SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Mount includes metallic cup and support ring placed in mold fixture. Viscoelastic material is injected between these parts by means of large hypodermic needle. Circular projections on cup and ring extend into material and are kept in place without dependence on quality of adhesion between material and metal.
Theoretical formulation, analysis, and results are presented that are necessary to analyze quadrupole noise generated from a loaded, subsonic rotor because of its interaction with an inflow distortion or inlet turbulence. The ratio of quadrupole to dipole noise is largely a function of the axial Mach number, wheel tip Mach number, rotor solidity, and total pressure ratio across the rotor. It is relatively independent of the specific form of the inflow distortion or inlet turbulence. Comparisons with experimental data only succeed in predicting gross levels at a given speed and fail to predict the variation of noise at fixed speed with flow and pressure ratio. Likely sources of this discrepancy are discussed.
Scientific literature which deals with the study of human behavior and crew interaction in situations simulating long term space flight is summarized and organized. A bibliography of all the pertinent U.S. literature available is included, along with definitions of the behavioral characteristics terms employed. The summarized studies are analyzed according to behavioral factors and environmental conditions. The analysis consist of two matrices. (1) The matrix of factors studied correlates each research study area and individual study with the behavioral factors that were investigated in the study. (2) The matrix of conclusions identifies those studies whose investigators appeared to draw specific conclusions concerning questions of importance to NASA.
A modified high impedance preamplifier circuit which provides outputs to drive an Omega-VLF receiver and an ADF-LF receiver from a common antenna on general aviation aircraft is reported. The preamplifier was evaluated with fixed ground station receivers and results show the burn out problem of the first stage MOSFET during very close lightning discharges was eliminated.
A model is considered of a point source of radiation with a power-law spectrum in which atoms are both accelerated and photoionized by the radiation pressure, and the resulting spectrum of escape velocities is calculated. It is found that the velocity spectrum will depend only on the power-law index and will be independent of the radiation intensity. It is shown that relativistic velocities are not possible for power-law indices typical of astrophysical objects.
Power supply consists of several stages, interconnected and programmed for required output. In capacitor charging mode, transistor switches are closed. Last stage is in series with rectifier that prevents current from flowing backward into circuit. In capacitor discharge mode, transistor switches are closed, and voltage delivered to load is sum of voltages across capacitors.
Plug nozzles with chute-type noise suppressors were tested with and without ejector shrouds at free-stream Mach numbers from 0 to 0.45 and over a range of nozzle pressure ratios from 2 to 4. A 36-chute suppressor nozzle with an ejector had an efficiency of 94.6 percent at an assumed takeoff pressure ratio of 3.0 and a Mach number of 0.36. This represents only a 3.4 percent performance penalty when compared with the 98 percent efficiency obtained with a previously tested unsuppressed plug nozzle.
Techniques were developed that utilize general purpose structural analysis computer programs to generate the equations of motion necessary for limiting performance studies. The methodology necessary to couple available general purpose finite element structural programs to a limiting performance capability was developed. Primary emphasis was given to the use of the general purpose program to develop equations of motion in a form that can be used by the limiting performance program.
A series of two-dimensional plug nozzles was tested with and without ejector shrouds at free stream Mach numbers from 0 to 0.45 and over a range of nozzle pressure ratios from 2 to 4. These nozzles were also tested with and without chute noise suppressors. A two-dimensional plug nozzle has an efficiency of 96.1 percent at an assumed takeoff pressure ratio of 3.0 and Mach 0.36. A 12-chute suppressed nozzle with sidewalls has an efficiency of 81.0 percent (15.1 percent below the unsuppressed nozzle).
Velocity profile measurements are determined on and around a barchan dune model inserted in the roughness layer on the tunnel floor. A theoretical investigation is made into the factors influencing the rate of sand flow around the dune. Flow visualization techniques are employed in the mapping of streamlines of flow on the dune's surface. Maps of erosion and deposition of sand are constructed for the barchan model, utilizing both flow visualization techniques and friction velocities calculated from the measured velocity profiles. The sediment budget found experimentally for the model is compared to predicted and observed results reported. The comparison shows fairly good agreement between the experimentally determined and predicted sediment budgets.
Model information and data obtained from wind tunnel tests performed on a 0.006 scale model of the Rockwell International space shuttle orbiter and external tank in the 18 inch Variable Density Hypersonic Wind Tunnel (VDHT) at NASA Langley Research Center are presented. Tests were performed at a Mach number of 8.0 over a Reynolds Number range from 0.1 to 10.0 million per foot at 0 deg and -5 deg angle of attack and 0 deg sideslip angle. Transition heating rates were determined using thin skin thermocouples located at various locations on the orbiter and ET. The test was conducted in three stages: orbiter plus external tank (mated configuration); orbiter alone, and external tank alone. The effects of boundary layer trips were also included in the test sequence. The plotted results presented show the effect of configuration interference on the orbiter lower surface and on the ET. Tabulated data are given.
Explore the source record for details and available documents.
A model for the prediction of wake-related sound generation by a single airfoil is presented which assumes that the net force fluctuation on an airfoil can be expressed in terms of the net momentum fluctuation in the near wake of the airfoil. The model predicts a forcing function for sound generation which is related to the spectra of the two-point velocity correlations in the turbulent region near the airfoil trailing edge. Cross spectra were obtained from correlations of the longitudinal and transverse components of turbulence in the wake of a 36-in. chord airfoil in a wind tunnel using x-probe hot-wire sensors. Additional data were obtained from a 10-in. chord airfoil in a free-jet facility. Based on results from these tests, a scaling model was developed using the turbulent boundary-layer thickness as the primary length measure. The model was used to predict the sound radiated from a 2-in. chord airfoil for which acoustical data was available; good agreement was obtained both in level and spectral shape. The single-airfoil result is extended to a rotor geometry, and comparisons are studied for various aerodynamic parameters.
The phenomenon of separated flow on a series of circular-arc afterbodies was investigated using the Langley 16-foot transonic tunnel at free-stream Mach numbers from 0.40 to 0.95 at 0 deg angle of attack. Both high-pressure air and solid circular cylinders with a diameter equal to the nozzle exit diameter were used to simulate jet exhausts. A detailed data base of boundary layer separation locations was obtained using oil-flow techniques. The results indicate that boundary layer separation is most extensive on steep boattails at high Mach numbers.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.