SEARCH · Engineering Papers

Results for “capability development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

All sources NASA NTRS DOE OSTI

NASA NTRS2011

An Overview of NASA's Current Materials Development Efforts for Mars EDL

Current roadmaps point to landing heavy masses (cargo, followed by manned vehicles) on Mars in the 2030's and the existing entry, descent and landing (EDL) technology will not be sufficient to facilitate such missions. In 2009 the Exploration Technology Development Program (ETDP) established the Entry, Descent and Landing Technology Development Project (EDL TDP), to be managed programmatically at Langley Research Center (LaRC) and technically a Ames Research Center (ARC). The purpose of the project is to further the technologies required to land heavy (approximately 40 metric ton) masses on Mars to facilitate exploration. The EDL TDP contains three technical elements. They are: 1) Thermal Protection Systems (TPS) development 2) Modeling and Tools (MAT) development 3) Supersonic Retropropulsion (SRP) development The primary goals of the EDL TDP TPS element is to design and develop TPS materials capable of withstanding the severe aerothermal loads associated with aerocapture and entry into the Martian atmosphere while significantly decreasing the TPS mass fraction contribution to the entry system. Significant advancements in TPS materials technology are needed in order to enable heavy mass payloads to be successfully landed on the Martian surface for robotic precursors and subsequent human exploration missions. The EDL TDP TPS element is further divided into two different TPS concepts for Mars EDL those being: 1) Rigid TPS for a mid L/D aeroshell with the capability to withstand dual pulsed heating environments as high as 500 W/square cm for aerocapture and 130 W/square cm for entry 2) Flexible TPS for a deployable aerodynamic decelerator with the capability to withstand dual pulsed heating environments as high as 120 W/square cm for aerocapture and 30 W/square cm for entry NASA, along with its vendors, has begun developing and testing materials for each of the deceleration approaches. These include multi-layer rigid ablators and flexible ablative materials. In order to model the response of these types of materials, new and improved modeling techniques will be required. This presentation will outline the types of materials that are under development and illustrate the need for advancement in modeling of ablative materials.

Beck, Robin A.↗

NASA NTRSDate not supplied

Nuclear Space System Analysis and Modelling (NSSAM): A Software Tool to Efficiently Analyze the Design Space of Space Reactor Systems

Space reactors have the potential to play a key role in future NASA exploration activities due to their capability to enable sustainable power and advanced propulsion systems. To enable assessment of the space reactor design space, the nuclear space system analysis and modelling (NSSAM) software was developed by Analytical Mechanics Associates. NSSAM leverages a scalable and extensible software architecture which automates reactor analysis to perform coupled engine-reactor and reactor physics-thermal hydraulics calculations. This allows space reactor systems to be evaluated by a wider number of users with a consistent analysis approach to compare designs. NSSAM has been developed with multiple use cases to tailor the analysis to the level of detail desired by the user and computing resources. This summary overviews the NSSAM architecture and development approach, current capabilities (including design variants and use cases) and analysis approach for reactor and system component models.

nuclear thermal propulsion↗

NASA NTRSDate not supplied

A Brief Overview of Relevant Silicon Carbide Electronics and Sensor Development for Long Duration Venus Surface Exploration

This presentation concentrates on the potential of long duration Venus surface missions, and the role of Silicon Carbide (SiC) electronics and sensor advancements in such exploration. For example, SiC integrated circuit (IC) electronics have matured to a state where a simple long-life scientific probe is feasible for extended Venus surface operations. These electronics have been demonstrated for more than a year at 500˚C, and 60 days in high-fidelity simulated Venus surface conditions [1-2]. Further, high temperature chemical sensing technology, including SiC-based gas sensors, integrated with SiC electronics can enable future exploration of the Venus surface atmosphere [3]. Continued maturation of these high temperature electronics and sensors has been part of the Long-Lived In-Situ Solar System Explorer (LLISSE) project to provide an operational system for in situ exploration of the Venus surface up to 60 days [4]. A key focus of this work includes increasing the complexity and decreasing the power consumption of the ICs which will pave the way to enhanced capabilities, such as long-duration Venus seismic measurements and other mission capabilities currently under development. This is in parallel to work expanding the capabilities of the sensor technology to provide science measurements on the Venus surface. This presentation will give an overview of possible extended duration Venus surface exploration and some of the SiC-based technologies that can enable this exploration.

high temperature Venus surface electronics sensors↗

NASA NTRSDate not supplied

Computational and Physics-Based Modeling for the Development of in-Space Welding Technology

Welding will be an enabling technology for in-space assembly and manufacturing (ISAM) and in-space repair operations in support of the growing Space Economy. Prospective use cases of welding include metal repair on long-duration lunar surface missions and assembly of large structures that exceed dimensions of the currently available launch vehicle envelopes such as space arrays, tall lunar transmission towers, or even large transit vehicles powered by nuclear propulsion. There is a brief history of beam welding for in-space use. Soviet and NASA astronauts performed electron beam welds (EBW) in space in the late-1960s through mid-1980s and several parabolic flights of laser beam welding (LBW) were undertaken in the USA and Canada in the early-1990s. Work has since stagnated until the recent boom of the in-space economy has demonstrated need for continued development of EBW and LBW processes, which are desirable for their compactness, low mass, low power consumption, and high wall plug efficiency. No space-based manufacturing laboratory capable of demonstrating, developing, and applying welding processes exists, and costs are high to develop and fly individual space-based trials. This drives the current approach to develop welding technology with computational and physics-based models in tandem with earth-based experiments. Several approaches are taken to complement and drive the selection of instrumentation for planned parabolic and suborbital flights. First, a thermal model of Skylab EBW experiments is established and compared to empirical data. Next, the model is used to show variation between Earth-based and in-space weld structure and properties through exploration of key variables that define the Low earth orbit and lunar surface space environments, namely temperature (40 – 400 K), pressure (10-10 to 104 Pa), and gravity (10-6 g to 1 g). Finally, physical processes associated with heat and mass transport during welding are evaluated through several case studies across the above variable ranges demonstrating need for further research.

in-space welding↗

NASA NTRS1983

Development and use of an integrated analysis capability

The paper describes a multi-discipline integrated analysis capability, designed to aid the engineering community in coupling of existing modules and in handling of the associated software and data. This capability consists of an executive program which manages tasks and data, a number of technical modules, graphics and special purpose modules, inter-module data flow interfaces, and associated user documentation. The current implementation provides specific modules and coupled solution paths for the thermal, structures and controls technologies. However, the system has been designed to serve also as a framework into which user groups may incorporate other modules and technologies. Details of the system architecture are discussed, in the context of the major design decisions and the software development and usage experience. The paper provides a brief discussion of some other integrated systems which are available or under development.

Vos, R. G.↗

NASA NTRS2015

Lidar Sensor Performance in Closed-Loop Flight Testing of the Morpheus Rocket-Propelled Lander to a Lunar-Like Hazard Field

For the first time, a suite of three lidar sensors have been used in flight to scan a lunar-like hazard field, identify a safe landing site, and, in concert with an experimental Guidance, Navigation, and Control (GN&C) system, guide the Morpheus autonomous, rocket-propelled, free-flying test bed to a safe landing on the hazard field. The lidar sensors and GN&C system are part of the Autonomous Precision Landing and Hazard Detection and Avoidance Technology (ALHAT) project which has been seeking to develop a system capable of enabling safe, precise crewed or robotic landings in challenging terrain on planetary bodies under any ambient lighting conditions. The 3-D imaging flash lidar is a second generation, compact, real-time, air-cooled instrument developed from a number of cutting-edge components from industry and NASA and is used as part of the ALHAT Hazard Detection System (HDS) to scan the hazard field and build a 3-D Digital Elevation Map (DEM) in near-real time for identifying safe sites. The flash lidar is capable of identifying a 30 cm hazard from a slant range of 1 km with its 8 cm range precision at 1 sigma. The flash lidar is also used in Hazard Relative Navigation (HRN) to provide position updates down to a 250m slant range to the ALHAT navigation filter as it guides Morpheus to the safe site. The Doppler Lidar system has been developed within NASA to provide velocity measurements with an accuracy of 0.2 cm/sec and range measurements with an accuracy of 17 cm both from a maximum range of 2,200 m to a minimum range of several meters above the ground. The Doppler Lidar's measurements are fed into the ALHAT navigation filter to provide lander guidance to the safe site. The Laser Altimeter, also developed within NASA, provides range measurements with an accuracy of 5 cm from a maximum operational range of 30 km down to 1 m and, being a separate sensor from the flash lidar, can provide range along a separate vector. The Laser Altimeter measurements are also fed into the ALHAT navigation filter to provide lander guidance to the safe site. The flight tests served as the culmination of the TRL 6 journey for the lidar suite and included launch from a pad situated at the NASA-Kennedy Space Center Shuttle Landing Facility (SLF) runway, a lunar-like descent trajectory from an altitude of 250m, and landing on a lunar-like hazard field of rocks, craters, hazardous slopes, and safe sites 400m down-range just off the North end of the runway. The tests both confirmed the expected performance and also revealed several challenges present in the flight-like environment which will feed into future TRL advancement of the sensors. The flash lidar identified hazards as small as 30 cm from the maximum slant range of 450 m which Morpheus could provide, however, it was occasionally susceptible to an increase in range noise due to heated air from the Morpheus rocket plume which entered its Field-of-View (FOV). The flash lidar was also susceptible to pre-triggering on dust during the HRN phase which was created during launch and transported by the wind. The Doppler Lidar provided velocity and range measurements to the expected accuracy levels yet it was also susceptible to signal degradation due to air heated by the rocket engine. The Laser Altimeter, operating with a degraded transmitter laser, also showed signal attenuation over a few seconds at a specific phase of the flight due to the heat plume generated by the rocket engine.

Roback, Vincent E.↗

DOE OSTI2022

Sierra/SolidMechanics 5.8 In-Development Manual

This user’s guide documents capabilities in Sierra/SolidMechanics which remain “in-development” and thus are not tested and hardened to the standards of capabilities listed in Sierra/SM 5.8 User’s Guide. Capabilities documented herein are available in Sierra/SM for experimental use only until their official release. These capabilities include, but are not limited to, novel discretization approaches such as the conforming reproducing kernel (CRK) method, numerical fracture and failure modeling aids such as the extended finite element method (XFEM) and J-integral, explicit time step control techniques, dynamic mesh rebalancing, as well as a variety of new material models and finite element formulations.

42 ENGINEERING↗

DOE OSTI2022

Sierra/SolidMechanics 5.10 In-Development Manual

This user’s guide documents capabilities in Sierra/SolidMechanics which remain “in-development” and thus are not tested and hardened to the standards of capabilities listed in Sierra/SM 5.10 User’s Guide. Capabilities documented herein are available in Sierra/SM for experimental use only until their official release. These capabilities include, but are not limited to, novel discretization approaches such as the conforming reproducing kernel (CRK) method, numerical fracture and failure modeling aids such as the extended finite element method (XFEM) and J-integral, explicit time step control techniques, dynamic mesh rebalancing, as well as a variety of new material models and finite element formulations.

42 ENGINEERING↗

NASA NTRSDate not supplied

A Hybrid CFD/Engineering Model Tool for Lunar Lander Surface Erosion Prediction

Plume-Surface Interaction (PSI) between lander engine plumes and landing area regolith poses risks to the landers and space exploration missions through view obscuration and high-energy ejecta impacts from eroded particle clouds and vehicle tilting from plume-induced craters. To address these risks, NASA MSFC Fluid Dynamics Branch (ER42) has developed a cascade of predictive simulation capabilities for PSI, including the recent development of a hybrid CFD/engineering model tool that allows for rapid PSI simulations with a descending/ascending vehicle and an eroding surface. The development of this fully-coupled, moving body/eroding surface simulation capability is detailed along with a demonstration of the tool’s capabilities on the Apollo 12 Lunar Module landing. Predictions of eroded mass flow rates as a function of time are verified against Apollo 12 flight data, from which the developed, viscous erosion model has been calibrated.

Plume Surface Interaction↗

NASA NTRSDate not supplied

A Hybrid CFD/Engineering Model Tool for Lunar Lander Surface Erosion Prediction

Plume Surface Interaction↗

NASA NTRS1972

Performance evaluation capabilities for the design of physical systems

The results are presented of a study aimed at developing and formulating a capability for the limiting performance of large steady state systems. The accomplishments reported include: (1) development of a theory of limiting performance of large systems subject to steady state inputs; (2) application and modification of PERFORM, the computational capability for the limiting performance of systems with transient inputs; and (3) demonstration that use of an inherently smooth control force for a limiting performance calculation improves the system identification phase of the design process for physical systems subjected to transient loading.

Pilkey, W. D.↗

NASA NTRS1998

Development of High Conductivity Lithium-Ion Electrolytes for Low Temperature Cell Applications

NASA has continued interest in developing power sources which are capable of operating at low temperatures (-20 C and below) to enable future missions, such as the Mars Rover and Lander. Thus, under a program sponsored by the Mars Exploration Program, we have been involved in developing Li-ion batteries with improved low temperature performance. To accomplish this task, the focus of the research has been upon the development of advanced electrolyte systems with improved low temperature properties. This had led to the identification of a carbonate-based electrolyte, consisting of 1.0 M LiPF6 in EC + DEC + DMC (33:33:34), which has been shown to have excellent performance at -20 C in Li-ion AA-size prototype cells. Other groups are also actively engaged in developing electrolytes which can result in improved low temperature performance of Li-ion cells, including Polystor, Yardney, and Covalent. In addition to developing cells capable of operation at -20 C, there is continued interest in systems which can successfully operate at even lower temperatures (less than -30 C) and at high discharge rates (greater than C/2). Thus, we are currently focusing upon developing advanced electrolytes which are highly conductive at low temperatures and will result in cells capable of operation at -40 C. One approach to improve the low temperature conductivity of ethylene carbonate-based electrolytes involves adding co-solvents which will decrease the viscosity and extend the liquid range. Candidate solvent additives include formates, acetates, cyclic and aliphatic ethers, lactones, as well as other carbonates. Using this approach, we have prepared a number of electrolytes which contain methyl formate (MF), methyl acetate (MA), ethyl acetate (EA), ethyl proprionate (EP), and 1,2-dimethoxyethane (DME), some of which have been characterized and reported. Other groups have also reported electrolytes based on mixtures of carbonates and acetates. In the present study, electrolytes which have been identified to have good low temperature conductivity and stability were incorporated into lithium-graphite cells for evaluation. Using various electrochemical methods, including ac impedence and DC micropolarization techniques, the film formation characteristics of graphite electrodes in contact with various lectrolyte formulations was investigated.

Smart, M. C.↗

DOE OSTI2020

TRUST-EABM Nonlinear Dynamics (ND) Report (Release FY2020-1.1)

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) project is to support the efficient and responsive development of experimental, modeling, and simulation capabilities for future systems by developing representative testbeds that can be exercised more easily and efficiently than a WR-like assembly for the purposes uncertainty quantification. The testbeds are intended to be experimentally exercised in current and future relevant engineering environments with complementary modeling and simulation.

42 ENGINEERING↗

DOE OSTI2020

TRUST-EABM Sensors in Environments (SE) Report: Release FY20

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) project is to support the efficient and responsive development of experimental, modeling, and simulation capabilities for future systems by developing representative testbeds that can be exercised more easily and efficiently than a WR like assembly for the purposes uncertainty quantification [1][2][3]. The testbeds are intended to be experimentally exercised in current and future relevant engineering environments with complementary modeling and simulation.

47 OTHER INSTRUMENTATION↗

NASA NTRS2004

Status of Low Thrust Work at JSC

High performance low thrust (solar electric, nuclear electric, variable specific impulse magnetoplasma rocket) propulsion offers a significant benefit to NASA missions beyond low Earth orbit. As NASA (e.g., Prometheus Project) endeavors to develop these propulsion systems and associated power supplies, it becomes necessary to develop a refined trajectory design capability that will allow engineers to develop future robotic and human mission designs that take advantage of this new technology. This ongoing work addresses development of a trajectory design and optimization tool for assessing low thrust (and other types) trajectories. This work targets to advance the state of the art, enable future NASA missions, enable science drivers, and enhance education. This presentation provides a summary of the low thrust-related JSC activities under the ISP program and specifically, provides a look at a new release of a multi-gravity, multispacecraft trajectory optimization tool (Copernicus) along with analysis performed using this tool over the past year.

Condon, Gerald L.↗

NASA NTRS2006

An Overview of Space Exploration Simulation (Basis of Confidence) Documentation

Models and simulations (M&S) are critical resources in the exploration of space. They support program management, systems engineering, integration, analysis, test, and operations by providing critical information that supports key analyses and decisions (technical, cost and schedule). Consequently, there is a clear need to establish a solid understanding of M&S strengths and weaknesses, and the bounds within which they can credibly support decision making. In this presentation we will describe how development of simulation capability documentation will be used to form a Basis of Confidence (Basis of Confidence) for National Aeronautics and Space Administration (NASA) M&S. The process by which BOC documentation is developed will be addressed, as well as the structure and critical concepts that are essential for establishing credibility of NASA's Exploration Systems Mission Directorate (ESMD) legacy M&S. We will illustrate the significance of BOC documentation in supporting decision makers and Accreditation Authorities in M&S risk management.

Bray, Alleen↗

NASA NTRS2009

Workshop on Sustainable Infrastructure with NASA Science Mission Directorate and NASA's Office of Infrastructure Representatives

NASA conducted a workshop in July 2009 to bring together their experts in the climate science and climate impacts domains with their institutional stewards. The workshop serves as a pilot for how a federal agency can start to: a) understand current and future climate change risks, b) develop a list of vulnerable institutional capabilities and assets, and c) develop next steps so flexible adaptation strategies can be developed and implemented. 63 attendees (26 scientists and over 30 institutional stewards) participated in the workshop, which extended across all or part of three days.

Rosenzweig, Cynthia↗

NASA NTRS2009

Workshop on Sustainable Infrastructure with NASA Science Mission Directorate and NASA's Office of Infrastructure Representatives

Rosenzweig, Cynthia↗