Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aircraft structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,747 records · Page 97

Two simplified procedures for predicting cyclic material response from a strain history

Simplified inelastic analysis procedures were developed at NASA Lewis and Pratt & Whitney Aircraft for predicting the stress-strain response at the critical location of a thermomechanically cycled structure. These procedures are intended primarily for use as economical structural analysis tools in the early design stages of aircraft engine hot section components where nonlinear finite-element analyses would be prohibitively expensive. Both simplified methods use as input the total strain history calculated from a linear elastic analysis. The elastic results are modified to approximate the characteristics of the inelastic cycle by incremental solution techniques. A von Mises yield criterion is used to determine the onset of active plasticity. The fundamental assumption of these methods is that the inelastic strain is local and constrained from redistribution by the surrounding elastic material.

Kaufman, A.↗

Progressive Damage and Failure Analysis of Bonded Composite Joints at High Energy Dynamic Impacts

Both wing and fuselage structures utilize bonded composite joints for structural efficiency in modern commercial and military aircraft. To ensure compliance with certification requirements mechanical fasteners are typically used as a failsafe mechanism for appropriate strength in the event of complete stiffener disbond. However, the use of fasteners decreases the structural efficiency of the structure by adding weight. This establishes the requirement to better exploit the efficiency of bonded structures and fully understand the failure behavior of adhesively bonded composite structures, particularly when subjected to elevated loading rates due to high energy dynamic impacts (HEDI). For this reason, the NASA Advanced Composite Consortium (ACC) HEDI team developed an experimentation and numerical modeling program for high rate loading of composite joints. In the present work, the response of adhesively bonded composite joints subjected to elevated loading rates is studied numerically and validated against experimental results. Due to dynamic considerations of experiments, the idea of wedge insert was extended to use with Split Hopkinson Pressure Bar (SHPB) testing techniques. Mode-I and Mode-II test configurations were simulated to evaluate the capability of two continuum damage material (CDM) models in LS-DYNA, namely MAT162 and MAT261. Three different levels of fidelity were considered to investigate the level of detail required to numerically predict the failure behavior and the results from high fidelity analysis are presented.

MAT261↗

A Comparison of Metallic, Composite and Nanocomposite Optimal Transonic Transport Wings

Current and future composite material technologies have the potential to greatly improve the performance of large transport aircraft. However, the coupling between aerodynamics and structures makes it challenging to design optimal flexible wings, and the transonic flight regime requires high fidelity computational models. We address these challenges by solving a series of high-fidelity aerostructural optimization problems that explore the design space for the wing of a large transport aircraft. We consider three different materials: aluminum, carbon-fiber reinforced composites and an hypothetical composite based on carbon nanotubes. The design variables consist of both aerodynamic shape (including span), structural sizing, and ply angle fractions in the case of composites. Pareto fronts with respect to structural weight and fuel burn are generated. The wing performance in each case is optimized subject to stress and buckling constraints. We found that composite wings consistently resulted in lower fuel burn and lower structural weight, and that the carbon nanotube composite did not yield the increase in performance one would expect from a material with such outstanding properties. This indicates that there might be diminishing returns when it comes to the application of advanced materials to wing design, requiring further investigation.

Kennedy, Graeme J.↗

Computer control for automated flight test maneuvering

The application of an experimental flight test maneuver autopilot test technique for collecting aerodynamic and structural flight research data on a highly maneuverable aircraft is described in this paper. This technique, which was developed to increase the quality and quantity of data obtained during flight test, was applied to the highly maneuverable aircraft technology (HiMAT) vehicle. A primary flight experiment was to verify the design techniques used to develop the HiMAT aerodynamics and structures. This required the performance of maneuvers for collection of large quantities of high-quality pressure distribution, loads, and wing and canard deflection data. Flight data obtained while executing these research maneuvers are presented to demonstrate the effectiveness of this new technique.

Duke, E. L.↗

Aerogel Hybrid Composite Materials: Designs and Testing for Multifunctional Applications

This webinar will introduce the broad spectrum of aerogel composites and their diverse performance properties such as reduced heat transfer to energy storage, and expands specifically on the aerogel/fiber laminate systems and testing methodologies. The multi-functional laminate composite system, AeroFiber, and its construction is designed by varying the type of fiber (e.g. polyester, carbon, Kevlar®, Spectra® or Innegral(TradeMark) and combinations thereof), the aerogel panel type and thickness, and overall layup configuration. The combination and design of materials may be customized and tailored to achieve a range of desired properties in the resulting laminate system. Multi-functional properties include structural strength, impact resistance, reduction in heat transfer, increased fire resistance, mechanical energy absorption, and acoustic energy dampening. Applications include aerospace, aircraft, automotive, boating, building and construction, lightweight portable structures, liquefied natural gas, cryogenics, transportation and energy, sporting equipment, and military protective gear industries.

Hybrid↗

A framework for the identification of full-field structural dynamics using sequences of images in the presence of non-ideal operating conditions

Recent developments in the ability to automatically and efficiently extract natural frequencies, damping ratios, and full-field mode shapes from video of vibrating structures has great potential for reducing the resources and time required for performing experimental and operational modal analysis at very high spatial resolution. Furthermore, these techniques have the added advantage that they can be implemented remotely and in a non-contact fashion. Emerging full-field imaging techniques therefore have potential to allow the identification of the modal properties of structures in regimes that used to be challenging. For instance, these techniques suggest that the high spatial resolution structural identification could be performed on an aircraft during flight using a ground or aircraft-based imager. They also have the potential to identify the dynamics of microscopic systems. In order to realize this capability it will be necessary to develop techniques that can extract full-field structural dynamics in the presence of non-ideal operating conditions. In this work, we develop a framework for the deployment of emerging algorithms that allow the automatic extraction of high-resolution, full-field modal parameters in the presence of non-ideal operating conditions. One of the most notable non-ideal operating conditions is the rigid body motion of both the structure being measured as well as the imager performing the measurement. We demonstrate an instantiation of the framework by showing how it can be used to address, in-plane, translational, rigid body motion. The development of a frame-to-frame keypoint–based technique for identifying full-field structural dynamics in the presence of either rigid body motion is presented and demonstrated in the context of the framework for the deployment of full-field structural identification techniques in the presence of non-ideal operating conditions. It is expected that this framework will ultimately help enable the collection of full-field structural dynamics using measurement platforms including unmanned aerial vehicles, robotic telescopes, satellites, imagers mounted in high-vibration environments (seismic, industrial, harsh weather), characterization of microscopic structures, and human-carried imagers. If imager-based structural identification techniques mature to the point that they can be used in non-ideal field conditions, it could open up the possibility that the structural health monitoring community will be able to think beyond monitoring individual structures, to full-field structural integrity monitoring at the city scale.

Dasari, Sudeep↗

On the inviscid rolled-up structure of lift generated vortices

A simple form is presented of the relationships for the inviscid, fully developed structure of lift-generated vortices behind aircraft wings. The method is then extended to arbitrary span-load distributions by inferring guidelines for the selection of rollup centers for the vortex sheet, along with rules for calculating the fully developed structure of the resulting multiple vortices. These techniques yield realistic estimates of the rolled-up structure of vortices produced by a wider variety of span-load distributions than possible with the original form of the theory.

Rossow, V. J.↗

Solid State Energy Harvesting and Power Conversion in Gas Turbine Engines

Overview: Solid state energy harvesting using waste heat available in gas turbine engine offers potential for power generation to meet growing power needs of aircraft; Thermoelectric material advances offer new opportunities; Weight-optimized integrated turbine engine structure incorporating energy conversion devices.

aircraft↗

Extension of HCDstruct for Transonic Aeroservoelastic Analysis of Unconventional Aircraft Concepts

A substantial effort has been made to implement an enhanced aerodynamic modeling capability in the Higher-fidelity Conceptual Design and structural optimization tool. This additional capability is needed for a rapid, physics-based method of modeling advanced aircraft concepts at risk of structural failure due to dynamic aeroelastic instabilities. To adequately predict these instabilities, in particular for transonic applications, a generalized aerodynamic matching algorithm was implemented to correct the doublet-lattice model available in Nastran using solution data from a priori computational fluid dynamics anal- ysis. This new capability is demonstrated for two tube-and-wing aircraft configurations, including a Boeing 737-200 for implementation validation and the NASA D8 as a first use case. Results validate the current implementation of the aerodynamic matching utility and demonstrate the importance of using such a method for aircraft configurations featuring fuselage-wing aerodynamic interaction.

Quinlan, Jesse R.↗

Aeroelastic Optimization of Generalized Tube and Wing Aircraft Concepts Using HCDstruct Version 2.0

Major enhancements were made to the Higher-fidelity Conceptual Design and structural optimization (HCDstruct) tool developed at NASA Langley Research Center (LaRC). Whereas previous versions were limited to hybrid wing body (HWB) configurations, the current version of HCDstruct now supports the analysis of generalized tube and wing (TW) aircraft concepts. Along with significantly enhanced user input options for all air- craft configurations, these enhancements represent HCDstruct version 2.0. Validation was performed using a Boeing 737-200 aircraft model, for which primary structure weight estimates agreed well with available data. Additionally, preliminary analysis of the NASA D8 (ND8) aircraft concept was performed, highlighting several new features of the tool.

Quinlan, Jesse R.↗

Experimental study using nearfield acoustic holography of sound transmission through fuselage sidewall structures

The reduction of cabin noise in lightweight, propeller-driven aircraft is an especially difficult problem in noise control. Nearfield Acoustic Holography (NAH) was used to determine the mode of vibration and acoustic intensity for panels which differed in: construction (number of stiffening ribs, size of stifening ribs, construction material, and panel surface curvature); boundary support condition (free edge condition or clamped edge condition); and mode of excitation (structural-borne forces or airborne forces). The different samples of aircraft panels are described and the measurement of the natural response frequencies was discussed under various boundary support and excitation conditions. The results of the NAH measurements are presented.

Maynard, J. D.↗

Flight Test Results on the Stability and Control of the F-15B Quiet Spike Aircraft

The Quiet Spike (QS) flight research program was an aerodynamic and structural proof-of-concept of a telescoping sonic-boom suppressing nose boom on an F-15 B aircraft. The program goal was to collect flight data for model validation up to 1.8 Mach. The primary test philosophy was maintaining safety of flight. In the area of stability and controls the primary concerns were to assess the potential destabilizing effect of the spike on the stability, controllability, and handling qualities of the aircraft and to ensure adequate stability margins across the entire QS flight envelop. This paper reports on the stability and control methods used for flight envelope clearance and flight test results of the F-15B Quiet Spike. Also discussed are the flight test approach, the criteria to proceed to the next flight condition, brief pilot commentary on typical piloting tasks, approach and landing, and refueling task, and air data sensitivity to the flight control system.

Moua, Cheng↗

Study of fuel systems for LH2-fueled subsonic transport aircraft, volume 1

Several engine concepts examined to determine a preferred design which most effectively exploits the characteristics of hydrogen fuel in aircraft tanks received major emphasis. Many candidate designs of tank structure and cryogenic insulation systems were evaluated. Designs of all major elements of the aircraft fuel system including pumps, lines, valves, regulators, and heat exchangers received attention. Selected designs of boost pumps to be mounted in the LH2 tanks, and of a high pressure pump to be mounted on the engine were defined. A final design of LH2-fueled transport aircraft was established which incorporates a preferred design of fuel system. That aircraft was then compared with a conventionally fueled counterpart designed to equivalent technology standards.

Brewer, G. D.↗

A Data System for a Rapid Evaluation Class of Subscale Aerial Vehicle

A low cost, rapid evaluation, test aircraft is used to develop and test airframe damage diagnosis algorithms at Langley Research Center as part of NASA's Aviation Safety Program. The remotely operated subscale aircraft is instrumented with sensors to monitor structural response during flight. Data is collected for good and compromised airframe configurations to develop data driven models for diagnosing airframe state. This paper describes the data acquisition system (DAS) of the rapid evaluation test aircraft. A PC/104 form factor DAS was developed to allow use of Matlab, Simulink simulation code in Langley's existing subscale aircraft flight test infrastructure. The small scale of the test aircraft permitted laboratory testing of the actual flight article under controlled conditions. The low cost and modularity of the DAS permitted adaptation to various flight experiment requirements.

Hogge, Edward F.↗

Wind tunnel investigations of forebody strakes for yaw control on F/A-18 model at subsonic and transonic speeds

Wind tunnel investigations have been conducted of forebody strakes for yaw control on 0.06-scale models of the F/A-18 aircraft at free-stream Mach numbers of 0.20 to 0.90. The testing was conducted in the 7- by 10-Foot Transonic Tunnel at the David Taylor Research Center and the Langley 7- by 10-Foot High-Speed Tunnel. The principal objectives of the testing were to determine the effects of the Mach number and the strake plan form on the strake yaw control effectiveness and the corresponding strake vortex induced flow field. The wind tunnel model configurations simulated an actuated conformal strake deployed for maximum yaw control at high angles of attack. The test data included six-component forces and moments on the complete model, surface static pressure distributions on the forebody and wing leading-edge extensions, and on-surface and off-surface flow visualizations. The results from these studies show that the strake produces large yaw control increments at high angles of attack that exceed the effect of conventional rudders at low angles of attack. The strake yaw control increments diminish with increasing Mach number but continue to exceed the effect of rudder deflection at angles of attack greater than 30 degrees. The character of the strake vortex induced flow field is similar at subsonic and transonic speeds. Cropping the strake planform to account for geometric and structural constraints on the F-18 aircraft has a small effect on the yaw control increments at subsonic speeds and no effect at transonic speeds.

Erickson, Gary E.↗

Impact fracture of composite sandwich structures

An experimental investigation of impact-initiated failures in high-strength graphite/epoxy and Kevlar-49/epoxy sandwich structures has been conducted. The tests consisted of firing small diameter aluminum projectiles with a velocity range of 16-67 meters/second (52-220 ft/sec) at preloaded sandwich specimens. These tests were intended to be representative of service conditions on materials and structures which might be used as secondary aircraft components. The preload and impact energy necessary to initiate catastrophic failure were determined. The residual strength of impact-damaged specimens was also measured. The results of these tests indicate that catastrophic failures in sandwich structures can be initiated at relatively low preloads by impact projectiles at energy levels well below that required to initiate visible damage.

Rhodes, M. D.↗

Extensional collapse modes of structural members

Attenuation of the load transmitted to a vehicle occupant by the structure, either by modifying structural assembly, changing geometry of its elements, or adding specific load limiting devices to help dissipate kinetic energy was studied. General aviation aircraft have fuselage subfloors of a built up structure which are generally very stiff perpendicular to the floor of the cabin. The subfloor structure, designed to crush at an appropriate force level, can be used to advantage in a crash by dissipating energy through plastic buckling of the floor beams and frames. Simple closed form solutions to predict the mean crushing force levels of subfloor designs is useful in engineering practice. The crushing process of thin walled, plate formed, open structures with particular emphasis on L and cruciform shapes was analyzed. Lower and upper bound solutions for the mean crushing strength of cruciforms are obtained by considering modes of deformation which account for both bending and extensional deformation. It is the importance of extensional deformation to the energy absorption process, representing at least one third of the dissipated energy is shown.

Hayduk, R. J.↗

The application and results of a new flight test technique

The application of a flight test maneuver auto-pilot test technique for collecting aerodynamic and structural flight research data on a highly maneuverable aircraft is described. This newly developed flight test technique was applied at the Dryden Flight Research Facility of the NASA Ames Research Center on the highly maneuverable aircraft technology (HiMAT) vehicle. A primary flight experiment was done to verify the design techniques used to develop the HiMAT aerodynamics and structures. This required the collection of large quantities of high-quality pressure distribution, loads, and deflection data. The effectiveness of the flight test technique is illustrated with a flight test example comparing various pressure distribution measurements.

Duke, E. L.↗