Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Exchange bias mediated by interfacial nanoparticles (invited)

The objective of this study on the iconic exchange-bias bilayer Permalloy/CoO has been to identify those elements of the interfacial microstructure and accompanying magnetic properties that are responsible for the exchange-bias and hysteretic properties of this bilayer. Both epitaxial and polycrystalline samples were examined. X-ray and neutron reflectometry established that there existed an interfacial region, of width ∼1 nm, whose magnetic properties differed from those of Py or CoO. A model was developed for the interfacial microstructure that predicts all the relevant properties of this system; namely; the temperature and Permalloy thickness dependence of the exchange-bias, H{sub EX}, and coercivity, H{sub C}; the much smaller measured values of H{sub EX} from what was nominally expected; the different behavior of H{sub EX} and H{sub C} in epitaxial and polycrystalline bilayers. A surprising result is that the exchange-bias does not involve direct exchange-coupling between Permalloy and CoO, but rather is mediated by CoFe{sub 2}O{sub 4} nanoparticles in the interfacial region.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

New alnico magnets fabricated from pre-alloyed gas-atomized powder through diverse consolidation techniques

Fine Alnico 8 spherical powder produced by gas atomization was consolidated through hot pressing (HP), hot isostatic pressing (HIP), and compression molding and subsequent sintering (CMS) techniques. The effects of different fabrication techniques and processing parameters on microstructure and magnetic properties were analyzed and compared. The HP, HIP, and CMS magnets exhibited different features in microstructures and magnetic properties. Magnetically annealed at 840°C for 10 min and subsequently tempered at 650°C for 5h and 580°C for 15h, the HIP sample achieved the best coercivity (H cj =1845 Oe) due to spinodally decomposed (SD) phases with uniform and well-faceted mosaic morphology. As a result, the CMS sample had a lower Hcj than HIP and HP samples, but a higher remanence and thus the best energy product (6.5 MGOe) due to preferential grain alignment induced by abnormal grain growth.

36 MATERIALS SCIENCE↗

Process design of press hardening with gradient material property influence

Press hardening is currently used in the production of automotive structures that require very high strength and controlled deformation during crash tests. Press hardening can achieve significant reductions of sheet thickness at constant strength and is therefore a promising technology for the production of lightweight and energy-efficient automobiles. The manganese-boron steel 22MnB5 have been implemented in sheet press hardening owing to their excellent hot formability, high hardenability, and good temperability even at low cooling rates. However, press-hardened components have shown poor ductility and cracking at relatively small strains. A possible solution to this problem is a selective increase of steel sheet ductility by press hardening process design in areas where the component is required to deform plastically during crash tests. To this end, process designers require information about microstructure and mechanical properties as a function of the wide spectrum of cooling rates and sequences and austenitizing treatment conditions that can be encountered in production environments. In the present work, a Continuous Cooling Transformation (CCT) diagram with corresponding material properties of sheet steel 22MnB5 was determined for a wide spectrum of cooling rates. Heating and cooling programs were conducted in a quenching dilatometer. Motivated by the importance of residual elasticity in crash test performance, this property was measured using a micro-bending test and the results were integrated into the CCT diagrams to complement the hardness testing results. This information is essential for the process design of press hardening of sheet components with gradient material properties.

36 MATERIALS SCIENCE↗

Optimization of chemical compositions in low-carbon Al-killed enamel steel produced by ultra-fast continuous annealing

The influence of Mn,S and B contents on microstructural characteristics, mechanical properties and hydrogen trapping ability of low-carbon Al-killed enamel steel was investigated. The materials were produced and processed in a laboratory and the ultra-fast continuous annealing processing was performed using a continuous annealing simulator. It was found that increasing Mn,S contents in steel can improve its hydrogen trapping ability which is attributed by refined ferrite grains, more dispersed cementite and added MnS inclusions. Nevertheless, it deteriorates mechanical properties of steel sheet. Addition of trace boron results in both good mechanical properties and significantly improved hydrogen trapping ability. The boron combined with nitrogen segregating at grain boundaries, cementite and MnS inclusions, provides higher amount of attractive hydrogen trapping sites and raises the activation energy for hydrogen desorption from them. - Highlights: • We study microstructures and properties in low-carbon Al-killed enamel steel. • Hydrogen diffusion coefficients are measured to reflect fish-scale resistance. • Manganese improves hydrogen trapping ability but decrease deep-drawing ability. • Boron improves both hydrogen trapping ability and deep-drawing ability. • Both excellent mechanical properties and fish-scale resistance can be matched.

36 MATERIALS SCIENCE↗

Elaborating the phases and mechanical properties of multiphase alloy: Experimental two-dimensional mapping combined with theoretical calculations

Highlights: • Mechanical modulus and hardness distribution mapping is obtained for the first time by NanoBlitz 3D. • Phases mapping and exact element ratio are characterized for the nano multielement carbides by EPMA. • Carbides types are confirmed by acid etching and XRD refinement. • Young's modulus of multiple carbides is verified by DFT calculations and Voigt-Reuss-Hill model. - Abstract: The relationship between types of phases, microstructure and mechanical properties is always a critical challenge for the research and application of multiphase alloys. We report for the first time that NanoBlitz 3D method implemented in iNano is used to investigate the distribution of micro mechanical modulus and hardness for the entire complex multiphase alloy Fe-6.0W-5.0Mo-4.0Cr-2.0V-0.83C by constructing the two-dimensional mapping. In order to build the correlation between the microstructure and properties, the carbides in this tempering state steel are confirmed to be Fe{sub 3}(W, Mo){sub 3}C, Cr{sub 15.58}Fe{sub 7.42}C{sub 6} and V{sub 8}C{sub 7} by acid etching and XRD refinement. The phases mapping is obtained by electron probe micro-analysis. Exact element ratio is characterized for the nano-scale multielement carbides precipitates. The Young's modulus and hardness of the precipitated carbides are up to 330 GPa and 22 GPa, respectively. The distribution range of Young's modulus and hardness is during 150 to 250 GPa and 2.5 to 7.0 GPa for the matrix phases, respectively. The experimental Young's modulus and hardness results are verified by first-principles calculations combined with Voigt-Reuss-Hill approximation. In fact, this work provides a successful demonstration to three-dimensionally characterize the micro mechanical properties for all the ceramics and alloys.

36 MATERIALS SCIENCE↗

Machine-learning-assisted deciphering of microstructural effects on ionic transport in composite materials: A case study of Li 7 La 3 Zr 2 O 12 -LiCoO 2

The effective diffusivity of ionic species in multiphase materials is critical for the design and function of composite materials for electrochemical energy storage. In practice, effective diffusivity depends sensitively not only on the intrinsic diffusivities of constituting materials but also on their topological arrangement; nevertheless, these coupled contributions are oversimplified in most analytical models. Here, we combine atomistically informed mesoscale modeling and machine learning (ML) analysis to unravel how such features affect effective diffusivity in two-phase composites. Using the Li 7 La 3 Zr 2 O 12 -LiCoO 2 composite solid-state battery cathode as a model system, we compute effective diffusivity for 600 distinct dense polycrystalline microstructures with different topological configurations of grains, grain boundaries, and heterointerfaces. We verify that in addition to atomic-scale variabilities, microstructural feature diversity can significantly impact effective transport properties. Across the ensemble of test microstructures, this often results in bimodal distributions of effective diffusivity that encompass two qualitatively distinct operating mechanisms, which we identify via flux analysis. An ML approach reveals that the most critical determining factors for effective diffusivity are the connectivity of bulk phases and their heterointerfaces. The role of ionic mobility at the heterointerfaces is also discussed. These insights highlight the combined importance of microstructure and interface engineering in tuning the transport properties of ionic species in composite materials. In conclusion, our framework can also be extended for understanding generic microstructure-property relationships in other complex multiphase materials.

25 ENERGY STORAGE↗

Microstructural variation through weld thickness and mechanical properties of peened friction stir welded 6061 aluminum alloy joints

The current study examined the effect of microstructure variation on the development of mechanical properties in friction stir welded joints of 6061-T6 aluminum alloy, which were subsequently processed by shot peening (SP). Following to FSW, fatigue specimens were extracted perpendicularly to the welding direction. Surface Skimming to 0.5 mm from crown and root sides of the joint was made and SP was later applied on the two sides using ceramic shots of two different Almen intensities of 0.18 mmA and 0.24 mmA. Microstructural examination by electron back scattered diffraction (EBSD) indicated variation in the grain refinement of the weld zone, with coarsest grains (5 μm) at the crown side and finest grains (2 μm) at the root side. Reduction of microhardness to 60 HV occurred in the weld zone for samples in FSW condition. Application of SP promoted significant strain hardening at the crown side, with Almen intensities of 0.24 mmA providing maximum increase in microhardness to 120 HV. On the contrary, only a maximum microhardness of 75 HV was obtained at the root side. The difference in strain hardening capability at the two sides was strongly dependent on grain size. The two Almen intensities produced similar distribution of compressive residual stresses in the subsurface regions that led to enhance the fatigue strength to the level of base metal for N ≥ 10{sup 5} cycles. Yet, the increase in fatigue strength was more pronounced with increasing Almen intensity to 0.24 mmA, demonstrating further enhancement by strain hardening. - Highlights: • Grain refinement was observed after friction stir welding of AA 6061-T6. • Reduction in microhardness and fatigue strength were obtained after welding. • Variation in grain refinement led to different hardening behavior after peening. • Shot peening induced beneficial compressive residual stresses. • Shot peening and surface skimming markedly improved the fatigue performance.

36 MATERIALS SCIENCE↗

Strengthening mechanisms in directed energy deposited austenitic stainless steel

Microstructures and mechanical properties are evaluated in austenitic stainless steel structures fabricated by directed energy deposition (DED) considering the effects of applied loading orientation, build geometry, and distance from the deposition baseplate. Locations within an as-deposited build with different thermomechanical history display different yield strength, while those locations with similar history have approximately the same yield strength, regardless of test specimen orientation. Thermal expansion of deposited material near the baseplate is inhibited by the mechanical constraint imposed by the baseplate, promoting plastic deformation and producing a high density of dislocations. Concurrently, high initial cooling rates decrease away from the baseplate as the build is heated, causing an increased spacing of cellular solidification features. An analysis of strengthening mechanisms quantitatively established for the first time the important strengthening contribution of high dislocation densities in the materials (166–191 MPa) to yield strength that ranged from 438 to 553 MPa in the present DED fabricated structures. A newly adopted mechanistic relationship for microsegregation strengthening from the literature indicated an additional important contribution to strengthening (123–135 MPa) due to the cellular solidification features. These findings are corroborated by the measured evolution of microstructure and hardness caused by annealing the DED material. Finally, these results suggest that the mechanical properties of deposited austenitic stainless steels can be influenced by controlling thermomechanical history during the manufacturing process to alter the character of compositional microsegregation and the amount of induced plastic deformation.

36 MATERIALS SCIENCE↗

Effects of pyrolysis conditions on dielectric properties of PLZT films derived from a polyvinylpyrrolidone-modified sol-gel process

Graphical abstract: SEM images showing the surface morphology of PLZT films derived from solutions with various PVP content and treated with either RTA (rapid thermal annealing) or SPT (step-wise preheat treatment) process. Highlights: Black-Right-Pointing-Pointer High-quality PLZT films were fabricated by using a polyvinylpyrrolidone-modified sol-gel method. Black-Right-Pointing-Pointer Improved film density and integrity was achieved by employing a novel step-wise preheat treatment (SPT) process. Black-Right-Pointing-Pointer Enhanced dielectric properties were correlated to the improved microstructures as a result of the SPT process. -- Abstract: Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub 3} (PLZT) films were deposited on platinized silicon substrates (Pt/Si) using a polyvinylpyrrolidone (PVP) modified sol-gel method. Pyrolysis of the green films was conducted via two methods: rapid thermal annealing (RTA) and a step-wise preheat treatment (SPT). Microstructure analysis and dielectric property characterization were performed on samples treated by these two methods. Results showed that the SPT-pyrolyzed films exhibited much better dielectric properties when compared with the RTA-pyrolyzed films. The differences in dielectric properties were correlated to microstructural features caused by the different pyrolysis conditions. High-quality PLZT films with high dielectric constant ( Almost-Equal-To 860 at zero bias) and high breakdown strength ( Almost-Equal-To 2.1 MV/cm) were fabricated under controlled pyrolysis conditions. This work demonstrated the potential application of this material for power electronics in electric drive vehicles.

36 MATERIALS SCIENCE↗

Investigation of cellular microstructure and enhanced coercivity in sputtered Sm{sub 2}(CoCuFeZr){sub 17} film

We have investigated the effect of annealing temperature on the microstructure and magnetic properties of Sm{sub 2}(CoCuFeZr){sub 17} films prepared using ion beam sputtering at room temperature. The as-deposited film shows randomly oriented polycrystalline grains and exhibits small coercivity (H{sub C}) of 0.04 T at room temperature. Post annealing of these films at 700 °C under Ar atmosphere shows significant changes in the microstructure transforming it to the development of cellular growth, concomitant with enhanced coercivity up to 1.3 T. The enhanced coercivity is explained using the domain wall pinning mechanism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Additive Manufacturing of High-Entropy Alloys: A Review

Owing to the reduced defects, low cost, and high efficiency, the additive manufacturing (AM) technique has attracted increasingly attention and has been applied in high-entropy alloys (HEAs) in recent years. It was found that AM-processed HEAs possess an optimized microstructure and improved mechanical properties. However, no report has been proposed to review the application of the AM method in preparing bulk HEAs. Hence, it is necessary to introduce AM-processed HEAs in terms of applications, microstructures, mechanical properties, and challenges to provide readers with fundamental understanding. Specifically, we reviewed (1) the application of AM methods in the fabrication of HEAs and (2) the post-heat treatment effect on the microstructural evolution and mechanical properties. Compared with the casting counterparts, AM-HEAs were found to have a superior yield strength and ductility as a consequence of the fine microstructure formed during the rapid solidification in the fabrication process. The post-treatment, such as high isostatic pressing (HIP), can further enhance their properties by removing the existing fabrication defects and residual stress in the AM-HEAs. Furthermore, the mechanical properties can be tuned by either reducing the pre-heating temperature to hinder the phase partitioning or modifying the composition of the HEA to stabilize the solid-solution phase or ductile intermetallic phase in AM materials. Moreover, the processing parameters, fabrication orientation, and scanning method can be optimized to further improve the mechanical performance of the as-built-HEAs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An investigation of the microstructure and ductility of annealed cold-rolled tungsten

Tungsten is notoriously brittle metal at room temperature. Furthermore, contrary to most metals, plastic deformation increases ductility and recrystallization decreases ductility of tungsten. The fundamentals that govern this behavior have challenged academia and industry for decades. This paper focuses on understanding the controlling factors of ductility through a systematic investigation of the changes in microstructure and mechanical properties of cold-rolled tungsten that occur during annealing. Cold-rolled tungsten samples were annealed at temperatures up to 1400 °C, and mechanical testing and microstructural analysis was performed before and after annealing. Furthermore, a dislocation mobility model based on the Orowan equation was applied. The mechanisms of deformation are discussed within the context of deformed and annealed microstructures. The high fraction of low angle grain boundaries and high density of edge dislocations were found to be the most important factors for ductility. Although there were gradual changes in microstructure and mechanical properties, the ductility of cold-rolled tungsten was maintained up to 1300 °C. The material recrystallized when annealed above this temperature, had no ductility, and suffered brittle fracture. Microstructural characterizations of the as-rolled material revealed a typical BCC texture, with grains elongated in rolling direction and a large amount of edge dislocations and low angle grain boundaries. The level of texturing and the fraction of low angle grain boundaries diminished after recrystallization. It was found that, compared to the recrystallized material, as-rolled tungsten can accommodate over 7 orders of magnitude higher deformation velocity due to the high density of edge dislocations.

36 MATERIALS SCIENCE↗

Designing the Structure of Carbon Fibers for Optimal Mechanical Properties

Carbon fiber manufacturing follows generic processing steps: formation of thermoplastic fibers, stabilization, and carbonization. The final structures and end properties of the carbon fiber can differ significantly depending on the precursor chemistry and the associated processing sciences. Polyacrylonitrile (PAN) and mesophase pitch are the predominant precursors used in the production of carbon fibers. PAN-based carbon fibers consist of nanocrystalline graphitic domains typically 1.5 5 nm in size surrounded by amorphous carbon; in contrast, pitch-based carbon fibers are 10 50 nm crystallites with the graphitic (002) planes mostly aligned parallel to the fiber axis. It has been seen that the skin core structure of PAN-based carbon fibers plays a significant role in their mechanical properties. Designing a more homogenous carbon fiber microstructure by controlling the starting polymer and process parameters results in a different set of tensile strengths and elastic moduli. In this study the microstructural defect distribution (0.1 200 nm), measured by small-angle X-ray scattering, was shown to be directly related to the tensile strength of the carbon fibers. Here the formation of carbon structures from various polymer precursors is reviewed. Such a comprehensive understanding offers the opportunity to design carbon fiber microstructures with improved properties and to ultimately create new types of carbon fibers from alternative precursors at reduced cost.

Ozcan, Soydan↗

Mechanical properties of an Al 10 Nb 20 Ta 15 Ti 30 V 5 Zr 20 A2/B2 refractory superalloy and its constituent phases

Refractory superalloys (RSAs) are a new class of high-temperature structural materials consisting of a nanometer-sized mixture of two coherent A2 (disordered BCC) and B2 (ordered) phases. While these RSAs typically exhibit superior mechanical properties at elevated temperatures, they suffer from limited plasticity at lower temperatures, often attributed to the continuous ordered B2 matrix in these two-phase alloys. To knowledgably control the microstructure and mechanical properties of these alloys, the properties of the constitutive phases in RSAs should be known. Currently this information is absent. Here, in the present work, the microstructure and mechanical properties (at 20–1200 °C) of a candidate Al 0.5 NbTa 0.8 Ti 1.5 V 0.2 Zr RSA and two single-phase alloys, which compositions correspond to the compositions of the A2 and B2 phases in the selected RSA, are reported. Interestingly, and quite unexpectedly, the intrinsic mechanical behavior of the constituent A2 and B2 phases, deciphered for the first time in the present study, revealed that they are softer and substantially more ductile than the parent two-phase RSA. Furthermore, the ordered B2 phase exhibits a deformation twinning mechanism leading to twinning induced plasticity (TWIP) coupled with a low APB energy and activity of 1/2<111> dislocations. These mechanisms are thought to be responsible for the high plasticity of the ordered B2 phase. The results presented here question the current assumption that the ordered B2 phase in these RSAs has limited plasticity and strongly indicate that the nature of the B2/A2 interface boundaries and coherency strengthening play an important role in controlling the mechanical properties of the two-phase RSA.

36 MATERIALS SCIENCE↗

Microstructure and mechanical behavior of a TiC nanoprecipitate strengthened V Alloy

The V-4Cr-4Ti (V44) alloys have been proposed as the prime candidate structural material for self-cooled liquid Li blanket and other designs for fusion energy applications. However, the applications of the V44 alloy are limited to a narrow operation temperature window, due to reduction in creep strength at or above 700 °C and susceptibility to irradiation hardening and embrittlement when irradiated below 400 °C. Here, in this work, we explore the feasibility of designing a novel V alloy to form a high number density of TiC nanoprecipitates, in order to simultaneously improve creep strength and provide defect sinks to mitigate irradiation hardening. Computational thermodynamics was used to design a new alloy (V44C) to achieve our goal of high TiC nanoprecipitates density within the alloy V44 matrix. To ensure scalability, the new alloy was made through arc-melting and ingot-casting followed by hot forging, cold rolling and heat treatments of homogenization and precipitation aging. The microstructure was characterized by SEM, TEM, XRD and APT, confirming the existence of nanoprecipitates predicted in the thermodynamic calculations. In addition to microstructural evaluation tensile properties at room temperature and 700 °C, and Charpy impact energy at room temperature were measured. The microstructure and mechanical properties were then compared with those from a historic reference V44 alloy. The tensile strength improvement in V44C was rationalized based on particle and solid solution strengthening mechanism. The fracture behavior was discussed based on the fractography results and necking deformation behavior.

Alloys development↗

Modeling Of Microstructure Evolution Of BCC Metals Subjected To Severe Plastic Deformation

Prediction of microstructure evolution and properties of ultrafine-grained materials is one of the most significant, current problems in materials science. Several advanced methods of analysis can be applied for this issue: vertex models, phase field models, Monte Carlo Potts, finite element method (FEM) discrete element method (DEM) and finally cellular automata (CA). The main asset of the CA is ability for a close correlation of the microstructure with the mechanical properties in micro- and meso-scale simulation. Joining CA with the DEM undoubtedly improves accuracy of modeling of coupled phenomena during the innovative forming processes in both micro- and macro-scale. Deformation in micro-scale shows anisotropy, which connected with that the polycrystalline material contains grains with different crystallographic orientation, and grain deformation is depended from configuration of directions of main stresses and axis of grain. Then, CA and DEM must be joint solutions of crystal plasticity theory. In the present model, deformation in macro-scale is transferred to meso-sale, where a block contains several, score or hundreds grains, and then is applied in micro-scale to each grain. Creation of low-angle boundaries and their development into high-angle boundaries are simulated by the cellular automata on the base of calculations using finite element method and crystal plasticity theory. The idea proposed in this study and particular solutions are discussed for the case of ultrafine-grained low-carbon steel.

36 MATERIALS SCIENCE↗

Improvement of high-frequency characteristics of Z-type hexaferrite by dysprosium doping

Z-type hexaferrite has great potential applications as anti-EMI material for magnetic devices in the GHz region. In this work, Dy-doped Z-type hexaferrites with nominal stoichiometry of Ba{sub 3}Co{sub 2}Dy{sub x}Fe{sub 24-x}O{sub 41} (x 0.0, 0.05, 0.5, 1.0) were prepared by an improved solid-state reaction method. The effects of rare earth oxide (Dy{sub 2}O{sub 3}) addition on the phase composition, microstructure and electromagnetic properties of the ceramics were investigated. Structure and micromorphology characterizations indicate that certain content of Dy doping will cause the emergence of the second phase Dy{sub 3}Fe{sub 5}O{sub 12} at the grain boundaries of the majority phase Z-type hexaferrite, due to which the straightforward result is the grain refinement during the successive sintering process. Permeability spectra measurements show that the initial permeability reaches its maximum of 17 at 300 MHz with x = 0.5, while the cutoff frequency keeps above 800 MHz. The apparent specific anisotropy field H{sub K} of Dy-doped Z-type hexaferrites decreases with x increasing. The relationships among phase composition, grain size, permeability spectra, and anisotropy are theoretically investigated, and according to the analysis, Dy doping effects on its magnetic properties can be well explained and understood.

36 MATERIALS SCIENCE↗

Advanced characterization-informed machine learning framework and quantitative insight to irradiated annular U-10Zr metallic fuels

Abstract U-10Zr Metal fuel is a promising nuclear fuel candidate for next-generation sodium-cooled fast spectrum reactors. Since the Experimental Breeder Reactor-II in the late 1960s, researchers accumulated a considerable amount of experience and knowledge on fuel performance at the engineering scale. However, a mechanistic understanding of fuel microstructure evolution and property degradation during in-reactor irradiation is still missing due to a lack of appropriate tools for rapid fuel microstructure assessment and property prediction based on post irradiation examination. This paper proposed a machine learning enabled workflow, coupled with domain knowledge and large dataset collected from advanced post-irradiation examination microscopies, to provide rapid and quantified assessments of the microstructure in two reactor irradiated prototypical annular metal fuels. Specifically, this paper revealed the distribution of Zr-bearing secondary phases and constitutional redistribution across different radial locations. Additionally, the ratios of seven different microstructures at various locations along the temperature gradient were quantified. Moreover, the distributions of fission gas pores on two types of U-10Zr annular fuels were quantitatively compared.

36 MATERIALS SCIENCE↗