Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Oscillator strengths of the Si II 181 nanometer resonance multiplet

We report Si II experimental log (gf)-values of -2.38(4) for the 180.801 nm line, of -2.18(4) for the 181.693 nm line, and of -3.29(5) for the 181.745 nm line, where the number in parentheses is the uncertainty in the last digit. The overall uncertainties (about 10 percent) include the 1 sigma random uncertainty (about 6 percent) and an estimate of the systematic uncertainty. The oscillator strengths are determined by combining branching fractions and radiative lifetimes. The branching fractions are measured using standard spectroradiometry on an optically thin source; the radiative lifetimes are measured using time-resolved laser-induced fluorescence.

Bergeson, S. D.↗
NASA NTRS1921

Crippling Strength of Axially Loaded Rods

A new empirical formula was developed that holds good for any length and any material of a rod, and agrees well with the results of extensive strength tests. To facilitate calculations, three tables are included, giving the crippling load for solid and hollow sectioned wooden rods of different thickness and length, as well as for steel tubes manufactured according to the standards of Army Air Services Inspection. Further, a graphical method of calculation of the breaking load is derived in which a single curve is employed for determination of the allowable fiber stress. Finally, the theory is discussed of the elastic curve for a rod subject to compression, according to which no deflection occurs, and the apparent contradiction of this conclusion by test results is attributed to the fact that the rods under test are not perfectly straight, or that the wall thickness and the material are not uniform. Under the assumption of an eccentric rod having a slight initial bend according to a sine curve, a simple formula for the deflection is derived, which shows a surprising agreement with test results. From this a further formula is derived for the determination of the allowable load on an eccentric rod. The resulting relations are made clearer by means of a graphical representation of the relation of the moments of the outer and inner forces to the deflection.

Natalis, FR↗
NASA NTRS1932

The compressive strength of duralumin columns of equal angle section

This report presents a chart giving the compressive strength of duralumin columns of equal angle section. The data used in the construction of the chart were obtained from various published sources and were correlated with theory in the range where secondary failure occurred. Appendices are included giving excerpts from Army and Navy specifications for duralumin and approximate formulas for the properties of the equal angle section.

Lundquist, Eugene E↗
NASA NTRS1933

Mercerization of Cotton for Strength with Special Reference to Aircraft Cloth

The object of the present investigation was to determine the conditions for mercerizing cotton yarn to obtain the maximum strength for a given weight. Apparatus for controlling the variables was built and yarns were mercerized with it under systematically varied conditions of tension, time, temperature, and concentration of caustic soda. The strongest conclusion to be drawn from this work is that the strongest mercerized yarn of a given count from a given quality of cotton is obtained under the following conditions: 1. use of low-twist yarn obtained with twist multipliers from 2.2 to 3; 2. thorough pretreatment of the yarn to remove all extraneous materials; 3. mercerization at a temperature of 0 C or lower; 4. use of sufficient tension during mercerization to prevent the yarn from contracting more than 3 percent. 5. Use of caustic solution having a concentration of 10 percent or higher; 6. the time of mercerization to be 5 minutes. The resulting yarn should be 40 to 100 percent stronger than the original yarn of the same weight.

Wilkie, J B↗
NASA NTRS1937

Increasing the Strength of Aluminum-alloy Columns by Prestressing

A series of tests was made in which the column strength of 17ST tubing was increased as much as 50 percent by prestressing the tubing to 40,000 pounds per square inch in compression under conditions of support that prevented column failure at this stress. This prestressing achieves it's beneficial effects entirely by improving the compressive properties of the material, principally the proportional limit.

Holt, M↗
NASA NTRS1942

Strength tests of thin-walled elliptic duralumin cylinders in pure bending and in combined pure bending and torsion

An analysis is presented of the results of tests made by the Massachusetts Institute of Technology and by the National Advisory Committee for Aeronautics on an investigation of the strength of thin-walled circular and elliptic cylinders in pure bending and in combined torsion and bending. In each of the loading conditions, the bending moments were applied in the plane of the major axis of the ellipse.

Lundquist, Eugene E↗
NASA NTRS1940

Analysis of Cylinder-pressure-indicator Diagrams Showing Effects of Mixture Strength and Spark Timing

An investigation was made to determine the effect of mixture strength and of normal as well as optimum spark timing on the combustion, on the cylinder temperature, and on the performance characteristics of an engine. A single-cylinder test unit utilizing an air-cooled cylinder and a carburetor and operating with gasoline having an octane rating of 92 was used. The investigation covered a range of fuel-air ratios from 0.053 to 0.118. Indicator diagrams and engine-performance data were taken for each change in engine conditions. Examination of the indicator shows that for fuel-air ratios less than and greater than 0.082 the rate and the amount of effective fuel burned decreased. For a fuel-air ratio of 0.118 the combustion efficiency was only 58 percent. Advancing the spark timing increased the rate of pressure rise. This effect was more pronounced with leaner mixtures.

Gerrish, Harold C↗
NASA NTRS1946

Effect of Brake Forming on the Strength of 24S-T Aluminum-alloy Sheet

Tests were made to determine the effect of brake forming on the strength of 24S-T aluminum alloy sheet that had been formed to an inside bend radius of three times the sheet thickness. The results for both directions of the grain of the material showed that the compressive yield stresses were appreciably increased, that the tensile yield stresses were moderately increased, that the ultimate tensile stresses were only slightly increased, that the elongations were considerably reduced, and that the shapes of the tensile and compressive stress-strain curves were markedly changed.

Heimerl, George J↗
NASA NTRS1956

Experimental Investigation of the Strength of Multiweb Beams with Corrugated Webs

The results of an experimental investigation of the strength of multiweb beams with corrugated webs are reported. Included in the investigation were two types of connection between the web and the skin. A comparison between the structural efficiency of corrugated-web and channel-web multiweb beams is presented, and it is shown that, for a considerable range of the structural index, corrugated-web beams can be built which are structurally more efficient than channel-web beams.

LOADS AND STRESSES, STRUCTURAL - BENDING↗
NASA NTRS1956

The fatigue strength of riveted joints and lugs

This report deals with a number of tests on riveted joints and lugs for the primary purpose of comparing the several types of riveted joints and to study the effect of various factors on the fatigue strength of lugs. A check was made to ascertain whether or not an estimate of the fatigue life at a certain loading could be made from the dimensions of the joint and the fatigue data of the unnotched materials. Recommendations are made on the proportioning of joints to obtain better fatigue behavior.

Schijve, J↗
NASA NTRS1931

A method of calculating the ultimate strength of continuous beams

The purpose of this study was to investigate the strength of continuous beams after the elastic limit has been passed. As a result, a method of calculation, which is applicable to maximum load conditions, has been developed. The method is simpler than the methods now in use and it applies properly to conditions where the present methods fail to apply.

Newlin, J A↗
NASA NTRS1934

Strength Tests of Thin-Walled Duralumin Cylinders in Compression

This report is the second of a series presenting the results of strength tests of thin-walled duralumin cylinders and truncated cones of circular and elliptic section. It contains the results obtained from compression tests on 45 thin-walled duralumin cylinders of circular section with ends clamped to rigid bulkheads. In addition to the tests on duralumin cylinders, there are included the results of numerous tests on rubber, celluloid, steel, and brass cylinders obtained from various sources.

Lundquist, Eugene E↗
NASA NTRS1937

Strength of Welded Aircraft Joints

This investigation is a continuation of work started in 1928 and described in NACA-TR-348 which shows that the insertion of gusset plates was the most satisfactory way of strengthening a joint. Additional tests of the present series show that joints of this type could be improved by cutting out the portion of the plate between the intersecting tubes. T and lattice joints in thin-walled tubing 1 1/2 by 0.020 inch have somewhat lower strengths than joints in tubing of greater wall thickness because of failure by local buckling. In welding the thin-walled tubing, the recently developed "carburizing flux" process was found to be the only method capable of producing joints free from cracks. The "magnetic powder" inspection was used to detect cracks in the joints and flaws in the tubing.

Brueggeman, W C↗
NASA NTRS1939

The Column Strength of Two Extruded Aluminum-Alloy H-Sections

Extruded aluminum-alloy members of various cross sections are used in aircraft as compression members either singly or as stiffeners for aluminum-alloy sheet. In order to design such members, it is necessary to know their column strength or, in the case of stiffeners, the value of the double modulus, which is best obtained for practical purposes from column tests. Column tests made on two extruded h-sections are described, and column formulas and formulas for the ratio of the double modulus to Young's modulus, based on the tests, are given.

Osgood, William R↗
NASA NTRS1950

Determination of Plate Compressive Strengths at Elevated Temperatures

The results of local-instability tests of h-section plate assemblies and compressive stress-strain tests of extruded 75s-t6 aluminum alloy, obtained to determine flat-plate compressive strength under stabilized elevated temperature conditions, are given for temperatures up to 600 degrees F. The results show that methods available for calculating the critical compressive stress at room temperature can also be used at elevated temperatures if the applicable compressive stress-strain curve for the material is given.

Heimerl, George J↗
NASA NTRS1942

Strength Tests on Hulls and Floats

The present report deals with strength tests on hulls and floats intended in part for the collection of construction data for the design of these components and in part for the stress analysis of the finished hulls and floats.

Matthaes, K↗