Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Unusual flat and extended morphology of intercalated Cu under MoS 2

We report a general method was developed to intercalate metals under layered materials through a controlled density of sputtered defects. The method has already been applied to study a range of metals intercalated under graphite, and different types of morphologies were realized. In the current work, we extend the method to the study of intercalation under MoS 2 , noting that work on this system is rather limited. We use Cu as the prototype metal for comparison with Cu intercalation under graphite. Although the growth conditions needed for intercalation under graphite and MoS 2 are similar, the type of intercalated phases is very different. Each Cu island that nucleates on top of MoS 2 during Cu deposition provides material that is transferred below MoS 2 through sputtered defects under the island base; this transfer results in a uniform intercalated Cu “carpet” morphology that extends over the mesoscale. On the contrary, Cu intercalation under graphite results in well separated, compact islands formed by monomer detachment from small Cu islands on top and transfer below through defects far from the islands. The structural techniques (scanning electron microscopy and atomic force microscopy) and spectroscopic techniques (x-ray photoelectron spectroscopy and energy-dispersive spectroscopy) are used for the characterization of the intercalated Cu layer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

SENSITIVITY EVALUATION OF THE DAILY THERMAL PREDICTIONS OF THE AGR-2 EXPERIMENT IN THE ADVANCED TEST REACTOR

A temperature sensitivity evaluation has been performed for the AGR-2 fuel experiment on an individual capsule. A series of cases were compared to a base case by varying different input parameters into the ABAQUS finite element thermal model. These input parameters were varied by ±10% to show the temperature sensitivity to each parameter. The most sensitive parameters are the outer control gap distance, heat rate in the fuel compacts, and neon gas fraction. Thermal conductivity of the fuel compacts and thermal conductivity of the graphite holder were in the middle of the list for sensitivity. The smallest effects were for the emissivities of the stainless steel and graphite, along with gamma heat rate in the non-fueled components. Sensitivity calculations were also performed varying with fast neutron fluence, showing a general temperature rise with an increase in fast neutron fluence. This is a result of the control gas gap becoming larger due to the graphite holder shrinkage with neutron damage. A smaller sensitivity is due to the thermal conductivity of the fuel compacts and graphite holder decreasing with fast neutron fluence.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TU-F-BRE-09: Towards the Establishment of Dosimetric References in Small Fields Using the New Concept of Dose-Area Product

Purpose: To establish dosimetric references of absorbed dose in water in radiation fields smaller than 2 cm used in radiotherapy thanks to a new methodology based on the use of dosimeters larger than the field size. Methods: A new graphite calorimeter was constructed with a large sensitive volume (diameter of the core: 30 mm). This primary dosimeter was fully characterized and compared to previous LNE-LNHB graphite calorimeters in a 60Co large field. A specially designed graphite parallel-plate ionization chamber with a 30 mm collecting electrode was also assembled and tested. Measurements were then conducted in two 6 MV small circular fields of 2 cm and 1 cm diameter respectively, using the new concept of dose-area product instead of punctual dose commonly used in radiotherapy. Results: The dose rate established in a large 60Co field with the new calorimeter is in agreement within 0.4% with previous calorimeters. The ionization chamber shows good characteristics except for a 0.06% drift per hour in water. The ratio of calorimetric against ionometric measurements in the 2 cm diameter field is 1.1% higher than the one in the 1 cm diameter field (with respectively 0.30% and 1.03% type A uncertainty for each field). Conclusion: Results presented here highlight the possibility of measuring dose-area products in small fields with a graphite calorimeter and a parallel-plate ionization chamber. Measurements in a 0.75 cm diameter field are already underway to confirm the trend observed in the 2 cm and 1 cm diameter fields. The last step to establish precise dosimetric references in small fields is to calculate correction factors thanks to Monte Carlo simulations.

07 ISOTOPE AND RADIATION SOURCES↗

Siloxane Deposition on the Ni-YSZ Solid Oxide Fuel Cell Anode Exposed to Bio-Syngas

Siloxane, a common contaminant present in biogas, is known for adverse effects on cogeneration prime movers. In this study, the siloxane deposition products and mechanism in the solid oxide fuel cell nickel-yttria stabilized zirconia (Ni-YSZ) anode are investigated analytically and experimentally. An SOFC with Ni-YSZ anode and pure Ni/YSZ pellets were exposed to a simulated biogas-reformate fuel with octamethylcyclotetrasiloxane (D4) contamination at 750 °C. The electrochemical characterization results show that the SOFCs performance degradation caused by D4 contamination is irreversible. Morphology and XRD results illustrate that silicon and carbon deposition can both be detected in the anode and pellets. Graphite, SiC and SiO2 are all possible products based on the results of XRD test. Here, according to the formation of graphite and SiC, the new mechanism suggests that carbon is also an essential factor in siloxane contamination of Ni-YSZ anodes besides silicon, which can be explained by the catalytic and electrochemical analysis.

25 ENERGY STORAGE↗

Cycling Performance and Structure Evolution of Co-Free Lithium- and Manganese-Rich Layered Oxides in Lithium-Ion Batteries

Lithium- and manganese-rich (LMR) layered oxides are high-capacity cathode materials that are being considered for electric vehicle (EV) lithium-ion batteries (LIBs). Here, we investigate the electrochemical cycling behavior of cells containing a cobalt-free LMR oxide, 0.3Li 2 MnO 3 ·0.7LiMn 0.5 Ni 0.5 O 2 , paired with either Li or graphite anodes. Two- and three-electrode cells are cycled under varying conditions to examine the effects of oxide activation, upper cutoff voltage, separator type, and electrolyte composition. Post-cycling characterization of harvested electrodes, with electrochemical, X-ray absorption spectroscopy, and solid-state 6 Li nuclear magnetic resonance spectroscopy techniques, are used to correlate cell performance changes with redox state evolution in the oxide and Li inventory shifts in the cell. Our results show that capacity fade and impedance rise primarily originate at the graphite anode and LMR cathode, respectively. Notably, while Ni undergoes reversible redox, Mn shows no evidence of bulk redox activity even in highly-aged electrodes: only relithiated LMR electrodes show some reduction of Mn. Graphite electrodes degrade due to particle isolation and SEI growth, exacerbated by Mn dissolution and deposition on graphite anodes. These findings highlight the coupled structural and electrochemical degradation mechanisms in LMR/graphite cells and underscore lithium inventory retention and electrode interfacial stability as critical factors for enhancing long-term performance.

Badami, Pavan P. [Argonne National Laboratory (ANL↗

Sulfone-Based Electrolytes for Next Generation Lithium Batteries

An electrolyte system based on a sulfone solvent will be presented, outlining a newly discovered synergy between solvent and salt that simultaneously addresses the interfacial requirements of coupling a graphitic anode with a high voltage spinel cathode (LNMO). At the anode, a LiF-rich interphase generated by early-onset reduction of the salt anion effectively suppresses solvent co-intercalation and subsequent graphite exfoliation, enabling unprecedented and highly reversible graphite cycling in a pure sulfone system. Under aggressively oxidative conditions, QC calculations predict that high salt concentration promotes formation of complexes/aggregates which slow the decomposition of the solvent and leads to polymerizable rather than gaseous byproducts--a fundamental improvement over conventional electrolytes. These predictions are corroborated by an in-depth analysis of these functional interphases, as well as stable, long term operation of high voltage (4.85V) LNMO-graphite full cells.

Schroeder, Marshall A.↗

Rheology Analysis of Thermosetting Resin Candidates for Use in Fuel Compacting

The AGR-1 and AGR-2 overcoating and compacting method utilized a wet mixing process where liquid resin (Hexion Durite SC-1008) was blended with natural and synthetic graphite to produce a graphite/resin matrix for overcoating. The matrix production method specified in the scale-up plan is a co-grinding jet mill process where powdered resin and graphite are fed at the same time into a jet mill. Because of the change in matrix production style, SC-1008 cannot be used in the jet milling process because it is a liquid. Also, attempts to dry out matrix made with SC-1008 for use in the overcoating process at B&W had mixed results. The SC-1008 resin became tacky when dried which caused the matrix to build up inside the overcoater. The scale- up jet milling/mixing and overcoating processes required that a suite of solid or powdered resins be identified. Suitable resins candidates were down selected to two resins, specifically Plenco 14838 and Hexion SD-1708. These resins are referred to as novolac or “two-stage” resins because they require the addition of a curing agent such as hexamethylenetetramine (Hexa) to promote an increased level of cross linking. The overcoating matrix is made of 3 components; natural graphite, synthetic graphite, and resin. The most influential component of the compacting process is the resin component and how it behaves with regards to time, temperature, and pressure. The selected scale-up resins are considered fast curing which means that the increase in molecular weight (curing) occurs over a relatively short period of time, ranging from a few seconds to several minutes depending on the temperature. To find the optimal compacting conditions it is useful to quantify this behavior. In this report, rheology is used to investigate viscosity as a function of time at specific temperatures for the previously mentioned resins.

36 MATERIALS SCIENCE↗

High Energy, Long Cycle Life Lithium-ion Batteries for PHEV Application

High-loading and high quality PSU Si anode has been optimized and fabricated. The electrochemical performance has been utilized. The PSU Si-graphite anode exhibits the mass loading of 5.8 mg/cm2, charge capacity of 850 mAh/ g and good cycling performance. This optimized electrode has been used for full-cell fabrication. The performance enhancement of Ni-rich materials can be achieved by a diversity of strategies. Higher Mn content and a small amount of Al doping can improve the electrochemical performance by suppressing interfacial side reactions with electrolytes, thus greatly benefiting the cyclability of the samples. Also, surface coatings of Li-rich materials and AlF 3 are able to improve the performance stability of Ni-rich cathodes. One kilogram of optimized concentration-gradient LiNi 0.76 Co 0.10 Mn 0.14 O 2 (CG) with careful control of composition, morphology and electrochemical performance was delivered to our collaborators. The sample achieved an initial specific capacity close to 190 mA h g -1 at C/10 rate and 180 mA h g -1 at C/3 rate as well as good cyclability in pouch full cells with a 4.4 V upper cut-off voltage at room temperature. Electrolyte additive with Si-N skeleton forms a less resistant SEI on the surface of silicon anode (from PSU) as evidenced by the evolution of the impedance at various lithiation/de-lithiation stages and the cycling data The prelithiation result demonstrates a solution processing method to achieve large area, uniform SLMP coating on well-made anode surface for the prelithiation of lithium-ion batteries. The prelithiation effect with this method is applied both in graphite half cells, graphite/NMC full cells, SiO half cells, SiO/NMC full cells, Si-Graphite half cells and Si-Graphite/NMC full cells with improvements in cycle performance and higher first cycle coulombic efficiency than their corresponding cells without SLMP prelithiation. As to the full cell fabrication and test, full pouch cells with high capacity of 2.2 Ah and 1.2 Ah have been fabricated and delivered. The cells show great uniformity and good cycling performance. The prelithiation method effectively compensate the loss in the first cycle. The cell with high energy density and long-cycle life has been achieved.

25 ENERGY STORAGE↗

Fission Product Inventory and Burnup Evaluation of the AGR-2 Irradiation by Gamma Spectrometry

Gamma spectrometry has been used to evaluate the burnup and fission product inventory of different components from the US Advanced Gas Reactor Fuel Development and Qualification Program's second TRISO-coated particle fuel irradiation test (AGR-2). TRISO fuel in this irradiation included both uranium carbide / uranium oxide (UCO) kernels and uranium oxide (UO 2 ) kernels. Four of the 6 capsules contained fuel from the US Advanced Gas Reactor program, and only those capsules will be discussed in this work. The inventories of gamma-emitting fission products from the fuel compacts, graphite compact holders, graphite spacers and test capsule shell were evaluated. These data were used to measure the fractional release of fission products such as Cs-137, Cs-134, Eu-154, Ce-144, and Ag-110m from the compacts. The fraction of Ag-110m retained in the compacts ranged from 1.8% to full retention. Additionally, the activities of the radioactive cesium isotopes (Cs-134 and Cs-137) have been used to evaluate the burnup of all US TRISO fuel compacts in the irradiation. The experimental burnup evaluations compare favorably with burnups predicted from physics simulations. Predicted burnups for UCO compacts range from 7.26 to 13.15 % fission per initial metal atom (FIMA) and 9.01 to 10.69 % FIMA for UO 2 compacts. Measured burnup ranged from 7.3 to 13.1 % FIMA for UCO compacts and 8.5 to 10.6 % FIMA for UO 2 compacts. Results from gamma emission computed tomography performed on compacts and graphite holders that reveal the distribution of different fission products in a component will also be discussed. Gamma tomography of graphite holders was also used to locate the position of TRISO fuel particles suspected of having silicon carbide layer failures that lead to in-pile cesium release.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An Integrated Supercritical System for Efficient Produced Water Treatment and Power Generation

The main goal of this project was to evaluate the feasibility of an integrated supercritical (SC) water desalination and power generation system for treatment of produced waters from CO 2 sequestration, oil production, and coal-bed methane recovery. This system may offer a transformative approach to generating power from coal or natural gas (NG) and purifying saline water or produced water with high total dissolved solids (TDS) in a zero-liquid discharge plant. The closed-loop steam cycle of conventional power plants was replaced with an open-loop steam cycle that heated the pretreated produced water above the SC point of water (374 °C and 221 bar) to precipitate and separate the salts dissolved in the water. After separation of the precipitated salt, the SC steam required further treatment to reduce the salt content from ~100 mg/L (ppm) to <1 ppm to make it suitable for use in turbines for power generation. A SC membrane distillation unit was used to polish the SC steam, which could be sent through a series of turbines for power generation, and the steam exiting the low-pressure turbine could be condensed by cooling water to produce pure water. Project tasks included a process simulation and a techno-economic evaluation of the integrated system; design and assembly of SC salt precipitation and membrane distillation systems; development and characterization of advanced carbon membranes for SC membrane distillation; and pretreatment, desalination, and purification of different produced water samples with salt concentrations of 30,000–200,000 ppm to a high-purity (<1 ppm) level. Process simulations were performed for 550 MW SC coal-fired or NG baseline cases and various scenarios for the proposed integrated SC system using produced water as the water source and coal or NG as the fuel source. Simulation results indicated that the net plant efficiency loss of the proposed SC cogeneration process would be in the range of <1% to ~4%, in which NG and lower TDS produced water cases would have higher efficiencies. The proposed process for coal-fired cases could provide all water needs for the power generation process and generate additional pure water for beneficial use. A techno-economic analysis was performed to estimate the cost of produced water treatment (dollars /kgal of treated water) by conventional treatment processes compared with the proposed cogeneration process. The cost estimation for the proposed cogeneration system included the cost of pretreatment, the cost of power loss to integrate the water desalination process into the power generation system, and the cost of plant modification or retrofitting. The cost of produced water treatment was calculated by assuming three different scenarios in which converting a baseline power plant to the proposed cogeneration plant would increase the cost of the boiler and feed water system by 10%, 50%, and 100%. Results indicated that the cost of produced water treatment, even with a 100% cost increase, was in the range of $8.6–11.6 dollars per kgal, which is about half of the treatment cost by conventional methods. The cost of produced water treatment by the proposed cogeneration system could be further reduced or a considerable income could be generated if the values of saltwater and freshwater products are considered. Overall, the techno-economic analysis results indicated that the proposed integrated SC system could potentially treat produced water at a cost significantly lower than the cost of produced water treatment by conventional technologies. To evaluate the feasibility of the proposed treatment system at a laboratory scale, a SC salt precipitation and membrane distillation system was designed and fabricated to treat a simulated brine or pretreated produced water by precipitating salts and further polishing the SC steam containing ~100 ppm salts to a high-purity steam. Through baseline tests with NaCl solutions, with concentrations ranging from 30,000 to 200,000 ppm, it was demonstrated that concentrated feed solutions could be treated by precipitating salt at SC conditions to a TDS level of 130 ppm. Produced water samples were collected from a potential CO 2 sequestration site, a coal-bed methane site, and an oilfield in Illinois. Representative samples were characterized for various water quality parameters, including pH; turbidity; conductivity; and concentrations of selected anions, cations, alkalinity, dissolved organic carbon, total suspended solids, TDS, and total petroleum hydrocarbons. The produced water samples were first treated by conventional pretreatment methods to remove residual oil, dissolved organic matter, and scale-forming species. Pretreatment methods included coagulation, sedimentation, filtration, activated carbon adsorption, and ion-exchange adsorption. Pretreated produced waters were treated at SC conditions in which salts were precipitated. Analysis of treated samples revealed that the concentration of Na (the main cation) in produced waters was reduced dramatically from 14,000–47,400 ppm in the feed to 21–80 ppm in treated waters. Concentrations of other main cations (Ca, Mg, Sr, K) also decreased significantly from initial values of ~1,000–22,000 ppm to ~1 ppm or less. However, a significant increase in the concentrations of Fe, Ni, Cu, and Co was observed, mainly caused by leaching of these elements from the system (vessels, filters, tubing), which is manufactured from alloys containing Fe, Ni, Cu, and Co. To polish the SC steam containing a salt content of ~100 ppm to a high-purity level of <1 ppm, a SC membrane distillation treatment using carbon membranes was employed. Different types of self-standing or supported carbon membranes were developed from graphite, graphene, carbon nanotubes, carbon nanofibers, and pyrolytic carbon. Screening tests revealed that only a limited number of developed carbon membranes were suitable for the purification of steam at SC conditions. Membranes that were either fragile and lacked mechanical strength or had large pores and showed limited salt rejection (<20%) were found to be unsuitable for the purification of SC steam. Promising carbon membranes that were successfully tested for purifying SC steam included two graphite membranes (i.e., AF-5, a porous graphite material, and FGS, a flexible graphite sheet) and a carbon nanotube membrane grown on a Hastelloy substrate and then further modified using a proprietary method (i.e., membrane C). The AF-5 membrane exhibited a stable water flux of ~50 kg/m 2 ∙h and ~40% salt rejection. The FGS membrane had a high salt rejection of 95%–98% but a lower water flux of ~15 kg/m 2 ∙h. Membrane C showed an extremely high flux of 200-800 kg/m 2 ∙h, which is one order of magnitude higher than the water flux of conventional membranes. Membrane C also exhibited 87%–93% salt rejection. Overall, a two-stage or multistage polishing treatment by these membranes could lower the salt content of the SC steam from initial values of ~100–200 ppm to the steam quality of <1 ppm or to parts per billion levels required for the power cycle.

20 FOSSIL-FUELED POWER PLANTS↗

ZEUS Activation Foils Report for Experiments 1-5

The ZEUS experiments were conducted using the COMET vertical assembly machine at the Los Alamos Critical Experiments Facility (LACEF) at the Los Alamos National Laboratory (LANL). The experiments were designed to check the adequacy of cross sections in the intermediate-energy range. For the first four experiments, 12 kg highly enriched uranium (HEU) layers were sandwiched between different numbers of graphite plates in a vertical stack. In the first four experiments, a unit cell consisted of n graphite plates, an HEU layer, and then another n graphite plates. The unit cells were stacked until criticality was obtained. Experiments 1, 2, 3, and 4 contained decreasing amounts of graphite, where the unit cells value n was 4, 3, 2 and 1 respectively. In experiment 5 the HEU plates were in direct contact with each other to evaluate cross sections in the fast-energy range. A detailed description of experiments 1-4 is provided in reference, and of experiment 5, in reference. In order to investigate the cross sections in more detail, some ZEUS runs were made with activation foils inside the assemblies. Ratios of the activations of various foils are a standard method of measuring the gross neutron spectrum shape. A more detailed spectrum can be determined by simultaneously unfolding the response of several foils. This report describes the unfolding of the ZEUS activation foils data. The focus in this analysis is on the fast-energy range, especially at > 5 MeV.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-3/4 Experiment Preliminary Mass Balance

AGR-3/4 was an experiment primarily aimed at studying fission product transport in graphite and graphitic materials. To accomplish this, 80 designed-to-fail (DTF) particles coated only with a thin pyrocarbon layer were incorporated among the roughly 7500 tristructural isotropic-coated driver fuel particles in each capsule. It was anticipated that intact DTF particles would behave like TRISO particles with SiC layer failures (releasing cesium and other metallic fission products to some extent, but retaining fission gases), and failed DTF particles would behave like TRISO particles with failed TRISO coatings (releasing both cesium and other metallic fission products and fission gases). The DTF particles provided a known source of fission products to migrate out into the fuel compact matrix and out into the surrounding concentric rings of graphite and graphitic matrix material for study. Post-irradiation examinations have focused on measuring the total releases of fission products from the fuel compacts (mass balance) and the spatial distribution of fission products in the rings. The total mass balance is an important parameter for comparison to fission product transport simulations of the AGR-3/4 experiment, and the spatial distribution within carbon rings is being used to derive fission product diffusion coefficients. To determine the fission product mass balance, each of the 12 irradiation capsules was disassembled, and their component parts analyzed via gamma counting and destructive leach or burn-leach methods. In “standard” capsules (Capsules 1, 3-5, 7-8, 10, and 12), inner rings, outer rings, sink rings, spacers, foils, felts, and through tubes were all analyzed for gamma-emitting fission products. Beta-emitting Sr-90 was measured as well, but because of the analysis program on the inner and outer rings, the Sr-90 inventory of the inner and outer rings is not yet available. “Fuel body” Capsules 2, 6, 9, and 11 were retained intact for future heating tests; thus, the inner and outer rings from these capsules were not measured. The most commonly detected radionuclide fission products were Ag-110m, Cs-134, Cs-137, Eu-154, Eu-155, and Sr-90. Sb-125 was also frequently detected in the sink rings and spacers; however, the zircaloy spacers used in Capsules 1 through 6 contained natural antimony that transmuted to Sb-125 and made it impossible to separate Sb-125 released from the fuel from that generated in the spacers. Summing the fission product inventory measured on each capsule component made it clear that the presence of 80 DTF particles in each capsule resulted in noticeably higher releases of cesium, europium, and strontium from AGR-3/4 fuel when compared to AGR-1 fuel which did not have DTF particles. Greater than 30 particles worth of Cs-134 was measured outside of the fuel compacts in Capsules 3-5, 7, 8, and 10. In Capsule 11 (an intact fuel body for which the inner and outer rings were not measured), 26 particle equivalents of Cs-134 was measured outside of the outer ring. Based on experience from AGR 1, it is very unlikely that any driver particles failed during the irradiation; therefore, this cesium is assumed to be overwhelmingly dominated by release from DTF particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Compilation for AGC-2 Matrix-only Compact Lot A3-H08

This document is a compilation of fabrication and characterization data for the compact lot A3-H08, which was produced for possible insertion into the second ATR Graphite Creep irradiation test capsule (AGC-2). The compacts were produced by Oak Ridge National Laboratory (ORNL) for the Advanced Gas Reactor Fuel Development and Qualification (AGR) program. This compact lot was fabricated using a graphite/resin blend formulated by INL as a candidate matrix precursor for scale-up of overcoating and compacting processes. The matrix precursor powder for compact lot A3-H08 was a jet milled blend of 64 wt% natural graphite (Asbury 3482), 16 wt% synthetic graphite (Graftech GTI-D), and 20 wt% high purity novolac resin (Hexion D_SD-1708 with 7.5% hexamethylenetetramine added). The “Matrix Compacts for AGC-2 Irradiation” Specification (INL SPC-1285, Rev. 1) provides the requirements necessary for acceptance of the compacts. Sections 2.03 and 2.04 of SPC-1285 provide the property requirements for the heat-treated compacts. There are requirements on the length, diameter, and matrix density. Section 2.02.01.01 further requests impurity analysis on representative samples from the final compact lot, but there are no specified acceptance criteria. The impurity information will be evaluated by INL as part of a final decision on whether to insert the compacts into the AGC-2 experiment. The procedures for characterizing and qualifying the compacts are outlined in ORNL product inspection plan AGR-CHAR-PIP-16. The measurement of compact length, diameter, and matrix density was performed according to data acquisition method AGR-CHAR-DAM-39. The data report forms generated by this procedure document the product acceptance for the property requirements listed in sections 2.03 and 2.04 of SPC-1285. All compacts selected for irradiation conformed to the specified requirements for length, diameter, and density. In addition to the characterization data, this report also contains other records relevant to the product acceptance. A history of the material flow and sample naming is included and the compacting process is summarized. In addition to results of the impurity analysis on representative samples from the final compact lot, impurity analysis results are also provided for samples of the graphite, resin, and the graphite/resin blend. A Certificate of Conformance to SPC-1285, Rev. 1 is attached in Appendix B.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Destructive PIE and Safety Testing of Six AGR-2 UO 2 Capsule 3 Compacts

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program’s second irradiation experiment (AGR-2) was irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) from June 2010 to October 2013 (Collin 2014). The fuel compacts in this experiment held either tristructural isotropic (TRISO)-coated spherical kernels of uranium oxide (UO2) or TRISO-coated kernels containing both uranium carbide and uranium oxide phases (UCO). There were six separately monitored and controlled capsules in the AGR-2 test train. Capsule 3 held twelve compacts containing UO2-TRISO particles fabricated by BWX Technologies Nuclear Operations Group. The AGR-2 TRISO particles were fabricated in a pilot-scale fluidized-bed chemical vapor deposition (FB-CVD) furnace with a coating chamber inner diameter of 150 mm (Phillips, Barnes, and Hunn 2010), which was a change from the first irradiation experiment (AGR-1) particles that had been coated in a lab-scale FB-CVD coating system with a chamber inner diameter of 50 mm (Lowden 2006). The TRISO particles were overcoated with resinated graphite flake at Oak Ridge National Laboratory (ORNL), and the overcoated particles were pressed into one-inch-long, half-inch-diameter cylinders (Hunn, Montgomery, and Pappano 2010). Each cylindrical compact held an average of 1,543 TRISO particles with 9.6% enriched UO2 kernels that had a nominal diameter of 500 μm (Hunn, Savage, and Silva 2012). Capsule 3 compacts were irradiated to average calculated burnups of 9.01–10.69% fissions per initial metal atom (FIMA), and the average calculated fluences of fast neutrons with energies E n > 0.18 MeV were 3.05–3.53×10 25 n/m 2 (Sterbentz 2014). The calculated time-average, volume-average Capsule 3 compact temperatures were 996–1,062°C. However, Capsule 3 compact temperatures varied several hundred degrees across each compact, and the timeaverage minimum (TA min ) and time-average maximum (TA max ) temperatures were between 889–999°C and 1,072–1,105°C, respectively (Hawkes 2014). After irradiation, the AGR-2 test train was transferred from ATR to the INL Materials and Fuels Complex for inspection and disassembly (Ploger, Demkowicz, and Harp 2015). The initial inspection included dimensional metrology of the compacts and graphite fuel holders. Like all the AGR-2 compacts, the compacts in Capsule 3 shrank slightly during irradiation, as expected, with an average length reduction of 1.07–1.24% and an average diameter reduction of 0.13–0.41%. Post-irradiation examination (PIE) of the capsule components was completed to measure select fission products ( 90 Sr, 110m Ag, 134 Cs, 137 Cs, 144 Ce, and 154 Eu) outside the compacts (Stempien and Demkowicz 2020). This involved gamma counting of the graphite and graphoil spacers at the top and bottom of each capsule, acid leaching for radiochemical analysis of fission products on the metallic capsule components, and burn-leach analysis of the graphite holders. The total amount of 110mAg measured on the Capsule 3 components was 13% of the calculated capsule inventory. This was significantly lower than the amount of 110m Ag measured on the three UCO capsule components, which ranged from 32–70%. The lower 110m Ag release in Capsule 3 was likely due to lower peak temperatures compared with the UCO fuel capsules (Hawkes 2014). Measured inventories of the other select fission products were also lower in Capsule 3.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Plutonium Production Reactor Progression Problems: Magnox Neutronics Benchmarks

The goal of this document is to provide a set of comprehensive benchmarking neutronics problems for gas-cooled, graphite-moderated reactors. The problems are designed to be representative problems that increase in complexity to test performance of various codes. For the simulation of the benchmarking problems, the Shift Monte Carlo code and MPACT deterministic code are chosen because of their state-of-the-art capabilities, which are optimized for various reactor designs. Because these codes have been developed primarily for light water reactor applications, their application to graphite-moderated, gas-cooled reactors has not been extensively explored. This report attempts to evaluate benchmarks for a Magnox-style reactor, one that is graphite-moderated and gas-cooled. Parameters that are calculated and presented in this benchmark include the eigenvalue, peaking factors, and isotope concentrations. Results show good agreement between Shift and MPACT, and demonstrate the capability of MPACT to model graphite-moderated systems well.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Gamma Spectrometry Examination of the AGR-3/4 Irradiation

The results from gamma spectrometry examination of the different components from the combined third and fourth U.S. Advanced Gas Reactor (AGR) TRISO-coated particle fuel irradiation tests (AGR-3/4) have been analyzed. This experiment was designed to provide information about in-pile fission product migration. In each of the 12 capsules, a single stack of four compacts with designed-to-fail (DTF) particles surrounded by inner and outer graphite and/or graphitic matrix rings and a graphite sink ring were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). Gamma spectrometry has been used to evaluate the gamma-emitting fission product inventory of compacts from the irradiation and evaluate the burnup of these compacts based on the activity of the radioactive cesium isotopes (i.e., Cs-134 and Cs-137) in the compacts. Burnup from gamma spectrometry compares well with predicted burnup from simulations. The inner and outer rings were also examined by gamma spectrometry to evaluate the total fission product inventory of the rings, and gamma emission computed tomography (GECT) was used to investigate the spatial distribution of gamma-emitting fission products within the rings. This report focuses on results obtained via the Precision Gamma Scanner (PGS) for the compacts and inner and outer rings. These non-destructive gamma measurements are currently being compared to recent destructive measurements of spatial fission product distributions in the rings and to predictions made via mathematical modeling. A separate report discusses the entire AGR-3/4 fission product mass balance for all irradiation capsule components including the inner and outer rings, graphite sink rings, capsule spacers, capsule foils, through tubes, and felts. This report is similar to the conference proceedings: Harp, J.M., Demkowicz, P.A., and Stempien, J.D., “Initial gamma spectrometry examination of the AGR-3/4 irradiation,” International Topical Meeting High Temperature Reactor Technology (HTR 2016), Las Vegas, NV, USA, November 2016, Paper HTR2016-18593, but it has been updated to reflect all the data that has been collected on AGR-3/4 using PGS. The Appendices contain extensive data from the collected gamma spectra.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Recent Testing of ENDF/B-VIII.0 at ORNL [Slides]

This presentation provides an overview of comparisons of ENDF/B-VII.1 and ENDF/B-VIII.0 and uses VALID suite to test >600 cases with ENDF/B-VII.1 and ENDF/B-VIII.0 in KENO V.a/KENO-VI, although a limited number of cases have been tested with TSUNAMI. It provides a results summary of KENO V.a/KENO-VI with a pooled results summary. The presentation also discusses changes for LCT experiments, MCT experiments, MST experiments, and PST experiments. A few words about graphite are also provided and the presentation states that graphite performance investigated across ENDF/B-VII.0, ENDF/B-VII.1, and ENDF/B-VIII.0 for MSR and HTGR models. A brief summary of the results is presented to make sure the Validation Committee is aware of the work. Also presented is an Eigenvalue comparison with a graphite moderated system, and comparison between an HTR-10 pebble model ENDF/B-VII.1 vs. ENDF/B-VIII.0, which provides different graphite data. In conclusion, ORNL has recently completed a comparison of ENDF/B-VIII.0 and ENDF/B-VII.1 using the VALID library. Work is also being performed for advanced reactor applications. Other efforts on-going and they are also trying to investigate more intermediate spectrum cases.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

HTV Post Irradiation Examination (PIE) Results and Analysis

This report is responsive to 2017 Idaho National Laboratory (INL) Memorandum Purchase Order No. 00181805, statement of work 13687 “HTR Graphite R&D – FY ORNL 2017 MPO”, Deliverable 12A “issue final report on the HTV PIE to INL”, due June 15 th 2017.The HTV (High Temperature Vessel) was a HFIR (High Flux Isotope Reactor) high temperature target rod capsule in support of the DOE’s (Department of Energy) High Temperature Reactor (HTR) program. The HTV capsule contained eight sub-capsules, each with nine graphite specimens. The sub-capsules were designed to operate at ~900°C, ~1200°C or ~1600°C. The actual irradiation temperature was established by interrogating SiC and graphite TMs during PIE (post-irradiation examination. The capsule dose ranged from 1.49 dpa to 3.34 dpa, and varied with specimen position within the capsule the maximum dose occurring at the reactor mid-plane and the minimum dose occurring at the core periphery. The irradiated graphite specimens were examined during PIE to establish their high temperature dimensional and elastic (Young’s) modulus changes. The PIE results are reported and analyzed here. The dimensional and modulus changes were shown to have a strong thermal dependence. The dimensional changes were small, being of the order of a few percent or less, ranging from a maximum shrinkage of -3.1% (PCEA WG, T irr =1500°C at 3.3 dpa) to +0.131% (2114 AG, T irr = 869 at 3.2 dpa). The specimen volume shrinkages varied from –0.81 (2114, T irr = 840 at 3.1 dpa) to -9.15% (PCEA, T irr =1500°C at 3.3 dpa). The volume changes were larger at higher Irradiation temperatures. Of the six grades examined, only 2114 moved into the net positive dimensional swelling situation. Significantly, the volume change for 2114 remained negative at the doses and temperature tested here. Dimensional and volume changes were explained in terms of the temperature dependence of the crystal growth rate, the anisotropy of the crystal growth (crystallographic c-axis growth and crystallographic a-direction shrinkage) and the thermal closure of aligned micro-porosity. The modulus changes were much larger, being of the order of a few tens of percent. A trend of lesser fractional increases of Young’s Modulus with an increasing T irr was noted. The minimum increase in Young’s Modulus was 20% (H-451 WG, T irr =1500°C at 3.3 dpa) and the maximum 71% (IG-110, T irr = 840(actual) at 3.3 dpa). The rise in Young’s modulus is attributed to dislocation pinning by lattice defects produced by neutron irradiation and the temperature dependency is related to the irradiation temperature influence on the number of defect available to pin dislocations.

36 MATERIALS SCIENCE↗