Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLUORIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Facile Separation of Sr-90, Fe-55, Nb-94, Ni-59,63 with Large Amount of Ca by Controlled pH Precipitation - 17190

it is important to manage low-and intermediate-level radioactive wastes from nuclear power plants due to a permanent disposal. According to the Nuclear Safety and Security Commission (NSSC), among all the regulatory radionuclides, a few radionuclides from the fission products and corrosion products such as Sr-90, Fe-55, Nb-94, Ni-59,63 which emit low-energy x-ray and beta radiation. Thus, it is necessary to separate beta-emitting nuclides individually. For that reason, KAERI has established analytical procedures which can separate Sr-90, Fe-55, Nb-94, Ni-59,63 from radioactive waste samples. However, when radioactive wastes contain large amount of Ca (above 300 mg), it is not easy to recover the target radionuclides because high concentration of Ca has a strong influence on the effective analyses. In order to combat this problem, there was an attempt to make the precipitate as CaF{sub 2} by using hydrofluoric acid. However, this way had a limitation; Fe-55, Nb-94 were precipitated as fluoride compounds as well as Ca. In this study, we have focused on developing a separation procedure stage by stage in the radioactive wastes with Sr-90, Fe-55, Nb-94, Ni-59,63 and large amount of Ca (1500 mg). The detailed steps are described below; (1) Separation of Fe-55, Nb-94, Ni-59,63 as metal hydroxide precipitates: low solubility product constant (Ksp) between pH 6 and pH 10. (2) Selective elimination of Ca-oxalate complex under strong acidic conditions. Consequently, all the metal sources were sequentially separated and quantitatively recovered by inductively coupled plasma atomic emission spectrometric (ICP-AES) analysis, the recovery is as follows; Sr-90 (3 mg): 89.47±5.48%, Fe-55 (20 mg): 99.80±3.19%, Nb-94 (20 mg): 97.45±2.42%, Ni-59,63 (2 mg): 83.59±15.31%, Ca (1500 mg): 85.32±6.38%, respectively. This methodology will help us separation of radioactive wastes efficiently if apply properly. (authors)

07 ISOTOPE AND RADIATION SOURCES↗

Demonstrating compliance with moderator content limits in uranium dioxide powder upon leaving a furnace environment

A challenge was posed to the criticality safety consultant to consider whether instrumentation identified by Plant Management in an existing facility could be claimed as appropriate safety measures to ensure compliance with moderator content limits in uranium dioxide (UO{sub 2}) powder. During processing of low enriched UO{sub 2}, trays of powder are heated in a steam and hydrogen environment in order to reduce fluoride levels. Whilst in the furnace environment criticality safety is ensured by the geometry of the furnace trays used to convey the powder; however, upon leaving the furnace the UO{sub 2} is bulked to a 210 litre drum subject to limited moderation control. Under fault conditions there is a potential that the powder may become wetted due to an imbalance in furnace gas flows resulting in steam condensing in the cooling section of the furnace. Therefore, the safety case methodology followed suggests that two independent and diverse safety measures are provided to terminate the progression of the fault(s) to criticality. The existing criticality safety case credits an infra-red moisture meter as one of two safety measures; however, the calibration procedure required to ensure this device remains suitable is a considerable challenge from a plant operability perspective. As an initial review failed to identify any suitable like-for-like replacement, the National Nuclear Laboratory (NNL) Nuclear Safety Section were requested by the customer to consider the existing criticality safety case and investigate whether any existing instrumentation could be used as an alternative method of detecting conditions in which excess moisture could be present within the furnace trays. A number of solutions were proposed and the benefits and challenges around each are discussed in this paper, concluding with the approach adopted by the project. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Test Bed: Treatability of Hanford Tank Waste - 18501

In an effort to advance the Low Activity Waste Pretreatment System technology readiness level at the Hanford Site, the effectiveness of a critical technology element, sRF ion-exchange resin, was demonstrated in the selective removal of Cs-137 from 11.5 L of composited Hanford supernate tank waste. Prior to ion-exchange, solids filtration was performed on the tank waste composite. Between the time of filtrate collection and filtrate processing on the ion-exchange columns, additional solids had formed. These secondary solids resulted from the combination of supernates high in fluoride content with supernates high in phosphate content and the relatively short blend time. Samples were collected before, during and after the ion-exchange process for characterization of a full suite of constituents (inorganic, organic, and radionuclides) to aid in the classification of the cesium-removed waste for shipping, receiving, treatment, and disposal determinations. Following chemical analysis, the remaining 10.8 L (2.9 gal) of cesium-depleted waste was shipped to an off-site vendor for grout-encapsulation and eventual disposal at the Waste Control Specialists Federal Waste Disposal Facility in Andrews, Texas as low-level waste. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Optimizing Short-Term Operation of a FIRES-like Industrial Heat Supply Thermal Energy Storage System

The Firebrick Resistance-heated Energy-storage System (FIRES) is under development at MIT for two applications: (1) integration with the Nuclear Air-Brayton Combined Cycle (NACC), a high-performance power conversion system (PCS) that may be used with high- temperature advanced reactors; and (2) industrial heat supply. This paper describes some key features of FIRES and equivalent systems configured for industrial heat supply and presents an assessment of the revenue achievable by a system operating under the conditions expected for early demonstration FIRES installations. The greatest technical challenge of the 21. century is likely to be the effort to minimize the damage caused by global climate change. This effort will require massive reductions in greenhouse gas (GHG) emissions throughout our economy and a transition to an electric power system driven entirely by very-low-carbon generators. Many investigators agree that this will require a substantial increase in electricity generation and in the use of nuclear power, and there is growing awareness that this will also require new technologies and systems for managing and storing energy and matching intermittent supply of renewable resources with electricity demand. Thermal energy storage systems (TESS) will, in some applications, be much more cost effective than the more popular and widely discussed battery electric storage systems and may provide unique capabilities. The Firebrick Resistance-heated Energy-storage System (FIRES) is under development at MIT for two applications: (1) integration with the Nuclear Air-Brayton Combined Cycle (NACC), a high-performance power conversion system (PCS) that may be used with high-temperature advanced reactors like the Fluoride-salt-cooled High-temperature Reactor (FHR), molten salt reactor (MSR) and sodium-cooled fast reactors (SFR); and (2) industrial heat supply. FIRES installations include a stack of refractory firebrick with imbedded electric heaters and airflow channels, a compressor or air blower, and a duct system to connect the firebrick with the heat demand (turbine or industrial customer). Analysis of the FIRES design space has shown that the concept is suitable for a wide range of peak operating temperatures (from about 200 deg.C up to at least 1800 deg. C) and pressures (from ambient to at least 20 atmospheres) and offers very high energy density (up to 1 MWh per cubic meter of firebrick for high temperature systems) at very low cost (as low as $5/kWh). These results favor early demonstration of FIRES. If the cost target of $5/kWh for FIRES systems were achieved, even the lowest expected operating income calculated here could cover the capital cost of a 10 MWh system in a single year. If the FIRES system were assumed to operate for at least 10 years, this level of operating income could readily recover a capital investment up to $50/kWh, which is simultaneously much cheaper than the costs expected for near-future battery systems (in excess of $200/kWh) and much more expensive than the small, low temperature firebrick systems already available for domestic heating. This provides a large margin for unexpected development costs and other uncertainties. FIRES would set a minimum price of electricity near that of natural gas-improving nuclear, wind, and solar economics while reducing greenhouse gas emissions from the industrial sector. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Molten Salt Reactor Experiment (MSRE) Lay-Up - 19187

UCOR, an AECOM-led partnership with Jacobs, manages the cleanup of the 2,200-acre East Tennessee Technology Park for its client, the U.S. Department of Energy (DOE), in Oak Ridge, Tennessee. The site was contaminated with radioactive, hazardous and industrial wastes generated by more than 40 years of national defense and energy missions. 2019 is the 50. anniversary of the shutdown of the Molten Salt Reactor Experiment (MSRE). MSRE ran a brief four years in the 1960's but earned an enduring legacy as an innovative reactor technology concept which has enjoyed a renewal of global interest in the past several years. In 2018, it was given elevated status among advanced reactor programs within DoE's Nuclear Energy office. The MSRE was a graphite-moderated, liquid fueled reactor that operated from June 1965 through December 1969. Although it was shut down nearly 50 years ago, certain systems within the reactor have continued to operate to maintain the facility in a safe and stable condition until it can be demolished as part of the comprehensive cleanup of the Oak Ridge Reservation. These systems are composed of a complex network of pipes, valves, gauges and associated equipment that control air filtration and pressure buildup resulting from fluorine gas generated through radiolysis of the fluoride salt which once fueled the reactor. In 2016, an MSRE Engineering Evaluation Team was chartered to assess current facility conditions and develop recommendations to maintain the facility in a safe state until deactivation and demolition commences. Plans are now underway to 'lay up' the MSRE facility until deactivation and demolition can occur. The proposed MSRE Facility Layup will minimize maintenance costs, reduce personnel risk of injury and exposure, provide reliable electric service to the facility and require zero personnel occupancy at MSRE. In the proposed layup approach a new source of electrical power to required loads will be routed through the facility, and new gas processing and ventilation systems will be installed that will be optimized for safe processing of the constituent hazardous gasses that exist in the legacy vessels at MSRE. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Trace Chemical Detection Using Intercalated MXenes as a Signal Enhancing Substrate in Optical Probes

MXenes are 2D materials composed of layered transition metal nitrides or carbides. These materials are synthesized by HF exfoliation from MAX phases (Ti{sub 3}AlC{sub 2}). The 2D nanomaterial was synthesized by the removal of the 'A' element, resulting in a Mxene product (Ti{sub 3}C{sub 2}). MXenes have the general formula M{sub n+1}X{sub n}T{sub x}, where M is an early transition metal, X is Carbon and/or Nitrogen, and T accounts for surface terminated functional groups such as Fluoride, hydroxyl, and oxygen. These materials have very unique properties, similar to graphene, that allows them to be applied in a variety of trace detection techniques including surface-enhanced Raman spectroscopy (SERS). MXenes have also been demonstrated to selectively uptake uranyl ion, UO{sub 2}{sup 2+}. If this property can be combined with SERS or fluorescence detection, it may be possible to use MXenes as the basis for an alternative method to kinetic phosphorescence analysis (KPA) for trace uranyl measurements. Objectives: To confirm that MXene Nano materials are suitable substrates for SERS and sensor development by enhancing Raman signaling. To determine if certain MXene preparation methods yield materials that are more suitable for trace sensing methods. To determine uranyl uptake properties of these MXene materials and test them for analytical signals. Sample Preparation: Preparation of Ti{sub 3}C{sub 2}MXene (at FSU). MXenes were prepared by etching Al from Ti{sub 3}AlC{sub 2} (MAX phase)material. Two etching techniques yield different MXene products: LiF/HCl: Milder reaction, larger MXene flakes. HF: Harsher reaction, smaller flakes, larger layer separation. Products washed to remove etchant, vacuum filtered, and dried. Dried MXene flakes are air-stable. Film preparation for sensor testing (at SRNL): Suspend powder in diH{sub 2}O, purge with Ar, sonicate for 30 min. Centrifuge and collect supernate with suspended particles. Observed LiF-etched Mxene yielded a higher density of particles and darker collected solution. Drop-cast (4 ml) supernate onto slides and dried with Ar. For Rhodamine B (RhB) testing, drop-cast 4 ml drops onto Mxene spots and dried with Ar. Scanning Electron Microscopy conditions: 10 kV Beam energy, high vacuum; Working distance of 8 mm; beam penetration depth appx. 4 microns, beam spot size appx. 2 nanometers. Results: Detection of aluminum correlates with bright spots on image. Presence of aluminum shows that LiF/HCl etching was less thorough than HF etching. Trace Cl detection in LiF images suggests incomplete rinsing. HF has smaller feature size, more layer structure, and increased homogeneity, consistent with expectations. Macroscopic Raman spectroscopy measurements: 532 nm excitation, ∼50 mW with a ∼100 micron spot size (InPhotonics RPB probe). Kaiser Optical Holospec f/1.8 spectrometer with cooled (-60 deg.C) Andor iDus OE420 CCD. LiF 1x supernate showed good signal for trace measurements of Rhodamine B. HF and 1/4x LiF supernates showed little Mxene or Rhodamine B signal. Low deposition densities led to excess background signal from glass slides. For LiF film, response is linear with Rhodamine B concentration over range tested. Will retest with Raman microscope (∼1 micron spot size) to characterize SERS of more dilute LiF and HF etched Mxenes. Conclusions: The LiF etched material was more suitable for macroscopic SERS measurements because it was more concentrated, resulting in a thicker film than the HF etched Mxene and diluted LiF sample. However, the other materials may give greater SERS enhancements, which we hope to determine from measurements with the Raman microscope. From characterization with SEM we concluded that the HF etched Mxene is more uniform/homogenous and has smaller particle size than the LiF etched Mxene. There is still aluminum present in both samples indicating that etching wasn't complete, but the removal of the aluminum was more efficient in the HF method. Path Forward: Observe SERS with Raman microscopy, to obtain better signals for the more diluted samples and be able to compare enhancement effects for the different MXenes. Characterize uranyl sorption into MXene films and test Raman and fluorescence signals. Revisit the etching conditions to improve removal of aluminum. FSU and SRNL will continue to collaborate to create and characterize different Mxene materials and test their usefulness for sensor applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Developing and Implementing New Waste Chemistry Controls for Hanford's Double-Shell Tanks - 20041

Waste chemistry controls for the Hanford double-shell tanks (DSTs) were established in the 1980's in response to tank failures caused by stress corrosion cracking (SCC) at the Savannah River Site (SRS). The controls were established based on a combination of SRS chemistry limits and corrosion testing results. Conditions in the Hanford DSTs have changed over time, with the temperature in the majority of the DSTs dropping below 50 deg. C. Testing indicated that the original chemistry control specification and SCC testing performed in 2010 did not protect against pitting corrosion mechanisms - what is believed to have caused the failure of tank 241-AY-102. New waste chemistry controls are necessary to protect the DSTs from both SCC and pitting corrosion. Savannah River National Laboratory (SRNL), with input from the Tank Integrity Expert Panel (TIEP) Corrosion Subgroup (CSG), performed a statistically based investigation of nitrate and halide ion induced pitting corrosion. The investigation was intended to develop a comprehensive waste chemistry envelope that minimizes the risk of both SCC and pitting caused by halide and nitrate ions. The waste chemistry envelope needed to be robust enough to address future waste retrieval and process changes which could significantly change the waste composition of the DSTs. The experimental design allowed the statistically significant ions and their effect on pitting corrosion to be determined. SRNL developed the 'pitting factor' which is an empirical relationship between the statistically significant inhibitive species (hydroxide, and nitrite), and pitting inducing species (nitrate, chloride, and fluoride). The coefficients are weighted factors that show the degree of influence the species have on the propensity for pitting. New waste chemistry control limits were recommended by SRNL, and concurred with by the TIEP CSG, that incorporated the pitting factor along with other limits. The controls developed to reduce the risk of pitting corrosion were evaluated to determine if they also protected against SCC. Hundreds of test results were reviewed and compared against the proposed limits. With the exception of one test result, instances where cracking was observed corresponded to chemistry that was outside of the proposed limits - indicating that the chemistry controls developed for pitting also adequately addressed SCC concerns. Existing tank composition estimates were evaluated against the new chemistry controls - three current tank chemistries are suspect, and may not meet the new chemistry control requirements. These included the interstitial liquid (liquid associated with solids) of DSTs 241-AN-102, 241-AN-106, 241-AN-107, and 241-AY-101. Measures are ongoing to evaluate the tanks with the suspect chemistry. These include varying combinations of: performing additional evaluations (history of use, modeling); DST specific laboratory testing; and, pursuing core samples of the DSTs. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

When Every Drum is a Win - Tackling a Thirty-Five Thousand Drum Legacy - 20064

Cameco Corporation's (Cameco) Port Hope Conversion Facility (PHCF) was previously owned by the federal Crown Corporation, Eldorado Nuclear, which held a significant inventory of legacy waste material at the time Cameco was formed in 1988. As a result, Cameco was granted an allocation of 150,000 cubic metres of space in the Long-Term Waste Management Facility (LTWMF) located in the Municipality of Port Hope (MPH), which opened to the receipt of Cameco material in June 2018. Cameco is currently undertaking a major site cleanup and renewal of its Port Hope Conversion Facility (PHCF) which is known as the Vision in Motion (VIM) project. Over its operating history, Eldorado accumulated an inventory of over 35,000 drums of accumulated waste that was primarily stored at two offside warehouse locations. In 2017 and 2018, the project focused on repackaging two well characterized legacy wastes (magnesium fluoride slag and depleted uranium titanium oxide) from one of the two offsite locations. At the conclusion of this work, approximately 15,000 drums of these wastes had been repackaged and disposed of at the LTWMF. There remained approximately 1000 drums from this location that either could not be repackaged safely or were different waste types and required further verification and/or processing. The buildings at this location were scheduled for demolition in early 2019, which triggered the development of a process for triaging legacy drums in August 2018, which allowed for preparation and shipment of approximately half of these drums to the LTWMF by March 2019, with the remainder moved to the second offsite warehouse location in February 2019 for further characterization which is ongoing. This paper will discuss key lessons learned as the drummed legacy waste disposal inventory has been reduced to approximately half of the initial inventory. This will include the development of an alternate packaging process; prioritization of characterization activities and selection of techniques where minimal inventory information is available; determination of next step(s) for each drum as it is assessed; key safety considerations; and how to make inroads into an overwhelming task while under public and regulatory scrutiny. In a relatively short period of time, significant progress has been made to organize and gather information about the legacy waste, update the inventory records and determine the most appropriate pathways (i.e. LTWMF disposal, disposal at another appropriate facility, site storage until future processing and/or disposal). Since 2017 the volume of the decades-old legacy waste inventory has decreased significantly. With the majority of the known materials safely disposed of at the LTWMF, every drum removed from the endless rows of 20,000 pyramidally-stacked waste drums with limited history that is safely characterized, prepared and shipped is considered a win. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A Rapid Sequential Separation Method for Determination of Actinides and TENORM in Fracking Wastes - 20223

With recent advances in unconventional drilling technology in the US and around the world, the risks of environmental contamination and exposure due to technologically enhanced naturally occurring radioactive materials (TENORM) from fracking wastes have also surfaced. Although the Permian Basin (southeastern New Mexico, western Texas) has long been a modest producer of oil, the advent of fracking technology a decade ago turned it into hot property for producers. A 2018 assessment of undiscovered, technically recoverable continuous oil and gas resources by the U.S. Geological Survey estimates an average 46.3 billion barrels of oil and 281 trillion cubic feet of gas. This is likely to increase the use of unconventional drilling and TENORM generation. TENORM concentrations in oil and gas exploration and production waste can be several hundred to several thousand times higher than background TENORM concentrations. Both the thorium and uranium decay chains contribute to airborne radionuclides arising from the radon gas escaping the ground and subsequently decaying as airborne particulates. Additionally, radon decay products {sup 210}Pb and {sup 210}Po can build up in scale on the internal surfaces of oil and gas handling pipes and in sludge in refineries, becoming potential inhalation and ingestion hazards for workers. Furthermore, southeastern NM is also home to world's only licensed and operating transuranic nuclear waste repository, the DoE's Waste Isolation Pilot Plant (WIPP). Plutonium isotopes ({sup 239+240}Pu) and {sup 241}Am, are expected to account for more than 99% of the total radioactivity scheduled for disposal in the WIPP repository. Thus, an improved understanding of the environmental fate and transport of TENORM, liberated by unconventional drilling, is essential to assess how best to protect individuals and the environment. In this context, accurate measurement of TENORM and actinides in environmental and biological samples is essential. In this presentation, a new sequential method for the separation and pre-concentration of actinides (Pu, Am, Np) and TENORM (Po, U and Th) derived from oil and gas exploration is proposed. The TEVA method involves a rapid co-precipitation step to remove matrix interferences from the samples, followed by plutonium oxidation state adjustment to Pu (IV) and an incubation period of ∼ 1 hour at 50-60 deg. C to allow the resultant Po (II) to oxidize into Po(IV). The polonium, neptunium, thorium and plutonium are then separated on a TEVA column, while americium and uranium are separated on a TRU column. After separation, the alpha counting source was prepared by micro-precipitation with copper sulfide (CuS) for polonium and neodymium fluoride (NdF{sub 3}) for actinides. The efficiency and reliability of the procedures were tested by analyzing filter, drinking water and frack sand samples. The method is simple, robust and can be performed quickly with excellent removal of interferences, high chemical recovery and very good alpha peak resolution. (authors)

07 ISOTOPE AND RADIATION SOURCES↗

Benchmark Study of Infinite Lattice of Pebble Fuel within FLiBe Coolant for TMSR-SF1 Design

Solid Fueled Thorium Molten Salt Reactor (TMSR-SF1) is Chinese Fluoride-salt-cooled High Temperature Reactor (FHR) designed by the TMSR group. The construction of this test reactor is expected in the near years. Using TRISO particle based pebble fuel leads to various challenges in neutronics modeling, such as double heterogeneity effect, preserving exact number of particles, their random distributions in pebble, and etc. For the purpose of verifying the calculations, benchmark study of infinite lattice of pebble fuel within FLiBe coolant for the TMSR-SF1 design has been performed. Back-to-back comparisons have been made between TMSR and MIT researchers using different Monte-Carlo based codes. Very good agreements have been found and the results quantitatively evaluate the neutronic effect of various modeling approaches. In addition, sensitivity study has been carried out for the reference pebble-bed fuel lattice. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Machine Learning Based System Performance Prediction Model for Transportable FHR

A machine learning based system performance prediction model is currently created to support the development of autonomous control for small reactors, such as the Transportable Fluoride-salt-cooled High-temperature Reactor (TFHR), which has a 20 MWth compact core proposed by MIT for remote sites. The prediction model is constructed using support vector regression (SVR) with training data generated by RELAP5. A particle filtering framework is utilized to estimate and update model parameters with instrument measurements. Verifications of the prediction and filtering models have been carried out using TFHR reactivity insertion cases. Satisfactory performance in predicting the core behavior and in recognizing the inserted reactivity rate is concluded. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Sensitivity Analysis of Passive Heat Removal Capability of FHR Based on Efficient Surrogate Model and GenFlow

Code Scaling, Applicability and Uncertainty Evaluation Methodology (CSAU) is used for quantifying reactor safety margins and works as an alternative method for licensing nuclear power plant. In the framework of CSAU, sensitivity and uncertainty analysis (SA and UA) should be performed. However, for large-scale complicated thermal hydraulics analysis simulated by code (e.g. RELAP5, CFD and subchannel analysis, the sensitivity and uncertainty analysis is really time-consuming. Furthermore, sometimes it is not feasible to perform SA and UA. Specifically, the computation time for Monte Carlo sampling or advanced LHS sampling can be neglected, but the computation time for thermal hydraulics code makes up main part of time during SA and UA process. In order to accelerate the speed of SA and UA, thermal hydraulics code can be improved based on advanced mathematic algorithm or using parallel method. However, the development for new mathematic method needs long time and strict verification and validation process is needed for a new code, which usually takes a couple of years or even longer time to have an approved code that can be used in nuclear industry. An alternative way to improve the speed of SA and UA is using surrogate model. The surrogate model is derived from the input as well as output data of the original code, assuming the code as a black box. The most common method is using response surface method (RSM) as a surrogate for the code, the input parameters are then sampled from their assumed distribution and the corresponding value of the response surface function is calculated. However, a couple of input parameters need hundreds or even thousands of original code calculations. The large number of runs is an obvious disadvantage of this method. Besides, the second disadvantage is an appropriate response surface function must be selected (e.g. quadratic, cubic, quartic, with or without cross product terms, or using a non-polynomial form) to avoid the overfit and underfit problem. This process is time consuming and expensive. Polynomial chaos expansion method is a reasonably fast and attractive alternative, stochastic model. The chaos expansion provides an efficient high-order method of including non-linear effects in stochastic analysis. Usually, the information about the model parameters and their probability distribution is limited and the dependence between them is not known. However, if arbitrary polynomial chaos is used, instead of assuming probability distribution for input parameters which may introduces additional subjectivity into the analysis, the available information can directly and most purely be used in stochastic analysis based on arbitrary data distribution. Thus, it is not necessary to know the exact probability density functions to perform SA and UA based on arbitrary polynomial chaos (aPC). The aPC has been applied for uncertainty quantification in many fields (e.g. in solid mechanics, fluid flows, thermal sciences), and become widely used in nuclear industry recently. Mk1 PB-FHR is a small modular fluoride-salt-cooled, high-temperature reactors (FHRs) that is a concept design by University of California, Berkeley (UCB). It has inherently safe features like natural-circulation-driven systems (e.g. direct reactor auxiliary cooling system (DRACS)) to passively remove decay heat from the reactor core during design basis and beyond design. It is necessary to perform SA and UA, since the licensing process of this new kind of reactor is under way and there are many design parameters that have not been fixed. Current nuclear commercial codes, such as RELAP5, have mainly been developed for light water reactors, which require the use of comprehensive two-phase flow models. This capability is not required to simulate single-phase flow phenomena in FHRs, whose baseline coolant, flibe, remains liquid up to 1430 deg. C at atmospheric pressure. The FHR advanced natural circulation analysis (FANCY) code has been developed specifically for FHR technology modeling and validation work has been performed by using CIET data in UCB. The code has been renamed General Flow (GenFlow) because it has been further developed to have the capability to model complicated pipework system based on object-oriented concept for user friendly purpose. Besides, it can be used to simulate both the force circulation as well as natural circulation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Microstructure of In-Core Molten Salt Corrosion Hastelloy N{sup R} and 316 Stainless Steel

Since 2011, many materials have been discussed for potential application in Fluoride salt-cooled High-temperature nuclear Reactors (FHRs), which are emerging as leading reactor concept for the next generation of nuclear reactors thanks to the benefits of a high degree of passive safety, high thermal efficiency, and low spent fuel volume. Among these discussed materials, Hastelloy N{sup R} and 316L stainless steel have been selected as the most likely candidate alloys for FHRs. To provide direct experience in integrating a real system using molten FLiBe salt for reactor operation, these two candidate alloys were experimentally tested in Li-7 enriched Li{sub 2}BeF{sub 4} (FLiBe) molten salt in the core of MIT Research Reactor (MITR) at 700 deg. C for 1000 hours. After in-core corrosion testing, some basic post-irradiation examinations (PIE) including weight change per unit area and surface profile as well as surface morphology were conducted in the MIT Nuclear Reactor Laboratory (NRL) and compared with out-of-reactor corrosion samples. The deep understanding of these alloys in high-temperature molten salt with strong neutron irradiation requires further microstructural analysis such as electron microscopy and energy dispersive spectroscopy on the surface and cross-section of the in-core corrosion tested samples. The challenge in the microstructural analysis is due to the high radioactivity from the gamma emitting isotopes formed in alloys during neutron irradiation. Additionally, the facilities that are authorized for radioactive materials are very limited on campus. In this study, the microstructure of the in-core corrosion tested Hastelloy N{sup R} and 316L stainless steel specimen was analyzed by using the facilities at the Center for Advanced Energy Studies (CAES) at Idaho National Laboratory (INL) through the Nuclear Science User Facilities (NSUF) Rapid Turnaround Experiment (RTE) program.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Preliminary Results of Material Flow Controlled MSR Depletion Calculations

A versatile, parallelizable Python 2.7 library was developed in order to simulate once-through molten salt reactor depletion in a realistic manner via the coupled neutronics/depletion code Serpent 2. Realistic in this sense entails two aspects: reactivity of the core, and oxidation potential of the fuel. The core reactivity should be maintained near zero as with any nuclear reactor. Gross reactivity control is provided by variations of the refuel rate of the reactor. Fine reactivity adjustments are expected to be done with control mechanisms in real-life power operation. The Python library developed allows a user to set bounds on the desired ke f f value. Fuel oxidation potential must be controlled for any liquid fueled reactor. As a simple example, consider this fission where the fuel becomes more oxidizing: UF{sub 4} → SrF{sub 2} + Xe + 2F{sup -} It can be shown using expected fission product oxidation state data that for these reactors, the fuel will become more oxidizing over time as a result of accumulation of excess fluoride ion. Addition of a reducing agent to reactor fuel will be necessary in the operation of molten salt reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Update of the nuclear criticality slide rule calculations: studies with common shielding materials - 25467

This paper presents preliminary results from the third phase of the current update to the nuclear criticality slide rule, in which MCNP, MAVRIC/Monaco, and COG have simulated the prompt neutron and photon dose from critical spheres of 4.95% enriched uranyl fluoride solution and 93.2% enriched uranium metal. New to this phase is the inclusion of various thicknesses of lead, steel, concrete, and water shielding. This phase also evaluated the effects of humidity on the unshielded configurations in the first phase, as well as the effects of changing the ground composition used in the first phase from concrete to dry soil. The small sample of results presented show that MCNP, MAVRIC/Monaco, and COG results are statistically the same or different by only a few percent. The impact of the shielding materials depends on their thickness, but doses decreased by nearly a factor of 100 are presented. In a few instances, buildup of gamma doses occurs due to neutron interactions in shielding materials. (authors)

61 RADIATION PROTECTION AND DOSIMETRY↗

UK Regulatory experience with the criticality safety of transport package applications - 14519

The UK Government has created the Office for Nuclear Regulation (ONR) as an independent public body to ensure effective and efficient regulation of the nuclear industry in the UK. ONR brings together for the first time in the UK the regulation of nuclear safety, civil nuclear security, nuclear safeguards and the transport of radioactive substances within a single organization. Applications requesting approval to transport packages containing fissile material through the UK have been received for many decades from numerous organisations across the world. Each application is treated equally with the judgement of safety based on the information provided in the design safety report. In recent years, the ONR has questioned a number of criticality safety related assumptions; some of which have been held for many decades. The outcome from these discussions will be examined. Uranium hexafluoride (UF{sub 6}) has been transported across the world for many years, carried in 30B steel cylinders within a variety of overpacks. For simplicity, some criticality safety cases have not claimed for the presence of the overpack. However, it shall be shown that these safety cases will have difficulty in justifying the criticality safety of transporting uranium hexafluoride if credit for the overpack is not claimed. In addition, the applications that have been submitted for Competent Authority approval have made various assumptions regarding the shell thickness of the 30B cylinder, the distribution of the hydrogen fluoride (HF) impurity and the potential for the uranium hexafluoride residues to hydrolyse. The adequacy of these assumptions will be discussed in turn along with the need for the applicant to demonstrate compliance with any certificate restriction on the mass of heel (residue) allowed within the package. Uranium oxide (UO{sub 2}) powder is regularly transported around the world. For most designs, it is assumed that water will enter the package under accident conditions of transport. Under these conditions, a common assumption is that the grains of uranium oxide powder will evenly distribute within the water and internal volume of the package. The validity of this assumption from a realistic and pessimistic perspective will be challenged. It will then be shown that if instead the powder grains of uranium oxide are agglomerated together into larger sized groups, an increase in the k{sub eff} of the system of up to 2,000 pcm can occur. As packages are commonly loaded up to the criticality safety limit, an increase in k{sub eff} such as this is likely to be problematic. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

COUPLED MULTIPHYSICS PRIMARY LOOP SIMULATIONS OF THE Mk1-FHR IN THE VIRTUAL TEST BED

The Virtual Test Bed (VTB) repository hosts a wide range of challenge problems to showcase modeling and simulation capabilities to support advanced reactor demonstration. A coupled multiphysics model of the Mk1 pebble-bed fluoride-salt-cooled high-temperature reactor (PB-FHR) is presented here. The analysis leverages NEAMS tools (Griffin), SAM, Pronghorn, and the MOOSE heat conduction module) for core neutronics, thermal hydraulics of the core and the primary loop, and multiscale fuel performance simulations. The analysis was entirely created by coupling standalone simulations of the reactor previously available on the VTB. All input files and documentation developed for this example are available on the VTB website: \url{mooseframework.inl.gov/virtual_test_bed/}}. This model was featured in the NRIC Tech Talk presented in December 2021.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Linear pi-Acceptor-Templated Dynamic Clipping to Macrobicycles and[2]Rotaxanes

Functional rotaxanes are one of the representative nanoscale molecular machines that have found applications in many areas, including molecular electronics, nanoelectromechanical systems (NEMS), photo controllable smart surfaces, and nanovalves. With the advent of molecular recognition and self-assembly, such molecular compounds can now be obtained efficiently through template-directed synthesis. One of the common strategies of making [2]rotaxanes involves the clipping of a macrocycle around a preformed dumbbell-shaped template in a [1+1] or [2+2] manner. While early examples were based on irreversible kinetic pathway through covalent bond formation, recent advances on reversible dynamic covalent chemistry (DCC) has attracted great attention to this field. By virtue of thermodynamically controlled equilibria, DCC has provided highly efficient and versatile synthetic routes in the selection of specific products from a complex system. Among the several reversible reactions in the category of DCC reactions, the imine formation has proven to be very versatile in macrocyclization to give complex interlocked molecular compounds. Cryptands are three dimensional bicyclic hosts with preorganized cavities capable of inclusion of ions and small molecules. Replacing the nitrogen bridgeheads in common cryptands with aromatic ring systems gives cyclophane-based macrobicycles. The introduction of aromatic ring systems into a preorganized cage-like geometry facilitates ion-{pi} interactions and {pi}-{pi} interactions, resulting in novel metal sandwiches, fluoride receptors, and host-guest complexes. In particular, the seminal work by Gibson, Huang and coworkers on cryptand complexation with paraquat and diquat guests have resulted in the efficient synthesis of mechanically interlocked rotaxanes. The synthesis of cyclophane-based macrobicycles, however, was mostly realized through multiple reaction steps and in high-dilution conditions, which often suffered from low yield and tedious workup. Thus, a one-step, five-component [2+3] clipping reaction that can give the desired macrobicycle is highly desirable. We are motivated by a {pi}-guest templating protocol, because not only {pi}-{pi} interactions can contribute to the formation of macrobicycles, but also the resulting host-guest system holds great promise as a forerunner in the construction of interlocked molecules. (Scheme 1c) Very simple precursors, namely 1,3,5-benzenetrialdehyde (1) and 2,2{prime}-(ethylenedioxy)diethylamine (2) were chosen as the components for desired macrobicycle. (Scheme 2) The formation of six imine bonds would connect the five components to give a macrobicycle while extending the conjugation in the C{sub 3}-symmetric aromatic 'ceiling' and 'floor', which is suitable for enhancing the {pi}-{pi} interactions with a complementary aromatic template. Meanwhile, the ethylene glycol 'pillars' can provide sufficient flexibility, proper spacing, and polar binding sites to assist guest encapsulation. Initial screening of ?-templates engaged several C{sub 3} symmetric aromatic compounds in order to match the symmetry of the desired macrobicycle, which only resulted in nonspecific mixtures. It was found instead that linear bipyridinium (BPY) containing guests effectively templated the [2+3] clipping reaction. Based on this protocol, a [2]rotaxane was successfully assembled as the single product from the six-component reaction.

36 MATERIALS SCIENCE↗