Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Unsteady aerodynamic behavior of an airfoil with and without a slat

Unsteady flow behavior and load characteristics of a 2D VR-7 airfoil with and without a leading-edge slat were studied in the water tunnel of the Aeroflightdynamics Directorate, NASA Ames Research Center. Both airfoils were oscillated sinusoidally between 5 and 25 deg at Re = 200,000 to obtain the unsteady lift, drag, and pitching moment data. A fluorescent dye was released from an orifice located at the leading edge of the airfoil for the purpose of visualizing the boundary layer and wake flow. The flowfield and load predictions of an incompressible Navier-Stokes code based on a velocity-vorticity formulation were compared with the test data. The test and predictions both confirm that the slatted VR-7 airfoil delays both static and dynamic stall as compared to the VR-7 airfoil alone.

Tung, Chee↗

Multielement airfoil performance due to Reynolds and Mach number variations

Experimental studies have been conducted to assess Reynolds and Mach number effects on a supercritical multielement airfoil. The airfoil is representative of the stall-critical station of an advanced transport wing design. The experimental work was conducted as part of a cooperative program between the Douglas Aircraft Company and the NASA Langley Research Center to improve current knowledge of high-lift flows and to develop a validation data base with practical geometries/conditions for emerging computational methods. This article describes results obtained for both landing and takeoff multielement airfoils (four- and three-element configurations) for a variety of Mach/Reynolds number combinations up to flight conditions. Effects on maximum lift are considered for the landing configurations, and effects on both lift and drag are reported for the takeoff geometry. The present test results revealed considerable maximum lift effects on the three-element landing configuration for Reynolds number variations, and significant Mach number effects on the four-element airfoil.

Valarezo, Walter O.↗

The Factors that Determine the Minimum Speed of an Airplane

The author argues that because of a general misunderstanding of the principles of flight at low speed, there are a large number of airplanes that could be made to fly several miles per hour slower than at present by making slight modifications. In order to show how greatly the wing section affects the minimum speed, curves are plotted against various loadings. The disposition of wings on the airplane slightly affects the lift coefficient, and a few such cases are discussed. Another factor that has an effect on minimum speed is the extra lift exerted by the slip stream on the wings. Also discussed are procedures to be followed by the pilot, especially with regard to stick movements during low speed flight. Also covered are stalling, yaw, rolling moments, lateral control, and the effectiveness of ailerons and rudders.

AIRPLANES - SPEED AND POWER AIRPLANE - SPEED↗

On the distribution of lift along the span of an airfoil with displaced ailerons

The effect of an aileron displacement on the distribution of the lift along the span is computed for an elliptic wing of aspect ratio 6 for three conditions. The lift distribution caused by the aileron displacement is uniform and extends normally beyond the inner end of the ailerons. Hence, the displacement of an aileron with constant chord length may bring about passing the stalling point of the adjacent wing sections, if these were near this point before. Hence, such ailerons can become ineffective at low speeds. Tapering the aileron towards the inside suggests itself as a remedy.

Munk, Max M↗

Wind tunnel pressure distribution tests on a series of biplane wing models Part II : effects of changes in decalage, dihedral, sweepback and overhang

This preliminary report furnishes information on the changes in the forces on each wing of a biplane cellule when the decalage, dihedral, sweepback and overhang are separately varied. The data were obtained from pressure distribution tests made in the Atmospheric Wind Tunnel of the Langley Memorial Aeronautical Laboratory. Since each test was carried up to 90 degree angle of attack, the results may be used in the study of stalled flight and of spinning and in the structural design of biplane wings.

Knight, Montgomery↗

Wind Tunnel Pressure Distribution Tests on a Series of Biplane Wing Models

This report is on the changes in forces on each wing of a biplane cellule when either the stagger or the gap is varied. Since each test was carried up to a 90 degree angle of attack, the results may be used in the study of stalled flight and of spinning as well as in the structural design of biplane wings.

Knight, Montgomery↗

Wind Tunnel Pressure Distribution Tests on a Series of Biplane Wing Models. Part III Effects of Charges in Various Combinations of Stagger, Gap, Sweepback, and Decalage

This preliminary report furnishes information on the changes in the forces on each wing of a biplane cellule for various combinations of stagger and gap, stagger and sweepback, stagger and decalage, and gap and decalage. The data were obtained from pressure distribution tests made in the atmospheric wind tunnel of the Langley Memorial Aeronautical Laboratory. Since each test was carried up to 90deg angle of attack, the results may be used in the study of stalled flight and of spinning as well as in the structural design of biplane wings.

Knight, Montgomery↗

The calculated effect of trailing-edge flaps on the take-off of flying boats

The results of take-off calculations are given for an application of simple trailing-edge flaps to two hypothetical flying boats, one having medium wing and power loading and consequently considerable excess of thrust over total resistance during the take-off run, the other having high wing and power loading and a very low excess thrust. For these seaplanes the effect of downward flap settings was: (1) to increase the total resistance below the stalling speed, (2) to decrease the get-away speed, (3) to improve the take-off performance of the seaplane having considerable excess thrust, and (4) to hinder the take-off of the seaplane having low excess thrust. It is indicated that flaps would allow a decrease in the high angles of wing setting necessary with most seaplanes, provided that the excess thrust is not too low.

Parkinson, J E↗

Aerodynamic characteristics of several airfoils of low aspect ratio

This paper presents the results of wind-tunnel tests of several airfoils of low aspect ratio. The airfoils included three circular Clark Y airfoils with different amounts of dihedral, two Clark Y airfoils with slots in their portions, and three flat-plate airfoils. Lift, drag, and pitching-moment characteristics of the slotted airfoils with slots open and closed; pitching moment characteristics of one of the slotted airfoils with slots open and closed; and lift characteristics of the flat-plate airfoils are included. The results reveal a definite improvement of lift, drag, and pitching-moment characteristics with increase in dihedral of the circular Clark Y wing. Lift characteristics near the stall were found to depend markedly on the shape of the extreme tip but were not greatly affected by slots through the after portion of the airfoils. Changes in plan form of the flat-plate airfoils gave erroneous indications of the effect to be expected from changes in plan form of an airfoil of Clark Y section. The minimum drag characteristics of the circular Clark Y airfoils were found to be substantially the same as for a Clark Y airfoil of conventional aspect ratio.

Zimmerman, C H↗

The Effect of Split Trailing-edge Wing Flaps on the Aerodynamic Characteristics of a Parasol Monoplane

This paper presents the results of tests conducted in the N.A.C.A. full-scale wind tunnel on a Fairchild F-22 airplane equipped with a special wing having split trailing-edge flaps. The flaps extended over the outer 90 percent of the wing span, and were of the fixed-hinge type having a width equal to 20 percent of the wing chord. The results show that with a flap setting of 59 degrees the maximum lift of the wing was increased 42 percent, and that the flaps increased the range of available gliding angles from 2.7 degrees to 7.0 degrees. Deflection of the split flaps did not increase the stalling angle or seriously affect the longitudinal balance of the airplane. With flaps down the landing speed of the airplane is decreased, but the calculated climb and level-flight performance is inferior to that with the normal wing. Calculations indicate that the take-off distance required to clear an obstacle 100 feet high is not affected by flap settings from 0 degrees to 20 degrees but is greatly increased by larger flap angles.

TAKE-OFF & LANDING - EFFECT OF WING FLAPS↗

Wind tunnel research comparing lateral control devices, particularly at high angles of attack XI : various floating tip ailerons on both rectangular and tapered wings

Discussed here are a series of systematic tests being conducted to compare different lateral control devices with particular reference to their effectiveness at high angles of attack. The present tests were made with six different forms of floating tip ailerons of symmetrical section. The tests showed the effect of the various ailerons on the general performance characteristics of the wing, and on the lateral controllability and stability characteristics. In addition, the hinge moments were measured for the most interesting cases. The results are compared with those for a rectangular wing with ordinary ailerons and also with those for a rectangular wing having full-chord floating tip ailerons. Practically all the floating tip ailerons gave satisfactory rolling moments at all angles of attack and at the same time gave no adverse yawing moments of appreciable magnitude. The general performance characteristics with the floating tip ailerons, however, were relatively poor, especially the rate of climb. None of the floating tip ailerons entirely eliminated the auto rotational moments at angles of attack above the stall, but all of them gave lower moments than a plain wing. Some of the floating ailerons fluttered if given sufficiently large deflection, but this could have been eliminated by moving the hinge axis of the ailerons forward. Considering all points including hinge moments, the floating tip ailerons on the wing with 5:1 taper are probably the best of those which were tested.

Weick, Fred E↗

Development of the NACA slot-lip aileron

An investigation of the undesirable delayed action, or lag, of the spoiler-type lateral control device led to the development of the NACA slot-lip aileron. The tests were made in the 7- by 10-foot wind tunnel with a 4- by 8-foot wing hinged at the tunnel jet boundary and taken of the motion of the control device under test and of the resulting wing motion. First, the lag, as affected by the fore-and-aft location of retractable ailerons or spoilers was determined. The lag was found to increase regularly as the spoiler was moved from the rear of the wing toward the front. Then a combination of spoilers and fixed slot was developed that, with the spoiler retracting into the forward part of the slot, reduced the time lag to a negligible value. In addition, an arrangement was developed using a hinged aileron-type flap as the upper portion, or lip, of a slot through the wing. This arrangement appears to be usable as a form of lateral control device that shows promise of giving improved control and stability at the high angles of attack through stall, with negligible lag, low control forces, and relatively simple construction.

Weick, Fred E↗

Notes on the technique of landing airplanes equipped with wing flaps

The proper landing of airplanes equipped with flaps, although probably no more difficult than landing without them, requires a different technique. The effects of flaps on the aerodynamics characteristics of a wing are given and, with the aid of figures and diagrams, a detailed comparison of the glide and landing of an airplane with and without flaps is made. The dangers attending improper execution and the importance of such factors as air speed fuselage attitude, glide-path angle, and control manipulation, upon all of which a pilot bases his judgement, are emphasized. Of most importance in connection with the use of flaps are: the maintenance of a sufficient margin of speed above the stall; a decisive use of the controls at the proper time; more cautious use of power during the approach glide; and, above all, the willingness to accept the steep nose-down attitude necessary in the glide resulting from the use of flaps.

Gough, Melvin N↗

The calculation of span LCAD distributions of swept-back wings

Span load distributions of swept-back wings have been calculated. The method used was to replace the wing with a bound vortex at the quarter-chord line and to calculate the downwash due to the system of bound and trailing vortices to conform at the three-quarter-chord line to the slope of the flat-plate wing surface. Results are given for constant-chord and 5:1 tapered plan forms, for sweep-back angles of 0 degrees, 30 degrees, and 45 degrees, and for aspect ratios of 3, 6, and 9. Some comments on the stalling of swept-back wings are included.

Mutterperl, William↗

Investigation of a Spoiler-Type Lateral Control System on a Wing with Full-Span Flaps in the Langley 19-Foot Pressure Tunnel

Tests of a partial-span model of a large bomber-type air1ane were conducted to determine the. aerodynamic characteristics of the wing equipped with full-span flaps and a retractable spoiler end aileron lateral control system. The arrangement consisted of (1) a double slotted flap extending over aproximate1y 86 percent of the wing semispan, (2) a 20-percent constant-percentage-chord aileron extending from the outboard end of the flap to the wing tip, and (3) a retractable spoiler, located at the 65-percent wing-chord station and extending from approximately 63 percent of the wing semispan to the wing tip. In addition, tests were made of a wing vent (of 1 and 2 percent of the wing chord located directly behind the spoiler), perforations in the spoiler, a blot or cut-out along the lower edge of the spoiler and spoilers of various spans. With full-span flaps deflected and with the 2-percent vent open or closed the initial stalling of the wing occurred at the tips, but with the vents closed there probably would be no appreciable loss in lateral control until maximum lift was reached. The l-percent vent increased the rolling effectiveness of the spoiler at small spoi1er deflections, particularly at high angles of attack with flaps deflected. With flaps deflected the 2-percent vent caused a large reduction in both the wing lift and rolling effectiveness of the spoiler at large angles of attack. However, at small angle of attack the 2-percent vent increased the rolling effectiveness of the spoiler at small spoiler deflections. The simultaneous operation of the spoiler and vent (in contrast to a vent fixed in the wing) would result in a large increase in the effectiveness of the spoiler and would avoid any loss in wing lift as in a fixed vent arrangement. The tests of the spoiler modifications revealed that (1) the spoiler perforations reduced the rolling-moment and yawing-moment coefficients but caused the spoiler hinge-moment coefficients to become more positive; (2) the spoiler slot had no notable effect on the rolling-moment and yawing-moment characteristics but produced a positive increase in the spoiler hinge-moment coefficients at large spoiler deflections; (3) the effects produced by the individual modifications were additive when the various modifications were combined. In general, progressively decreasing the spoiler span by removing the segments from the inboard end of the spoiler caused a decrease in rolling effectiveness approximately proportional to the span of the segment.

WING FLAPS, SLOTTED & AILERONS↗

An Analysis of the Autorotative Performance of a Helicopter Powered by Rotor-Tip Jet Units

The autorotative performance of an assumed helicopter was studied to determine the effect of inoperative jet units located at the rotor-blade tip on the helicopter rate of descent. For a representative ramjet design, the effect of the jet drag is to increase the minimum rate of descent of the helicopter from about 1,OO feet per minute to 3,700 feet per minute when the rotor is operating at a tip speed of approximately 600 feet per second. The effect is less if the rotor operates at lower tip speeds, but the rotor kinetic energy and the stall margin available for the landing maneuver are then reduced. Power-off rates of descent of pulse-jet helicopters would be expected to be less than those of ramjet. helicopters because pulse jets of current design appear to have greater ratios of net power-on thrust to power-off, drag than currently designed rain jets. Iii order to obtain greater accuracy in studies of autorotative performance, calculations in'volving high power-off rates of descent should include the weight-supporting effect of the fuselage parasite-drag force and the fact that the rotor thrust does not equal the weight of the helicopter.

AUTOROTATION↗

Effect of Ground Interference on the Aerodynamic Characteristics of a 42 Degrees Sweptback Wing

The effects of ground interference on the aerodynamic characteristics of a 42 degrees sweptback wing have been determined at distances above the ground 0.68 and 0.92 of the mean aerodynamic chord (measured from the 0.25 mean aerodynamic chord). The wing was tested without flaps and with inboard trailing-edge split and outboard leading-edge flaps deflected. The wing had an aspect ratio of 4, a taper ratio of 0.625, and NACA 641-112 airfoil sections perpendicular to the 0.273 chord line. The results are, in general, comparable to those reported for unswept wings. The longitudinal stability at the stall was not materially affected at the ground heights of the present tests.

RESEARCH TECHNIQUE, AERODYNAMICS↗

Accelerations and Passenger Harness Loads Measured in Full-Scale Light-Airplane Crashes

Full-scale light-airplane crashes simulating stall-spin accidents were conducted to determine the decelerations to which occupants are exposed and the resulting harness forces encountered in this type of accident. Crashes at impact speeds from 42 to 60 miles per hour were studied. The airplanes used were of the familiar steel-tube, fabric-covered, tandem, two-seat type. In crashes up to an impact speed of 60 miles per hour, crumpling of the forward fuselage structure prevented the maximum deceleration at the rear-seat location from exceeding 26 to 33g. This maximum g value appeared independent of the impact speed. Restraining forces in the seatbelt - shoulder-harness combination reached 5800 pounds. The rear-seat occupant can survive crashes of the type studied at impact speeds up to 60 miles per hour, if body movement is restrained by an adequate seatbelt-shoulder-harness combination so as to prevent injurious contact with obstacles normally present in the cabin. Inwardly collapsing cabin structure, however, is a potential hazard in the higher-speed crashes.

Eiband, A. Martin↗