Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stokes flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Thermodynamic evaluation of transonic compressor rotors using the finite volume approach

A method was developed which calculates two-dimensional, transonic, viscous flow in ducts. The finite volume, time marching formulation is used to obtain steady flow solutions of the Reynolds-averaged form of the Navier Stokes equations. The entire calculation is performed in the physical domain. The method is currently limited to the calculation of attached flows. The features of the current method can be summarized as follows. Control volumes are chosen so that smoothing of flow properties, typically required for stability, is now needed. Different time steps are used in the different governing equations to improve the convergence speed of the viscous calculations. A new pressure interpolation scheme is introduced which improves the shock capturing ability of the method. A multi-volume method for pressure changes in the boundary layer allows calculations which use very long and thin control volumes. A special discretization technique is also used to stabilize these calculations. A special formulation of the energy equation is used to provide improved transient behavior of solutions which use the full energy equation. The method is then compared with a wide variety of test cases. The freestream Mach numbers range from 0.075 to 2.8 in the calculations. Transonic viscous flow in a converging diverging nozzle is calculated with the method; the Mach number upstream of the shock is approximately 1.25. The agreement between the calculated and measured shock strength and total pressure losses is good. Essentially incompressible turbulent boundary layer flow in a adverse pressure gradient is calculated and the computed distribution of mean velocity and shear stress are in good agreement with the measurements. At the other end of the Mach number range, a flat plate turbulent boundary layer with a freestream Mach number of 2.8 is calculated using the full energy equation; the computed total temperature distribution and recovery factor agree well with the measurements when a variable Prandtl number is used through the boundary layer.

Nicholson, S.↗
NASA NTRS1986

Numerical solution of the separating flow due to an obstruction

The steady separated flow due to an obstruction in a two-dimensional channel is studied through the numerical solution of the Navier-Stokes equations using finite difference techniques. The characteristics of the separated flow behind the obstruction are obtained up to a Reynolds number of 1500. The flow patterns, vorticity contours and total pressure contours are presented. The effects of Reynolds number, height of obstruction, thickness of obstruction and the inlet velocity profile are investigated.

Nallasamy, M.↗
NASA NTRS1993

Effects of spatial order of accuracy on the computation of vortical flowfields

The effect of the order-of-accuracy, used for the spatial discretization, on the resolution of the leading edge vortices over sharp-edged delta wings is investigated. The flowfield is computed using a viscous/inviscid zonal approach. The viscous flow in the vicinity of the wing is computed using the conservative formulation of the compressible, thin-layer Navier-Stokes equations. The leeward-side vortical flowfield and the other flow regions away from the surface are computed as inviscid. The time integration is performed with both an explicit fourth-order Runge-Kutta scheme and an implicit, factorized, iterative scheme. High-order-accurate inviscid fluxes are computed using both a conservative and a non-conservative (primitive variable) formulation. The nonlinear, inviscid terms of the primitive variable form of the governing equations are evaluated with a finite-difference numerical scheme based on the sign of the eigenvalues. High-order, upwind-biased, finite difference formulas are used to evaluate the derivatives of the nonlinear convective terms. Computed results are compared with available experimental data, and comparisons of the flowfield in the vicinity of the vortex cores are presented.

Ekaterinaris, J. A.↗
NASA NTRS1983

Three-dimensional viscous-flow computations using a directionally hybrid implicit-explicit procedure

A new, directionally dependent, hybrid numerical algorithm for solving the unsteady, three-dimensional Navier-Stokes equations has been developed and used to compute the viscous supersonic flow over complex configurations, which may generate local regions of embedded subsonic or streamwise separated flows or both. The new hybrid implicit-explicit algorithm is derived from the more general implicit Beam-Warming algorithm and is particularly suitable for viscous computations in which the grid spacing in the direction outward from the body is considerably smaller than the spacing in the other two directions. Numerical results obtained from both the hybrid and implicit schemes are presented and compared on the basis of numerical stability, convergence history, and computer and core memory requirements.

Rizk, Y. M.↗
NASA NTRS1993

A CFD-based aerodynamic design procedure for hypersonic wind-tunnel nozzles

A new procedure which unifies the best of current classical design practices, computational fluid dynamics (CFD), and optimization procedures is demonstrated for designing the aerodynamic lines of hypersonic wind-tunnel nozzles. The new procedure can be used to design hypersonic wind tunnel nozzles with thick boundary layers where the classical design procedure has been shown to break down. An efficient CFD code, which solves the parabolized Navier-Stokes (PNS) equations using an explicit upwind algorithm, is coupled to a least-squares (LS) optimization procedure. A LS problem is formulated to minimize the difference between the computed flow field and the objective function, consisting of the centerline Mach number distribution and the exit Mach number and flow angle profiles. The aerodynamic lines of the nozzle are defined using a cubic spline, the slopes of which are optimized with the design procedure. The advantages of the new procedure are that it allows full use of powerful CFD codes in the design process, solves an optimization problem to determine the new contour, can be used to design new nozzles or improve sections of existing nozzles, and automatically compensates the nozzle contour for viscous effects as part of the unified design procedure. The new procedure is demonstrated by designing two Mach 15, a Mach 12, and a Mach 18 helium nozzles. The flexibility of the procedure is demonstrated by designing the two Mach 15 nozzles using different constraints, the first nozzle for a fixed length and exit diameter and the second nozzle for a fixed length and throat diameter. The computed flow field for the Mach 15 least squares parabolized Navier-Stokes (LS/PNS) designed nozzle is compared with the classically designed nozzle and demonstrates a significant improvement in the flow expansion process and uniform core region.

Korte, John J.↗
DOE OSTI2024

Numerical simulation of involute-plate research reactor flow behavior using RANS, LES and DNS

This paper investigates the flow behavior of involute-plate research reactors by performing Reynolds-Averaged Navier Stokes simulation (RANS), Large Eddy Simulation (LES) and Direct Numerical Simulation (DNS) of the channel flow between fuel plates. By modeling turbulence with different numerical approaches, this study provides data with three levels of fidelity. For the RANS simulation, three widely used turbulence models, i.e., k-ε, k-ω, Reynolds Stress Turbulence model (RST) are applied by using the commercial CFD code STAR-CCM +. For LES and DNS, the open-source CFD code, Nek5000, is used given its outstanding scalability on High Performance Computer (HPC) and high-order technique. The results from RANS simulations are compared with that from LES and DNS for benchmarking. Both macroscale parameters and turbulence statistics, such as velocity magnitude, lateral velocity and turbulence kinetic energy, are presented and analyzed. The results from RANS simulation achieve good agreement with LES and DNS on velocity and turbulence kinetic energy prediction. The RST turbulence model predicts the most similar flow pattern of lateral velocity as compared to LES and DNS. The Lambda-2 (λ2) criterion with a reasonable threshold is used to demonstrate the instantaneous vortices distribution in the involute channel from both LES and DNS calculation. The DNS simulation captures more detailed turbulence especially near the corner, which explains the discrepancy between LES and DNS results near the corner. The normalized RMS error are defined and calculated to assess the performance of those turbulence models. The RST model captures the anisotropic feature of turbulence, which enable it to outperform other turbulence models for predicting the flow behavior in an involute channel. Although some discrepancies are found between LES and DNS results in the corner, the overall deviations between LES and DNS are found to be small. In conclusion, given that the computational cost of DNS calculation is an order of magnitude higher, using LES data for benchmarking RANS model is a cost-effective approach.

DNS↗
NASA NTRS1979

A hybridized method for computing high-Reynolds-number hypersonic flow about blunt bodies

A hybridized method for computing the flow about blunt bodies is presented. In this method the flow field is split into its viscid and inviscid parts. The forebody flow field about a parabolic body is computed. For the viscous solution, the Navier-Stokes equations are solved on orthogonal parabolic coordinates using explicit finite differencing. The inviscid flow is determined by using a Moretti type scheme in which the Euler equations are solved, using explicit finite differences, on a nonorthogonal coordinate system which uses the bow shock as an outer boundary. The two solutions are coupled along a common data line and are marched together in time until a converged solution is obtained. Computed results, when compared with experimental and analytical results, indicate the method works well over a wide range of Reynolds numbers and Mach numbers.

Weilmuenster, K. J.↗
NASA NTRS1986

Vortical Flows Research Program of the Fluid Dynamics Research Branch

The research interests of the staff of the Fluid Dynamics Research Branch in the general area of vortex flows are summarized. A major factor in the development of enchanced maneuverability and reduced drag by aerodynamic means is the use of effective vortex control devices. The key to control is the use of emerging computational tools for predicting viscous fluid flow in close coordination with fundamental experiments. In fact, the extremely complex flow fields resulting from numerical solutions to boundary value problems based on the Navier-Stokes equations requires an intimate relationship between computation and experiment. The field of vortex flows is important in so many practical areas that a concerted effort in this area is justified. A brief background of the research activity undertaken is presented, including a proposed classification of the research areas. The classification makes a distinction between issues related to vortex formation and structure, and work on vortex interactions and evolution. Examples of current research results are provided, along with references where available. Based upon the current status of research and planning, speculation on future research directions of the group is also given.

Source record↗
NASA NTRS2017

An ODE-Based Wall Model for Turbulent Flow Simulations

Fully automated meshing for Reynolds-Averaged Navier-Stokes Simulations, Mesh generation for complex geometry continues to be the biggest bottleneck in the RANS simulation process; Fully automated Cartesian methods routinely used for inviscid simulations about arbitrarily complex geometry; These methods lack of an obvious & robust way to achieve near wall anisotropy; Goal: Extend these methods for RANS simulation without sacrificing automation, at an affordable cost; Note: Nothing here is limited to Cartesian methods, and much becomes simpler in a body-fitted setting.

Wall Model↗
NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper presents the results of an ongoing study into the linear stability characteristics of the boundary layer flow over the common research model with natural laminar flow (CRMNLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work involving parallel stability computations of a boundary layer flow based on the conical flow approximation has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien- Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. Here, we examine the effects of the simplifying approximations in both basic state computation and the stability analysis, with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, the basic states are computed by using full Navier-Stokes equations and the stability analysis is performed by using a nonorthogonal coordinate system that allows a clear distinction between planar TS and CF instabilities. Furthermore, the effects of curvature and nonparallel mean flow have been included in the stability computations based on the parabolized stability equations (PSE). The fully turbulent Reynolds-Averaged-Navier-Stokes (RANS) mean flow solutions show good agreement with the measured wall pressure distribution. Viscous-inviscid interactive effects are observed to be important because the shock fronts along the suction surface are influenced by the imposed transition front. The stability results confirm the previous findings related to TS amplification within the inboard region of the wing and the dominance of stationary CF modes in the outboard region. However, given the close proximity of the measured transition front and the dual shock system within the outer part of the wing, the onset of transition may well be shock limited within the outboard region. In general, the transition criterion based on the dual N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at Re MAC = 15 million and AoA = 1.5, 2 degrees; however, the low values of the correlating N-factors at Re MAC = 17.5 million support the hypothesis that the measured transition at the higher Reynolds number may have been strongly influenced by the merging of turbulent wedges that originate from surface imperfections near the leading edge.

Boundary layer transition↗
NASA NTRS1989

Three dimensional PNS solutions of hypersonic internal flows with equilibrium chemistry

An implicit procedure for solving parabolized Navier-Stokes equations under the assumption of a general equation of state for a gas in chemical equilibrium is given. A general and consistent approach for the evaluation of Jacobian matrices in the implicit operator avoids the use of unnecessary auxiliary quantities and approximations, and leads to a simple expression. Applications to two- and three-dimensional flow problems show efficiency in computer time and economy in storage.

Liou, May-Fun↗
NASA NTRS1991

Analytical methods for the development of Reynolds-stress closures in turbulence

The derivation of Reynolds-stress models for viscous incompressible turbulent flow on the basis of the Navier-Stokes and continuity equations is explored in an analytical review. The formulation of the basic equations is outlined, and particular attention is given to zero-equation and one-equation models based on eddy viscosity, two-equation (k-l, k-epsilon, and k-omega) models, and second-order closure models. The superior performance of the second-order models is demonstrated by numerical results for (1) the return to isotropy from anisotropic homogeneous turbulence, (2) homogeneous turbulent shear flow in a rotating frame, (3) and fully developed inhomogeneous turbulent channel flow in a rotating frame. The inherent limitations of the Reynolds-stress approach and areas for further improvement are discussed.

Speziale, Charles G.↗
NASA NTRS1988

Multi-airfoil Navier-Stokes simulations of turbine rotor-stator interaction

An accurate numerical analysis of the flows associated with rotor-stator configurations in turbomachinery can be extremely helpful in optimizing the performance of turbomachinery. In this study the unsteady, thin-layer, Navier-Stokes equations in two spatial dimensions are solved on a system of patched and overlaid grids for a rotor-stator configuration from an axial turbine. The governing equations are solved using a finite-difference, upwind algorithm that is set in an iterative, implicit framework. Results in the form of pressure contours, time-averaged pressures, unsteady pressure amplitudes and phase are presented. The numerical results are compared with experimental data and the agreement is found to be good. The results are also compared with those of an earlier study which used only one rotor and one stator. The current study uses multiple rotors and stators and a pitch ratio that is much closer to the experimental ratio. Consequently the results of this study are found to be closer to the experimental data.

Rai, Man Mohan↗
NASA NTRS1986

Numerical simulation of transitional flow

The applicability of active control of transition by periodic suction-blowing is investigated via direct simulations of the Navier-Stokes equations. The time-evolution of finite-amplitude disturbances in plane channel flow is compared in detail with and without control. The analysis indicates that, for relatively small three-dimensional amplitudes, a two-dimensional control effectively reduces disturbance growth rates even for linearly unstable Reynolds numbers. After the flow goes through secondary instability, three-dimensional control seems necessary to stabilize the flow. An investigation of the temperature field suggests that passive temperature contamination is operative to reflect the flow dynamics during transition.

Biringen, Sedat↗
NASA NTRS1989

The 3-D Euler and Navier-Stokes calculations for aircraft components

An explicit multistage Runge-Kutta type of time-stepping scheme is used for solving transonic flow past a transport type wing/fuselage configuration. Solutions for both Euler and Navier-Stokes equations are obtained for quantitative assessment of boundary layer interaction effects. The viscous solutions are obtained on both a medium resolution grid of approximately 270,000 points and a find grid of 460,000 points to assess the effects of grid density on the solution. Computed pressure distributions are compared with the experimental data.

Vatsa, Veer N.↗
NASA NTRS1991

Simulations of curved turbulent boundary layers

The objective of this work is to develop a space-time accurate numerical method for the solution of incompressible Navier-Stokes equations in generalized coordinates. The resulting code is to be used for direct and large-eddy simulation of turbulence in complex geometries. In a previous paper, the system of Navier-Stokes equations in general curvilinear coordinates was solved by a second-order accurate finite-difference scheme. Satisfactory results were obtained for several flows in two and three dimensions. The system of Navier-Stokes for the fluxes are given in Orlandi (1989). The main deficiency of the numerical scheme was the large CPU time required for the solution of the Poisson equation for the 'pressure' field. The point SOR relaxation, in conjunction with a multigrid scheme, was used for the Poisson equation. In some cases, particularly with very fine grids, it was impossible to obtain a divergent-free flow. A preliminary attempt is made to compute the spatially evolving flow of Swearingen & Blackwelder. To reduce the streamwise distance, the inflow was at a distance x = 60 cm from the leading edge.

Orlandi, Paolo↗
NASA NTRS2018

Computational Investigation of Nominally-Orthogonal Pneumatic Active Flow Control for High-Lift Systems

We explore the feasibility of using nominally-orthogonal jets as active aerodynamic load control for multi-element high-lift systems, and whether the nominally-orthogonal jets can offer a variety of performance improvements. These nominally-orthogonal jets inject momentum normal to the airfoil surface near the flap trailing edge, where they create a vortex that entrains flow from the opposing side and change the airfoil circulation. Lift-enhancement opportunities of trailing edge nominally-orthogonal jets have previously been studied by Malavard et al. and Blaylock et al. on single-element airfoils; however, their effect on drag was not thoroughly investigated. In this study, we investigate two- dimensional nominally-orthogonal jet effects on both lift and drag on a two-element airfoil, NLR7301. We utilize Chimera Grid Tools to generate structured curvilinear overset grids, and the Reynolds-averaged Navier-Stokes solver OVERFLOW-2 to solve for the flow field around the airfoil. We perform various computational sensitivity studies on the baseline airfoil without a jet to validate computational results against benchmark experimental data. Using a Chimera overset grid topology, we demonstrate a similar lift-enhancement effect between a nominally-orthogonal jet and a nominally-orthogonal physical tab employed at the same location on the studied airfoil. After we introduce the nominally-orthogonal jet concept, we investigate nominally-orthogonal jets with various momentum coefficient settings, C(sub µ) = 0.00 − 0.04 and present a lift-enhancement relationship ∆C(sub l) ≃ 3.59 (C(sub µ)) for this airfoil. We discuss that utilizing a nominally-orthogonal jet with C(sub µ) = 0.01 can shift the linear region of the lift curve by a ∆C(sub l) = 0.36 for the pressure side jet and by a ∆C(sub l) = −0.27 for the suction side jet. Employing a nominally-orthogonal jet is also shown effective in altering the drag. To study the impact, we carry out a drag decomposition study in the form of drag polars. We show for a given C(sub l) = 2.50, a nominally-orthogonal jet with C(sub µ) = 0.01 on the pressure and suction side of the airfoil results in 113 drag count decrements and 41 drag count increments, respectively, compared to the baseline airfoil with no jet. These results show that large and controllable changes in aerodynamic performance can be achieved by relatively small active flow control inputs using the nominally-orthogonal jets presented in this study.

Nominally-Orthogonal↗