Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “consistent filtering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Imaging experiment - The Viking Mars Orbiter.

The general objectives of the imaging experiment on the Viking Orbiter are to aid the selection of Viking Lander sites, to map and monitor the chosen sites during lander operations, to aid in the selection of future landing sites, and to extend our knowledge of the planet. The imaging system consists of two identical vidicon cameras each attached to a 1026-mm T/8 telescope giving approximately 1-deg square field of view. From an altitude of 1500 km, the picture elements will be approximately 24 m apart. The vidicon is coupled with an image intensifier which provides increased sensitivity and permits electronic shuttering and image motion compensation. The camera differs from those previously flown to Mars by providing contiguous coverage at high resolution on a single orbital pass, by having sufficient sensitivity to use narrow band color filters at maximum resolution, and by having response in the ultraviolet.

Carr, M. H.↗

Fault-tolerant system considerations for a redundant strapdown inertial measurement unit

The development and evaluation of a fault-tolerant system for the Redundant Strapdown Inertial Measurement Unit (RSDIMU) being developed and evaluated by the NASA Langley Research Center was continued. The RSDIMU consists of four two-degree-of-freedom gyros and accelerometers mounted on the faces of a semi-octahedron which can be separated into two halves for damage protection. Compensated and uncompensated fault-tolerant system failure decision algorithms were compared. An algorithm to compensate for sensor noise effects in the fault-tolerant system thresholds was evaluated via simulation. The effects of sensor location and magnitude of the vehicle structural modes on system performance were assessed. A threshold generation algorithm, which incorporates noise compensation and filtered parity equation residuals for structural mode compensation, was evaluated. The effects of the fault-tolerant system on navigational accuracy were also considered. A sensor error parametric study was performed in an attempt to improve the soft failure detection capability without obtaining false alarms. Also examined was an FDI system strategy based on the pairwise comparison of sensor measurements. This strategy has the specific advantage of, in many instances, successfully detecting and isolating up to two simultaneously occurring failures.

Motyka, P.↗

Peak-Seeking Optimization of Trim for Reduced Fuel Consumption: Flight-Test Results

A peak-seeking control algorithm for real-time trim optimization for reduced fuel consumption has been developed by researchers at the National Aeronautics and Space Administration (NASA) Dryden Flight Research Center to address the goals of the NASA Environmentally Responsible Aviation project to reduce fuel burn and emissions. The peak-seeking control algorithm is based on a steepest-descent algorithm using a time-varying Kalman filter to estimate the gradient of a performance function of fuel flow versus control surface positions. In real-time operation, deflections of symmetric ailerons, trailing-edge flaps, and leading-edge flaps of an F/A-18 airplane (McDonnell Douglas, now The Boeing Company, Chicago, Illinois) are used for optimization of fuel flow. Results from six research flights are presented herein. The optimization algorithm found a trim configuration that required approximately 3 percent less fuel flow than the baseline trim at the same flight condition. The algorithm consistently rediscovered the solution from several initial conditions. These results show that the algorithm has good performance in a relevant environment.

flight optimization↗

Peak-Seeking Optimization of Trim for Reduced Fuel Consumption: Flight-test Results

A peak-seeking control algorithm for real-time trim optimization for reduced fuel consumption has been developed by researchers at the National Aeronautics and Space Administration (NASA) Dryden Flight Research Center to address the goals of the NASA Environmentally Responsible Aviation project to reduce fuel burn and emissions. The peak-seeking control algorithm is based on a steepest-descent algorithm using a time-varying Kalman filter to estimate the gradient of a performance function of fuel flow versus control surface positions. In real-time operation, deflections of symmetric ailerons, trailing-edge flaps, and leading-edge flaps of an F/A-18 airplane (McDonnell Douglas, now The Boeing Company, Chicago, Illinois) are used for optimization of fuel flow. Results from six research flights are presented herein. The optimization algorithm found a trim configuration that required approximately 3 percent less fuel flow than the baseline trim at the same flight condition. The algorithm consistently rediscovered the solution from several initial conditions. These results show that the algorithm has good performance in a relevant environment.

flight optimization↗

Feasibility study consisting of a review of contour generation methods from stereograms

A review of techniques for obtaining contour information from stereo pairs is given. Photogrammetric principles including a description of stereoscopic vision are presented. The use of conventional contour generation methods, such as the photogrammetric plotting technique, electronic correlator, and digital correlator are described. Coherent optical techniques for contour generation are discussed and compared to the electronic correlator. The optical techniques are divided into two categories: (1) image plane operation and (2) frequency plane operation. The description of image plane correlators are further divided into three categories: (1) image to image correlator, (2) interferometric correlator, and (3) positive negative transparencies. The frequency plane correlators are divided into two categories: (1) correlation of Fourier transforms, and (2) filtering techniques.

Kim, C. J.↗

Fish scale deformation analysis using scanning electron microscope: New potential biomarker in aquatic environmental monitoring of aluminum and iron contamination

Fish scale has the potential to be a rapid biomarker due to its structure and high possibility to come into contact with any pollutant in the aquatic environment. The scale structure consists of osteoblastic cells and other bone materials such as collagen where it is possible to form a molecular complex with heavy metals such as aluminum and iron. Hence, aluminum and iron in water could possibly destroy the scale material and marked as a scale deformation that quantitatively could be analyzed by comparing it to the normal scale structure. Water sampling and fish cage experiment were performed between June and July 2011 in Porong river which represented the water body that has high aluminum and iron contamination. The filtered water samples were preserved and extracted using the acid-mixture procedure prior to measurement of the aluminum and iron concentrations using Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), while samples for total suspended solid (TSS) analysis were kept at 4 °C in cool-boxes. The scales were cleaned with sterile water, then dehydrated in 30, 50, 70, and 90% ethanol and dried on filter papers. They were then mounted on an aluminum stub and coated with gold in a sputter coater prior to Scanning Electron Microscope (SEM) observation. According to the SEM analysis, it was found that there were several deformations on the scale samples taken from sites that have high concentrations of aluminum and iron i.e. the increasing number of pits, deformation and decreasing number of spherules and ridges while the control scale exhibited the normal features. However, the site with higher TSS and pH indicated lower aluminum effect. A moderate correlation was found between the number of pits with aluminum (r=0.43) and iron (r=0.41) concentrations. Fish scale deformation using SEM analysis can potentially be a rapid biomarker in aquatic monitoring of aluminum and iron contamination. However, the measurement must be accompanied by pH and TSS observations.

36 MATERIALS SCIENCE↗

THE LONG-TERM DECAY IN PRODUCTION RATES FOLLOWING THE EXTREME OUTBURST OF COMET 17P/HOLMES

Numerous sets of narrowband filter photometry were obtained of Comet 17P/Holmes from Lowell Observatory during the interval of 2007 November 1 to 2008 March 5. Observations began 8 days following its extreme outburst, at which time the derived water production rate, based on OH measurements, was 5 x 10{sup 29} molecule s{sup -1} and the derived proxy of dust production, A({theta})f{rho}, was about 5 x 10{sup 5} cm. Relative production rates for the other gas species, CN, C{sub 2}, C{sub 3}, and NH, are consistent with 'typical' composition (based on our update to the classifications by A'Hearn et al.). An exponential decay in the logarithm of measured production rates as a function of time was observed for all species, with each species dropping by factors of about 200-500 after 125 days. All gas species exhibited clear trends with aperture size, and these trends are consistent with larger apertures having a greater proportion of older material that was released when production rates were higher. Much larger aperture trends were measured for the dust, most likely because the dust grains have smaller outflow velocities and longer lifetimes than the gas species; therefore, a greater proportion of older, i.e., higher production dust is contained within a given aperture. By extrapolating to a sufficiently small aperture size, we derive near-instantaneous water and dust production rates throughout the interval of observation, and also estimate values immediately following the outburst. The finite lifetime of the gas species requires that much higher ice vaporization rates were taking place throughout the observation interval than occurred prior to the outburst, likely due to the continued release of icy grains from the nucleus. The relatively small aperture trends for the gas species also imply that the bulk of fresh, excess volatiles are confined to the nucleus and near-nucleus regime, rather than being associated with the outburst ejecta cloud. A minimum of about 0.1% of the total nucleus volume was vaporized water ice, while a dust volume corresponding to at least 1%-2% was likely to have been released from the nucleus.

79 ASTRONOMY AND ASTROPHYSICS↗

THE PHOTOMETRIC PROPERTIES OF A VAST STELLAR SUBSTRUCTURE IN THE OUTSKIRTS OF M33

We have surveyed approximately 40 deg{sup 2} surrounding M33 with Canada-France-Hawaii Telescope MegaCam/MegaPrime in the g and i filters out to a maximum projected radius from this galaxy of 50 kpc, as part of the Pan-Andromeda Archaeological Survey (PAndAS). Our observations are deep enough to resolve the top {approx}4 mag of the red giant branch population in this galaxy. We have previously shown that the disk of M33 is surrounded by a large, irregular, low surface brightness substructure. Here, we quantify the stellar populations and structure of this feature using the PAndAS data. We show that the stellar populations of this feature are consistent with an old population with ([Fe/H]) {approx} -1.6 dex and an interquartile range in metallicity of {approx}0.5 dex. We construct a surface brightness map of M33 that traces this feature to {mu}{sub V} {approx_equal} 33 mag arcsec{sup -2}. At these low surface brightness levels, the structure extends to projected radii of {approx}40 kpc from the center of M33 in both the northwest and southeast quadrants of the galaxy. Overall, the structure has an 'S-shaped' appearance that broadly aligns with the orientation of the H I disk warp. We calculate a lower limit to the integrated luminosity of the structure of -12.7 {+-} 0.5 mag, comparable to a bright dwarf galaxy such as Fornax or Andromeda II and slightly less than 1% of the total luminosity of M33. Further, we show that there is tentative evidence for a distortion in the distribution of young stars near the edge of the H I disk that occurs at similar azimuth to the warp in H I. The data also hint at a low-level, extended stellar component at larger radius that may be an M33 halo component. We revisit studies of M33 and its stellar populations in light of these new results and discuss possible formation scenarios for the vast stellar structure. Our favored model is that of the tidal disruption of M33 in its orbit around M31.

79 ASTRONOMY AND ASTROPHYSICS↗

Exploring the contamination of the DES-Y1 cluster sample with SPT-SZ selected clusters

ABSTRACT We perform a cross validation of the cluster catalogue selected by the red-sequence Matched-filter Probabilistic Percolation algorithm (redMaPPer) in Dark Energy Survey year 1 (DES-Y1) data by matching it with the Sunyaev–Zel’dovich effect (SZE) selected cluster catalogue from the South Pole Telescope SPT-SZ survey. Of the 1005 redMaPPer selected clusters with measured richness $\hat{\lambda }\gt 40$ in the joint footprint, 207 are confirmed by SPT-SZ. Using the mass information from the SZE signal, we calibrate the richness–mass relation using a Bayesian cluster population model. We find a mass trend λ ∝ MB consistent with a linear relation (B ∼ 1), no significant redshift evolution and an intrinsic scatter in richness of σλ = 0.22 ± 0.06. By considering two error models, we explore the impact of projection effects on the richness–mass modelling, confirming that such effects are not detectable at the current level of systematic uncertainties. At low richness SPT-SZ confirms fewer redMaPPer clusters than expected. We interpret this richness dependent deficit in confirmed systems as due to the increased presence at low richness of low-mass objects not correctly accounted for by our richness-mass scatter model, which we call contaminants. At a richness $\hat{\lambda }=40$, this population makes up ${\gt}12{{\ \rm per\ cent}}$ (97.5 percentile) of the total population. Extrapolating this to a measured richness $\hat{\lambda }=20$ yields ${\gt}22{{\ \rm per\ cent}}$ (97.5 percentile). With these contamination fractions, the predicted redMaPPer number counts in different plausible cosmologies are compatible with the measured abundance. The presence of such a population is also a plausible explanation for the different mass trends (B ∼ 0.75) obtained from mass calibration using purely optically selected clusters. The mean mass from stacked weak lensing (WL) measurements suggests that these low-mass contaminants are galaxy groups with masses ∼3–5 × 1013 M⊙ which are beyond the sensitivity of current SZE and X-ray surveys but a natural target for SPT-3G and eROSITA.

79 ASTRONOMY AND ASTROPHYSICS↗

Optical–SZE scaling relations for DES optically selected clusters within the SPT-SZ Survey

We study the Sunyaev-Zel'dovich effect (SZE) signature in South Pole Telescope (SPT) data for an ensemble of 719 optically identified galaxy clusters selected from 124.6 deg$^2$ of the Dark Energy Survey (DES) science verification data, detecting a stacked SZE signal down to richness $\lambda\sim20$. The SZE signature is measured using matched-filtered maps of the 2500 deg$^2$ SPT-SZ survey at the positions of the DES clusters, and the degeneracy between SZE observable and matched-filter size is broken by adopting as priors SZE and optical mass-observable relations that are either calibrated using SPT selected clusters or through the Arnaud et al. (2010, A10) X-ray analysis. We measure the SPT signal to noise $\zeta$-$\lambda$, relation and two integrated Compton-$y$ $Y_\textrm{500}$-$\lambda$ relations for the DES-selected clusters and compare these to model expectations accounting for the SZE-optical center offset distribution. For clusters with $\lambda > 80$, the two SPT calibrated scaling relations are consistent with the measurements, while for the A10-calibrated relation the measured SZE signal is smaller by a factor of $0.61 \pm 0.12$ compared to the prediction. For clusters at $20 < \lambda < 80$, the measured SZE signal is smaller by a factor of $\sim$0.20-0.80 (between 2.3 and 10~$\sigma$ significance) compared to the prediction, with the SPT calibrated scaling relations and larger $\lambda$ clusters showing generally better agreement. We quantify the required corrections to achieve consistency, showing that there is a richness dependent bias that can be explained by some combination of contamination of the observables and biases in the estimated masses. We discuss possible physical effects, as contamination from line-of-sight projections or from point sources, larger offsets in the SZE-optical centering or larger scatter in the $\lambda$-mass relation at lower richnesses.

79 ASTRONOMY AND ASTROPHYSICS↗

Compact and multi-view solid state neutral particle analyzer arrays on National Spherical Torus Experiment-Upgrade

A compact and multi-view Solid State Neutral Particle Analyzer (SSNPA) diagnostic based on silicon photodiode arrays has been successfully tested on the National Spherical Torus Experiment-Upgrade (NSTX-U). The SSNPA diagnostic provides spatially, temporally, and pitch-angle resolved measurements of fast-ion distribution by detecting fast neutral flux resulting from charge exchange (CX) reactions. The system consists of three 16-channel subsystems: t-SSNPA viewing the plasma mid-radius and neutral beam (NB) line #2 tangentially, r-SSNPA viewing the plasma core and NB line #1 radially and p-SSNPA with no intersection with any NB lines. Due to the setup geometry, the active CX signals of t-SSNPA and r-SSNPA are mainly sensitive to passing and trapped particles respectively. In addition, both t-SSNPA and r-SSNPA utilize three vertically stacked arrays with different filter thickness to obtain coarse energy information. The experimental data show that all channels are operational. The signal to noise ratio is typically larger than 10 and the main noise is x-ray induced signal. The active and passive CX signals are clearly observed on t-SSNPA and r-SSNPA during NB modulation. The SSNPA data also indicate significant losses of passing particles during sawteeth, while trapped particles are weakly affected. Fluctuations up to 120 kHz, have been observed on SSNPA, and they are strongly correlated with magnetohydrodynamics (MHD) instabilities.

Charge exchange neutral particle fast ion distribu↗

Volcanic impact on stratospheric aerosol chemistry

Samples collected by the National Center for Atmospheric Research (NCAR) using the multiple-filter sampler on the U-2 were analyzed. The sampler is capable of exposing a number of 110 mm filters in sequence to ram air flow. Two types of filters, IPC cellulose and polystrene, were used, both of which have high blank levels for the trace elements determined. The levels of most trace elements in the stratosphere are so low under normal circumstances that none can be seen. Results from the eruption of Mt. St. Helens, a mystery cloud (probably volcanic in origin) in 1982, and the El Chichonal eruption in 1983 are discussed. To improve the collection of particles for chemical analysis, a new sampling system was developed for use on the U-2. The sampler consisted of an electrostatic collection of particles between 1 and 0.001 micron diameter dierectly onto electron microscopic grids, followed by a thermal precipitation for the smaller particles. The system was built and tested in the laboratory, but never flown on the U-2.

Zoller, W. H.↗

Compositional structure of the asteroid belt

A variety of observations, mainly albedos derived from 10 and 20 micron radiometry and eight-filter broadband spectrophotometry, were used to show that the asteroid belt is highly structured in composition. The bias-corrected distribution from 1.8 to 5.2 A.U. of the previously defined compositional types C,S,E,R, and M, plus type D and the newly described types F and P, are reported on. In terms of the relative abundances of the types discussed, the asteroid belt appears to be composed of at least six major compositionally distinct regions. The inferred composition of the asteroids in each semimajor axis region is consistent with the theory that the asteroids accreted from the solar nebula at or near their present location.

Gradie, J.↗

Equalization and detection for digital communication over nonlinear bandlimited satellite communication channels

This dissertation evaluates receiver-based methods for mitigating the effects due to nonlinear bandlimited signal distortion present in high data rate satellite channels. The effects of the nonlinear bandlimited distortion is illustrated for digitally modulated signals. A lucid development of the low-pass Volterra discrete time model for a nonlinear communication channel is presented. In addition, finite-state machine models are explicitly developed for a nonlinear bandlimited satellite channel. A nonlinear fixed equalizer based on Volterra series has previously been studied for compensation of noiseless signal distortion due to a nonlinear satellite channel. This dissertation studies adaptive Volterra equalizers on a downlink-limited nonlinear bandlimited satellite channel. We employ as figure of merits performance in the mean-square error and probability of error senses. In addition, a receiver consisting of a fractionally-spaced equalizer (FSE) followed by a Volterra equalizer (FSE-Volterra) is found to give improvement beyond that gained by the Volterra equalizer. Significant probability of error performance improvement is found for multilevel modulation schemes. Also, it is found that probability of error improvement is more significant for modulation schemes, constant amplitude and multilevel, which require higher signal to noise ratios (i.e., higher modulation orders) for reliable operation. The maximum likelihood sequence detection (MLSD) receiver for a nonlinear satellite channel, a bank of matched filters followed by a Viterbi detector, serves as a probability of error lower bound for the Volterra and FSE-Volterra equalizers. However, this receiver has not been evaluated for a specific satellite channel. In this work, an MLSD receiver is evaluated for a specific downlink-limited satellite channel. Because of the bank of matched filters, the MLSD receiver may be high in complexity. Consequently, the probability of error performance of a more practical suboptimal MLSD receiver, requiring only a single receive filter, is evaluated.

Gutierrez, Alberto, Jr.↗

CFD Based Design of a Filming Injector for N+3 Combustors

An effort was undertaken to perform CFD analysis of fluid flow in Lean-Direct Injection (LDI) combustors with axial swirl-venturi elements for next-generation LDI-3 combustor design. The National Combustion Code (NCC) was used to perform non-reacting and two-phase reacting flow computations for a newly-designed pre-filming type fuel injector LDI-3 injector, in a single-injector and a five-injector array configuration. All computations were performed with a consistent approach of mesh-optimization, spray-modeling, ignition and kinetics-modeling. Computational predictions of the aerodynamics of the single-injector were used to arrive at an optimized main-injector design that meets effective area and fuel-air mixing criteria. Emissions (EINOx) characteristics were predicted for a medium-power engine cycle condition, and will be compared with data when it is made available from experimental measurements. The use of a PDF-like turbulence-chemistry interaction model with NCC's Time-Filtered Navier-Stokes (TFNS) solver is shown to produce a significant impact on the CFD results, when compared with a laminar-chemistry TFNS approach for the five-injector computations.

combustion chambers↗

U.S. IMERG Status

The U.S. Science Team’s Integrated Multi-satellitE Retrievals for the Global Precipitation Measurement (GPM) mission (IMERG) product provides estimates of surface precipitation rate and related information on a global 0.1° half-hour grid. It is run three times at increasingly longer latency and higher information input to serve different communities. This presentation will briefly summarize the major upgrades included in Version 07. The Goddard Profiling (GPROF) algorithm (applied to passive microwave sensor data from the GPM virtual constellation) and the Combined Radar-Radiometer Algorithm (CORRA) that provide input to IMERG V07 are both improved, and the new Precipitation Estimation from Remotely Sensed Information Using Artificial Neural Networks–Dynamic Infrared Rain Rate (PDIR) algorithm is being applied to infrared data, which employs an additional, warmer infrared temperature threshold than the previous infrared scheme and a deep neural network. V07 has improved bias performance as a result of calibrations that now employ the entire swath widths of CORRA and GPROF GPM Microwave Imager precipitation estimates. As well, time continuity in precipitation features is improved as a result of changes to the Kalman filter that approximately preserve the local histogram of precipitation rates (Scheme for Histogram Adjustment with Ranked Precipitation Estimates in the Neighborhood, or SHARPEN), and that better account for differences in sensor performance. A long-standing bug in the geolocation that shifted grid values 0.1° to the east in the latitude band 70°N-S has been corrected. Other changes in V07 include a hierarchical selection among motion vector sources to address deficiencies in the precipitation propagation near orography, an update to the precipitation phase specification for improved consistency with current inputs, and a renewed effort to implement climatological gauge adjustment to the near-real-time Runs. Early evaluations of V07 IMERG show interesting behavior across the TRMM orbit boost that is highly relevant to the planned orbit boost for the GPM Core observatory.

GPM↗

FIRST MEASUREMENTS OF THE MASS OF CORONAL MASS EJECTIONS FROM THE EUV DIMMING OBSERVED WITH STEREO EUVI A+B SPACECRAFT

The masses of coronal mass ejections (CMEs) have traditionally been determined from white-light coronagraphs (based on Thomson scattering of electrons), as well as from extreme ultraviolet (EUV) dimming observed with one spacecraft. Here we develop an improved method of measuring CME masses based on EUV dimming observed with the dual STEREO/EUVI spacecraft in multiple temperature filters that includes three-dimensional volume and density modeling in the dimming region and background corona. As a test, we investigate eight CME events with previous mass determinations from STEREO/COR2, of which six cases are reliably detected with the Extreme Ultraviolet Imager (EUVI) using our automated multi-wavelength detection code. We find CME masses in the range of m {sub CME} = (2-7) x 10{sup 15} g. The agreement between the two EUVI/A and B spacecraft is m{sub A} /m{sub B} = 1.3 +- 0.6 and the consistency with white-light measurements by COR2 is m{sub EUVI}/m{sub COR2} = 1.1 +- 0.3. The consistency between EUVI and COR2 implies no significant mass backflows (or inflows) at r < 4 R{sub sun} and adequate temperature coverage for the bulk of the CME mass in the range of T approx 0.5-3.0 MK. The temporal evolution of the EUV dimming allows us to also model the evolution of the CME density n{sub e} (t), volume V(t), height-time h(t), and propagation speed v(t) in terms of an adiabatically expanding self-similar geometry. We determine e-folding EUV dimming times of t{sub D} = 1.3 +- 1.4 hr. We test the adiabatic expansion model in terms of the predicted detection delay (DELTAt approx 0.7 hr) between EUVI and COR2 for the fastest CME event (2008 March 25) and find good agreement with the observed delay (DELTAt approx 0.8 hr).

79 ASTRONOMY AND ASTROPHYSICS↗

Iron dissolution from Patagonian dust in the Southern Ocean: under present and future conditions

Although the input of desert dust as a key source of trace metals in the Southern Ocean (SO) has been previously studied, the dissolution process of metals in surface waters, particularly iron (Fe), remain poorly understood. Given the crucial role of Fe in primary production and the biological carbon pump in the SO, we focused on experimental estimations of Fe dissolution from Patagonian dust, the primary natural dust source in the SO. Our study considered both current and projected future conditions, encompassing sea-surface warming, acidification, increased photosynthetically active radiation, and doubled dust inputs. Through controlled laboratory experiments using filtered SO seawater, conducted over 7 days, we assessed changes in particulate Fe (pFe) concentrations, Fe redox speciation (Fe(II)/Fe(III)), and in the mineralogy of Fe-bearing dust in abiotic condition. The predominant minerals in the dust included quartz and aluminosilicates, with silicon (Si), aluminum (Al), and Fe as the major elements. No significant alterations in the mineralogy and the elemental composition of the dust were recorded during the dissolution experiments, neither under present nor under projected future conditions. The particulate Fe(II)/Fe(III) ratio remained consistently at 0.25 during the experiments, unaffected by changed conditions. Consequently, changes in environmental conditions in the SO would therefore not significantly alter the mineralogy and redox speciation of pFe in the Patagonian dust. On the contrary, pFe exhibited a dissolution rate of 3.8% and 1.6% per day under present and future conditions, respectively. The environmental changes anticipated for 2100 in the SO will likely to result in a decrease in the dissolution rate of pFe. Thus, even though a doubling of dust input by 2100 is anticipated, it will unlikely provide significantly more dissolved Fe (dFe) in seawater in the SO. Consequently, the future intensification of Patagonian dust inputs may not alleviate the Fe limitation in the SO.

54 ENVIRONMENTAL SCIENCES↗