Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Effective diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

A Microfabricated Segmented-Involute-Foil Regenerator for Enhancing Reliability and Performance of Stirling Engines. Phase III Final Report for the Radioisotope Power Conversion Technology NRA

Under Phase III of NASA Research Announcement contract NAS3-03124, a prototype nickel segmented-involute-foil regenerator was microfabricated and tested in a Sunpower Frequency-Test-Bed (FTB) Stirling convertor. The team for this effort consisted of Cleveland State University, Gedeon Associates, Sunpower Inc. and International Mezzo Technologies. Testing in the FTB convertor produced about the same efficiency as testing with the original random-fiber regenerator. But the high thermal conductivity of the prototype nickel regenerator was responsible for a significant performance degradation. An efficiency improvement (by a 1.04 factor, according to computer predictions) could have been achieved if the regenerator was made from a low-conductivity material. Also, the FTB convertor was not reoptimized to take full advantage of the microfabricated regenerator s low flow resistance; thus, the efficiency would likely have been even higher had the FTB been completely reoptimized. This report discusses the regenerator microfabrication process, testing of the regenerator in the Stirling FTB convertor, and the supporting analysis. Results of the pre-test computational fluid dynamics (CFD) modeling of the effects of the regenerator-test-configuration diffusers (located at each end of the regenerator) are included. The report also includes recommendations for further development of involute-foil regenerators from a higher-temperature material than nickel.

Ibrahim, Mounir B.↗
NASA NTRS2006

Updated Computational Model of Cosmic Rays Near Earth

An updated computational model of the galactic-cosmic-ray (GCR) environment in the vicinity of the Earth, Earth s Moon, and Mars has been developed, and updated software has been developed to implement the updated model. This model accounts for solar modulation of the cosmic-ray contribution for each element from hydrogen through iron by computationally propagating the local interplanetary spectrum of each element through the heliosphere. The propagation is effected by solving the Fokker-Planck diffusion, convection, energy-loss boundary-value problem. The Advanced Composition Explorer NASA satellite has provided new data on GCR energy spectra. These new data were used to update the original model and greatly improve the accuracy of prediction of interplanetary GCR.

ONeill, Patrick M.↗
DOE OSTI2025

Computational Modeling of Molten Salt Infiltration and Oxidation in Nuclear Graphite

Graphite is utilized as a moderator and reflector in advanced nuclear reactor designs due to its high thermal conductivity, neutron moderation properties, and resistance to radiation damage. However, its longterm performance and reliability are challenged by degradation mechanisms such as molten salt infiltration in molten salt reactors (MSRs) and oxidation in gas-cooled reactors (GCRs). These mechanisms can compromise the structural integrity and operational lifetime of graphite components, necessitating a more detailed assessment of their physical behavior. This report focuses on the development of computational models for molten salt infiltration and oxidation of graphite to aid the design and performance analysis of graphite components. For molten salt infiltration, a computational framework is developed that couples incompressible Navier-Stokes and phase-field model to simulate the penetration of molten salt into graphite?s interconnected pore structure. Initial model verification is performed using two-phase flows in two dimensions, demonstrating the models ability to capture fundamental physical behavior and agree with analytical solution. This framework is then applied to a realistic IG110 nuclear graphite , where a computed tomography extracted pore geometry is used to analyse the infiltration behavior of FLiNaK molten salt. This model provides insights into how the microstructure and other relevant parameters influence the transport pathways of molten salt into graphite, potentially offering a means to rapidly evaluate a graphite grade?s resistance to infiltration. For oxidation, the report details pore-scale mass and heat transport models, describing the diffusion of gases, reaction kinetics, and thermal effects. Additionally, this report highlights inconsistencies in the existing volume-averaged macroscopic model, particularly in upscaling of reaction kinetics and flux terms, and surface to volume transformations. These inconsistencies suggest that current formulations may not accurately capture the experimentally observed graphite oxidation process, highlighting the need for improved model development. This work advances the development of physics-based computational models for graphite degradation, contributing to improved predictive models for next-generation nuclear reactor designs. Future efforts will focus on refining the infiltration model to address non-physical behaviors and enhance its robustness. Additionally, for oxidation, further studies will employ the principles of volume averaging to rigorously derive the upscaled equations, potentially in collaboration with subject matter experts.

Computational Modeling of Molten Salt Infiltration↗
DOE OSTI2025

Probing the Impact of Vacancy Diffusion on Void Dynamics at the Lithium Metal–Solid Electrolyte Interface

Lithium (Li) metal-based solid-state batteries (SSBs) are considered promising candidates for next-generation energy storage due to their superior energy density and enhanced safety compared to conventional Li-ion systems. However, their practical application is limited by challenges such as void formation at the Li-solid electrolyte (SE) interface, which disrupts ion transport and accelerates interfacial degradation. This work investigates how the coupled effects of electro-dissolution kinetics and surface diffusion at the Li metal surface govern the evolution of interfacial morphology during stripping. This work examines the influence of three distinct surface diffusion modes, which are terrace diffusion, step diffusion, and interlayer diffusion, on maintaining interfacial stability. In addition, how the dominant surface diffusion mechanism can overcome the contact loss due to high reaction kinetics is explored. Furthermore, the roughness of the Li metal anode surface is quantified, and the influence of different diffusion mechanisms on the evolution of the dynamic solid–solid interface is examined. The critical role of temperature in enhancing Li surface diffusivity and expanding the regime of stable contact is highlighted. By identifying distinct regimes of interface stability, this study analyzes how non-uniform electrochemical dynamics dictate void morphology evolution and interfacial contact. These insights offer guiding principles for engineering robust Li–SE interfaces in SSBs.

lithium metal anode↗
DOE OSTI2023

Phosphorus diffusion and deactivation during SiGe oxidation

Dopant profiles near the semiconductor–oxide interface are critical for microelectronic device performance. As the incorporation of Si 1−x Ge x into transistors continues to increase, it is necessary to understand the behavior of dopants in Si 1−x Ge x . In this paper, the diffusion and electrical activation of phosphorus within a strained, single-crystal Si 0.7 Ge 0.3 layer on Si during oxidation are reported. Both layers were uniformly doped, in situ, with an average phosphorus concentration of 4 × 10 19 atoms/cm 3 . After high-temperature oxidation, secondary ion mass spectrometry measurements revealed that the bulk of the phosphorus diffuses out of only the SiGe layer and segregates at the oxidizing SiGe–SiO 2 interface. Hall effect measurements corroborate the observed phosphorus loss and show that the phosphorus diffusing to the oxidizing interface is electrically inactive. Through density functional theory (DFT) calculations, it is shown that phosphorus interstitials prefer sites near the SiGe–SiO 2 interface. Finally, based on a combination of experimental data and DFT calculations, we propose that the phosphorus atoms are displaced from their lattice sites by Ge interstitials that are generated during SiGe oxidation. The phosphorus atoms then migrate toward the SiGe–SiO 2 interface through a novel mechanism of hopping between Ge sites as P–Ge split interstitials. Once they reach the interface, they are electrically inactive, potentially in the form of interstitial clusters or as part of the reconstructed interface or oxide.

Thornton, Chappel S.↗
NASA NTRS1992

Coherent-backscatter effect - A vector formulation accounting for polarization and absorption effects and small or large scatterers

Previous theoretical work on the coherent-backscatter effect in the context of speckle time autocorrelation has gone beyond the diffusion approximation and the assumption of isotropic (point) scatterers. This paper extends the theory to include the effects of polarization and absorption, and to give the angular line shape. The results are expressions for angular variations valid for small and large scatterers and linear and circular polarizations, in lossless or lossy media. Calculations show that multiple anisotropic scattering results in the preservation of incident polarization. Application to a problem in radar astronomy is considered. It is shown that the unusual radar measurements (high reflectivity and polarization ratios) of Jupiter's icy Galilean satellites can be explained by coherent backscatter from anisotropic (forward) scatterers.

Peters, Kenneth J.↗
NASA NTRS1972

A two component model of the diurnal variations in the thermospheric composition

A self-consistent, two-dimensional, two-component diffusion model is presented to describe the diurnal component of thermosphere dynamics. In the regions where oxygen and helium are the minor constituents, diffusion is shown to increase the amplitudes of these constituents and to advance the times of their diurnal maxima by several hours with respect to the gas temperature and the major species. Both effects are in basic agreement with satellite observations. The diffusion process is relatively insignificant for temperature, total mass density, and wind fields. The magnitude of the temperature-density phase delay is discussed with respect to its dependence on the electron density distribution.

Mayr, H. G.↗
NASA NTRS2003

Effect of Gravity Level on the Particle Shape and Size During Zeolite Crystal Growth

A microscopic diffusion model is developed to represent solute transport in the boundary layer of a growing zeolite crystal. This model is used to describe the effect of gravity on particle shape and solute distribution. Particle dynamics and crystal growth kinetics serve as the boundary conditions of flow and convection-diffusion equations. A statistical rate theory is used to obtain the rate of solute transport across the growing interface, which is expressed in terms of concentration and velocity of solute species. Microgravity can significantly decrease the solute velocity across the growing interface compared to its earth-based counterpart. The extent of this reduction highly depends on solute diffusion constant in solution. Under gravity, the flow towards the crystal enhances solute transport rate across the growing interface while the flow away from crystals reduces this rate, suggesting a non-uniform growth rate and thus an elliptic final shape. However, microgravity can significantly reduce the influence of flow and obtain a final product with perfect spherical shape. The model predictions compare favorably with the data of space experiment of zeolites grown in space.

Song, Hong-Wei↗
DOE OSTI2022

Heat conduction in an irregular magnetic field. Part 2. Heat transport as a measure of the effective non-integrable volume

Given the large anisotropy of transport processes in magnetized plasmas, the magnetic field structure can strongly impact heat diffusion: magnetic surfaces and cantori form barriers to transport while chaotic layers and island structures can degrade confinement. When a small but non-zero amount of perpendicular diffusion is included, the structure of the magnetic field becomes less important, allowing pressure gradients to be supported across chaotic regions and island chains. We introduce a metric for the effective volume over which the local parallel diffusion dominates based on the solution to the anisotropic heat diffusion equation. To validate this metric, we consider model fields with a single island chain and a strongly chaotic layer for which analytic predictions of the relative parallel and perpendicular transport can be made. We also analyse critically chaotic fields produced from different sets of perturbations, highlighting the impact of the mode number spectrum on the heat transport. Our results indicate that this metric coincides with the effective volume of non-integrability in the limit $\kappa _{\perp } \rightarrow 0$ , where $\kappa_{\perp}$ is the perpendicular diffusion coefficient. We propose that this metric be used to assess the impact of non-integrability on the heat transport in stellarator equilibria.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

First-principles calculations for understanding microstructures and mechanical properties of co-sputtered Al alloys

Recent experimental studies show that co-sputtering solutes with Al, together, can refine columnar grain size around few tens of nanometers and promote the formation and enhance the stability of planar defects such as stacking faults (SFs) and grain boundaries (GBs) in Al alloys. These crystal defects and fine columnar grains result in high strength, enhanced strain hardening and thermal stability of Al alloys. Using first-principles density-functional theory (DFT) calculations, we studied the role of eleven solutes in tailoring kinetics and energetics of adatoms and clusters on Al {111} surface, stable and unstable stacking fault energies, and kinetic energy barriers for the migration of defects. The calculations show that most solutes can effectively refine columnar grain size by decreasing the diffusivity of adatoms and surface clusters. These solutes do not necessarily decrease the stacking fault energy of Al alloys, but reduce the formation energy of faulted surface clusters and increase the energy barriers for the recovery of faulted surface clusters. Correspondingly, the formation of SFs is kinetically promoted during sputtering. Furthermore, solutes are segregated into the core of Shockley partial dislocations and play a pinning effect on SFs, SF arrays and twin boundaries, enhancing the thermal stability of these crystal defects. These findings provide insights into the design of high-strength Al alloys for high-temperature applications.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Laboratory scaled simulation of lidar cloud sounding experiments

The results of lidar measurements carried out on laboratory scale models of clouds are presented. Measurements on laboratory scale models are important since one has the knowledge of the relevant parameters of the diffusing medium, such as: scattering and absorption coefficients, phase function, homogeneity, shape, etc. Knowledge of these parameters enables one to use the results to test the reliability of theoretical and numerical investigations. To obtain a laboratory scaled model of a lidar system sounding a cloud, it is necessary to scale down all the geometrical quantities by the same factor to reduce distances of the order of kilometers to the order of meters, keeping the size and the optical depth of the diffusers unchanged. If a time resolution of the order of nanoseconds is necessary for a lidar sounding actual clouds, the corresponding time resolution for the laboratory model should be of the order of picoseconds. It is possible to obtain this resolution by using picosecond laser systems and fast electrooptical detectors like the streak camera. The results of the laboratory measurements showed that the multiple scattering effect strongly depends on the size of the diffusers, as well as on the concentration. The experimental results were compared with the numerical results of a Monte Carlo code. A generally good agreement was obtained.

Zaccanti, G.↗
NASA NTRS1978

Effects of fabrication and joining processes on compressive strength of boron/aluminum and borsic/aluminum structural panels

Processes for forming and joining boron/aluminum and borsic/aluminum to themselves and to titanium alloys were studied. Composite skin and titanium skin panels were joined to composite stringers by high strength bolts, by spotwelding, by diffusion bonding, by adhesive bonding, or by brazing. The effects of the fabrication and joining processes on panel compressive strengths were discussed. Predicted buckling loads were compared with experimental data.

Royster, D. M.↗
DOE OSTI2022

Optimizing the Orientation of Solar Photovoltaic Systems Considering the Effects of Irradiation and Cell Temperature Models with Dust Accumulation

To cope with the growing installation capacities of solar photovoltaic (PV) systems in desert areas, it is necessary to revisit the energy production models and the optimal angles of PV panels given the significant impacts of ambient temperature, wind speed, dust accumulation, and cleaning frequency. In this study, these four factors are examined for four PV technologies (polycrystalline, microcrystalline, monocrystalline, and thin-film) at three cities in Jordan, Egypt, and Tunisia using precise ground-level meteo-solar measurements. Different models are compared to estimate the diffuse irradiance, as well as account for the effects of operating temperature, wind speed, and dust accumulation on energy production and optimal tilt and azimuth angles of the panels. The results reveal 1.5 % higher energy production estimates using the isotropic model, compared to the anisotropic model in the summer months. Considering the cooling effect of wind speed decreases the operating cell temperature drops by up to 7.05 % for thin film panels. The annually produced energy decreases by 24 % when the panels are cleaned bi-monthly. When the dust accumulation rate doubles, the energy production decreases by ~10 % for all studied cases. Also, the variations in optimal tilt and azimuth angles with dust accumulation rate are within ~3.0 degrees .

14 SOLAR ENERGY↗
NASA NTRS1977

Elevated-temperature flow strength, creep resistance and diffusion welding characteristics of Ti-gAl-2Nb-1Ta-0.8Mo

A study of the flow strength, creep resistance and diffusion welding characteristics of the titanium alloy Ti-6Al-2Nb-1Ta-0.8Mo was conducted. Two mill-processed forms of this alloy were examined. The forged material was essentially processed above the beta transus while the rolled form was subjected to considerable work below the beta transus. Between 1150 and 1250 K, the forged material was stronger and more creep resistant than the rolled alloy. Both forms exhibit superplastic characteristics in this temperature range. Strain measurements during diffusion welding experiments at 1200 K reveal that weld interfaces have no measurable effect on the overall creep deformation. Significant deformation appears to be necessary to produce a quality diffusion weld between superplastic materials. A 'soft' interlayer inserted between faying surfaces would seemingly allow manufacture of quality diffusion welds with little overall deformation.

Whittenberger, J. D.↗
NASA NTRS1979

Elevated temperature flow strength, creep resistance and diffusion welding characteristics of Ti-6Al-2Nb-1Ta-0.8Mo

A study of the flow strength, creep resistance and diffusion welding characteristics of the titanium alloy Ti-6Al-2Nb-1Ta-0.8Mo has been conducted. Two mill-processed forms of this alloy were examined. The forged material had been processed above the beta transus (approximately 1275 K) while the rolled form had been subjected to work below the beta transus. Between 1150 and 1250 K, the forged material was stronger and more creep resistant than the rolled alloy. Both forms exhibit superplastic characteristics in this temperature range. Strain measurements during diffusion welding experiments at 1200 K reveal that weld interfaces have no measurable effect on the overall creep deformation. Significant deformation appears to be necessary to produce a quality diffusion weld between superplastic materials. A 'soft' interlayer inserted between faying surfaces would seemingly allow manufacture of quality diffusion welds with little overall deformation.

Whittenberger, J. D.↗
NASA NTRS2017

High Temperature Characteristics of Pt/TaSi2/Pt/W and Pt/Ti/W Diffusion Barrier Systems for Ohmic Contacts to 4H-SiC

The degradation of ohmic contacts to 4H-SiC pressure sensors over time at high temperature is primarily due to two failure mechanisms: migrating bond pad Au and atmospheric O toward the ohmic contact SiC interface and the inter-metallic mixing between diffusion barrier systems (DBS) and the underlying ohmic contact metallization. We investigated the effectiveness of Pt/TaSi2/Pt/W (DBS-A) and Pt/Ti/W (DBS-B) in preventing Au and O diffusion through the underlying binary Ti/W or alloyed W50:Ni50 ohmic contacts to 4H-SiC and the DBS ohmic contact intermixing at temperature up to 700 C.

Platinum↗
NASA NTRS2000

Photochemistry Saturn's Atmosphere: Effects of an Influx of External Oxygen - 2

We use a one-dimensional diurnally averaged model of photochemistry and diffusion in Saturn's stratosphere to investigate the influence of extraplanetary debris on atmospheric chemistry. In particular, we consider the effects of an influx of oxygen from micrometeoroid ablation or from ring-particle diffusion; the contribution from cometary impacts, satellite debris, or ring vapor is deemed to be less important. The photochemical model results are compared directly with Infrared Space Observatory (ISO) observations to constrain the influx of extraplanetary oxygen to Saturn. From the ISO observations, we determine that the column densities of CO2 and H2O above 10 mbar in Saturn's atmosphere are (6.3 +/- 1) x 10(exp 14) and (1.4 +/- 0.4) x 10(exp 15)/ square cm, respectively; our models indicate that a globally averaged oxygen influx of (4+/-2) x 10(exp 6) O atoms /sq cm/s is required to explain these observations. Models with a locally enhanced influx of H20 operating over a small fraction of the projected area do not provide as good a fit to the ISO H2O observations. If volatile oxygen compounds comprise one-third to one-half of the exogenic source by mass, then Saturn is currently being bombarded with (3 +/- 2) x 10(exp -16) g/square cm/s of extraplanetary material. To reproduce the observed CO2/H2O ratio in Saturn's stratosphere, some of the exogenic oxygen must arrive in the form of a carbon-oxygen bonded species such as CO or CO2. An influx consistent with the composition of cometary ices fails to reproduce the high observed CO2/H2O ratio, suggesting that (i) the material has ices that are slightly more carbon-rich than is typical for comets, (ii) a contribution from an organic-rich component is required, or (iii) some of the hydrogen-oxygen bonded material is converted to carbon-oxygen bonded material without photochemistry (e.g., during the ablation process). We have also reanalyzed the 5-micron CO observations of Noll and Larson and determine that the CO lines are most sensitive to the 100- to 400-mbar column density for which we derive a range of (0.7-1.5) x 10(exp 17)/square cm; the CO observations do not allow us to distinguish between an external or internal source of CO on Saturn. If we assume that all the extraplanetary oxygen derives from a micrometeoroid source, then the unfocused dust flux at 9.5 AU must be (i) (1 +/- 0.7) x 10(exp -16) g/square cm/s if interstellar grains are the source of the external oxygen on Saturn, (ii) (4 +/- 3) x 10 (exp -17) g/ sq. cm./s if IDPs on randomly inclined, highly eccentric orbits (e.g., Halley-type comet grains) are the source of the external oxygen, or (iii) (2+/- 1.4) x 10(exp -18)/g/sq cm/s if IDPs on low inclination, low eccentricity orbits (e.g., Kuiper-belt grains) are the source of the external oxygen. These estimates can be used in combination with future Cassini dust detection data to determine the ultimate source of the dust at Saturn's distance from the Sun.

Moses, Julianne I.↗
NASA NTRS1973

A two-component model of the diurnal variations in the thermospheric composition.

A self consistent two-component diffusion model is presented to describe the diurnal component of the thermosphere dynamics. In the regions where oxygen and helium are the minor constituents the diffusion process is shown to increase significantly the amplitudes of these constituents and to advance the times of their diurnal maxima by several hours with respect to the gas temperature and to the major species. Both effects are in basic agreement with satellite observations. The diffusion process is however relatively insignificant for temperature, total mass density and wind fields.

Mayr, H. G.↗