Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Analytical study of the performance of a gust alleviation system for a STOL airplane

An analytical study has shown that a gust alleviation system for a STOL airplane in a cruise condition could reduce the root mean square of the normal acceleration of the airplane flying in random turbulence by as much as 50 percent. This alleviation is obtained by driving the flaps in response to normal acceleration and by moving the elevator in proportion to the commanded flap deflection angle and to a pitch-rate signal.

Oehman, W. I.↗
NASA NTRS1973

Engine-over-the-wing noise research

Acoustic measurements for large model eingine-over-the-wing (EOW) research configurations having both conventional and powered lift applications were taken for flap positions typical of takeoff and approach and at locations simulating flyover and sideline. The results indicate that the noise is shielded by the wing and redirected above it, making the EOW concept a prime contender for quiet aircraft. The large-scale noise data are in agreement with earlier small-model results. Below the wing, the EOW configuration is about 10 PNdb quieter than the engine-under-the-wing externally-blown-flap for powered lift, and up to 10 db quieter than the nozzle alone at high frequencies for conventional lift applications.

Reshotko, M.↗
NASA NTRS1973

The Buffalo/Spey jet-STOL research aircraft

The program to design and build a Buffalo/Spey Augmentor-Wing research aircraft is presented. The development of an internally blown flap system for the generation of powered lift is discussed. Modification, development, and testing of the Rolls-Royce Spey engine are reported. The ground tests and first flights of the aircraft are described and the application of the internally blown flap concept for short takeoff military transport aircraft is proposed.

Whittley, D. C.↗
NASA NTRS1973

Laser Doppler velocimeter investigation of trailing vortices behind a semi-span swept wing in a landing configuration

Measured axial and tangential velocity profiles in the near wake vortices of a semi-span model of the Convair 990 wing in the NASA-Ames 7- by 10-foot wind tunnel are presented. A scanning laser Doppler velocimeter was used to obtain data at two different downstream stations (0.49 and 1.25 wing spans) at various angles of attack and configurations from wing alone to wing plus nacelles, anti-shock bodies, and flaps deflected 27 deg (landing configuration). It is shown that the velocity distributions within the wake are quite sensitive to span loading. Specifically, it is illustrated that an aircraft flying at given lift coefficient (C SUB L), can substantially reduce its trailing vortex upset potential by deploying its flaps and altering its flight attitude to maintain the same C SUB L. This might be taken into consideration along with performance and noise considerations in the selection of aircraft approach lift over drag.

Ciffone, D. L.↗
NASA NTRS1973

Exposure interlock for oscilloscope cameras

An exposure interlock has been developed for oscilloscope cameras which cuts off ambient light from the oscilloscope screen before the shutter of the camera is tripped. A flap is provided which may be selectively positioned to an open position which enables viewing of the oscilloscope screen and a closed position which cuts off the oscilloscope screen from view and simultaneously cuts off ambient light from the oscilloscope screen. A mechanical interlock is provided between the flap to be activated to its closed position before the camera shutter is tripped, thereby preventing overexposure of the film.

Spitzer, C. R.↗
NASA NTRS1972

Quiet STOL propulsion session introductory remarks

Research activities, preliminary design activities, and system optimization studies in support of the development of advanced, quiet, STOL propulsion systems are discussed. Noise alleviation by means of controlling the source and by means of acoustical treatment receive considerable emphasis. A STOL airplane designed for a given payload has essentially double the installed thrust of a comparable CTOL airplane. Unless compensated for during the design process, this alone will tend to increase the source noise by 3 db. The propulsive lift introduces flap impingement noise or duct and flap scrubbing noise, noise sources not present in CTOL airplanes to any significant degree. These additional noise sources are illustrated. Depending on the specific configuration, this will tend to increase the noise by several db or more. Although the propulsive lift characteristics of STOL airplanes will tend to increase source noise significantly, the proximity of STOL airfields to populated areas leads to STOL noise objectives considerably lower than those currently applicable to CTOL airplanes.

Schroeder, R. W.↗
NASA NTRS1972

Acoustic results obtained with upper-surface-blowing lift-augmentation systems.

The noise caused by the interaction of the jet exhaust and a wing was measured under static conditions for several versions of a small-scale STOL engine-over-the-wing configuration. Three basic nozzles were used in the tests; a circular nozzle, a 5:1 aspect ratio slot nozzle, and a 10:1 aspect ratio slot nozzle. Various flow attachment devices were included in the study. The wing included a flap that could be positioned for nominal takeoff or approach flap settings. Far field noise data are presented for the flyover mode. The data are discussed in terms of sound power and sound pressure spectra.

Von Glahn, U.↗
NASA NTRS1973

Analysis of stall flutter of a helicopter rotor blade.

A study of rotor blade aeroelastic stability was carried out, using an analytic model of a two-dimensional airfoil undergoing dynamic stall and on elastomechanical representation including flapping, flapwise bending and torsional degrees of freedom. Results for a hovering rotor demonstrated that the models used are capable of reproducing both classical and stall flutter. The minimum rotor speed for the occurrence of stall flutter in hover was found to be determined from coupling between torsion and flapping. Instabilities analogous to both classical and stall flutter were found to occur in forward flight. However, the large stall-related torsional oscillations which commonly limit aircraft forward speed appear to be the response to rapid changes in aerodynamic moment which accompany stall and unstall, rather than the result of an aeroelastic instability.

Crimi, P.↗
NASA NTRS1973

Engine-over-the-wing noise research.

Acoustic measurements for large model engine-over-the-wing (EOW) research configurations having both conventional and powered lift applications were taken for flap positions typical of takeoff and approach and at locations simulating flyover and sideline. The results indicate that the noise is shielded by the wing and redirected above it, making the EOW concept a prime contender for quiet aircraft. The large-scale noise data are in agreement with earlier small-model results. Below the wing, the EOW configuration is about 10 PNdB quieter than the engine-under-the-wing externally-blown-flap for powered lift, and up to 10 dB quieter than the nozzle alone at high frequencies for conventional lift applications.

Reshotko, M.↗
NASA NTRS1972

On the role of the radiation directivity in noise reduction for STOL aircraft.

The radiation characteristics of distributed randomly fluctuating acoustic sources when shielded by finite surfaces are discussed briefly. A number of model tests using loudspeakers as artificial noise sources with a given broadband power density spectrum are used to demonstrate the effectiveness of reducing the radiated noise intensity in certain directions due to shielding. In the lateral direction of the source array noise reductions of 12 dB are observed with relatively small shields. The same shields reduce the backward radiation by approximately 20 dB. With the results obtained in these acoustic model tests the potentials of jet noise reduction of jet flap propulsion systems applicable in future STOL aircraft are discussed. The jet flap configuration as a complex aerodynamic noise source is described briefly.

Gruschka, H. D.↗
NASA NTRS1974

Calculation of aerodynamic characteristics of STOL aircraft

Method predicts lift and pitching moment characteristics of STOL aircraft with externally-blown, jet-augmented wing-flap combinations using potential-flow approach which involves combination of two flow models. Method can accommodate multiple engines per wing panel and part-span flaps.

Dillenius, M. F. E.↗
NASA NTRS1973

Acoustic characteristics of a large-scale augmentor wing model at forward speed

The augmentor wing concept is being studied as one means of attaining short takeoff and landing (STOL) performance in turbofan powered aircraft. Because of the stringent noise requirements for STOL operation, the acoustics of the augmentor wing are undergoing extensive research. The results of a wind tunnel investigation of a large-scale swept augmentor model at forward speed are presented. The augmentor was not acoustically treated, although the compressor supplying the high pressure primary air was treated to allow the measurement of only the augmentor noise. Installing the augmentor flap and shroud on the slot primary nozzle caused the acoustic dependence on jet velocity to change from eighth power to sixth power. Deflecting the augmentor at constant power increased the perceived noise level in the forward quadrant. The effect of airspeed was small. A small aft shift in perceived noise directivity was experienced with no significant change in sound power. Sealing the lower augmentor slot at a flap deflection of 70 deg reduced the perceived noise level in the aft quadrant. The seal prevented noise from propagating through the slot.

Falarski, M. D.↗
NASA NTRS1973

Stability and control characteristics of a Langley concept space shuttle orbiter (LO-100) at low subsonic speeds

An experimental aerodynamic investigation was conducted on a 0.01 scale model of a Langley concept space shuttle orbiter (LO-100) in the Langley Low Turbulence Pressure Tunnel at a Mach number of 0.25 and at a Reynolds number of 5.4 million per foot. The angle of attack was varied from about -2 deg to 24 deg at 0 deg and 5 deg sideslip. The configuration was tested at elevon settings of 0 deg, -5 deg, -10 deg, and -15 deg for a body base flap setting of 0 deg and at 0 deg, -10 deg, and -15 deg for a body base flap setting of -18 deg. The effect of rudder flare angle was obtained using 0 deg, 20 deg, and 40 deg, flare settings.

Spencer, B., Jr.↗
NASA NTRS1973

Analysis of stall flutter of a helicopter radar blade

A study of rotor blade aeroelastic stability was carried out, using an analytic model of a two-dimensional airfoil undergoing dynamic stall and an elastomechanical representation including flapping, flapwise bending and torsional degrees of freedom. Results for a hovering rotor demonstrated that the models used are capable of reproducing both classical and stall flutter. The minimum rotor speed for the occurrence of stall flutter in hover, was found to be determined from coupling between torsion and flapping. Instabilities analogous to both classical and stall flutter were found to occur in forward flight. However, the large stall-related torsional oscillations which commonly limit aircraft forward speed appear to be the response to rapid changes in aerodynamic moment which accompany stall and unstall, rather than the result of an aeroelastic instability. The severity of stall-related instabilities and response was found to depend to some extent on linear stability. Increasing linear stability lessens the susceptibility to stall flutter and reduced the magnitude of the torsional response to stall and unstall.

Crimi, P.↗
NASA NTRS1968

Concepts for a theoretical and experimental study of lifting rotor random loads and vibrations, Phase 2

A comparison with NASA conducted simulator studies has shown that the approximate digital method for computing rotor blade flapping responses to random inputs, tentatively suggested in Phase I Report, gives with increasing rotor advance ratio the wrong trend. Consequently, three alternative methods of solution have been considered and are described: (1) an approximate method based on the functional relation between input and output double frequency spectra, (2) a numerical method based on the system responses to deterministic inputs and (3) a perturbation approach. Among these the perturbation method requires the least amount of computation and has been developed in two forms - the first form to obtain the response correlation function and the second for the time averaged spectra of flapping oscillations.

Hohenemser, K. H.↗
NASA NTRS1973

A study to determine the applicability of noise abatement approach procedures to McDonnell Douglas Aircraft

Analyses of McDonnell Douglas DC-8, DC-9, and DC-10 jet transports were conducted to investigate the applicability of two segment approach noise abatement procedures to these airplanes. All models had the required glide slope capability at the certified landing flap settings. The DC-8 models would probably be limited to an upper segment glide slope of 5.5 degrees and would probably not be suitable for the two segment procedure in icing conditions. The DC-8 would not be compatible with this procedure at a reduced landing flap setting. The feasibility of installing a two segment approach system in the Douglas-built fleet of commercial jet transports from a hardware viewpoint is discussed. The candidate system consists of a two segment computer plus the necessary peripheral equipment interfaced with the existing autopilot and associated avionics. The required modifications and additions to existing equipment are described and the attendant costs estimated. Potential problems which may be encountered are also discussed.

Painter, J. A.↗
NASA NTRS1973

Experimental hingeless rotor characteristics at low advance ratio with thrust

An experimental investigation to determine the dynamic characteristics of a hingeless rotor operating at moderate to high lift was conducted on a small scale, 7.5-foot diameter, four-bladed hingeless rotor model in a 7 x 10-foot wind tunnel. The primary objective of this research program was the empirical determination of the rotor steady-state and frequency responses to swashplate and body excitations. Collective pitch was set from 0 to 20 degrees, with the setting at a particular advance ratio limited by the cyclic pitch available for hub moment trim. Advance ratio varied from 0.00 to 0.36 for blades with nondimensional first-flap frequencies at 1.15, 1.28 and 1.33 times the rotor rotation frequency. Several conditions were run with the rotor operating in the transition regime. Rotor response at high lift is shown to be generally nonlinear in this region. As a secondary objective an experimental investigation of the rotor response to 4/revolution swashplate excitations at advance ratios of 0.2 to 0.85 and at a nondimensional, first-flap modal frequency of 1.34 was also conducted, using the 7 x 10-foot wind tunnel. It is shown that 4/revolution swashplate inputs are a method for substantially reducing rotor-induced, shafttransmitted vibratory forces.

London, R. J.↗
NASA NTRS1974

Noise measurements at Stockton airport obtained during engineering evaluation of two-segment approaches in a DC-8-61 aircraft

A series of noise measurements were made during engineering evaluation tests of the two segment approach using a DC-8-61. The two approaches evaluated were: (1) ILS, 2.9 deg glide slope using 50 deg flaps; and (2) two segment 5.5 deg/2.9 deg glide slope, using 50 deg flaps and lower segment intercept altitude of 575 feet. Measurements were made at twelve sites underneath and to the side of the flight path.

Glass, R. E.↗