Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Laser Material Processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Random lasing in Nd{sup 3+} doped potassium gadolinium tungstate crystal powder

Random laser (RL) emission in Nd{sup 3+} doped potassium gadolinium tungstate—KGd(WO{sub 4}){sub 2}:Nd{sup 3+}—crystal powder is demonstrated. The powder was excited at 813 nm in resonance with the Nd{sup 3+} transition {sup 4}I{sub 9/2}→{sup 4}F{sub 5/2}. RL emission at 1067 nm due to the {sup 4}F{sub 3/2}→{sup 4}I{sub 11/2} transition was observed and characterized. An intensity threshold dependent on the laser spot area and bandwidth narrowing from ≈2.20 nm to ≈0.40 nm were observed and measured. For a beam spot area of 0.4 mm{sup 2}, a RL threshold of 6.5 mJ/mm{sup 2} (90 MW/cm{sup 2}) was determined. For excitation intensity smaller than the RL threshold, only spontaneous emission from level {sup 4}F{sub 3/2} with decay time in the tens microsecond range was observed, but for excitation above the RL threshold, significant shortening of excited level lifetime, characteristic of a stimulated process was found. The overall characteristics measured show that KGd(WO{sub 4}){sub 2}:Nd{sup 3+} is an efficient material for operation of solid state RLs in the near-infrared.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Sample preparation method for glass welding by ultrashort laser pulses yields higher seam strength

Glass welding by ultrashort laser pulses allows joining without the need of an absorber or a preheating and postheating process. However, cracks generated during the welding process substantially impair the joining strength of the welding seams. In this paper a sample preparation method is described that prevents the formation of cracks. The measured joining strength of samples prepared by this method is substantially higher than previously reported values.

36 MATERIALS SCIENCE↗

Accurate Quantification of Si/SiGe Interface Profiles via Atom Probe Tomography

Pulsed laser atom probe tomography (APT) has enabled the investigation of semiconducting materials at sub-nm length scales and 10 ppm chemical sensitivity. This has enabled APT to be the best technique for nanoscale detection of dopant distributions and low levels of chemical segregation at interfaces, which are both important for semiconductor processing; however, the accuracy of measured interfacial profiles is typically compromised by aberrations. Interfacial profiles in APT data will vary with respect to different interfacial combinations, especially when the evaporation field between two materials is drastically different. Here, the ability of APT to measure SiGe/Si/SiGe interfacial profiles is tested with an 8 nm Si well embedded in SiGe. The APT measurements are compared to those measured using scanning transmission electron microscopy (STEM) to evaluate reconstruction and post-reconstruction processing methods to appropriately measure interfacial profiles using APT. Without post-APT reconstruction processing, the measured Si/SiGe interfacial widths between APT and STEM match poorly, but after applying the z-redistribution algorithm, the interfacial profiles are in good agreement. These results indicate that APT can be used to accurately identify SiGe/Si/SiGe interfacial profiles after application of the z-redistribution algorithm, which will greatly impact the synergy between growth and characterization of semiconductor devices using Si/SiGe interfaces.

36 MATERIALS SCIENCE↗

Artificial intelligence driven laser parameter search: Inverse design of photonic surfaces using greedy surrogate-based optimization

Photonic surfaces designed with specific optical characteristics are becoming increasingly crucial for novel energy harvesting and storage systems. The design of these surfaces can be achieved by texturing materials using lasers. The optimal adjustment of laser fabrication parameters to achieve target surface optical properties is an open challenge. Thus, we develop a surrogate-based optimization approach. Our framework employs the Random Forest algorithm to model the forward relationship between the laser fabrication parameters and the resulting optical characteristics. During the optimization process, we use a greedy, prediction-based exploration strategy that iteratively selects batches of laser parameters to be used in experimentation by minimizing the predicted discrepancy between the surrogate model’s outputs and the user-defined target optical characteristics. This strategy allows for efficient identification of optimal fabrication parameters without the need to model the error landscape directly. We demonstrate the efficiency and effectiveness of our approach on two synthetic benchmarks and two specific experimental applications of photonic surface inverse design targets. By calculating the average performance of our algorithm compared to other state of the art optimization methods, we show that our algorithm performs, on average, twice as well across all benchmarks. Additionally, a warm starting inverse design technique for changed target optical characteristics enhances the performance of the introduced approach.

97 MATHEMATICS AND COMPUTING↗

Laser shock peening effect on the dislocation transitions and grain refinement of Al–Mg–Si alloy

This paper systematically investigates the effect of laser shock peening without coating parameters on the microstructural evolution, and dislocation configurations induced by ultra-high plastic strains and strain rates. Based on an analysis of optical microscopy, polarized light microscopy, transmission electron microscopy observations and residual stress analysis, the significant influence of laser shock peening parameters due to the effect of plasma generation and shock wave propagation has been confirmed. Although the optical microscopy results revealed no significant microstructural changes after laser shock peening, i.e. no heat effect zone and differences in the distribution of second-phase particles, expressive influence of laser treatment parameters on the laser shock induced craters was confirmed. Moreover, polarized light microscopy results have confirmed the existence of well-defined longish grains up to 455 μm in length in the centre of the plate due to the rolling effect, and randomly oriented smaller grains (20 μm × 50 μm) in the surface due to the static recrystallization effect. Laser shock peening is reflected in an exceptional increase in dislocation density with various configurations, i.e. dislocation lines, dislocation cells, dislocation tangles, and the formation of dense dislocation walls. More importantly, the microstructure is considerably refined due to the effect of strain deformations induced by laser shock peening process. The results have confirmed that dense dislocation structures during ultra-high plastic deformation with the addition of shear bands producing ultra-fine (60–200 nm) and nano-grains (20–50 nm). Furthermore, dislocation density was increased by a factor of 2.5 compared to the untreated material (29 × 10{sup 13} m{sup −2} vs. 12 × 10{sup 13} m{sup −2}). - Highlights: • LSPwC imparts high compressive residual stresses up to − 362 ± 31 MPa. • After LSPwC the microstructure is considerably refined via dislocation transitions. • Results confirmed ultra-fine (60–200 nm) and nano-grains (20–50 nm) after LSPwC. • Reasonable agreements between dislocation density and residual stress are obtained.

36 MATERIALS SCIENCE↗

Multimodal Nondestructive Dry Cask Basket Structure and Spent Fuel Evaluation

This NEUP-IRP assembled a team from diverse institutions and a diverse set of expertise to examine the problem of assessing the structural health of dry nuclear fuel storage casks, specifically the TN-32 design. With no physical access designed into these storage casks and the high cost and risk associated with opening casks for direct inspection, the technical difficulty of structural assessment of the basket structure and fuel assemblies is high. In response to this challenge, this IRP brought together experts in both traditional and novel NDE methodologies: active acoustics (University of Mississippi), emissions tomography (University of Florida), muon tomography (Oregon State University), and passive-active ultrasonics (University of South Carolina). Further, our industry partners in the Electric Power Research Institute (EPRI) and AREVA provided invaluable insight into technical design details for the cask, practical knowledge of operating parameters at a storage facility, and key relationships that enabled activities unforeseen at the time of the proposed work but were critical in guiding the path of the research. The team decided early in the project that we had a collective goal of laying the technical ground work for practical solutions that could be implemented in the field with reasonable cost, time, and reliability. A fortunate opportunity arose early in this IRP project to obtain access to a new TN-32 cask at Columbiana High Tech. Both acoustics teams were given access for testing concepts in the first year of the project. This ended up providing critical guidance in the design of subsequent laboratory experiments. Specifically, it became clear that the only reliable acoustic pathways to the interior were through the trunnions, base plate, and top ring of the cask. Based on these field tests and discussions about what would be of practical interest, the team as a whole decided a realistic goal was to detect catastrophic failure of a single fuel assembly, or one that was missing. It is clear from this work that the active acoustics / resonance and muon tomography methodologies would be capable of detecting interior structural integrity problems at this level. The other two areas of investigation (emissions tomography and passive/active ultrasonics) would need more testing to determine a successful implementation, but each may also have other applications such as long term monitoring and monitoring during transportation. This IRP project resulted in technical advances with applications that extend beyond the problem at hand, supported the training of 10 graduate students + 1 post doc, 21 publications, and 13 conference presentations. The remainder of this summary highlights significant activities and achievements in each of the methodologies and a brief discussion on how they can be combined to leverage strengths. Active Acoustics The active acoustics team at UM used both linear and non-linear structural resonance methods to infer information about the internal structure of a cask. Significant activities were a set of four field test measurements on a full scale TN-32 cask at the Columbiana Hi Tech facility in Greensboro, NC and the design and fabrication of a 1/6th scale model TN-32 cask for laboratory measurements. A significant set of acoustic data has been acquired on both the full scale and laboratory scale casks. It was determined early in the project that mechanical resonance techniques were not going to be sensitive to small scale (centimeter) cracks and structural defects in the basket structure or fuel assemblies. We were able to ascertain that both the energy and complexity of the resonance spectra were sensitive to “bulk state” of the fuel assemblies – an intact assembly versus a severely degraded assembly. By developing a novel combination of metrics, we are able to measure a statistically significant shift due to one out of the 32 fuel assemblies being either missing or degraded to a point of complete loss of structural coherence (i.e. “rubble”). We believe this combination of resonance metrics is new to the field and will have applications beyond the fuel storage problem. Emissions Tomography The Emissions Tomography team at the University of Florida explored the concept of using scattering of radiation emissions from the stored fuel as method of evaluating the internal structural health of the cask. Due to the need for emissive fuel assemblies and the difficulties of gaining access to storage facilities, this team primarily relied on simulations to inform feasibility. A key question was the flux estimates of neutrons with a small enough number of scattering events to retain spatial information. Some key conclusions from the transmission component of this work are that the number of scattering events falls rapidly with energy – setting a 11MeV threshold, the average number of scattering events is 8∓4. Rough estimates of scanning times using an ideal detector array would be 1 week. The team also explored the case of significant structural failure resulting in a shift of the source material (fuel). The result is that a +/- 2% mass shift results in a detectable (5.13%) shift in the correlated 2 neutron emission counts and thus may be a candidate as an initial survey. Finally, simulations for predicting the azimuthal dependence of the flux based on specific loading patterns were conducted. Due to self-shielding effects of the assemblies, a periodic pattern results and could potentially be used to identify missing or severely degraded assemblies. This work forms a basis for proper detector placement with the goal of optimizing sensitivity. Muon Tomography Muon tomography (MT) is a relatively novel method of interrogating interior structure on a large scale. One of the advantages of this technique is that the exciting energy source (cosmic muons) is ubiquitous and relatively stable in time. Challenging aspects are relatively low flux rates and appropriate detector technologies. The efforts of the muon group at Oregon State University focused on two areas: (1) simulation of various combinations of muon scattering events and detection schemes to assess sensitivities and time scales for image construction and (2) building a prototype muon detection system applicable to the dry storage cask problem as well as many other similar systems. Significant accomplishments in this area are: (1) demonstration that MT is a viable method for detecting missing or severely degraded rod assemblies, (2) a scintillation based detector with 4 panels and 32 channels of position data each were constructed, tested, and calibrated. Testing of the panels using natural muon background and no scattering objects yielded largely expected results – a straight line path for the muon through the four panels. However some anomalies (paths deviating from a line) were also detected. A redesign of the board improved the signal which greatly improved the muon tracking through the panels. Testing with lead bricks as scattering bodies showed a reduction in the coincidence rate with increasing bricks indicating increased scattering events. A refinement of the scintillator detector design resulted in a spatial image resolution of around 2 cm based on lead brick spacing tests lasting 24 hours. Passive/Active Ultrasonics This team at the University of South Carolina investigated the feasibility of combining passive ultrasonics, in which an elastic pulse is generated by a degradation process (such as a crack extending), and active ultrasonics, in which a known excitation is introduced into the structure and detected by an array of transducers. Significant accomplishments in this area include the development of elastic wave propagation simulation in relevant materials, development of diagnostic algorithms, and laboratory testing and validation using laser doppler vibrometry. This group demonstrated the applicability of various non-contact vibration detection methodologies such as air-coupled ultrasonic transducers and scanning laser doppler vibrometry. While passive acoustic emissions monitoring will likely have a role during the transportation of a fuel storage cask, the level of detailed information about the defect generating the event which can be ascertained from the detections in a complex structure remains for future work. Thermography The EPRI team contributed early in the project a series of thermography measurements in which various levels of water pooled in a mock-up canister were analyzed using commercially available infrared imaging technologies. While large levels of water (100 L, ~10 cm deep) were observable in the thermograms, more realistic levels of pooled water (1 L) were not detectable whether localized or distributed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of Advanced Low Conductivity Thermal Barrier Coatings

Advanced multi-component, low conductivity oxide thermal barrier coatings have been developed using an approach that emphasizes real-time monitoring of thermal conductivity under conditions that are engine-like in terms of temperatures and heat fluxes. This is in contrast to the traditional approach where coatings are initially optimized in terms of furnace and burner rig durability with subsequent measurement in the as-processed or furnace-sintered condition. The present work establishes a laser high-heat-flux test as the basis for evaluating advanced plasma-sprayed and electron beam-physical vapor deposited (EB-PVD) thermal barrier coatings under the NASA Ultra-Efficient Engine Technology (UEET) Program. The candidate coating materials for this program are novel thermal barrier coatings that are found to have significantly reduced thermal conductivities and improved thermal stability due to an oxide-defect-cluster design. Critical issues for designing advanced low conductivity coatings with improved coating durability are also discussed.

Zhu, Dong-Ming↗

Effect of Tungsten L-PBF Feedstock Modification on Performance in Bending

Additively manufactured tungsten is a candidate refractory material for high-temperature aerospace and nuclear fusion/fission applications. The printability of pure tungsten is challenged by cracking defects arising from the metal’s high ductile-to-brittle transition temperature and low solubility of interstitial impurities. Furthermore, the cast microstructure inherent to the laser powder bed fusion (L-PBF) process has limited strength compared to worked microstructures common in wrought tungsten. Aside from process-related techniques to mitigate defects and increase strength (e.g., heated build chambers, multi-laser systems, low oxygen environmental control, etc.), micro-alloying additions can positively influence tungsten printability. In this work, pure tungsten L-PBF feedstock was modified with 1 wt% additions of ceramic compound nano-powders. Wrought and printed bars were evaluated in four-point bending. Flexural strength and fractography were primary means of comparison to assess the effect of the feedstock modification on printed tungsten mechanical performance.

Tungsten-based alloys↗

Short-Term Elevated Temperature Mechanical Performance and Microstructure of A Niobium-Zirconium Alloy Produced via Laser Powder Bed Fusion In-Situ Alloying

Nb-1Zr is a readily fabricable, dispersion-strengthened niobium alloy with improved elevated temperature properties compared to commercially pure niobium. This low to moderate strength niobium alloy is desirable in thermal management systems for fission power and propulsion applications; however, pre-alloyed spherical feedstock for powder-based additive manufacturing processes is generally unavailable. Laser powder bed fusion (L-PBF) in-situ alloying of a Nb-1Zr chemistry was performed using a high-purity niobium feedstock coated with 1 wt% of zirconium-based ceramic compound nano-powders: ZrO 2 , ZrC, and ZrH 2 . The additively manufactured material was mechanically tested at elevated temperatures within a controlled environment in the as-built condition. For comparison, traditionally manufactured wrought feedstock was also tested within an identical environment. Examination of the materials’ microstructure and short-term elevated temperature mechanical response determined: in-situ alloying of spherical Nb powder feedstock with Zr-based ceramic nanoparticles can be successfully implemented; the ZrO 2 addition offered the greatest elevated temperature stability and strength but exhibited brittle behavior; the ZrC addition achieved a balance of room temperature ductility and elevated temperature strength; and the ZrH 2 -modified material had the lowest as-built interstitial content and showed high ductility with mechanical performance most similar to wrought Nb-1Zr.

Niobium Alloy↗

Laser peening for reducing hydrogen embrittlement

A laser peening process for the densification of metal surfaces and sub-layers and for changing surface chemical activities provides retardation of the up-take and penetration of atoms and molecules, particularly Hydrogen, which improves the lifetime of such laser peened metals. Penetration of hydrogen into metals initiates an embrittlement that leaves the material susceptible to cracking.

36 MATERIALS SCIENCE↗

Isotopic imaging via nuclear resonance fluorescence with laser-based Thomson radiation

The present invention utilizes novel laser-based, high-brightness, high-spatial-resolution, pencil-beam sources of spectrally pure hard x-ray and gamma-ray radiation to induce resonant scattering in specific nuclei, i.e., nuclear resonance fluorescence. By monitoring such fluorescence as a function of beam position, it is possible to image in either two dimensions or three dimensions, the position and concentration of individual isotopes in a specific material configuration. Such methods of the present invention material identification, spatial resolution of material location and ability to locate and identify materials shielded by other materials, such as, for example, behind a lead wall. The foundation of the present invention is the generation of quasimonochromatic high-energy x-ray (100's of keV) and gamma-ray (greater than about 1 MeV) radiation via the collision of intense laser pulses from relativistic electrons. Such a process as utilized herein, i.e., Thomson scattering or inverse-Compton scattering, produces beams having diameters from about 1 micron to about 100 microns of high-energy photons with a bandwidth of .DELTA.E/E of approximately 10E.sup.-3.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Measurement of buried undercut structures in microfluidic devices by laser fluorescent confocal microscopy

Measuring buried, undercut microstructures is a challenging task in metrology. These structures are usually characterized by measuring their cross sections after physically cutting the samples. This method is destructive and the obtained information is incomplete. The distortion due to cutting also affects the measurement accuracy. In this paper, we first apply the laser fluorescent confocal microscopy and intensity differentiation algorithm to obtain the complete three-dimensional profile of the buried, undercut structures in microfluidic devices, which are made by the soft lithography technique and bonded by the oxygen plasma method. The impact of material wettability and the refractive index (n) mismatch among the liquid, samples, cover layer, and objective on the measurement accuracy are experimentally investigated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Laser-Induced Self-Assembled Nanostructures on Electron-Transparent Substrates

Currently, one of the challenges in high-resolution transmission electron microscopy (TEM) studies of nanomaterials is to make contamination-free materials in a simple and time-efficient way. We demonstrate a method that combines nanosecond-pulsed laser dewetting of thin films with a film float-off technique to realize nanostructures (NSs) on electron-transparent substrates in a robust and rapid manner. NSs of metal (Ag) and bimetals (AgCo, AuCo) ranging from 20 to 150 nm are synthesized on thin carbon film deposited on mica substrates. The NS/carbon system is subsequently transferred onto TEM grids by a float-off process resulting from debonding of the carbon from mica due to their contrasting hydrophobic nature. Our process enables the fabrication of different NSs on flexible and electron-transparent substrates.

36 MATERIALS SCIENCE↗

Dissolution zone model of the oxide structure in additively manufactured dispersion-strengthened alloys

The structural evolution of oxides in dispersion-strengthened superalloys during laser-powder bed fusion is considered in detail. Alloy chemistry and process parameter effects on oxide structure are assessed through a parameter study on the model alloy Ni-20Cr, doped with varying concentrations of Y 2 O 3 and Al. Small angle neutron scattering measurements of the dispersoid size distribution show the dispersoid size increases with higher laser power, slower scan speed, and increasing Y 2 O 3 and Al content. Complementary electron microscopy measurements reveal reactions between Y 2 O 3 and Al, even in nanoscale dispersoids, and the presence of micron-scale oxide slag inclusions in select specimens. A scaling analysis of mass and momentum transport within the melt pool, presented here, establishes that diffusional structural evolution mechanisms dominate for nanoscale dispersoids, while fluid forces and advection become significant for larger slag inclusions. These findings are developed into a theory of dispersoid structural evolution, integrating quantitative models of diffusional processes – dispersoid dissolution, nucleation, growth, coarsening – with a reduced order model of time-temperature trajectories of fluid parcels within the melt pool. Calculations of the dispersoid size in single-pass melting reveal a zone in the center of the melt track in which the oxide feedstock fully dissolves. Within this zone the final Y 2 O 3 size is independent of feedstock size and determined by nucleation and growth kinetics. If the dissolution zones of adjacent melt tracks overlap sufficiently with each other to dissolve large oxides, formed during printing or present in the powder feedstock, then the dispersoid structure throughout the build volume is homogeneous and matches that from a single pass within the dissolution zone. Gaps between adjacent dissolution zones result in oxide accumulation into larger slag inclusions. Predictions of final dispersoid size and slag formation using this dissolution zone model match the present experimental data and explain process-structure linkages speculated in the open literature.

36 MATERIALS SCIENCE↗

Creation of a two-dimensional electron gas and conductivity switching of nanowires at the LaAlO{sub 3}/SrTiO{sub 3} interface grown by 90{sup o} off-axis sputtering

Two-dimensional electron gas (2DEG) formed at the interface between two oxide band-insulators LaAlO{sub 3} and SrTiO{sub 3} raises the possibility to develop oxide nanoelectronics. Here, we report the creation of a 2DEG at the LaAlO{sub 3}/SrTiO{sub 3} heterointerfaces grown by 90° off-axis sputtering which allows uniform films over a large area. The electrical transport properties of the LaAlO{sub 3}/SrTiO{sub 3} heterointerface are similar to those grown by pulsed laser deposition. We also demonstrate room-temperature conductive probe-based switching of quasi-one-dimensional structures. This work demonstrates that a scalable growth process can be used to create the two-dimensional electron gas system at oxide heterointerfaces.

36 MATERIALS SCIENCE↗

Lightweight Thrust Chamber Assemblies using Multi-Alloy Additive Manufacturing and Composite Overwrap

Additive Manufacturing (AM) has brought significant design and fabrication opportunities for complex components with internal features such as liquid rocket engine thrust chambers not previously possible. This technology allows for significant cost savings and schedule reductions in addition to new performance optimization through weight reduction and increased margins. Specific to regeneratively-cooled combustion chambers and nozzles for liquid rocket engines, additive manufacturing offers the ability to form the complex internal coolant channels and the closeout of the channels to contain the high pressure liquid propellants with a single operation. Much of additive manufacturing development has focused on monolithic alloys using Laser Powder Bed Fusion (L-PBF), which do not allow for complete optimization of the structure. The National Aeronautics and Space Administration (NASA) completed feasibility of an AM bimetallic L-PBF GRCop-84 copper-alloy combustion chamber with an AM electron beam freeform Inconel 625 structural jacket under the Low Cost Upper Stage Propulsion (LCUSP) Project. A follow-on project called Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) is under development to further expand large-scale multi-alloy thrust chambers while maturing composite overwrap technology for significant weight savings opportunities. The RAMPT project has three primary objectives: 1) Advancing blown powder Directed Energy Deposition (DED) to fabricate integral-channel large scale nozzles, 2) Develop composite overwrap technology to reduce weight and provide structural capability for thrust chamber assemblies, and 3) Develop bimetallic and multi-metallic additively manufactured radial and axial joints to optimize material performance. In addition to these primary manufacturing developments, analytical modeling efforts compliment the process development to simulate the AM processes to reduce build failures and distortions. The RAMPT project is also maturing the supply chain for various manufacturing processes described above in addition to L-PBF of GRCop-42. This paper will present an overview of the RAMPT project, the process development and hardware progress to date, material and hot-fire testing results, along with future developments.

Additive Manufacturing↗

Operando visualization of porous metal additive manufacturing with foaming agents through high-speed x-ray imaging

Porous metals find extensive applications in soundproofing, filtration, catalysis, and energy-absorbing structures, thanks to their unique internal pore structure and high specific strength. In recent years, there has been an increasing interest in fabricating porous metals using additive manufacturing (AM), leveraging its unique advantages, including improved design freedom, spatial material control, and cost-effective small-batch production. In this study, we conducted pioneering operando visualization of AM porous metal using a laser powder bed fusion (L-PBF) setup combined with a high-speed synchrotron x-ray imaging system. Single track printing experiments using Ti6Al4V (Ti64) combined with titanium hydride (TiH 2 ) and sodium carbonate (Na 2 CO 3 ) as foaming agents, with varying mixing ratios were performed under different processing conditions. Here. the results elucidate the dynamic development of porosity formation. The average pore size is significantly influenced by the particle size of foaming agents when pore coalescence is absent. For all foaming agent content tested in the current study, the number of pores is found to be more sensitive to changes in laser power than in laser scanning speed. Increasing linear energy density (increasing laser power or reducing laser scanning speed) promotes the foaming agent activation thereby porosity formation. However, high linear energy density skews pore distribution towards the surface despite forming deeper melt pools. In addition, the impact of additional factors including foaming agent's laser absorptivity and decomposition kinetics with respect to AM time scales should be carefully considered to avoid ineffective activation of foaming agents during the AM of porous metals.

36 MATERIALS SCIENCE↗