Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxide interfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Nano-engineering of electron correlation in oxide superlattices

Oxide heterostructures and superlattices (SLs) have attracted a great deal of attention in recent years owing to the rich exotic properties encountered at their interfaces. We focus on the potential of tunable correlated oxides by investigating the spectral function of the prototypical correlated metal SrVO3 , using soft x-ray absorption spectroscopy and resonant inelastic soft x-ray scattering to access both unoccupied and occupied electronic states, respectively. We demonstrate a remarkable level of tunability in the spectral function of SrVO 3 by varying its thickness within the SrVO 3 /SrTiO 3 SL, showing that the effects of electron correlation can be tuned from dominating the energy spectrum in a strongly correlated Mott–Hubbard insulator, towards a correlated metal. We show that the effects of dimensionality on the correlated properties of SrVO 3 are augmented by interlayer coupling, yielding a highly flexible correlated oxide that may be readily married with other oxide systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electronic passivation of silicon surfaces by thin films of atomic layer deposited gallium oxide

This paper proposes the application of gallium oxide (Ga{sub 2}O{sub 3}) thin films to crystalline silicon solar cells. Effective passivation of n- and p-type crystalline silicon surfaces has been achieved by the application of very thin Ga{sub 2}O{sub 3} films prepared by atomic layer deposition using trimethylgallium (TMGa) and ozone (O{sub 3}) as the reactants. Surface recombination velocities as low as 6.1 cm/s have been recorded with films less than 4.5 nm thick. A range of deposition parameters has been explored, with growth rates of approximately 0.2 Å/cycle providing optimum passivation. The thermal activation energy for passivation of the Si-Ga{sub 2}O{sub 3} interface has been found to be approximately 0.5 eV. Depassivation of the interface was observed for prolonged annealing at increased temperatures. The activation energy for depassivation was measured to be 1.9 eV.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Short-Term Oxidation Studies on Nicrofer- 6025HT in Air at Elevated Temperatures for Advanced Coal Based Power Plants

Several advanced air separation unit (ASU) designs being considered for use in coal gasification rely on the use of solid state mixed ionic and electronic conductors. Nicrofer-6025HT, a nickel-based alloy, has been identified as a potential manifold material to transport the hot gases into the ASUs. In the current study, isothermal oxidation tests were conducted on Nicrofer-6025HT in the temperature range of 700–900 °C for up to 24 h. The evolution of oxide scale was evaluated using SEM, XRD, and XPS. The composite surface oxide layer that formed consisted of an outer chromia-rich scale and an inner alumina scale. For the longer times at the higher temperatures evaluated, a NiCr2O4 spinel phase was located at the interface between the alumina and chromia. Based on the experimental results a four-step oxidation model was proposed.

Alloy 602CA↗

Perspective—Emergent Phases in Rare Earth Nickelate Heterostructure

The prediction of high T c superconductivity in layers of LaNiO 3 through orbital engineering has led to extensive research efforts over the last fifteen years. During this period, a plethora of thin films and heterostructures based rare-earth nickelate family with perovskite structure has been synthesized and explored. Here, in this short perspective, we briefly review the complexity of bulk RENiO 3 , spotlighting several recent findings of emergent phenomena in heterostructures containing the interface between RENiO 3 and another transition metal oxide. Finally, we outline potentially interesting future directions linked to time-domain dynamics to harness new Mott and topological phases in artificial structures of RENiO 3 .

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Deciphering Interfacial Chemical and Electrochemical Reactions of Sulfide-Based All-Solid-State Batteries

Large interfacial resistance resulting from interfacial reactions is widely acknowledged as one of the main challenges in sulfide electrolytes (SEs)-based all-solid-state lithium batteries (ASSLBs). However, the root cause of the large interfacial resistance between the SEs and typical layered oxide cathodes is not fully understood yet. Here we deciphered that interfacial oxygen loss from single-crystal LiNi 0.5 Mn 0.3 Co 0.2 O 2 (SC-NMC532) chemically oxidizes Li 10 GeP 2 S 12 , generating oxygen-containing interfacial species. Meanwhile, the interfacial oxygen loss also induces a structural change of oxide cathodes (layered-to-rocksalt). Besides, the high operation voltage can electrochemically oxidize SEs to form non-oxygen species (e.g. polysulfides). These chemically and electrochemically oxidized species, together with the interfacial structural change, are responsible for the large interfacial resistance at the cathode interface. More importantly, the widely adopted interfacial coating strategy is effective in suppressing chemically oxidized oxygen-containing species and mitigating the coincident interfacial structural change but is unable to prevent electrochemically induced non-oxygen species. These findings provide a deeper insight into the large interfacial resistance between the typical SE and layered oxide cathodes, which may be of assistance for the rational interface design of SE-based ASSLBs in future.

25 ENERGY STORAGE↗

Fabrication of MgAl{sub 2}O{sub 4} tunnel barrier by radio frequency-sputtering method and magnetoresistance effect through it with Fe or Fe{sub 4}N ferromagnetic electrode

Spinel MgAl{sub 2}O{sub 4} thin films were deposited on MgO single-crystal substrates and epitaxial Fe (or Fe{sub 4}N) thin films by RF-sputtering from a ceramic target. Epitaxial relationship was confirmed by X-ray diffraction analysis between the crystalline spinel MgAl{sub 2}O{sub 4} films and the respective substrate and underlayers, while no diffraction peak was observed from the films deposited on amorphous substrates. Spin-valve type magnetic tunnel junctions (MTJs) with a stacking structure of Fe [Fe{sub 4}N]/MgAl{sub 2}O{sub 4}/CoFeB/Ru/Fe/MnIr exhibited normal [inverse] tunnel magnetoresistance (TMR) effect, reflecting the sign of spin polarization of Fe [Fe{sub 4}N]. The maximum magnitude of the TMR ratio obtained for the Fe-based and Fe{sub 4}N-based MTJs was 67% and 18%, respectively. The resistance area product values of the MTJs were significantly larger than the reported values for the MTJs with a post-oxidized spinel MgAl{sub 2}O{sub 4} barrier.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Quantitative analysis of chemical interaction and doping of the Si(111) native oxide surface with tetrafluorotetracyanoquinodimethane

The charge-transfer states and the carrier concentration of the native oxide Si(111) surface adsorbed with 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F{sub 4}-TCNQ) were investigated by X-ray photoelectron spectroscopy (XPS) and independently driven four-probe electrical conductivity measurements. The XPS results show that F{sub 4}-TCNQ molecules are involved in charge transfer with the SiO{sub 2}/Si(111) surface. The Si 2p XPS spectra and the surface photovoltage shift provide the evidences of (i) change in the oxidation states at the SiO{sub 2}-Si(111) interface region and (ii) formation of a p-type space charge layer (SCL) with a hole concentration of 1.7 × 10{sup 10} cm{sup −2}, respectively. The four-probe I–V measurements also support the formation of the p-type SCL, and the estimated hole concentration of 2.0 × 10{sup 10} cm{sup −2} agrees well with the XPS results. The estimated SCL hole concentrations were much smaller than the excess charge density in the F{sub 4}-TCNQ layer, of the order of 10{sup 13} cm{sup −2}, suggesting that most of charges were localized as the oxidation states at the SiO{sub 2}-Si(111) interface region. The present quantitative methods ensure precise determination of the doping concentration near the surface region.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Impact of metal diffusion, lattice distortions, native defects, and ambient on dielectric breakdown in Ni–Ga 2 O 3 Schottky diodes

Ga 2 O 3 unipolar devices are of high interest due to their ~8 MV/cm predicted breakdown fields, which have not yet been achieved due to premature device failure. Pre- and post-failure defect analysis of Ni–Ga 2 O 3 Schottky diodes in ultrahigh vacuum (UHV) and air were performed using depth-resolved cathodoluminescence, high angle annular dark field scanning transmission electron microscopy, and energy dispersive x-ray analysis to understand the physical mechanisms that precede premature breakdown. The breakdown voltage in UHV was dramatically reduced by nearly 40% compared with the breakdown in air. This reduction in the breakdown voltage correlated with post-breakdown differences in Ni distribution, indicating that the coordination and bonding of Ni contribute strongly to electrical behavior in Ni–Ga 2 O 3 Schottky diodes. Breakdown studies in UHV revealed that Ni diffuses away more from the metal–semiconductor interface than with air breakdown, where Ni localizes more near the interface, indicative of the preferential formation of a Ni oxide under O-poor conditions. These measurements also identified the formation of divacancy-interstitial complexes and their characteristic luminescence signature ~150 nm from the interface, the densities of which correlated with breakdown fields. These findings show that electric-field-induced degradation occurs via the rearrangement of native point defects, which act as an additional precursor to device failure. Macroscopically, they show the impact of both vacuum conditions and metal reactivity on Ga 2 O 3 device fabrication.

36 MATERIALS SCIENCE↗

1.5 MeV proton irradiation effects on electrical and structural properties of TiO{sub 2}/n-Si interface

In this paper, we report the effect of 1.5 MeV proton beam irradiation dose on the structural and electrical properties of TiO{sub 2} thin films deposited on n–Si substrates. The formation and transformation of different TiO{sub 2} phases in the irradiated thin films were characterized by X-ray diffraction and X-ray photoelectron spectroscopy (XPS). X-ray diffraction measurements revealed that the as grown film was rich in Ti{sub 5}O{sub 9} phase and then converted to mixed phases of TiO{sub 2} (rutile and anatase) after exposure with radiation doses up to 5 × 10{sup 14} cm{sup −2}. The XPS results revealed the formation of oxygen vacancy (negative) traps in the exposed TiO{sub 2} films, which showed strong dependence on the dose. The C-V measurements showed that proton radiations also damaged the Si substrate and created deep level defects in the substrate, which caused a shift of 0.26 ± 0.01 V in the flat band voltage (V{sub FB}). I–V measurements showed that the ideality factor increased and the rectification ratio dropped with the increase in the radiation dose. The present study showed the stability of TiO{sub 2}/Si interface and TiO{sub 2} film as an oxide layer against proton radiations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Aqueous Fe(II) on Arsenate Sorption on Goethite and Hematite

Biogeochemical iron cycling often generates systems where aqueous Fe(II) and solid Fe(III) oxides coexist. Reactions between these species result in iron oxide surface and phase transformations, iron isotope fractionation, and redox transformations of many contaminant species. Fe(II)-induced recrystallization of goethite and hematite has recently been shown to cause the repartitioning of Ni(II) at the mineral-water interface, with adsorbed Ni incorporating into the iron oxide structure and preincorporated Ni released back into aqueous solution. However, the effect of Fe(II) on the fate and speciation of redox inactive species incompatible with iron oxide structures is unclear. Arsenate sorption to hematite and goethite in the presence of aqueous Fe(II) was studied to determine whether Fe(II) causes substantial changes in the sorption mechanisms of such incompatible species. Sorption isotherms reveal that Fe(II) minimally alters macroscopic arsenate sorption behavior except at circumneutral pH in the presence of elevated concentrations (10{sup -3} M) of Fe(II) and at high arsenate loadings, where a clear signature of precipitation is observed. Powder X-ray diffraction demonstrates that the ferrous arsenate mineral symplesite precipitates under such conditions. Extended X-ray absorption fine structure spectroscopy shows that outside this precipitation regime arsenate surface complexation mechanisms are unaffected by Fe(II). In addition, arsenate was found to suppress Fe(II) sorption through competitive adsorption processes before the onset of symplesite precipitation. This study demonstrates that the sorption of species incompatible with iron oxide structure is not substantially affected by Fe(II) but that such species may potentially interfere with Fe(II)-iron oxide reactions via competitive adsorption.

54 ENVIRONMENTAL SCIENCES↗

Optical and vibrational properties of (ZnO){sub k} In{sub 2}O{sub 3} natural superlattice nanostructures

A thermodynamically stable series of superlattices, (ZnO){sub k}In{sub 2}O{sub 3}, form in the ZnO-In{sub 2}O{sub 3} binary oxide system for InO{sub 1.5} concentrations from about 13 up to about 33 mole percent (m/o). These natural superlattices, which consist of a periodic stacking of single, two-dimensional sheets of InO{sub 6} octahedra, are found to give rise to systematic changes in the optical and vibrational properties of the superlattices. Low-frequency Raman scattering provides the evidence for the activation of acoustic phonons due to the folding of Brillouin zone. New vibrational modes at 520 and 620 cm{sup −1}, not present in either ZnO or In{sub 2}O{sub 3}, become Raman active. These new modes are attributed to collective plasmon oscillations localized at the two-dimensional InO{sub 1.5} sheets. Infrared reflectivity experiments, and simulations taking into account a negative dielectric susceptibility due to electron carriers in ZnO and interface modes of the dielectric layer of InO{sub 2}, explain the occurrence of these new modes. We postulate that a localized electron gas forms at the ZnO/InO{sub 2} interface due to the electron band alignment and polarization effects. All our observations suggest that there are quantum contributions to the thermal and electrical conductivity in these natural superlattices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Model for thickness dependence of radiation charging in MOS structures

The model considers charge buildup in MOS structures due to hole trapping in the oxide and the creation of sheet charge at the silicon interface. The contribution of hole trapping causes the flatband voltage to increase with thickness in a manner in which square and cube dependences are limiting cases. Experimental measurements on samples covering a 200 - 1000 A range of oxide thickness are consistent with the model, using independently obtained values of hole-trapping parameters. An important finding of our experimental results is that a negative interface charge contribution due to surface states created during irradiation compensates most of the positive charge in the oxide at flatband. The tendency of the surface states to 'track' the positive charge buildup in the oxide, for all thicknesses, applies both in creation during irradiation and in annihilation during annealing. An explanation is proposed based on the common defect origin of hole traps and potential surface states.

Viswanathan, C. R.↗

Electric field enhanced diffusion welding of alloy 617: Microstructural characteristics and mechanical properties

This study investigated the microstructural characteristics and mechanical behavior of diffusion welded nickel-based Alloy 617 obtained by electric field-assisted sintering (EFAS) using various parameters. The interfacial microstructure exhibited different characteristics including good grain boundary (GB) migration across the interface in the samples diffusion-welded at 1100 °C and a flat interface in the samples joined at 1000 °C and 1050 °C. The interface consisted of fine Al 2 O 3 oxides, while precipitation of interfacial M 23 C 6 carbides was not observed. Grain boundaries migrated across the Al 2 O 3 oxides, leaving these oxides within the grains. Graded grain size was observed, with grain coarsening being more significant near the sample surface due to the temperature gradient induced by EFAS. Tensile testing revealed that the specimens fractured in the matrix away from the interface, indicting strong diffusion-welded joints. Further, the peak tensile strength of 807 MPa was obtained in the samples welded at 1000 °C due to minimal grain growth. The materials obtained at 1100 °C exhibited reduced tensile strength but improved ductility. Strain maps revealed by digital image correlation showed alternating high and low strain segments in the samples produced at 1000 °C and 1050 °C, indicating that the flat interfaces with no GB migration were less ductile compared to the matrix. A greater strain uniformity was observed along the bond interfaces with improved GB migration. The hardness reduced near the sample surfaces due to enlarged grains induced by temperature gradient. This study demonstrates that GB migration and enhanced mechanical strength can be achieved in diffusion-welded Alloy 617.

36 MATERIALS SCIENCE↗

Formation of solid thorium monoxide at near-ambient conditions as observed by neutron reflectometry and interpreted by screened hybrid functional calculations

Oxidation of a ~1000 Å sputter-deposited thorium thin film at 150 °C in 100 ppm of flowing oxygen in argon produces the long-sought solid form of thorium monoxide. Changes in the scattering length density (SLD) distribution in the film over the 700-min experiment measured by in-situ, dynamic neutron reflectometry (NR) shows the densities, compositions and thickness of the various thorium oxides layers formed. Screened, hybrid density-functional theory calculations of potential thorium oxides aid interpretation, providing atomic-level picture and energetics for understanding oxygen migration. NR provided evidence of the formation of substoichiometric thorium oxide, ThO y (y < 1) at the interface between the unreacted thorium metal and its dioxide overcoat which grows inward, consuming the thorium at a rate of 2.1 Å/min while y increases until reaching 1:1 oxygen-to-thorium. Its presence indicates that kinetically-favored solid-phase ThO can be preferentially generated as a majority phase under the thermodynamically-favored ThO 2 top layer at conditions close to ambient.

36 MATERIALS SCIENCE↗

Transparent Conducting Oxides as Cathodes in Li-O2 Batteries: A First Principles Computational Investigation

Li-O2 batteries have traditionally used carbon based electrodes (graphite, buckypaper) as the cathode of choice due toits good electrical conductivity, stability against non-aqueous electrolytes like dimethoxyethane (DME) and ease ofhandling. But, the carbon cathode also leads to formation of carbonate by-products that increase overpotentials duringcharging leading to degradation of the cathode and reduction of cyclability. Recent investigations have focused on using metal-oxides like SnO2, TiO2 as viable cathodes-alternatives in Li-O2 systems. In this paper, we investigate transparent conducting oxides (TCOs) as cathodes with focus on the interface between the TCO surfaces and the discharge product, Li2O2, in the Li-O2 battery using first principles computations.

transparent conducting oxides↗

Electrolyte-driven interphase stabilization in high-voltage sodium-ion full cells

Sodium-ion batteries with a high-voltage O3-type layered oxide cathode paired with a hard carbon anode can offer high energy density; however, significant interfacial instabilities driven by electrode/electrolyte reactions limit a broader industrial adoption. Localized high concentration electrolytes (LHCEs) are a rational choice as they promote salt decomposition over solvent, forming stable, inorganic-rich electrode-electrolyte interphases (EEIs). We present here a comparison of high-voltage (4.2 V) hard carbon | NaNi 1/3 Fe 1/3 Mn 1/3 O 2 pouch cells in LHCEs and in a standard carbonate-based electrolyte by (i) examining the influence of diluent choice on the electrochemical performance of LHCEs and (ii) investigating how the electrolyte chemistry affects the composition and structure of EEIs formed. Importantly, LHCEs demonstrate superior electrochemical performance, achieving 37% higher capacity after 200 cycles (119 vs. 87 mA h g -1 ) compared to the carbonate-based electrolyte. The enhanced stabilization provided by LHCEs at the interface with high-voltage sodium layered oxide cathode is revealed by gas evolution measurements obtained through online electrochemical mass spectrometry (OEMS). Time-of-flight secondary ion mass spectrometry paired with focused ion beam and advanced statistical analyses reveal that the superior performance of LHCE stems from a robust, thin cathode electrolyte interphase formed on the sodium layered oxide cathode and a homogeneous solid electrolyte interphase formation on the hard carbon anode. Furthermore, this study highlights the critical importance of electrolyte design in interphase stabilization, which plays a key role in advancing sodium-ion batteries toward commercial viability.

25 ENERGY STORAGE↗

Asphericity Can Cause Nonuniform Lithium Intercalation in Battery Active Particles

Uniform intercalation is desired to enable next-generation Li-ion batteries. While we expect nonuniformity in materials undergoing a phase change, single-phase intercalation materials such as nickel manganese cobalt oxide are believed to lithiate uniformly at the particle/electrolyte interface. However, recent imaging reveals nonuniform lithiation. Motivated by this discrepancy, we examine if aspherical particle shape can cause such nonuniformity since the conventional belief is based on spherical particle theory. We obtain real particle geometries using rapid lab-based X-ray computed tomography and subsequently perform physics-based calculations accounting for electrochemical reactions at the particle/electrolyte interface and lithium transport inside the particle bulk. The aspherical geometry breaks the symmetry and causes nonuniform reaction distribution. Such nonuniformity is exacerbated as the particle becomes more aspherical. We report the proposed mechanism represents a fundamental limit on achievable lithiation uniformity in aspherical particles in the absence of other mechanisms causing inhomogeneity, such as grain structure, nonuniform carbon-binder coating, etc.

25 ENERGY STORAGE↗