Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “blade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96
All sourcesNASA NTRSDOE OSTI
NASA NTRS1922

Deflection of Propeller Blades While Running

The forces acting on the blades of a propeller proceed from the mass of the propeller and the resistance of the surrounding medium. The magnitude, direction and point of application of the resultant to the propeller blade is of prime importance for the strength calculation. Since it was obviously impracticable to bring any kind of testing device near the revolving propeller, not so much on account of the element of danger as on account of the resulting considerable disturbance of the air flow, the deflection in both cases was photographically recorded and subsequently measured at leisure.

PROPELLERS - DEFLECTION↗
NASA NTRS1952

The Langley 2,000-horsepower Propeller Dynamometer and Tests at High Speed of an NACA 10-(3)(08)-03 Two-blade Propeller

This paper contains a detailed description of a 2,000-horsepower propeller dynamometer used to make wind-tunnel tests of a two-blade NACA 10-(3)(08)-03 propeller for a range of blade angles from 20 degrees to 55 degrees at airspeeds up to 500 miles per hour. The results of these tests and comparisons with results obtained from a theoretical analysis and from previous tests made in other wind tunnels are presented.

RESEARCH EQUIPMENT, PROPELLER↗
NASA NTRS1953

Effect of a Rapid Blade-Pitch Increase on the Thrust and Induced-Velocity Response of a Full-Scale Helicopter Rotor

A method has been proposed for predicting the effect of a rapid blade-pitch increase on the thrust and induced-velocity response of a helicopter rotor. General equations have been derived for the ensuing motion of the helicopter. These equations yield time histories of thrust, induced velocity, and helicopter vertical velocity for given rates of blade-pitch-angle changes and given rotor-angular-velocity time histories. The results of the method have been compared with experimental results obtained with a rotor mounted on the Langley helicopter test tower. The calculated and experimental results are in good agreement, although, in general, the calculated thrust-coefficient overshoots are about 10 percent greater than those obtained experimentally.

Carpenter, Paul J↗
NASA NTRS1957

Summary of 65-Series Compressor-Blade Low-Speed Cascade Data by Use of the Carpet-Plotting Technique

The carpet-plotting technique is presented in this paper as a more useful and concise method of summarizing cascade data on the NACA 65-series compressor blades given in NACA Technical Note 3916. Carpet plots included permit the selection of the blade camber and the design angle of attack required to fulfill a design vector diagram. Other carpet plots provide means for the prediction of off-design turning angles. Also presented are carpet plots of an isentropic pressure-rise coefficient as a entering Mach number.

COMPRESSORS - AXIAL-FLOW↗
NASA NTRS1948

Empirical mode constants for calculating frequencies of axial-flow compressor blades

The vibration characteristics of a group of axial-flow compressor blades of similar geometry were investigated. Empirical-mode constants were determined for the first three bending and torsional modes. A comparison of experimentally determined frequencies of a second group of blades with frequencies computed using these mode constants showed that the computed values were correct within 10 percent. The approximate limiting ratios of depth to chord and length to chord below which these constants could not be used to compute the natural frequencies were also found experimentally.

COMPRESSORS - STRESS AND VIBRATION↗
NASA NTRS1950

Analytical determination of local surface heat-transfer coefficients for cooled turbine blades from measured metal temperatures

Analytical methods are presented for the determination of local values of outside and inside heat-transfer coefficients and effective gas temperatures by use of turbine-blade-temperature measurements. The methods are derived for a number of configurations that can be applied to typical cooled-turbine-blade shapes as well as to other types of heat-transfer apparatus.

TURBINE COOLING↗
NASA NTRS1951

Calculations of Laminar Heat Transfer Around Cylinders of Arbitrary Cross Section and Transpiration-Cooled Walls with Application to Turbine Blade Cooling

An approximate method for development of flow and thermal boundary layers in laminar regime on cylinders with arbitrary cross section and transpiration-cooled walls is obtained by use of Karman's integrated momentum equation and an analogous heat-flow equation. Incompressible flow with constant property values throughout boundary layer is assumed. Shape parameters for approximated velocity and temperature profiles and functions necessary for solution of boundary-layer equations are presented as charts, reducing calculations to a minimum. The method is applied to determine local heat-transfer coefficients and surface temperature-cooled turbine blades for a given flow rate. Coolant flow distributions necessary for maintaining uniform blade temperatures are also determined.

TURBINE COOLING↗
NASA NTRS1954

Review of high-performance axial-flow-compressor blade-element theory

This report presents a review of current compressor blade-element theory with particular emphasis on application to the transonic high-performance compressor. A discussion of the significant parameters of total-pressure loss and deviation angle is presented, and an indication of the extent of available knowledge and the problems involved in the determination of blade-element characteristics is given. Some recent results and considerations in this pursuit and suggestions for further avenues of investigation are indicated.

Lieblein, Seymour↗
NASA NTRS1954

An Experimental Investigation of Hollow Turbine Blades for Expandable Jet Engines

An experimental investigation was made to determine the feasibility of using hollow turbine blades in engines designed for short service life. Airfoils were fabricated from sheet material and techniques of welding and brazing attachment were investigated. The airfoils were not intended to be cooled. A principal objective was the reduction of strategic material requirements primarily as a function of direct weight reduction. The materials considered were in the density range of 0.28 to 0.31 pound per cubic inch. Three materials were used for airfoils: N-155, Inconel-X and L-605. These were attached to J47 turbine blade bases and operated to destruction at maximum service conditions of turbine speed and temperature. It was found that L-605 airfoils brazed to suitable bases satisfied the requirements for expendable engines. Service life varied from 11 to 40 hours.

Morgan, W C↗
NASA NTRS1957

Identification of Foreign Objects Damaging Compressor Blades in Turbojet Engines

Damage to the compressor blades of turbojet engines due to ingestion of foreign objects is a growing problem, the solution of which has been made more difficult by the large percentage of damaging materials that have remained unknown. A rapid emission spectroscopic method was devised to identify the chemical composition of these foreign objects. Results on laboratory-prepared specimens and blades from damaged engines show that the method can be utilized to determine the nature of the ingested foreign objects.

Spakowski, A E↗
NASA NTRS1951

Relation of Engine Turbine-blade Life to Stress-rupture Properties of the Alloys, Stellite 21, Hastelloy B, Cast S-816, Forged S-816, X-40, Nimonic 80, Refractaloy 26, N-155, and Inconel X

An investigation was conducted to relate the engine performance of the heat-resistant alloys, Stellite 21, Hastelloy B, cast S-816, forged S-816, X-40, Nimonic 80, Refractory 26, N-155, and Iconel X to their stress-rupture properties. The engine test consisted of the repetition of a 20-minute cycle, 15 minutes at rated speed and approximately 5 minutes at idle. The results of the investigation indicated a direct correlation between stress-rupture life and blade life for the relatively low-strength alloys. The stress-rupture life and blade life for the relatively high-strength alloys did not correlate because of the effects of the vibratory stresses and the corrosive-gas atmosphere.

ALLOYS, HEAT-RESISTING↗
NASA NTRS1931

Full-Scale Wind-Tunnel Tests on Several Metal Propellers Having Different Blade Forms

This report gives the full-scale aerodynamic characteristics of five different aluminum alloy propellers having four different blade forms. They were tested on an open cockpit fuselage with a radial air-cooled engine having conventional cowling. The results show that (1) the differences in propulsive efficiency due to the differences in blade form were small; (2) the form with the thinnest airfoil sections had the highest efficiency; (3) it is advantageous as regards propulsive efficiency for a propeller operating in front of a body, such as a radial engine, to have its pitch reduced toward the hub.

Weick, Fred E↗
NASA NTRS1937

An analytical and experimental study of the effect of periodic blade twist on the thrust, torque, and flapping motion of an autogiro rotor

An analysis is made of the influence on autogiro rotor characteristics of a periodic blade twist that varies with the azimuth position of the rotor blade and the results are compared with experimental data. The analysis expresses the influence of this type of twist upon the thrust, torque, and flapping motion of the rotor. The check against experimental data shows that the periodic twist has a pronounced influence on the flapping motion and that this influence is accurately predicted by the analysis. The influence of the twist upon the thrust and torque could be demonstrated only indirectly, but its importance is indicated.

Wheatley, John B↗
NASA NTRS1938

The Torsional and Bending Deflection of Full-Scale Aluminum-Alloy Propeller Blades Under Normal Operating Conditions

The torsional deflection of the blades of three full-scale aluminum-alloy propellers operating under various loading conditions was measured by a light-beam method. Angular bending deflections were also obtained as an incidental part of the study. The deflection measurements showed that the usual present-day type of propeller blades twisted but a negligible amount under ordinary flight conditions. A maximum deflection of about 1/10 degree was found at a v/nd of 0.3 and a smaller deflection at higher values of v/nd for the station at 0.70 radius. These deflections are much smaller than would be expected from earlier tests, but the light-beam method is considered to be much more accurate than the direct-reading-transit method used in the previous test.

Hartman, Edwin P↗
NASA NTRS1950

Method of designing cascade blades with prescribed velocity distributions in compressible potential flows

By use of the assumption that the pressure-volume relation is linear, a solution to the problem of designing a cascade for a given turning and with a prescribed velocity distribution along the blade in a potential flow of a compressible perfect fluid was obtained by a method of correspondence between potential flows of compressible and incompressible fluids. The designing of an isolated airfoil with a prescribed velocity distribution along the airfoil is considered as a special case of cascade. If the prescribed velocity distribution is not theoretically attainable, the method provides a means of modifying the distribution so as to obtain a physically significant blade shape. Numerical examples are included.

Costello, George R↗
NASA NTRS1952

Detailed computational procedure for design of cascade blades with prescribed velocity distributions in compressible potential flows

A detailed step-by-step computational outline is presented for the design of two-dimensional cascade blades having a prescribed velocity distribution on the blade in a potential flow of the usual compressible fluid. The outline is based on the assumption that the magnitude of the velocity in the flow of the usual compressible nonviscous fluid is proportional to the magnitude of the velocity in the flow of a compressible nonviscous fluid with linear pressure-volume relation.

Costello, George R↗
NASA NTRS1955

Calculations of Laminar Heat Transfer Around Cylinders of Arbitrary Cross Section and Transpiration-Cooled Walls with Application to Turbine Blade Cooling

An approximate method for the development of flow and thermal boundary layers in the laminar region on cylinders with arbitrary cross section and transpiration-cooled walls is obtained by the use of Karman's integrated momentum equation and an analogous heat-flow equation. Incompressible flow with constant property values throughout the boundary layer is assumed. The velocity and temperature profiles within the boundary layer are approximated by expressions composed of trigonometric functions. Shape parameters for these profiles and functions necessary for the solution of the boundary-layer equations are presented as graphs so that the calculation for any specific case is reduced to the solution of two first-order differential equations. This method is applied to determine local heat-transfer coefficients and surface temperatures in the laminar flow region of the transpiration-cooled turbine blades for a given coolant flow rate, or to calculate the coolant flow distribution which is necessary in order to keep the blade temperature uniform along the surface.

Eckert, E R G↗
NASA NTRS1958

Theory of self-excited mechanical oscillations of helicopter rotors with hinged blades

Vibrations of rotary-wing aircraft may derive their energy from the rotation of the rotor rather than from the air forces. A theoretical analysis of these vibrations is described and methods for its application are explained in Chapter one. Chapter two reports the results of an investigation of the mechanical stability of a rotor having two vertically hinged blades mounted upon symmetrical supports, that is, of equal stiffness and mass in all horizontal directions. Chapter three presents the theory of ground vibrations of a two-blade helicopter rotor on anisotropic flexible supports.

Coleman, Robert P↗