Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind tunnel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Analysis and test evaluation of the dynamic response and stability of three advanced turboprop models at low forward speed

Results of wind tunnel tests at low forward speed for blade dynamic response and stability of three 62.2 cm (24.5 in) diameter models of the Prop-Fan, advanced turboprop, are presented. Measurements of dynamic response were made with the rotors mounted on an isolated nacelle, with varying tilt for nonuniform inflow. Low speed stall flutter tests were conducted at Mach numbers from 0.0 to 0.35. Measurements are compared to Eigen-solution flutter boundaries. Calculated 1P stress response agrees favorably with experiment. Predicted stall flutter boundaries correlate well with measured high stress regions. Stall flutter is significantly reduced by increased blade sweep. Susceptibility to stall flutter decreases rapidly with forward speed.

Smith, Arthur F.↗
NASA NTRS2000

Test-to-Test Repeatability of Results From a Subsonic Wing-Body Configuration in the National Transonic Facility

Results from three wind tunnel tests in the National Transonic Facility of a model of an advanced-technology, subsonic-transport wing-body configuration have been analyzed to assess the test-to-test repeatability of several aerodynamic parameters. The scatter, as measured by the prediction interval, in the longitudinal force and moment coefficients increases as the Mach number increases. Residual errors with and without the ESP tubes installed suggest a bias leading to lower drag with the tubes installed. Residual errors as well as average values of the longitudinal force and moment coefficients show that there are small bias errors between the different tests.

Mineck, Raymond E.↗
NASA NTRS1970

Stability and control derivatives of the lifting body vehicles

Predictions of the flight characteristics of lifting bodies have been based almost exclusively on wind-tunnel data for small-scale models. A need thus exists to compare the results from small-scale and full-scale wind-tunnel tests with results from flight tests to establish some measure of the accuracy of the predictions and to assess the sensitivity of the vehicle's handling qualities to typical discrepancies between flight and wind-tunnel results. Comparisons of these types have been one of the primary objectives of the M2-F2, HL-10, and X-24A flight programs. In this paper the more important longitudinal and lateral-directional aerodynamic stability and control derivatives obtained from flight are compared with small- and full-scale wind-tunnel results where applicable. Significant trends and important differences are pointed out, and the implications discussed.

Robert W Kempel↗
NASA NTRS1992

A hypersonic shock tunnel test of the Aeroassist Flight Experiment (AFE) vehicle at high altitude test conditions

The Aeroassist Flight Experiment (AFE) vehicle is a 4.26 m-diameter raked and blunted elliptic cone that is intended to obtain aerodynamic and aerothermodynamic data on blunt bodies at velocities near 10 km/s and altitudes above 75 km. Previous wind tunnel tests of this configuration have been at Mach numbers of 10 or lower. The present test program consisted of five test conditions at Mach numbers between 15 and 20 and simulated altitudes from 75 km to 97 km. Static longitudinal aerodynamic coefficients, the lift-to-drag ratio, and the trim angle-of-attack were obtained for angles-of-attack between 7 deg and 27 deg. The effects of angle-of-attack and shock Reynolds number, Re2, have been studied. These results indicate the AFE configuration is longitudinally stable. The variation of normal force slope, CNalpha and lift-to-drag slope, (L/D)alpha as well as the trim angle-of-attack with Re2 are documented. The trim angle-of-attack increases with decreasing values of shock Reynolds number (increasing altitude) while the lift-to-drag ratio at the trimmed conditions is relatively constant.

Wittliff, C. E.↗
NASA NTRS1977

The panel on propulsion aerodynamics

Sources of discrepancies noted between propulsion aerodynamic characteristics as predicted from wind tunnel tests and as measured in flight are discussed. The variable Reynolds capability of the National Transonic Facility will provide a tool for understanding and quantifying uncertainties involved in extrapolating the corrected wind tunnel data from tunnel conditions to full scale flight conditions.

Bowditch, D.↗
DOE OSTI2022

Instrumentation development and testing of a wind turbine blade for sub-scale wake studies

Wind turbine blade aerodynamics and the resulting wake flow are complex, and wind tunnel testing of these flows can provide critical insight. The data from such tests are also valuable for validation of numerical models. For experiments using sub-scale turbines to be useful, the blade aerodynamics and wakes must exhibit the important features observed in utility-scale turbine flows. In this work, ~1 m blades designed to produce physics relevant to larger scale turbines were manufactured and affixed to an existing turbine. One of the blades was instrumented for blade surface pressure measurements. Time-dependent surface pressure measurements coupled with instantaneous measurements of the inflow with Cobra probes and the wake with particle image velocimetry allowed for characterization of the inflow, blade flow, and near wake. The results demonstrate that the instrumentation was effective in characterizing the blade loading and the flow field. For the one test case discussed in this paper, the measurements of inflow, blade loading, and wake properties facilitate understanding of the wake's behavior.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1975

Results of tests on a Rockwell International space shuttle orbiter (-139 configuration) 0.0175-scale model (no. 29-0) in AEDC tunnel B to determine boundary layer characteristics

Results of wind tunnel tests were conducted to determine boundary layer characteristics on the lower surface of a space shuttle orbiter. Total pressure and temperature profile data at various model stations were obtained using a movable, four-degree-of-freedom probe mechanism and static pressure taps on the model surface. During a typical run, the probe was located over a preselected model location, then driven down through the bondary layer until contact was made with the model surface.

Quan, M.↗
NASA NTRS1992

Sonic boom predictions using a modified Euler code

The environmental impact of a next generation fleet of high-speed civil transports (HSCT) is of great concern in the evaluation of the commercial development of such a transport. One of the potential environmental impacts of a high speed civilian transport is the sonic boom generated by the aircraft and its effects on the population, wildlife, and structures in the vicinity of its flight path. If an HSCT aircraft is restricted from flying overland routes due to excessive booms, the commercial feasibility of such a venture may be questionable. NASA has taken the lead in evaluating and resolving the issues surrounding the development of a high speed civilian transport through its High-Speed Research Program (HSRP). The present paper discusses the usage of a Computational Fluid Dynamics (CFD) nonlinear code in predicting the pressure signature and ultimately the sonic boom generated by a high speed civilian transport. NASA had designed, built, and wind tunnel tested two low boom configurations for flight at Mach 2 and Mach 3. Experimental data was taken at several distances from these models up to a body length from the axis of the aircraft. The near field experimental data serves as a test bed for computational fluid dynamic codes in evaluating their accuracy and reliability for predicting the behavior of future HSCT designs. Sonic boom prediction methodology exists which is based on modified linear theory. These methods can be used reliably if near field signatures are available at distances from the aircraft where nonlinear and three dimensional effects have diminished in importance. Up to the present time, the only reliable method to obtain this data was via the wind tunnel with costly model construction and testing. It is the intent of the present paper to apply a modified three dimensional Euler code to predict the near field signatures of the two low boom configurations recently tested by NASA.

Siclari, Michael J.↗
NASA NTRS1991

In-flight flow visualization characteristics of the NASA F-18 high alpha research vehicle at high angles of attack

Surface and off-surface flow visualization techniques were used to visualize the 3-D separated flows on the NASA F-18 high alpha research vehicle at high angles of attack. Results near the alpha = 25 to 26 deg and alpha = 45 to 49 deg are presented. Both the forebody and leading edge extension (LEX) vortex cores and breakdown locations were visualized using smoke. Forebody and LEX vortex separation lines on the surface were defined using an emitted fluid technique. A laminar separation bubble was also detected on the nose cone using the emitted fluid technique and was similar to that observed in the wind tunnel test, but not as extensive. Regions of attached, separated, and vortical flow were noted on the wing and the leading edge flap using tufts and flow cones, and compared well with limited wind tunnel results.

Fisher, David F.↗
NASA NTRS1940

Full-Scale Tests of Several Propellers Equipped with Spinners, Cuffs, Airfoil and Round Shanks, and NACA 16-Series Sections, Special Report

Wind-tunnel tests of several propeller, cuff, and spinner combinations were conducted in the 20 foot propeller-research tunnel. Three propellers, which ranged in diameter from 8.4 to 11.25 feet, were tested at the front end of a streamline body incorporating spinners of two diameters. The tests covered a blade angle range from 20 deg to 65 deg. The effect of spinner diameter and propeller cuffs on the characteristics of one propeller was determined. Test were also conducted using a propeller which incorporated aerodynamically good shank sections and using one which incorporated the NACA 16 series sections for the outer 20 percent of the blades. Compressibility effects were not measured, owing to the low testing speeds. The results indicated that a conventional propeller was slightly more efficient when tested in conjunction with a 28 inch diameter spinner than with a 23 inch spinner, and that cuffs increased the efficiency as well as the power absorption characteristics. A propeller having good aerodynamic shanks was found to be definitely superior from the efficiency standpoint to a conventional round-shank propeller with or without cuffs; this propeller would probably be considered structurally impracticable, however. The propeller incorporating the NACA 16 series sections at the tims were found to have a slightly higher efficiency than a conventional propeller; the take-off characteristics appeared to be equally good. The effects noted above probably would be accentuated at helical speeds at which compressibility effects would enter.

Biermann, David↗
NASA NTRS2010

RCC Plug Repair Thermal Tools for Shuttle Mission Support

A thermal math model for the Space Shuttle Reinforced Carbon-Carbon (RCC) Plug Repair was developed to increase the confidence in the repair entry performance and provide a real-time mission support tool. The thermal response of the plug cover plate, local RCC, and metallic attach hardware can be assessed with this model for any location on the wing leading edge. The geometry and spatial location of the thermal mesh also matches the structural mesh which allows for the direct mapping of temperature loads and computation of the thermoelastic stresses. The thermal model was correlated to a full scale plug repair radiant test. To utilize the thermal model for flight analyses, accurate predictions of protuberance heating were required. Wind tunnel testing was performed at CUBRC to characterize the heat flux in both the radial and angular directions. Due to the complexity of the implementation of the protuberance heating, an intermediate program was developed to output the heating per nodal location for all OML surfaces in SINDA format. Three Design Reference Cases (DRC) were evaluated with the correlated plug thermal math model to bound the environments which the plug repair would potentially be used.

Rodriguez, Alvaro C.↗
NASA NTRS2009

Findings from the Supersonic Qualification Program of the Mars Science Laboratory Parachute System

In 2012, the Mars Science Laboratory Mission (MSL) will deploy NASA's largest extra-terrestrial parachute, a technology integral to the safe landing of its advanced robotic explorer on the surface. The supersonic parachute system is a mortar deployed 21.5 m disk-gap-band (DGB) parachute, identical in geometric scaling to the Viking era DGB parachutes of the 1970's. The MSL parachute deployment conditions are Mach 2.3 at a dynamic pressure of 750 Pa. The Viking Balloon Launched Decelerator Test (BLDT) successfully demonstrated a maximum of 700 Pa at Mach 2.2 for a 16.1 m DGB parachute in its AV4 flight. All previous Mars deployments have derived their supersonic qualification from the Viking BLDT test series, preventing the need for full scale high altitude supersonic testing. The qualification programs for Mars Pathfinder, Mars Exploration Rover, and Phoenix Scout Missions were all limited to subsonic structural qualification, with supersonic performance and survivability bounded by the BLDT qualification. The MSL parachute, at the edge of the supersonic heritage deployment space and 33% larger than the Viking parachute, accepts a certain degree of risk without addressing the supersonic environment in which it will deploy. In addition, MSL will spend up to 10 seconds above Mach 1.5, an aerodynamic regime that is associated with a known parachute instability characterized by significant canopy projected area fluctuation and dynamic drag variation. This aerodynamic instability, referred to as "area oscillations" by the parachute community has drag performance, inflation stability, and structural implications, introducing risk to mission success if not quantified for the MSL parachute system. To minimize this risk and as an alternative to a prohibitively expensive high altitude test program, a multi-phase qualification program using computation simulation validated by subscale test was developed and implemented for MSL. The first phase consisted of 2% of fullscale supersonic wind tunnel testing of a rigid DGB parachute with entry-vehicle to validate two high fidelity computational fluid dynamics (CFD) tools. The computer codes utilized Large Eddy Simulation and Detached Eddy Simulation numerical approaches to accurately capture the turbulent wake of the entry vehicle and its coupling to the parachute bow-shock. The second phase was the development of fluid structure interaction (FSI) computational tools to predict parachute response to the supersonic flow field. The FSI development included the integration of the CFD from the first phase with a finite element structural model of the parachute membrane and cable elements. In this phase, a 4% of full-scale supersonic flexible parachute test program was conducted to provide validation data to the FSI code and an empirical dataset of the MSL parachute in a flight-like environment. The final phase is FSI simulations of the full-scale MSL parachute in a Mars type deployment. Findings from this program will be presented in terms of code development and validation, empirical findings from the supersonic testing, and drag performance during supersonic operation.

EDL↗
NASA NTRS1975

Results of tests of a Rockwell International space shuttle orbiter (-139 configuration) 0.0175-scale model (no. 29-0) in AEDC tunnel F to determine hypersonic heating effects (OH11)

Results from wind tunnel tests to determine hypersonic aerodynamic heating rates on a NASA/Rockwell Space Shuttle Orbiter are reported. The tests were to determine Mach number effects, if any, and to obtain overall heating rate data at high Mach numbers from 10.5 to 16. The model used was a 0.0175-scale model built to Rockwell Orbiter lines VL70-000139. The model identity number is 29-0. These tests, designated OH11, were conducted in the AEDC Tunnel F.

Quan, M.↗
NASA NTRS1983

Plume base flow simulation technology

A combined analytical/empirical approach was studied in an effort to define the plume simulation parameters for base flow. For design purposes, rocket exhaust simulation (i.e., plume simulation) is determined by wind tunnel testing. Cold gas testing was concluded to be a cost and schedule effective data base of substantial scope. The results fell short of the target, although work conducted was conclusive and advanced the state of the art. Comparisons of wind tunnel predictions with Space Transportation System (STS) flight data showed considerable differences. However, a review of the technology program data base has yielded an additional parameter that may correlate flight and cold gas test data. Data from the plume technology program and the NASA test flights are presented to substantiate the proposed simulation parameters.

Roberts, B. B.↗