Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “recent availability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

THE SPATIALLY RESOLVED STAR FORMATION LAW FROM INTEGRAL FIELD SPECTROSCOPY: VIRUS-P OBSERVATIONS OF NGC 5194

We investigate the relation between the star formation rate (SFR) surface density (SIGMA{sub SFR}) and the mass surface density of gas (SIGMA{sub gas}) in NGC 5194 (a.k.a. M51a, Whirlpool Galaxy). Visible Integral field Replicable Unit Spectrograph Prototype (VIRUS-P) integral field spectroscopy of the central 4.1 x 4.1 kpc{sup 2} of the galaxy is used to measure Halpha, Hbeta, [O III]lambda5007, [N II]lambdalambda6548,6584, and [S II]lambdalambda6717,6731 emission line fluxes for 735 regions approx170 pc in diameter. We use the Balmer decrement to calculate nebular dust extinctions, and correct the observed fluxes in order to accurately measure SIGMA{sub SFR} in each region. Archival H I 21 cm and CO maps with spatial resolution similar to that of VIRUS-P are used to measure the atomic and molecular gas surface density for each region. We present a new method for fitting the star formation law (SFL), which includes the intrinsic scatter in the relation as a free parameter, allows the inclusion of non-detections in both SIGMA{sub gas} and SIGMA{sub SFR}, and is free of the systematics involved in performing linear regressions over incomplete data in logarithmic space. After rejecting regions whose nebular spectrum is affected by the central active galactic nucleus in NGC 5194, we use the [S II]/Halpha ratio to separate spectroscopically the contribution from the diffuse ionized gas (DIG) in the galaxy, which has a different temperature and ionization state from those of H II regions in the disk. The DIG only accounts for 11% of the total Halpha luminosity integrated over the whole central region, but on local scales it can account for up to a 100% of the Halpha emission, especially in the inter-arm regions. After removing the DIG contribution from the Halpha fluxes, we measure a slope N = 0.82 +- 0.05, and an intrinsic scatter epsilon = 0.43 +- 0.02 dex for the molecular gas SFL. We also measure a typical depletion timescale tau=SIGMA{sub H{sub i+H{sub 2}}}/SIGMA{sub SFR}approx2 Gyr, in good agreement with recent measurements by Bigiel et al. The atomic gas density shows no correlation with the SFR, and the total gas SFL in the sampled density range closely follows the molecular gas SFL. Integral field spectroscopy allows a much cleaner measurement of Halpha emission line fluxes than narrow-band imaging, since it is free of the systematics introduced by continuum subtraction, underlying photospheric absorption, and contamination by the [N II] doublet. We assess the validity of different corrections usually applied in narrow-band measurements to overcome these issues and find that while systematics are introduced by these corrections, they are only dominant in the low surface brightness regime. The disagreement with the previous measurement of a super-linear molecular SFL by Kennicutt et al. is most likely due to differences in the fitting method. Our results support the recent evidence for a low, and close to constant, star formation efficiency (SFE =tau{sup -1}) in the molecular component of the interstellar medium. The data show an excellent agreement with the recently proposed model of the SFL by Krumholz et al. The large intrinsic scatter observed may imply the existence of other parameters, beyond the availability of gas, which are important in setting the SFR.

79 ASTRONOMY AND ASTROPHYSICS↗

Ionization of highly charged relativistic ions by neutral atoms and ions

Ionization of highly charged relativistic ions by neutral atoms and ions is considered. Numerical results of recently developed computer codes based on the plane-wave Born and the equivalent-photon approximations are presented and compared with experimental data available at relativistic energies for 1s electron ionization. New formulas for relativistic cross sections are derived for ionization of the projectile electron with arbitrary quantum numbers n and l. The results are obtained on the basis of the nonrelativistic reduction in the Dirac matrix element.

74 ATOMIC AND MOLECULAR PHYSICS↗

Bayesian inference of nuclear symmetry energy from measured and imagined neutron skin thickness in Sn 116 , 118 , 120 , 122 , 124 , 130 , 132 , Pb 208 , and Ca 48

The neutron skin thickness Δr np in heavy nuclei has been known as one of the most sensitive terrestrial probes of the nuclear symmetry energy E sym (ρ) around $\frac{2}{3}$ of the saturation density ρ 0 of nuclear matter. Existing neutron skin data mostly from hadronic observables suffer from large uncertainties and their extraction from experiments are often strongly model dependent. While waiting eagerly for the promised model-independent and high-precision neutron skin data for 208 Pb and 48 Ca from the parity-violating electron scattering experiments (PREX-II and CREX at JLab as well as MREX at MESA), within the Bayesian statistical framework using the Skyrme-Hartree-Fock model we infer the posterior probability distribution functions (PDFs) of the slope parameter L of the nuclear symmetry energy at ρ 0 from imagined Δr np ( 208 Pb)=0.15, 0.20, and 0.30 fm with a 1σ error bar of 0.02, 0.04, and 0.06 fm, respectively, as well as Δr np ( 48 Ca)=0.12, 0.15, and 0.25 fm, with different 1σ error bar of 0.01 and 0.02 fm, respectively. The results are compared with the PDFs of L inferred using the same approach from the available Δr np data for 116, 118, 120, 122, 124, 130, 132 Sn from hadronic probes. They are also compared with results from a recent Bayesian analysis of the radius and tidal deformability data of canonical neutron stars from GW170817 and NICER. The neutron skin data for Sn isotopes gives L = 45.5 $^{+ 26.5}_{-21.6}$ MeV surrounding its mean value or L = 53 . 4 $^{+ 18.6}_{ -29.5}$ MeV surrounding its maximum a posteriori value, respectively, with the latter smaller than but consistent with the L = 66 $^{+ 12}_{-20}$ MeV from the neutron star data within their 68% confidence intervals. We found that Δr np = 0.17 –0.18 fm in 208 Pb with an error bar of about 0.02 fm leads to a PDF of L compatible with that from analyzing the Sn data. To provide additionally useful information on L extracted from the Δr np of Sn isotopes, the experimental error bar of Δr np in 208 Pb should be at least smaller than 0.06 fm aimed by some current experiments. In addition, the Δr np ( 48 Ca) needs to be larger than 0.15 fm but smaller than 0.25 fm to be compatible with the Sn and/or neutron star results. To further improve our current knowledge about L and distinguish its PDFs in the examples considered, even higher precisions leading to significantly less than ±20 MeV error bars for L at 68% confidence level are necessary.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Model calculations of the Sivers function satisfying the Burkardt sum rule

It is shown that, at variance with previous analyses, the MIT bag model can explain the available data of the Sivers function and satisfies the Burkardt sum rule to a few percent accuracy. The agreement is similar to the one recently found in the constituent quark model. Therefore, these two model calculations of the Sivers function are in agreement with the present experimental and theoretical wisdom.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Enhanced in-pile instrumentation at the advanced test reactor

Many of the sensors deployed at materials and test reactors cannot withstand the high flux/high temperature test conditions often requested by users at U.S. test reactors, such as the Advanced Test Reactor (ATR) at the Idaho National Laboratory. To address this issue, an instrumentation development effort was initiated as part of the ATR National Scientific User Facility in 2007 to support the development and deployment of enhanced in-pile sensors. This paper reports results from this effort. Specifically, this paper identifies the types of sensors currently available to support in-pile irradiations and those sensors currently available to ATR users. Accomplishments from new sensor technology deployment efforts are highlighted by describing new temperature and thermal conductivity sensors now available to ATR users. Efforts to deploy enhanced in-pile sensors for detecting elongation and realtime flux detectors are also reported, and recently-initiated research to evaluate the viability of advanced technologies to provide enhanced accuracy for measuring key parameters during irradiation testing are noted. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

CMIP5 Scientific Gaps and Recommendations for CMIP6

The Coupled Model Intercomparison Project (CMIP) is an ongoing coordinated international activity of numerical experimentation of unprecedented scope and impact on climate science. Its most recent phase, the fifth phase (CMIP5), has created nearly 2 PB of output from dozens of experiments performed by dozens of comprehensive climate models available to the climate science research community. In so doing, it has greatly advanced climate science. While CMIP5 has given answers to important science questions, with the help of a community survey we identify and motivate three broad topics here that guided the scientific framework of the next phase of CMIP, that is, CMIP6: (1) How does the Earth system respond to changes in forcing? (2) What are the origins and consequences of systematic model biases? (3) How can we assess future climate changes given internal climate variability, predictability, and uncertainties in scenarios? CMIP has demonstrated the power of idealized experiments to better understand how the climate system works. We expect that these idealized approaches will continue to contribute to CMIP6. The quantification of radiative forcings and responses was poor, and thus it requires new methods and experiments to address this gap. There are a number of systematic model biases that appear in all phases of CMIP that remain a major climate modeling challenge. In conclusion, these biases need increased attention to better understand their origins and consequences through targeted experiments. Improving understanding of the mechanisms’ underlying internal climate variability for more skillful decadal climate predictions and long-term projections remains another challenge for CMIP6.

58 GEOSCIENCES↗

Costa - Introduction to 2015 Annual Report

In parallel with Sandia National Laboratories having two major locations (NM and CA), along with a number of smaller facilities across the nation, so too is the distribution of scientific, engineering and computing resources. As a part of Sandia’s Institutional Computing Program, CA site-based Sandia computer scientists and engineers have been providing mission and research staff with local CA resident expertise on computing options while also focusing on two growing high performance computing research problems. The first is how to increase system resilience to failure, as machines grow larger, more complex and heterogeneous. The second is how to ensure that computer hardware and configurations are optimized for specialized data analytical mission needs within the overall Sandia computing environment, including the HPC subenvironment. All of these activities support the larger Sandia effort in accelerating development and integration of high performance computing into national security missions. Sandia continues to both promote national R&D objectives, including the recent Presidential Executive Order establishing the National Strategic Computing Initiative and work to ensure that the full range of computing services and capabilities are available for all mission responsibilities, from national security to energy to homeland defense.

97 MATHEMATICS AND COMPUTING↗

Evaluation of Technetium Getters to Improve the Performance of Cast Stone

Cast Stone has been selected as the preferred waste form for solidification of aqueous secondary liquid effluents from the Hanford Tank Waste Treatment and Immobilization Plant (WTP) process condensates and low-activity waste (LAW) melter off-gas caustic scrubber effluents. Cast Stone is also being evaluated as a supplemental immobilization technology to provide the necessary LAW treatment capacity to complete the Hanford tank waste cleanup mission in a timely and cost effective manner. One of the major radionuclides that Cast Stone has the potential to immobilize is technetium (Tc). The mechanism for immobilization is through the reduction of the highly mobile Tc(VII) species to the less mobile Tc(IV) species by the blast furnace slag (BFS) used in the Cast Stone formulation. Technetium immobilization through this method would be beneficial because Tc is one of the most difficult contaminants to address at the U.S. Department of Energy (DOE) Hanford Site due to its complex chemical behavior in tank waste, limited incorporation in mid- to high-temperature immobilization processes (vitrification, steam reformation, etc.), and high mobility in subsurface environments. In fact, the Tank Closure and Waste Management Environmental Impact Statement for the Hanford Site, Richland, Washington (TC&WM EIS) identifies technetium-99 ( 99 Tc) as one of the radioactive tank waste components contributing the most to the environmental impact associated with the cleanup of the Hanford Site. The TC&WM EIS, along with an earlier supplemental waste-form risk assessment, used a diffusion-limited release model to estimate the release of different contaminants from the WTP process waste forms. In both of these predictive modeling exercises, where effective diffusivities based on grout performance data available at the time, groundwater at the 100-m down-gradient well exceeded the allowable maximum permissible concentrations for 99 Tc. (900 pCi/L). Recent relatively short-term (63 day) leach tests conducted on both LAW and secondary waste Cast Stone monoliths indicated that 99 Tc diffusivities were at or near diffusivities where the groundwater at the 100-m down-gradient well would exceed the allowable maximum permissible 99 Tc concentrations. There is, therefore, a need and an opportunity to improve the retention of Tc in the Cast Stone waste form. One method to improve the performance of the Cast Stone waste form is through the addition of “getters” that selectively sequester Tc inside Cast Stone.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Parallel-In-Time For Moving Meshes

With steadily growing computational resources available, scientists must develop e ective ways to utilize the increased resources. High performance, highly parallel software has be- come a standard. However until recent years parallelism has focused primarily on the spatial domain. When solving a space-time partial di erential equation (PDE), this leads to a sequential bottleneck in the temporal dimension, particularly when taking a large number of time steps. The XBraid parallel-in-time library was developed as a practical way to add temporal parallelism to existing se- quential codes with only minor modi cations. In this work, a rezoning-type moving mesh is applied to a di usion problem and formulated in a parallel-in-time framework. Tests and scaling studies are run using XBraid and demonstrate excellent results for the simple model problem considered herein.

97 MATHEMATICS AND COMPUTING↗

Recent Progress in Electron Scattering at SLAC

Since the last meeting in this conference series in Paris in 1981, there has been major progress in electron scattering at SLAC on several fronts. A new experiment on ep elastic scattering at large momentum transfer, Experiment El36, has recently completed data taking. A new measurement of deep inelastic electron scattering from nuclear targets, Experiment El39, has been completed and preliminary results are available. A new program of experiments has begun, called Nuclear Physics at SLAC (NPAS), that will use a new injector on the SLAC linac to provide high intensity beams in the energy range from 0.5 to 6 GeV.

43 PARTICLE ACCELERATORS↗

Symmetry Engineering of Topological Quantum States (Final Report)

Recent discoveries of topological materials have generated immense interest. The electronic states of these materials have unique topological properties protected by specific symmetries that generate exotic quantum phenomena and technologically useful properties. In topological semimetals, topological phase transitions caused by symmetry-breaking have long been known to be possible, but experimental verification has been impeded by the fact that for most materials, symmetry is a fixed property of the crystal, not an easily tunable parameter. The objectives of the proposed work are (i) to reveal the intimate connection between symmetry and topological electronic states, and (ii) to produce several tunable topological quantum phases which are of both scientific and technological significance. This project focuses on the recently discovered layered topological semimetals WHM (W = Zr or rare earth elements; H = Si, Sn, Sb; M = S, Se, Te). The layered crystal structure, availability of atomically thin two-dimensional (2D) flakes, and rich magnetic states of WHM compounds allow for symmetry engineering via synergistic bulk- and nano-approaches. The PIs plan to modify the crystal symmetry in a controllable manner using strain, and break time-reversal symmetry using magnetic WHMs and via magnetic proximity in heterostructures. This research is based on the combined efforts of bulk single crystal growth, nanodevice fabrication, strain application, theoretical calculations, and quantum transport measurements.

36 MATERIALS SCIENCE↗

A Supply Chain Road Map for Offshore Wind Energy in the United States

"A Supply Chain Road Map for Offshore Wind Energy in the United States" identifies pathways to developing a domestic offshore wind supply chain that can manufacture and deploy the major components needed to set the United States on a pathway to installing 30 GW of offshore wind by 2030 and 110 GW by 2050. The report estimates that this supply chain could require an investment of at least $\$$22.7 billion this decade to meet an annual demand for components, ports, and vessels in 2030. Although this is a considerable investment, it could allow the industry to install around $\$$100 billion worth of offshore wind this decade by reducing risk of delays due to global supply chain bottlenecks and creating a robust network of assets that will continue to be effective well beyond 2030. The United States would need at least 34 manufacturing facilities employing 10,000 workers, 39,000 jobs in the supporting supply chain, 10 marshaling ports, 4-6 dedicated wind turbine installation vessels, 4-6 dedicated heavy-lift vessels, and 4-8 U.S.-flagged specialized feeder barges to come online this decade to support an average annual deployment of 4-6 gigawatts offshore wind capacity per year. This supply chain could be developed in 6-9 years, but would require near-term decision making and efficient permitting and planning to strategically develop these resources by 2030. Additional investment and expansion would be required in the 2030s as the sector expands into new regions (such as the Gulf of Mexico) and new technologies (such as larger wind turbines and floating wind energy projects). Furthermore, the planning process needs to meaningfully engage with communities that will be impacted by supply chain expansion to achieve just outcomes and maximize benefits to these stakeholders, which will result in a more equitable and sustainable supply chain. While U.S. offshore wind has made significant progress in recent years, remaining supply chain challenges include uncertainty surrounding deployment and procurement timelines; a lack of port and vessel infrastructure; and limitations in the available workforce, supporting supplier networks, and energy justice best practices. However, many of these problems can be addressed through improved communication between key stakeholder groups, support from federal and state governments, and forward-thinking designs of supply chain assets to accommodate future technology changes for fixed-bottom and floating offshore wind. Although it is a significant task, developing these domestic capabilities represents a once-in-a-generation opportunity to contribute to a decarbonized energy future and also create massive economic benefits that are distributed throughout the country.

17 WIND ENERGY↗

Biochemical Conversion of Lignocellulosic Biomass to Hydrocarbon Fuels and Products: 2022 State of Technology and Future Research

The annual State of Technology (SOT) assessment is a key activity for biochemical platform research. It allows the impact of research progress (both directly achieved in-house at the National Renewable Energy Laboratory [NREL] and indirectly extrapolated from available public data) to be quantified in terms of economic improvements in the overall cellulosic biofuel production process for a particular conversion pathway. As such, initial benchmarks can be established for currently demonstrated performance and progress can be tracked toward out-year goals to ultimately demonstrate cost-competitive biofuel technology. Building upon efforts to progress NREL's biochemical platform R&D work toward ultimate 2030 goals to demonstrate less than $2.50/gallon gasoline equivalent (GGE) fuel selling prices, experimental and techno-economic analysis (TEA) activities have primarily focused on "advanced" biochemical processing strategies to fuels and coproducts, guided by TEA modeling to highlight key barriers and priorities toward achieving this goal across a number of potential bioconversion pathways. The purpose of the present effort is to benchmark the latest experimental developments for these pathways as quantified by modeled minimum fuel selling prices (MFSPs), as a measure of current status relative to those final targets. For this SOT, TEA models were run for two separate biological conversion pathways to fuels, based on available data for integrated biomass deconstruction and hydrolysate processing; namely carboxylic acids (primarily butyric acid) and diols (2,3-butanediol [BDO]), reflecting NREL's recently published 2018 biochemical design report focused on those two pathways. The models were run across two scenarios for lignin utilization, namely combustion and conversion to value-added coproducts.

09 BIOMASS FUELS↗

Management and International Sorption Model Collaboration (M4SF-23LL010302062-NEA-TDB)

This progress report (Level 4 Milestone Number M4SF-23LL010302062) summarizes research conducted at Lawrence Livermore National Laboratory (LLNL) within the Crystalline International Collaborations Activity Number SF-23LL01030206. The activity is focused on our long-term commitment of engaging our partners in international nuclear waste repository research. This includes participation in the Nuclear Energy Agency Thermochemical Database (NEA-TDB) Project and development of methodologies for integrating US and international thermodynamic databases for use in SFWST Generic Disposal System Assessment (GDSA) efforts. A continuing focus for FY23 efforts has been to support the US participation in the NEA-TDB effort (Mavrik Zavarin replaced Cindy Atkins-Duffin on the NEA-TDB Management Board (MB) and Executive Group (EG)) and developing mechanisms for integration of NEA-TDB thermochemical data with LLNL’s SUPCRTNE thermodynamic database that supports the SFWST GDSA activities. This effort is coordinated with the Argillite work package SUPCRTNE database development efforts. The goal is to provide a downloadable database that will be hosted on a LLNL website which integrates NEA-TDB data into the LLNL SUPCRTNE database where appropriate. As part of our international activities, we continue our effort to integrate international sorption databases into L-SCIE (Zavarin et al., 2022b). We presented opportunities to include sorption in the next phase of NEA-TDB efforts at the April 2023 EG meeting in Paris. FY23 efforts focused on ensuring interoperable database development across multiple international database development activities. The overall goal is to produce an open source database that can be shared and integrated with multiple nuclear waste programs internationally and harness modern data science workflows and algorithms to incorporate these new approaches into reactive transport and performance assessment models. In collaboration with our Helmholtz Zentrum Dresden Rossendorf partners, we recently demonstrated the power of FAIR open source databases by fitting iron oxide (hydrous ferric oxide, goethite, hematite, and magnetite) protolysis constants to all available L-SCIE data. The results were submitted as a manuscript to J. Colloid Interface Science. This work will inform future metal sorption studies on a variety of iron oxides in order to discern the most appropriate acidity constants and surface complexation modeling constructs to account for pH-dependent mineral surface charge behavior. This work also explored automated surface complexation model development workflows in order to generate higher throughput model input files for a more facile incorporation into GDSA activities.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗