Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Experimental Methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Experimental validation of a high voltage pulse measurement method.

This report describes X-cut lithium niobate s (LiNbO3) utilization for voltage sensing by monitoring the acoustic wave propagation changes through LiNbO3 resulting from applied voltage. Direct current (DC), alternating current (AC) and pulsed voltage signals were applied to the crystal. Voltage induced shift in acoustic wave propagation time scaled quadratically for DC and AC voltages and linearly for pulsed voltages. The measured values ranged from 10 - 273 ps and 189 ps 2 ns for DC and non-DC voltages, respectively. Data suggests LiNbO3 has a frequency sensitive response to voltage. If voltage source error is eliminated through physical modeling from the uncertainty budget, the sensor s U95 estimated combined uncertainty could decrease to ~0.025% for DC, AC, and pulsed voltage measurements.

Cular, Stefan↗

Implementation of an Experimental Setup Based on the Three-Omega Method for Thermal Conductivity Measurements of Molten Salts

Molten salt reactors (MSRs) are one of the most promising next-generation nuclear reactor designs which use molten salts as the fuel and coolant. To design, model, predict, license, and operate MSRs, the behavior of the fuel and coolant must be understood as a function of temperature and irradiation, i.e., burnup. Of particular importance and complexity is the reliable and reproducible measurement of thermal conductivity of molten salts at high temperatures (> 500 °C). Thermal conductivity provides information on the rate at which heat passes through a specified material and is dependent on chemical composition. Currently, in the national laboratory complex, several methods for measuring thermal conductivity on molten salt systems are under development, however, to date, consistent data have not been produced. Typically, thermal conductivity measurements of high-temperature melts have been conducted by using the Transient Hot Wire (THW) method where thermal conductivity is determined by the change in temperature over time at a certain distance from a heating wire. Another time-dependent technique is the laser flash method, commonly used for solid samples. Laser flash requires prior measurements of density and heat capacity to calculate the thermal conductivity of the sample, introducing additional measurement errors. Steady state and time-dependent measurements such as THW and laser flash have errors from convection and ambient temperature fluctuations (heat radiation). In order to produce high fidelity thermal conductivity data, a measurement technique needs to be developed that will reduce the effect of convection at high temperatures by measuring in a very fast time window. In addition, to measure on actinide and irradiated salts the sample size should be small. Therefore, this project aims to develop a frequency-domain technique based on the three-omega (3?) method, previously proven to work on solids, nanofluids and low temperature solar salts (25 to 250 °C). If the 3?-device can be designed with materials that can withstand high temperatures (>500 °C) and can be configured to reduce errors due to convection, then it would prove to be a valuable technique for ensuring thermal conductivity on molten salt systems needed for MSR development. For this proposal, the 3? instrument will be designed, assembled, and tested on non-radioactive salts before being used on actinide bearing salts. In addition, a thermal model will be developed to determine the thermal conductivity of the sample from the measured thermal oscillation of the sensor. Because 3? is a direct method that requires a small volume of sample and works in a very fast time window, it will aid in suppressing the interference due to convection which is ideal when working with high temperature liquid samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An Experimental Study of Uncertainty Considerations Associated with Predicting Auto-ignition Timing using Livengood-Wu Integral Method

The application of the Livengood-Wu (LW) integral method as a tool to estimate knock onset in spark ignited (SI) engines and combustion phasing in advanced compression ignition (ACI) engines has been demonstrated through simulations several times. In this study, the effect of uncertainties associated with parameters required for the LW integral method, when used as a tool for model based control of ignition timing in an ACI engine, were experimentally studied using five full boiling range gasoline fuels. As a first step, the method was applied to experimental data from a rapid compression machine and it was found that the ability of the LW integral method to predict ignition timing was very sensitive to the performance of the chemical kinetic model of each fuel. The method was subsequently applied to experimental data from a single-cylinder gasoline engine with simple approximations for the LW integral input parameters, and it was found that the predicted time of ignition was significantly different from the actual start of combustion. Systematic evaluation of various parametric uncertainties conducted thereafter showed that the uncertainty in cylinder charge temperature has the greatest influence. Improved methods of estimating cylinder charge temperature are proposed to account for the previously determined corrections, to enable the use of the LW integral method for model based control of ignition timing.

Compression Ignition↗

Effects of biaxial strain on the improper multiferroicity in h – LuFe O 3 films studied using the restrained thermal expansion method

Elastic strain is potentially an important approach in tuning the properties of the improperly multiferroic hexagonal ferrites, the details of which have however been elusive due to the experimental difficulties. Employing the method of restrained thermal expansion, we have studied the effect of isothermal biaxial strain in the basal plane of h-LuFeO 3 (001) films. The results indicate that a compressive biaxial strain significantly enhances the K 3 structural distortion (the order parameter of the improper ferroelectricity), and the effect is larger at higher temperatures. The compressive biaxial strain and the enhanced K 3 structural distortion together, cause an increase in the electric polarization and a reduction in the canting of the weak ferromagnetic moments in h-LuFeO 3 , according to our first principle calculations. These findings are important for understanding the strain effect as well as the coupling between the lattice and the improper multiferroicity in h-LuFeO 3 . Finally, the experimental elucidation of the strain effect in h-LuFeO 3 films also suggests that the restrained thermal expansion can be a viable method to unravel the strain effect in many other thin film materials.

36 MATERIALS SCIENCE↗

Temporal and spatial effects of ablation plume on number density distribution of droplets in an aerosol measured by laser-induced breakdown

We proposed and experimentally demonstrated a novel method of evaluating the number density of droplets in an aerosol by laser-induced breakdown. The number density of droplets is evaluated from the volume in which the laser intensity exceeds the breakdown threshold intensity for droplets, and the number of droplets in this volume, which is evaluated by the experimentally observed breakdown probability. This measurement method requires a large number of laser shots for not only precise measurement but also highly temporally and spatially resolved density distribution in aerosol. Laser ablation plumes ejected from liquid droplets generated by breakdown disturb the density around the measurement points. Therefore, the recovery time of the density determines the maximum repetition rate of the probe laser irradiating a fixed point. The expansion range of the ablation plume determines the minimum distance at which the measurement points are unaffected by a neighboring breakdown when multiple laser beams are simultaneously irradiated. These laser irradiation procedures enable the measurement of the number density distribution of droplets in an aerosol at a large number of points within a short measurement time.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Practical and Optimal Sequential Bayesian Experimental Design for Complex Systems Incorporating Human Experimenter Preferences (Final Scientific/Technical Report)

Experiments are indispensable for developing models of complex systems. Carefully designed experiments can provide substantial savings for these expensive data-acquisition opportunities. However, designs based on heuristics are often suboptimal for systems with multiphysics, nonlinear dynamics, and uncertain and noisy environments. Optimal experimental design, while leveraging predictive models, seeks to systematically quantify and maximize the value of experiments. In this project, we focused on the design of multiple experiments, where current approaches are largely suboptimal: batch-design does not adapt to new data acquired during the experiment campaign (no feedback), and greedy/myopic design ignores future dynamics and consequences (no lookahead). We developed the mathematical framework and computational methods for sequential optimal experimental design (sOED) for complex systems. We enabled tractable model-based sOED in a rigorous manner through novel algorithms based on reinforcement learning, and investigated the effects of human experimenters on the design process. Our methods are fully Bayesian, able to quantify and update uncertainty in a principled manner. The traits aimed by our approach—mathematical rigor and optimality, human effects and uncertainty quantification, computational practicality—are crucial for elevating the standards of artificial intelligence (AI) to support decision-making in scientific domains, and contribute toward trust and realistic adoption of AI in experimental design practice.

97 MATHEMATICS AND COMPUTING↗

Comparing the Expense and Accuracy of Methods to Simulate Atomic Vibrations in Rubrene

Atomic vibrations can inform about materials properties from hole transport in organic semiconductors to correlated disorder in metal–organic frameworks. Currently, there are several methods for predicting these vibrations using simulations, but the accuracy–efficiency tradeoffs have not been examined in depth. In this work, rubrene is used as a model system to predict atomic vibrational properties using six different simulation methods: density functional theory, density functional tight binding, density functional tight binding with a Chebyshev polynomial-based correction, a trained machine learning model, a pretrained machine learning model called ANI-1, and a classical forcefield model. The accuracy of each method is evaluated by comparison to the experimental inelastic neutron scattering spectrum. All methods discussed here show some accuracy across a wide energy region, though the Chebyshev-corrected tight-binding method showed the optimal combination of high accuracy with low expense. We then offer broad simulation guidelines to yield efficient, accurate results for inelastic neutron scattering spectrum prediction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of Uncertainty Impacts on Emissions and Fuel Economy Evaluation for Chassis Dynamometer Testing

This study illustrates a methodology for quantifying the uncertainties encountered in the measurement of tailpipe emissions and in the fuel consumption measurements for light-duty conventional vehicles tested on a four-wheel drive chassis dynamometer. The study leverages high-fidelity experimental data collected over three standard drive cycles, UDDS, HWY and US06, intended to simulate a wide range of operating conditions. Here, a method is developed to estimate the measurement uncertainties in fuel consumption for a test cycle, which occur due to the accumulation of measurement uncertainties propagated through the system. The uncertainty determination model uses statistical analysis and standard propagation techniques to evaluate and combine the uncertainties introduced from various sources (including the vehicle, chassis dynamometer, driver, and instrumentation). The analysis also examines three different experimental methods for determining the fuel consumption: 1) carbon mass balance, 2) volumetric fuel scale and 3) gravimetric fuel scale, and takes into consideration the properties of the instrumentation used. The results show that the most significant influence on the determination of the emissions comes from the concentration measurement, and similarly the biggest impact on the total fuel consumption uncertainty comes from the uncertainty in the determination of the carbon dioxide mass, due to the large presence of this pollutant in the overall emissions. It was found that the fuel consumption uncertainties are in the range of ±1-2% for all three methods analyzed, with the lowest values being obtained for measurements performed using the gravimetric method for all three drive cycles considered.

33 ADVANCED PROPULSION SYSTEMS↗

Using discrete Bayesian networks for diagnosing and isolating cross-level faults in HVAC systems

Fault detection and diagnosis (FDD) technologies are critical to ensure satisfactory building performance, such as reducing energy wastes and negative impacts on occupant comfort and productivity. Existing FDD technologies mainly focus on component-level FDD solutions, which could lead to mis-diagnosis of cross-level faults in heating, ventilating, and air-conditioning (HVAC) systems. Cross-level faults are those faults that occur in one component or subsystem, but cause operational abnormalities in other components or subsystems, and result in a building level performance degradation. How to effectively diagnose the root cause of a cross-level fault is the focus of this study. Here, this paper presents a novel discrete Bayesian Network (DisBN)-based method for diagnosing cross-level faults in an HVAC system commonly used in commercial buildings. A two-level DisBN structure model is developed in this study. The parameters used in the DisBN model are obtained either from expert knowledge or through machine-learning strategies from normal system operation data. Meanwhile, the probability parameters are discretized to incorporate the uncertainties associated with typical expert knowledge. Thus, the developed DisBN method addresses the challenges many other BN based FDD methods face, i.e., the lack of fault data for BN parameter training. The developed DisBN represents causal relationships between a fault and its cross-level system impacts (i.e., fault symptoms or fault indicators) by considering how fault impacts propagate across different levels in an HVAC system. A weather and schedule information-based Pattern Matching (WPM) method is employed to automatically create WPM baseline data sets for each incoming real time snapshot data from the building systems. Consequently, BN inference and real-time diagnostics are achieved by comparing incoming snapshot data and the WPM baseline data set. The proposed method is evaluated using experimental fault data collected in a campus building. Fault diagnosis results demonstrate that the WPM-DisBN method is effective at locating the root causes of cross-level faults in an HVAC system.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Descriptors for Electrolyte-Renormalized Oxidative Stability of Solvents in Lithium-Ion Batteries

Electrolyte stability against oxidation is an important factor limiting the development of high energy density batteries. The highest occupied molecular orbital (HOMO) level of solvent molecules has been traditionally used for understanding trends in their oxidative stability, but this assumes a noninteracting environment. However, solvent HOMO levels are renormalized because of molecules in their solvation shells. In this work, we first demonstrate an inexpensive and accurate method to determine the HOMO level of the solvent followed by simple descriptors for renormalization of the HOMO level due to different electrolyte components. The descriptors are based on Gutmann donor and acceptor numbers of the solvent and other components. The method uses fast generalized gradient approximation-level density functional theory calculations compared to previously used expensive, experimental data-dependent methods. This method can be used to screen for unexplored stable solvents among the large number of known organic compounds to design novel high-voltage stable electrolytes.

25 ENERGY STORAGE↗

Zinc Diffusion into InP via a Narrow Gap from a Planar Zn{sub 3}P{sub 2}-Based Source

An original technology of zinc diffusion into InP via a narrow gap is described, which allows reproducible formation of p–n junctions with preset depth of doping and retained surface morphology of the doped layers. Using the proposed method, desired charge carrier distribution profiles in Zn-doped InP layers were obtained. It has been experimentally confirmed that the method of cross-sectional scanning electron microscopy allows to precision measure of the zinc diffusion depth.

36 MATERIALS SCIENCE↗

A Comparative Study of Joint Modeling Methods and Analysis of Fasteners [Slides]

Motivation: Crucial aspect of mechanical design is joining methodology of parts. Ability to analyze joint and fasteners in system for structural integrity is fundamental. Different modeling representations of fasteners include spring, beam, and solid elements. Various methods compared for linear system to decide method appropriate for design study. New method for modeling fastener joint is explored from full system perspective. Analysis results match well with published experimental data for new method.

42 ENGINEERING↗

Reactor physics benchmark experiments at the JSI TRIGA MARK II reactor - Current status and future outlook

Full text of publication follows. With the development of new high-fidelity computational methods, improvement of nuclear data, and multiphysics modelling, there is an increased need for benchmark experiments to experimentally validate the models, methods and input data. Many of the nuclear facilities designed to perform reactor physics benchmark experiments have been shut down. Therefore, research reactors offer a great opportunity for benchmark experiments, if they are well designed and performed with great care and accuracy. In this presentation we provide an overview of the past and ongoing activities related to benchmark experiments at the Jozef Stefan Institute TRIGA Mark II research reactor. The following experiments have been performed: criticality with fresh fuel, {sup 197}Au(n,γ) and {sup 27}Al(n,α) reaction rates in irradiation channels, absolute and relative {sup 197}Au(n,γ), {sup 235}U(n,f) and {sup 238}U(n,f) reaction rates in the core, burnup, kinetic parameters, control rod worth, isothermal reactivity coefficient, self-shielding, slow and fast (pulse) transients, nuclear heating, delayed and prompt gamma ray production, temperature profiles for multi-physics. Since the existing fleet of research reactors is ageing very rapidly and new experiments are needed, new research reactors should be designed and built to meet the needs of future advanced reactors, education and training, and other technologies in the coming years. We will review planned activities at the JSI TRIGA reactors and plans for the new research reactor in Slovenia. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Supercontinuum Fourier transform spectrometry with balanced detection on a single photodiode

We demonstrate a method of combining a supercontinuum light source with a commercial Fourier transform spectrometer, using a novel approach to dual-beam balanced detection, implemented with phase-sensitive detection on a single light detector. A 40 dB reduction in the relative intensity noise is achieved for broadband light, analogous to conventional balanced detection methods using two matched photodetectors. Unlike conventional balanced detection, however, this method exploits the time structure of the broadband source to interleave signal and reference pulse trains in the time domain, recording the broadband differential signal at the fundamental pulse repetition frequency of the supercontinuum. The method is capable of real-time correction for instability in the supercontinuum spectral structure over a broad range of wavelengths and is compatible with commercially designed spectrometers. A proof-of-principle experimental setup is demonstrated for weak absorption in the 1500-1600 nm region.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental phasing for structure determination using membrane-protein crystals grown by the lipid cubic phase method

Very little information is available in the literature concerning the experimental heavy-atom phasing of membrane-protein structures where the crystals have been grown using the lipid cubic phase (in meso) method. In this paper, pre-labelling, co-crystallization, soaking, site-specific mercury binding to genetically engineered single-cysteine mutants and selenomethionine labelling as applied to an integral membrane kinase crystallized in meso are described. An assay to assess cysteine accessibility for mercury labelling of membrane proteins is introduced. Despite the marked increase in the number of membrane-protein structures solved using crystals grown by the lipid cubic phase or in meso method, only ten have been determined by SAD/MAD. This is likely to be a consequence of the technical difficulties associated with handling proteins and crystals in the sticky and viscous hosting mesophase that is usually incubated in glass sandwich plates for the purposes of crystallization. Here, a four-year campaign aimed at phasing the in meso structure of the integral membrane diacylglycerol kinase (DgkA) from Escherichia coli is reported. Heavy-atom labelling of this small hydrophobic enzyme was attempted by pre-labelling, co-crystallization, soaking, site-specific mercury binding to genetically engineered single-cysteine mutants and selenomethionine incorporation. Strategies and techniques for special handling are reported, as well as the typical results and the lessons learned for each of these approaches. In addition, an assay to assess the accessibility of cysteine residues in membrane proteins for mercury labelling is introduced. The various techniques and strategies described will provide a valuable reference for future experimental phasing of membrane proteins where crystals are grown by the lipid cubic phase method.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Review: Pre-Darcy flows in low-permeability porous media

The widely used Darcy’s law specifies a linear relation between the Darcy velocity of fluid flow and the pressure gradient that drives the flow. However, studies have shown that Darcy velocity can exhibit a nonlinear dependence on the pressure gradient in low-permeability porous media such as clay and shale when the pressure gradient is adequately low. This phenomenon is referred to as low-velocity non-Darcian flow or pre-Darcy flow. This paper provides a comprehensive review of the theories, experimental data, and modeling methods for pre-Darcy flow in low-permeability porous media. The review begins by outlining the fundamental mechanisms underlying pre-Darcy flow that regulate the unique characteristics such as nonlinear dependence of the Darcy velocity on the pressure gradient and its relevance to fluid–rock interactions. The review then proceeds to present a thorough compilation of experimental investigations performed in various low-permeability geomaterials including tight sandstones, shales, and clays. Next, empirical and theoretical models and simulation methods that have been developed to fit and interpret experimental data are reviewed. Finally, the review underscores the challenges encountered in conducting and interpreting pre-Darcy flow experiments and suggests future research directions. By analyzing previous experimental investigations, this review aims to offer a valuable resource for researchers and practitioners seeking to enhance their understanding of fluid dynamics in low-permeability geomaterials. This provides insights into the application of pre-Darcy flow in numerous natural and engineered processes such as shale oil and gas recovery, contaminant transport in low-permeability aquifers, and geological disposal of nuclear waste.

58 GEOSCIENCES↗

RIPL - Reference Input Parameter Library for Calculation of Nuclear Reactions and Nuclear Data Evaluations

We describe the physics and data included in the Reference Input Parameter Library, which is devoted to input parameters needed in calculations of nuclear reactions and nuclear data evaluations. Advanced modelling codes require substantial numerical input, therefore the International Atomic Energy Agency (IAEA) has worked extensively since 1993 on a library of validated nuclear-model input parameters, referred to as the Reference Input Parameter Library (RIPL). A final RIPL coordinated research project (RIPL-3) was brought to a successful conclusion in December 2008, after 15 years of challenging work carried out through three consecutive IAEA projects. The RIPL-3 library was released in January 2009, and is available on the Web through (http://www-nds.iaea.org/RIPL-3/). This work and the resulting database are extremely important to theoreticians involved in the development and use of nuclear reaction modelling (ALICE, EMPIRE, GNASH, UNF, TALYS) both for theoretical research and nuclear data evaluations. The numerical data and computer codes included in RIPL-3 are arranged in seven segments: MASSES contains ground-state properties of nuclei for about 9000 nuclei, including three theoretical predictions of masses and the evaluated experimental masses of Audi et al. (2003). DISCRETE LEVELS contains 117 datasets (one for each element) with all known level schemes, electromagnetic and {gamma}-ray decay probabilities available from ENSDF in October 2007. NEUTRON RESONANCES contains average resonance parameters prepared on the basis of the evaluations performed by Ignatyuk and Mughabghab. OPTICAL MODEL contains 495 sets of phenomenological optical model parameters defined in a wide energy range. When there are insufficient experimental data, the evaluator has to resort to either global parameterizations or microscopic approaches. Radial density distributions to be used as input for microscopic calculations are stored in the MASSES segment. LEVEL DENSITIES contains phenomenological parameterizations based on the modified Fermi gas and superfluid models and microscopic calculations which are based on a realistic microscopic single-particle level scheme. Partial level densities formulae are also recommended. All tabulated total level densities are consistent with both the recommended average neutron resonance parameters and discrete levels. GAMMA contains parameters that quantify giant resonances, experimental gamma-ray strength functions and methods for calculating gamma emission in statistical model codes. The experimental GDR parameters are represented by Lorentzian fits to the photo-absorption cross sections for 102 nuclides ranging from {sup 51}V to {sup 239}Pu. FISSION includes global prescriptions for fission barriers and nuclear level densities at fission saddle points based on microscopic HFB calculations constrained by experimental fission cross sections.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Measuring the elastic modulus and residual stress of freestanding thin films using nanoindentation techniques

A new method is proposed to determine the elastic modulus and residual stress of freestanding thin films based on nanoindentation techniques. The experimentally measured stiffness-displacement response is applied to a simple membrane model that assumes the film deformation is dominated by stretching as opposed to bending. Dimensional analysis is used to identify appropriate limitations of the proposed model. Experimental verification of the method is demonstrated for Al/0.5 wt% Cu films nominally 22 {micro}m wide, 0.55 {micro}m thick, and 150, 300, and 500 {micro}m long. The estimated modulus for the four freestanding films match the value measured by electrostatic techniques to within 2%, and the residual stress to within 19.1%. The difference in residual stress can be completely accounted for by thermal expansion and a modest change in temperature of 3 C. Numerous experimental pitfalls are identified and discussed. Collectively, these data and the technique used to generate them should help future investigators make more accurate and precise measurements of the mechanical properties of freestanding thin films using nanoindentation.

36 MATERIALS SCIENCE↗