray computed tomography demonstrates that damage accumulation occurs by crack propagation along the fiber-matrix interface under cyclic loading. Infrared (IR) thermography predicts failure points in composites specimens with porosity defects introduced from nonideal manufacturing processes. Furthermore, these manufacturing defects are shown to compromise the fatigue life of the acrylic laminates by an order of magnitude.

effect of defects↗
DOE OSTI2021

Bayesian calibration of strength model parameters from Taylor impact data

Materials strength plays a key role in determining the mechanical response of engineered structures. As such, accurate strength models are crucial in simulations involving complex loading conditions, particularly when deformation in the plastic regime is deemed important. In this work, a Gaussian process based surrogate for a finite element simulation of a Taylor impact test is developed and used for Bayesian calibration of the Preston–Tonks–Wallace strength model. Here, the surrogate model is shown to closely approximate the salient features of the Taylor cylinder deformation and is validated against simulation output before being used in the strength model calibration routine. The results show that Taylor impact test data can be used in the calibration of constitutive equations through the use of a combination of data science techniques, namely Gaussian processes and Bayesian inference.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Innovations in underground hydrogen storage with multiphysics simulations, optimization, and monitoring: A review

Underground Hydrogen Storage (UHS) is a promising solution for large-scale energy storage and a critical component in advancing low-carbon energy system. Ensuring the safety and efficiency of UHS necessitates a comprehensive understanding of multiphysical interactions driven by cyclic pore fluid pressure fluctuations and coupled physicochemical processes. Here, this review examines the key geomechanical responses in UHS, including rock property variations under cyclic loading, fracture evolution and propagation, reservoir stress sensitivity, and fault stability. It also explores the impact of geochemical and microbial reactions on geomechanical characteristics. We provide an in-depth analysis of Thermal-Hydraulic-Mechanical-Chemical (THMC) coupled numerical simulations, highlighting their potential for future multi-scale modeling. Limitations of current machine learning (ML) approaches in addressing UHS challenges are highlighted, emphasizing the need for innovative ML-based methodologies. Operational strategies for hydrogen injection and production are reviewed, focusing on safety, efficiency, and economic viability. The necessity for multi-objective optimization (MOO) to balance storage efficiency, risk mitigation, and cost-effectiveness is also discussed. Current monitoring technologies are evaluated to ensure safe and efficient UHS operations. Finally, this review identifies critical knowledge gaps and underscores the importance of advancing geomechanical understanding under multiphysics-coupling. We highlight the need for ML-driven multiphysics theories, enhanced modeling techniques, and robust optimization strategies to improve UHS performance. This study serves as a comprehensive reference for future research and the large-scale implementation of UHS systems.

25 ENERGY STORAGE↗
DOE OSTI2021

Labile Fe(III) supersaturation controls nucleation and properties of product phases from Fe(II)-catalyzed ferrihydrite transformation

We report Fe(II)-catalyzed ferrihydrite (Fh) transformation to more crystalline iron (oxyhydr)oxide phases is a widely occurring geochemical process which has been extensively studied as a function of Fe(II)/Fh ratios at fixed Fh loadings. However, recent isolation of an intermediate Fe(III) species resulting from Fe(II)-Fh contact that facilitates transformation by dissolution/reprecipitation suggests that the kinetics and properties of product phases will instead depend mostly on its rate of accumulation to a critical concentration, consistent with principles in the classical nucleation theory (CNT). This suggests a dependence both on the loading of Fe(II) on the surface, which controls the rate of labile Fe(III) formation, as well as the available volume of solution, which also impacts how fast it can achieve its critical concentration to nucleate product phases. To specifically examine the latter effect, here we studied transformation of 15 mg Fh in 1 mM FeSO 4 solutions at pH 7.2 in batch suspensions of 30 mL, 150 mL, and 450 mL volumes. Time-dependent concentrations of aqueous Fe(II), surface-associated Fe(II), and resulting labile Fe(III) were monitored along with bulk solids characterization as a function of time. Transmission electron microscopy (TEM) was used to visualize the evolution of phases at identical locations on TEM grids. The collective results show that the rates of Fh loss and emergence of product lepidocrocite (Lp) and goethite (Gt) as well as their phase proportions, nucleation mode and morphological properties depend directly on the rate of accumulation of the labile Fe(III) precursor to its critical concentration, which in our experiments was controlled simply by varying the available volume of solution into which it enters. Statistical analyses of TEM image data suggest that while both heterogeneous and homogeneous nucleation occurred in all experiments, the former was increasingly favored at lower Fh/solution ratio due to its lower nucleation barrier being more favorable at attendant lower supersaturations of Fe(III).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Additively manufactured β-Ti5553 with laser powder bed fusion: Microstructures and mechanical properties of bulk and lattice parts

Ti5553 (Ti-5Al-5Mo-5V-3Cr wt%) is a titanium alloy widely used for its high strength-to-weight ratio and good formability at elevated temperatures. Unlike Ti-6Al-4V, Ti5553 does not undergo martensitic transformation, preventing cracking of brittle martensite upon rapid cooling. This makes it a strong candidate for additive manufacturing (AM), particularly laser powder bed fusion (L-PBF). L-PBF offers the unique opportunity to make fine lattice structures to reduce component weight. Despite the growing field of AM, there have been limited studies on L-PBF Ti5553 lattices and how their properties differ from the bulk. Here the present work addresses this knowledge gap by investigating microstructures and properties of L-PBF bulk and lattice parts and the effect of post L-PBF heat treatments. Electron microscopy and mechanical testing show that the high dislocation density formed during L-PBF increases bulk part’s yield strength by approximately 100 MPa compared to the conventional alloy. Digital image correlation during compression testing of octet truss lattices reveals a layer-by-layer failure mode. Compared to the bulk, the lattice contains copious ω nanoprecipitation, weaker <001> texture, smaller average grain sizes, and larger content of high-angle grain boundaries. These features elicit differences in Taylor factor distributions for the lattice depending on load direction, underlining challenges in predicting lattice mechanical response based on bulk properties. By examining the processing-structure-property relationships in the bulk and lattice, the present results delineate their microstructural and mechanical differences and establish a benchmark for the future design applications of L-PBF Ti5553.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Exploring the structural uniformity and integrity of protonic ceramic thin film electrolyte using wet powder spraying

Thin protonic ceramic electrolyte contributes to lower ohmic resistance and enhances electrochemical performance of protonic ceramic electrochemical cells. However, manufacturing of large-scale thin electrolyte remains a challenge. Wet powder spraying is an attractive technique to deposit <10 µm thin electrolyte when advanced atomizing techniques and optimized spraying process are integrated. Here ultrasonic atomization is integrated in the wet powder spray technique to reduce the thickness of electrolyte. Moreover, a parametric study is conducted to optimize the wet powder spray process to deposit uniform and crack-free electrolyte film. It is illustrated that tuning of solid loading rates and spray passes can affect the morphology of the as-sprayed electrolyte film, enabling the structural compactness of the sintered electrolyte layer. To maintain chemical stability of the electrolyte layer during sintering, effect of sintering temperature is further investigated to produce a physically thin, structurally dense, and chemically homogeneous electrolyte layer. The protonic ceramic electrochemical cells fabricated with optimized spraying and sintering parameters demonstrate excellent performance under both fuel cell and electrolysis modes. In addition, the cells exhibit remarkable structural integrity during redox and long-term stability tests.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Unraveling the Origin of Photocatalytic Deactivation in CeO 2 /Nb 2 O 5 Heterostructure Systems during Methanol Oxidation: Insight into the Role of Cerium Species

The study provides deep insight into the origin of photocatalytic deactivation of Nb 2 O 5 after modification with ceria. Of particular interest was to fully understand the role of ceria species in diminishing the photocatalytic performance of CeO 2 /Nb 2 O 5 heterostructures. For this purpose, ceria was loaded on niobia surfaces by wet impregnation. The as-prepared materials were characterized by powder X-ray diffraction, nitrogen physisorption, UV-visible spectroscopy, X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy, and photoluminescence measurements. Photocatalytic activity of parent metal oxides (i.e., Nb 2 O 5 and CeO 2 ) and as-prepared CeO 2 / Nb 2 O 5 heterostructures with different ceria loadings were tested in methanol photooxidation, a model gas-phase reaction. Deep insight into the photocatalytic process provided by operando-IR techniques combined with results of photoluminescence studies revealed that deactivation of CeO 2 /Nb 2 O 5 heterostructures resulted from increased recombination of photo-excited electrons and holes. The main factor contributing to more efficient recombination of the charge carriers in the heterostructures was the ultrafine size of the ceria species. The presence of such highly dispersed ceria species on the niobia surface provided a strong interface between these two semiconductors, enabling efficient charge transfer from Nb 2 O 5 to CeO 2 . However, the ceria species supported on niobia exhibited a high defect site concentration, which acted as highly active recombination centers for the photo-induced charge carriers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Role of tilt grain boundaries on the structural integrity of WSe 2 monolayers

Transition metal dichalcogenides (TMDCs) are potential materials for future optoelectronic devices. Grain boundaries (GBs) can significantly influence the optoelectronic properties of TMDC materials. Here, we have investigated the mechanical characteristics of tungsten diselenide (WSe 2 ) monolayers and failure process with symmetric tilt GBs using ReaxFF molecular dynamics simulations. In particular, the effects of topological defects, loading rates, and temperatures are investigated. We considered nine different grain boundary structures of monolayer WSe 2 , of which six are armchair (AC) tilt structures, and the remaining three are zigzag (ZZ) tilt structures. Our results indicate that both tensile strength and fracture strain of WSe 2 with symmetric tilt GBs decrease as the temperature increases. We revealed an interfacial phase transition for high-angle GBs reduces the elastic strain energy within the interface at finite temperatures. Furthermore, brittle cracking is the dominant failure mode in the WSe 2 monolayer with tilted GBs. WSe 2 GB structures showed more strain rate sensitivity at high temperatures than at low temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Anodic arc discharge: Why pulsed?

Pulsed anodic arc discharge is a novel synthesis method of nanomaterials by means of low-temperature atmospheric plasma. The technique consists in periodically supplying DC power to two vertically aligned electrodes in the form of short unipolar pulses with peak currents of a few hundred Amperes in helium atmosphere. The pulsed arc plasmas are sustained at frequencies of the order of 1 Hz with around 10% of duty cycle. It constitutes a versatile technique thanks to a series of advantages compared to continuous DC arc processes, in particular: flexibility in the experimental conditions, process stability and repeatability, better utilization of ablating anode material, lower production of macroparticles, and lower thermal loads. Such features are discussed in this article. A brief overview concerning the recent accomplishments of pulsed arc discharge on deposition of carbon nanostructures (graphene and carbon nanotubes) and few-layer flakes of molybdenum disulphide (MoS 2 ) is provided, as well as an outlook on future applications of this method for the discovery of new materials with tailored functional properties.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Exploring the parameter space of MagLIF implosions using similarity scaling. II. Current scaling

Magnetized liner inertial fusion (MagLIF) is a magneto-inertial-fusion (MIF) concept, which is presently being studied on the Z pulsed power facility. The MagLIF platform has achieved interesting plasma conditions at stagnation and produced significant fusion yields in the laboratory. Given the relative success of MagLIF, there is a strong interest to scale the platform to higher peak currents. However, scaling MagLIF is not entirely straightforward due to the large dimensionality of the experimental input parameter space and the numerous physical processes involved in MIF implosions. Here, in this work, we propose a novel method to scale MagLIF loads to higher currents. Our method is based on similarity (or similitude) scaling and attempts to preserve much of the physics regimes already known or being studied on today's Z pulsed-power driver. By avoiding significant deviations into unexplored and/or less well-understood regimes, the risk of unexpected outcomes on future scaled-up experiments is reduced. Using arguments based on similarity scaling, we derive the scaling rules for the experimental input parameters characterizing a MagLIF load (as functions of the characteristic current driving the implosion). We then test the estimated scaling laws for various metrics measuring performance against results of 2D radiation–magneto-hydrodynamic hydra simulations. Agreement is found between the scaling theory and the simulation results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Preshaping clear glass at low temperatures

Advances in available glass chemistries and glass processing methods have accompanied and enabled some of the biggest technology revolutions, from the development and mass production of light bulbs to low-loss fiber optics and durable smartphone touchscreens. An emerging generation of low-temperature processing technologies aims to continue this important trend and make a broader array of glass components mass producible. In the issue, Mader et al. (1) describe one such innovation in glass processing—the use of low-temperature injection molding to preshape silica particle–filled composites that can later be transformed into transparent fused silica glass objects. Traditionally, transparent glass objects are manufactured in high volume from molten or softened glass, which is floated, drawn, blown, cast, or blow-molded to a desired shape (see the figure, top). The glass composition and processing technique dictate the working temperature, which is usually quite high (near 1000°C) and often restricts the choice of compatible equipment or limits the choice of glass composition. Because geometry-specific capital investment is required for production, drastic or frequent component design changes or small batches may be cost prohibitive. Alternatively, transparent glass components can also be shaped at ambient temperature from solid glass by a series of subtractive processes, including cutting or multiple stages of grinding, followed by slower processing steps, such as polishing or etching. This approach is somewhat less amenable to mass production, and certain geometries containing tool-inaccessible regions cannot be fabricated in this way. Several emerging glass-shaping technologies aim to reduce the required manufacturing temperatures and still provide access to a broader range of glass compositions and component geometries (see the figure). These approaches use a three-step process. First, a desired shape is preformed at low temperature from a glass-forming, organic-inorganic composite. Next, the preform is dried, and organic materials used to bind particles are removed. Finally, the preform is heated (sintered) well below the glass-melting temperature to densify to transparent glass. Although the second and third steps do occur at increased temperatures, only standard, geometry-agnostic driers and furnaces are required. This strategy builds on the well-studied sol-gel approach to forming monolithic glass, where silica network–forming chemical solutions are poured into molds, slowly dried, and condensed into dense glass without melting (2). In a departure from the sol-gel process, these new technologies use solvents, cross-linkers, and polymers to formulate organic-inorganic composites tuned for compatibility with a particular shaping process, with formats ranging from photocurable liquids to shear-thickening pastes to solids. The composite inorganic loadings are also typically higher than those in the pure sol-gel approach, which drastically reduces shrinkage in comparison.

36 MATERIALS SCIENCE↗
DOE OSTI2020

DEPRECATED EVOLVE [SWR-20-79]

DEPRECATED This repository was archived by the owner on Jun 30, 2026. It is now read-only. EVOLVE is a combination of a dashboard developed in React, which enables user to visualize the net load evolution with emerging technologies such as PV, energy storage, and electric vehicles, and a Python backend processes data. A user can choose settings for solar, energy storage, and electric vehicles in the dashboard. Modules that are developed to model the impact of these DERs can also be used independently without being integrated into the dashboard. We used a RESTful API to expose these modules to the React front-end.

Duwadi, Kapil↗
DOE OSTI2021

Spent Crystalline Silicotitanate Storage Study—Post AP-105DF Processing

A Tank-Side Cesium Removal (TSCR) system is under development by Washington River Protection Solutions to support initial production of immobilized low-activity waste (LAW) by feeding Hanford tank supernate from tank farms to the Hanford Waste Treatment and Immobilization Plant (WTP) LAW Facility. Tank waste supernate is filtered to remove suspended solids and then Cs is removed by processing it through crystalline silicotitanate (CST) ion exchange media manufactured by Honeywell UOP, LLC. The Cs-loaded CST columns will be stored indefinitely, with a goal of eventual CST removal and treatment. Thus, the spent CST needs to be recoverable after undetermined storage time. Previous testing with AP-105 simulant showed that rinsing the CST bed with 3 bed volumes (1.4 apparatus volumes [AVs]) of 0.1 M NaOH resulted in a dried bed that maintained flow characteristics indicative of ease of recovery. This study explored the intermediate conditions (between feed dried in place and the 1.4 AVs of 0.1 M NaOH rinse) to evaluate CST bed properties.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Additive Manufacturing of Isotropic NdFeB PPS Bonded Permanent Magnets

Extrusion based additive manufacturing of polymer composite magnets can increase the solid loading volume fraction with greater mechanical force through the printing nozzle as compared to traditional injection molding process. About 63 vol% of isotropic NdFeB magnet powders were compounded with 37 vol% of polyphenylene sulfide and bonded permanent magnets were fabricated while using Big Area Additive Manufacturing without any degradation in magnetic properties. The polyphenylene sulfide bonded magnets have a tensile stress of 20 MPa, almost double than that of nylon bonded permanent magnets. Additively manufactured and surface-protective-resin coated bonded magnets meet the industrial stability criterion of up to 175 °C with a flux-loss of 2.35% over 1000 h. They also exhibit better corrosion resistance behavior when exposed to acidic (pH = 1.35) solution for 24 h and also annealed at 80 °C over 100 h (at 95% relative humidity) over without coated magnets. Thus, polyphenylene sulfide bonded, additively manufactured, protective resin coated bonded permanent magnets provide better thermal, mechanical, and magnetic properties.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Titanium reinforced boron polyimide composite

Program involves development of process technique for boron-polyimide prepeg, lay-up and curing procedures for prepegs when processed under vacuum bag pressure, and development and evaluation of titanium hard points for smooth transition of loads from titanium attach points into boron reinforced body of structure.

Clark, G. A.↗
NASA NTRS1972

Analyses of requirements for computer control and data processing experiment subsystems. Volume 2: ATM experiment S-056 image data processing system software development

The IDAPS (Image Data Processing System) is a user-oriented, computer-based, language and control system, which provides a framework or standard for implementing image data processing applications, simplifies set-up of image processing runs so that the system may be used without a working knowledge of computer programming or operation, streamlines operation of the image processing facility, and allows multiple applications to be run in sequence without operator interaction. The control system loads the operators, interprets the input, constructs the necessary parameters for each application, and cells the application. The overlay feature of the IBSYS loader (IBLDR) provides the means of running multiple operators which would otherwise overflow core storage.

Source record↗
NASA NTRS1976

Application of NASTRAN to large deflection supersonic flutter of panels

Flat panel flutter at high supersonic Mach number is analyzed using NASTRAN Level 16.0 by means of modifications to the code. Two-dimensional plate theory and quasi-steady aerodynamic theory are employed. The finite element formulation and solution procedure are presented. Modifications to the NASTRAN code are discussed. Convergence characteristics of the iteration processes are also briefly discussed. Effects of aerodynamic damping, boundary support condition and applied in-plane loading are included. Comparison of nonlinear vibration and linear flutter results with analytical solutions demonstrate that excellent accuracy is obtained with NASTRAN.

Mei, C.↗