SEARCH · Engineering Papers

Results for “coils”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Description of a 2.3 kW power transformer for space applications

The principle features and special testing of a high voltage high power transformer designed and developed for space application are described. The transformer is operated in a series resonant inverter supplying beam power to a 30 cm mercury ion thruster. Electrical requirements include operation of 2.3 kW continuous power output, primary currents to 35 amps rms, and frequencies up to 20 kHz. High efficiency was obtained through detailed considerations of the tradeoffs available in core materials, wire selection, coil configurations and thermal control. A number of novel heat removal techniques are discussed which control the winding temperature using only the available conductive cooling.

Hansen, I.↗

NASA NTRS1979

Test and evaluation of Fern Engineering Company, Incorporated, solar heating and hot water system

Tests, test results, examination and evaluation by Underwriters Laboratory, Inc., of a single family solar heating and hot water system consisting of collector, storage, control, transport, and data acquisition are presented. The structural characteristics of the solar flat plate collectors were evaluated according to snow and wind loads indicated in various building codes to determine their suitability for use both Michigan and Pennsylvania where prototype systems were installed. The flame spread classification of the thermal insulation is discussed and the fire tests conducted on components are described. The operation and dielectrics withstand tests of the energy transport module indicate the module is capable of rated air delivery. Tests of the control panel indicate the relay coil temperatures exceed the temperature limits allowed for the insulating materials involved.

Source record↗

NASA NTRS1979

Solar energy retrofit for Clarksville Middle School, Clarksville, Indiana

The solar energy retrofit heating system installed to provide heating for two gymnasiums at the Clarksville Middle School located in Clarksville, Indiana is described in detail. The system type is hot water using existing chilled water piping and chilled water coils in an air handler system. Flat plate, single-glazed selectively coated solar collectors were installed on the roof of each gymnasium. Total collector area covers 6,520 square feet. The liquid is stored in a 10,000 gallon steel tank installed below grade.

Source record↗

NASA NTRS1977

Mass drivers. 1: Electrical design

A mass driver is an electrical device used to accelerate payloads of any material to a high velocity. Small vehicles (called buckets) containing superconducting coils carry the payloads. These buckets are accelerated by pulsed magnetic fields, timed by information on their position, and are guided by induced magnetic fields set up in a surrounding guideway. Upon reaching the correct velocity, the buckets release their payloads, then they are slowed for recirculation to be reused. A rationale is presented that leads to a relatively simple and near-optimum design, as well as basic programs for calculating acceleration. The transverse oscillation frequencies are found to be invariant to guideway transverse dimensions.

William H. Arnold↗

NASA NTRS1977

Mass drivers. 2: Structural dynamics

Various structural and dynamical problems related to both small-scale forces between the drive coils and within the bucket structure as well as the overall combined large-scale dynamical interaction of the bucket stream and MDRE (Mass Drive Reaction Engine) structure are examined. The large-scale dynamics appear weakly stable. Finally, MDRE operation in an inverse-square-law gravitational field is discussed and the required curved shape of the guideway is computed.

William H. Arnold↗

NASA NTRS1978

NaOH-based high temperature heat-of-fusion thermal energy storage device

A material called Thermkeep, developed as a low-cost method for the storage of thermal energy for solar electric power generating systems is discussed. The storage device consists of an insulated cylinder containing Thermkeep in which coiled tubular heat exchangers are immersed. A one-tenth scale model of the design contains 25 heat-exchanger tubes and 1500 kg of Thermkeep. Its instrumentation includes thermocouples to measure internal Thermkeep temperatures, vessel surface, heated shroud surface, and pressure gauges to indicate heat-exchanger pressure drops. The test-circuit design is presented and experimental results are discussed.

Cohen, B. M.↗

NASA NTRS1978

Cooling radioisotope thermoelectric generators in the Shuttle

Radioisotope thermoelectric generators (RTG) to be used on future spacecraft and launched by the Shuttle must be cooled from the time they are installed and enclosed until the spacecraft is deployed from the Shuttle. A special Cooling Kit maintains their temperature well below critical by circulating water through the coils soldered to them and through a heat exchanger that boils water and externally discharges the resulting steam. The RTG Cooling Kit, including its support frame, if fully charged with about 64 kg of evaporation water, will increase the Shuttle launch mass by about 200 kg.

Norman, R. M.↗

NASA NTRS1978

Continuous extrusion of coal

A feeding method for use with bituminous coals that exhibit plasticity at elevated temperatures is described and demonstrated on a small screw extruder previously used to extrude polyethylene. A metered feed of coal heated to a temperature just below that of incipient caking (approximately 450 C) is used. Modifications to the extruder consisting of ceramic band heaters, auxiliary cooling coils on the thrust bearing and special quick opening dies are detailed. Coals successfully extruded include high volatile A bituminous coals, high volatile B bituminous coals, a high volatile C bituminous coal and a coal with high ash content. The computer program, EXTRUD, used to simulate the extruder is described. Predicted power consumption exhibits 30% scatter, which is explained by the sensitivity of the coal friction coefficient to temperature profiles. Detailed analysis reveals some discrepancies in the program that need to be resolved.

England, C.↗

NASA NTRS1978

Fiber optic rotation sensor /FORS/ laboratory performance evaluation

A single axis rotation sensor, utilizing a 200 m single mode optical fiber in a 30 cm diameter coil has been constructed and tested in the laboratory. A He-Ne laser is the light source for the Sagnac interferometer-mode sensor. The outputs of Si detectors viewing two complementary interference patterns are electronically differenced to obtain a rotation-dependent signal. Linear response over a rotation rate range of about 0.0001 to 0.1 rad/sec was obtained.

Goldstein, R.↗

NASA NTRS1978

An inductively powered telemetry system for temperature, EKG, and activity monitoring

An implant telemetry system for the simultaneous monitoring of temperature, activity, and EKG from small animals, such as rats, has recently been designed with the novel feature that instead of a battery the system is energized by an inductive field. A 250 kHz resonant coil surrounds the cage (30 x 30 x 20 cm) and provides the approximately 100 microwatt of power required to operate the implant transmitter while allowing the animal unrestrained movement in the cage. The implant can also be battery operated if desired. RF transmission is in the 8-10 MHz band, which allows the use of a simple, essentially single IC chip, receiver.

Fryer, T. B.↗

NASA NTRS1979

Beam builder for space fabrication

Construction of a beam builder for producing triangular truss aluminum beams for use on large space structures is described. The machine will fabricate 0.04 cm thick 2024-T3 aluminum alloy into beams weighing 1.265 kg-m with side braces spot-welded to end caps to fabricate a triangular truss configuration up to 305 m long. The design characteristics, the electrical subsystems, the power requirements of the spot welding equipment, and the computer system for coordinating the motion of the Yoder rolling mills for forming caps from aluminum coils are described. Spot welding was compared with ultrasonic welding, stapling, wire stitching, riveting, grommets, stamp-lok, and pierce and fold joining methods with respect to ease of operation, safety, practicality, and ease of energy consumption. The beam builder will be evaluated to identify design requirements which can be utilized for the space flight version of its concept.

Ehl, J. H.↗

NASA NTRS1979

A search for geographic control on the occurrence of magnetospheric ELF emissions

Search coil magnetometer data obtained in the magnetosphere on Ogo 5 and Ogo 6 were studied for evidence of man-induced stimulation of the two dominant electromagnetic emissions, chorus and plasmaspheric hiss. Variability of chorus with geographic longitude and enhancements, onsets, and quantum jumps in chorus emissions at frequencies related to harmonics of the earth's transmission lines are discussed. The enhancement of weak emissions in the 340-360 deg dipole longitude region during quiet geomagnetic conditions is present only when ELF hiss is weak, and will not contribute to the non-adiabatic dynamics of radiation belt electrons. It is concluded that the data analyzed is consistent with a predominantly natural origin for chorus and plasmaspheric hiss, and that triggered waves do not play a major role in the non-adiabatic dynamics of geomagnetically trapped electrons.

Tsurutani, B. T.↗

NASA NTRS1979

Differential capacitance sensor as position detector for a magnetic suspension densimeter

In the present work, which consists of adapting a magnetic suspension densimeter for use at pressures up to 350 bars, a differential capacitance sensor is developed for use in the servosystem of a magnetic suspension densimeter for detecting the position of a magnetic buoy. This type of sensor has not been used previously in magnetic suspension densimeters. Its design, performance, and advantages are outlined. A cutaway drawing and a schematic diagram of the capacitance sensor and magnetic buoy are presented and described. The concentric-disk design of the sensor capacitor plates and the high degree of symmetry which results from the printed circuit fabrication approach minimize the sensor sensitivity to lateral displacement of the buoy and to the dielectric constant of the surrounding medium. A high-power microscope is necessary to monitor the position of the buoy relative to the support coil.

Frederick, N. V.↗

NASA NTRS1980

Torque control for electric motors

Method for adjusting electric-motor torque output to accomodate various loads utilizes phase-lock loop to control relay connected to starting circuit. As load is imposed, motor slows down, and phase lock is lost. Phase-lock signal triggers relay to power starting coil and generate additional torque. Once phase lock is recoverd, relay restores starting circuit to its normal operating mode.

Bernard, C. A.↗

NASA NTRS1980

A linear magnetic motor and generator

In linear magnetic motor and generator suitable for remote and hostile environments, magnetic forces drive reciprocating shaft along its axis. Actuator shaft is located in center of cylindrical body and may be supported by either contacting or noncontacting bearings. When device operates as bidirectional motor, drive coil selectively adds and subtracts magnetic flux to and from flux paths, producing forces that drive actuator along axis. When actuator is driven by external reciprocating engine, device becomes ac generator.

Studer, P. A.↗

NASA NTRS1980

Shrinking plastic tubing and nonstandard diameters

Process allows larger-than-normal postshrink diameters without splitting. Tetrafluoroethylene tubing on mandrel is supported within hot steel pipe by several small diameter coil sections. Rising temperature of mandrel is measured via thermocouple so assembly can be removed without overshrinking (and splitting) of tubing.

Ruiz, W. V.↗

NASA NTRS1981

Costs and description of a solar-energy system--Austin, Texas

Heating and cooling system uses Fresnel lens concentrating collectors. Major system components are 36 collectors, 1,500 gallon thermal storage tank, absorption cooler, cooling tower, heating coil, pumps, heat exchanger, and backup heating and air conditioning. Final report includes detailed breakdown of component and installation costs for seven project subsystems.

Source record↗

NASA NTRS1981

Eliminating gaps in split rings

Simple installation method allows thinner, lighter tether rings than conventional procedures, saving expensive materials. Installer inverts ring with pliers before it is slid over cable, then returns it to its original position after installation. Ring is in correct orientation, and coils are tightly compressed for high reliability fastening.

Gould, R. W.↗