Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VIBRATION EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Active Flap Control of the SMART Rotor for Vibration Reduction

Active control methodologies were applied to a full-scale active flap rotor obtained during a joint Boeing/ DARPA/NASA/Army test in the Air Force National Full-Scale Aerodynamic Complex 40- by 80-foot anechoic wind tunnel. The active flap rotor is a full-scale MD 900 helicopter main rotor with each of its five blades modified to include an on-blade piezoelectric actuator-driven flap with a span of 18% of radius, 25% of chord, and located at 83% radius. Vibration control demonstrated the potential of active flaps for effective control of vibratory loads, especially normal force loads. Active control of normal force vibratory loads using active flaps and a continuous-time higher harmonic control algorithm was very effective, reducing harmonic (1-5P) normal force vibratory loads by 95% in both cruise and approach conditions. Control of vibratory roll and pitch moments was also demonstrated, although moment control was less effective than normal force control. Finally, active control was used to precisely control blade flap position for correlation with pretest predictions of rotor aeroacoustics. Flap displacements were commanded to follow specific harmonic profiles of 2 deg or more in amplitude, and the flap deflection errors obtained were less than 0.2 deg r.m.s.

Hall, Steven R.↗

Wind Tunnel Test of the SMART Active Flap Rotor

Boeing and a team from Air Force, NASA, Army, DARPA, MIT, UCLA, and U. of Maryland have successfully completed a wind-tunnel test of the smart material actuated rotor technology (SMART) rotor in the 40- by 80-foot wind-tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center. The Boeing SMART rotor is a full-scale, five-bladed bearingless MD 900 helicopter rotor modified with a piezoelectric-actuated trailing edge flap on each blade. The eleven-week test program evaluated the forward flight characteristics of the active-flap rotor at speeds up to 155 knots, gathered data to validate state-of-the-art codes for rotor aero-acoustic analysis, and quantified the effects of open and closed loop active flap control on rotor loads, noise, and performance. The test demonstrated on-blade smart material control of flaps on a full-scale rotor for the first time in a wind tunnel. The effectiveness of the active flap control on noise and vibration was conclusively demonstrated. Results showed significant reductions up to 6dB in blade-vortex-interaction and in-plane noise, as well as reductions in vibratory hub loads up to 80%. Trailing-edge flap deflections were controlled within 0.1 degrees of the commanded value. The impact of the active flap on control power, rotor smoothing, and performance was also demonstrated. Finally, the reliability of the flap actuation system was successfully proven in more than 60 hours of wind-tunnel testing.

Straub, Friedrich K.↗

Gear Fault Detection Effectiveness as Applied to Tooth Surface Pitting Fatigue Damage

A study was performed to evaluate fault detection effectiveness as applied to gear tooth pitting fatigue damage. Vibration and oil-debris monitoring (ODM) data were gathered from 24 sets of spur pinion and face gears run during a previous endurance evaluation study. Three common condition indicators (RMS, FM4, and NA4) were deduced from the time-averaged vibration data and used with the ODM to evaluate their performance for gear fault detection. The NA4 parameter showed to be a very good condition indicator for the detection of gear tooth surface pitting failures. The FM4 and RMS parameters performed average to below average in detection of gear tooth surface pitting failures. The ODM sensor was successful in detecting a significant amount of debris from all the gear tooth pitting fatigue failures. Excluding outliers, the average cumulative mass at the end of a test was 40 mg.

Lewicki, David G.↗

Rotorcraft Transmission Noise Path Model, Including Distributed Fluid Film Bearing Impedance Modeling

A computational approach for simulating the effects of rolling element and journal bearings on the vibration and sound transmission through gearboxes has been demonstrated. The approach, using ARL/Penn State s CHAMP methodology, uses Component Mode Synthesis of housing and shafting modes computed using Finite Element (FE) models to allow for rapid adjustment of bearing impedances in gearbox models. The approach has been demonstrated on NASA GRC s test gearbox with three different bearing configurations: in the first condition, traditional rolling element (ball and roller) bearings were installed, and in the second and third conditions, the traditional bearings were replaced with journal and wave bearings (wave bearings are journal bearings with a multi-lobed wave pattern on the bearing surface). A methodology for computing the stiffnesses and damping in journal and wave bearings has been presented, and demonstrated for the journal and wave bearings used in the NASA GRC test gearbox. The FE model of the gearbox, along with the rolling element bearing coupling impedances, was analyzed to compute dynamic transfer functions between forces applied to the meshing gears and accelerations on the gearbox housing, including several locations near the bearings. A Boundary Element (BE) acoustic model was used to compute the sound radiated by the gearbox. Measurements of the Gear Mesh Frequency (GMF) tones were made by NASA GRC at several operational speeds for the rolling element and journal bearing gearbox configurations. Both the measurements and the CHAMP numerical model indicate that the journal bearings reduce vibration and noise for the second harmonic of the gear meshing tones, but show no clear benefit to using journal bearings to reduce the amplitudes of the fundamental gear meshing tones. Also, the numerical model shows that the gearbox vibrations and radiated sound are similar for journal and wave bearing configurations.

Hambric, Stephen A.↗

Evaluation of Heat Recuperation in a Concentric Hydrogen Reduction Reactor

Heat recuperation in an ISRU reactor system involves the recovery of heat from a reacted regolith batch by transferring this energy into a batch of fresh regolith. One concept for a hydrogen reduction reactor is a concentric chamber design where heat is transferred from the inner, reaction chamber into fresh regolith in the outer, recuperation chamber. This concept was tested and analyzed to define the overall benefit compared to a more traditional single chamber batch reactor. Data was gathered for heat-up and recuperation in the inner chamber alone, simulating a single chamber design, as well as recuperation into the outer chamber, simulating a dual chamber design. Experimental data was also used to improve two analytical models, with good agreement for temperature behavior during recuperation, calculated mass of the reactor concepts, and energy required during heat-up. The five tests, performed using JSC-1A regolith simulant, also explored the effectiveness of helium gas fluidization, hydrogen gas fluidization, and vibrational fluidization. Results indicate that higher hydrogen volumetric flow rates are required compared to helium for complete fluidization and mixing, and that vibrational fluidization may provide equivalent mixing while eliminating the need to flow large amounts of excess hydrogen. Analysis of the total energy required for heat-up and steady-state operations for a variety of conditions and assumptions shows that the dual-chamber concept requires the same or more energy than the single chamber concept. With no clear energy savings, the added mass and complexity of the dual-chamber makes it unlikely that this design concept will provide any added benefit to the overall ISRU oxygen production system.

Linne, Diane↗

Near real-time ORM measurements and SVD matrix generation for 10 Hz global orbit feedback in RHIC

To reduce the effect of trajectory perturbations ({approx}10 Hz) due to vibrations of the final focusing quadrupoles at RHIC, global orbit feedback was successfully prototyped during run-10. After upgraded to a system with 36 BPMs and 12 correctors, 10 Hz feedback was tested successfully in Run-11 and is in operational status for physics program. The test and operation of the system has been performed using transfer functions between the beam position monitors and correctors obtained from the online optics model and a correction algorithm based on singular value decomposition (SVD). One of our goals is to self-calibrate the system using SVD matrices derived from orbit response matrix (ORM) measurements acquired real-time using the new FPGA-based signal processing. Comparisons between measurement matrix and model matrix and the generation of SVD matrix for the feedback operation are presented.

43 PARTICLE ACCELERATORS↗

Nonlocal thermodynamic equilibrium effects in stratospheric NO and implications for infrared remote sensing

It is shown that the vibrational state population of stratospheric nitric oxide (NO) could be substantially different from that expected on the basis of LTE. Deviations from LTE may arise because stratospheric NO can be photochemically produced from NO2 with several vibrational quanta. Model calculations suggest that the population of NO(v = 1) could be some 30 percent above that expected from LTE at 30 km, with smaller enhancements above and below. Substantially larger enhancements are predicted for NO(v = 2). This result is shown to have important implications for NO determination by remote sensing of IR emission. Data needed for the quantification of these effects are enumerated.

Kaye, Jack A.↗

The Debye-Waller factor of disordered solids: The case for amorphous silicon

This paper presents a first-principles study of the Debye-Waller factor and the Debye temperature for amorphous silicon (α-Si) from lattice-dynamical calculations and direct molecular-dynamics simulations using density-functional theory (DFT). The effects of temperature and structural disorder on the intensity of the diffraction maxima and the vibrational mean-square displacement (MSD) of Si atoms are studied in the harmonic approximation, with particular emphasis on the bond-length disorder, the presence of coordination defects, and microvoids in α-Si networks. It has been observed that the MSDs associated with tetrahedrally bonded Si atoms are considerably lower than their dangling-bond counterparts—originating from isolated and vacancy-induced clustered defects—and those on the surface of microvoids, leading to an asymmetric non-Gaussian tail in the distribution of atomic displacements. An examination of the effect of anharmonicity on the MSD at high temperatures using direct ab initio molecular-dynamics simulations (without the harmonic approximation) suggests that the vibrational motion in α-Si is practically unaffected by anharmonic effects at temperatures below 400 K, as far as the present DFT calculations are concerned. The Debye temperature of α-Si is found to be in the range of 488–541 K from specific-heat and MSD calculations using first-principles lattice-dynamical calculations in the harmonic approximation, which matches closely with the experimental value of 487–528 K obtained from specific-heat measurements of α-Si at low temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ab initio studies of the impact of the Debye-Waller factor on the structural and dynamical properties of amorphous semiconductors: The case of a-Si

This paper presents a first-principles study of the Debye-Waller factor and the Debye temperature for amorphous silicon (a-Si) from lattice-dynamical calculations and direct molecular-dynamics simulations using density-functional theory (DFT). The effects of temperature and structural disorder on the intensity of the diffraction maxima and the vibrational mean-square displacement (MSD) of Si atoms are studied in the harmonic approximation, with particular emphasis on the bond-length disorder, the presence of coordination defects, and microvoids in a-Si networks. It has been observed that the MSDs associated with tetrahedrally-bonded Si atoms are considerably lower than their dangling-bond counterparts – originating from isolated and vacancy-induced clustered defects – and those on the surface of microvoids, leading to an asymmetric non-gaussian tail in the distribution of atomic displacements. An examination of the effect of anharmonicity on the MSD at high temperatures using direct ab initio molecular-dynamics simulations (without the harmonic approximation) suggests that the vibrational motion in a-Si is practically unaffected by anharmonic effects at temperatures below 400 K, as far as the present DFT calculations are concerned. The Debye temperature of a-Si is found to be in the range of 488–541 K from specific-heat and MSD calculations using first-principles lattice-dynamical calculations in the harmonic approximation, which matches closely with the experimental value of 487–528 K obtained from specific-heat measurements of a-Si at low temperatures.

36 MATERIALS SCIENCE↗

Out-of-resonance vibration modulation of ultrasound with a nonlinear oscillator for microcrack detection in a cantilever beam

This Letter reports an out-of-resonance vibro-acoustic modulation (VAM) effect in nonlinear ultrasonic evaluation of a microcracked cantilever beam. We design a model to involve the microcracked cantilever beam in a nonlinear oscillator system whose dynamics is introduced to extend the operating vibration excitation band of the VAM out of resonance. The prototype model exhibits an effective bandwidth four times that of the traditional linear model. The reported VAM effect allows efficiently enhancing the detection, localization, and imaging of various types of microcracks in solid materials at out-of-resonance vibration excitation frequencies.

36 MATERIALS SCIENCE↗

Understanding Heterogeneities in Quantum Materials

Quantum materials are usually heterogeneous, with structural defects, impurities, surfaces, edges, interfaces, and disorder. These heterogeneities are sometimes viewed as liabilities within conventional systems; however, their electronic and magnetic structures often define and affect the quantum phenomena such as coherence, interaction, entanglement, and topological effects in the host system. Therefore, a critical need is to understand the roles of heterogeneities in order to endow materials with new quantum functions for energy and quantum information science applications. In this article, several representative examples are reviewed on the recent progress in connecting the heterogeneities to the quantum behaviors of real materials. Specifically, three intertwined topic areas are assessed: i) Reveal the structural, electronic, magnetic, vibrational, and optical degrees of freedom of heterogeneities. ii) Understand the effect of heterogeneities on the behaviors of quantum states in host material systems. iii) Control heterogeneities for new quantum functions. This progress is achieved by establishing the atomistic-level structure-property relationships associated with heterogeneities in quantum materials. Finally, the understanding of the interactions between electronic, magnetic, photonic, and vibrational states of heterogeneities enables the design of new quantum materials, including topological matter and quantum light emitters based on heterogenous 2D materials.

36 MATERIALS SCIENCE↗

High-resolution photoelectron imaging of cold C{sub 60}{sup −} anions and accurate determination of the electron affinity of C{sub 60}

High-resolution photoelectron imaging and spectroscopy of cold C{sub 60}{sup −} anions are reported using a newly built photoelectron imaging apparatus coupled with an electrospray ionization source and a temperature-controlled cryogenic ion trap. Vibrationally resolved photoelectron spectra are obtained for the detachment transition from the ground state of C{sub 60}{sup −} to that of C{sub 60} at various detachment wavelengths from 354.84 nm to 461.35 nm. The electron affinity of C{sub 60} is accurately measured to be 2.6835 ± 0.0006 eV. Numerous unexpected vibrational excitations are observed in the photoelectron spectra due to the Jahn-Teller effect in C{sub 60}{sup −} and Hertzberg-Teller vibronic coupling in both C{sub 60}{sup −} and C{sub 60}. Both the relative intensities of vibrational peaks and their photoelectron angular distributions provide evidence for the vibronic couplings. The observed p-wave-like behavior in the angular distribution of the 0{sub 0}{sup 0} transition suggests that the electron is detached from an s-type orbital.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Vibration Reduction of Helicopter Blade Using Variable Dampers: A Feasibility Study

In the report, the investigation of controlling helicopter-blade lead-lag vibration is described. Current practice of adding passive damping may be improved to handle large dynamic range of the blade with several peaks of vibration resonance. To minimize extra-large damping forces that may damage the control system of blade, passive dampers should have relatively small damping coefficients, which in turn limit the effectiveness. By providing variable damping, a much larger damping coefficient to suppress the vibration can be realized. If the damping force reaches the maximum allowed threshold, the damper will be automatically switched into the mode with smaller damping coefficient to maintain near-constant damping force. Furthermore, the proposed control system will also have a fail-safe feature to guarantee the basic performation of a typical passive damper. The proposed control strategy to avoid resonant regions in the frequency domain is to generate variable damping force in combination with the supporting stiffness to manipulate the restoring force and conservative energy of the controlled blade system. Two control algorithms are developed and verified by a prototype variable damper, a digital controller and corresponding algorithms. Primary experiments show good potentials for the proposed variable damper: about 66% and 82% reductions in displacement at 1/3 length and the root of the blade respectively.

Lee, George C.↗

One-way coupled simulation of FIV in a 7-pin wire-wrapped fuel pin bundle

A normal fuel geometry found in sodium cooled reactor designs is the hexagonal lattice of wire-wrapped fuel pins. The wire-wrappers, which replace the more common spacer grids, act as a spacer between the fuel pins, while simultaneously increasing the fluid mixing between subchannels. The induced transverse flow, while good for mixing, increases the force load experienced by the fuel pins, increasing the possibility of problematic flow induced vibrations. The primary source of vibrations is turbulent buffeting, so very small in amplitude, but capable of rupturing the fuel cladding by fretting. The vast majority of research on fretting has been for bare rods with spacer grids. There are several significant ways that wire-wrapped fuel pins differ from bare rods that may have significant impact on the vibrations present. The increased transverse flow and asymmetrical flow pattern may result in larger and imbalanced force loads on the pins. The helical bracing of each pin may result in unique vibration patterns, and gaps may form between pins affecting how they are braced. Simulation allows for the observation of the forces present, how the flow field affects these forces, and how the structure responds and can be repeated for multiple cases for relatively low cost. Here, simulation of the flow induced vibrations for a 7-pin wire-wrapped fuel pin bundle is carried out by coupling Nek5000, a spectral element LES/DNS solver with DIABLO, a finite element CSM solver. The small amplitude vibrations allow for the assumption that the structure motion has negligible effect on the fluid flow, permitting the much less computationally expensive one-direction coupling. In order to gather significant force history data for the 2.63 helical pitch structure, a scheme was developed to artificially create force history from the power spectrum density of the one-pitch CFD simulation forces. The vibrations could then be simulated in the structure multiple times varying the contact and gaps between various pins. This provides for the search of worst-case scenarios and informs about the types of fretting that might be present. The simulation geometry is based on an experiment for comparison. However, the viscosity of the simulation was increased by a factor of four to make the simulation computationally feasible. While validation is not possible, comparisons are still valuable.

42 ENGINEERING↗

Effectiveness of Versalink 143 on Improving Shock Survival of Encapsulated Electronics

In the past, test-vehicle-mounted instrumentation modules that record sensor data during shock and vibration events have been coated with a polymer isolation layer to enhance survivability. This study uses finite element modeling to evaluate the effectiveness of the isolation material Versalink 143 on reducing stress in an instrumentation module. The modeling shows that while the isolation layer does attenuate stress due to high frequency shock and vibration, it also amplifies stress due to lower frequency shock and vibration. Thicker layers tend to attenuate high frequency stress more and amplify low frequency stress less. In addition, at higher test temperatures thermal expansion of the isolation layer can cause static stress in the module far greater than the stress due to shock, depending on how the module is constrained within the test vehicle. When designing and implementing vehicle- mounted instrumentation modules, the expected input shock spectrum, mounting constraints, and static effects of temperature must be carefully considered.

42 ENGINEERING↗

Modeling and Fabrication of IR Photonic Devices for Plasmon-Mediated Catalysis and Sensor Applications

Sandia National Laboratories (SNL) and Southwest Research Institute (SWRI) collaborated on this CRADA to explore novel 3-D metamaterial structures or devices that are proficient at eliciting surface plasmon-polaritons at infrared (IR) frequencies. The derived structures play a central role in answering fundamental questions pertaining to the vibrational coupling of molecules with surface plasmons and the potential binding interactions or catalytic effects that result from this coupling. Three-D metamaterial samples fabricated at SNL were characterized by SWRI, showing potential utility for binding molecules with similar vibrational frequencies that match the plasmon-polaritons of the metamaterial structure.

36 MATERIALS SCIENCE↗

Concepts for a theoretical and experimental study of lifting rotor random loads and vibrations. Phase 5B: Analysis of gust alleviation methods and rotor dynamic stability

The effects of various gust alleviation methods on the random blade response in flapping were studied analytically, assuming a rigid rotor support. The analytical model assumes rigid flapping blades with elastic root restraints. Linearized equations which are approximately valid at low lift conditions were used. Because of the interblade coupling from the feedback devices, the method of multiblade generalized coordinates was most convenient and was extended to include coning, differential coning, and warping of the rotor. The numerical examples cover the dynamic stability characteristics as affected by feedback gains of three- to six-bladed rotors. The number of blades had large effects on stability limits and modal time functions at these limits. The random flapping response of the blades to atmospheric turbulence was determined at 1.6 rotor advance ratio using feedback gains below the stability limit. The most effective reduction of the flapping response per unit gain was achieved with a rotor coning angle feedback.

Hohenemser, K. H.↗

Study of effects of design details on structural response to acoustic excitation

The normal mode vibration characteristics of one-dimensional and two-dimensional panel arrays were investigated analytically and experimentally. The finite element displacement method was used to formulate the structural models. The structural models include a stiffness and consistent mass matrix for thin-walled open-section beams not previously reported, and a modification of a rectangular plate bending element to include a fundamental interior mode for the element as a generalized coordinate. Provision for adding lumped masses to represent accelerometers is also included. For the one-dimensional panel, the normal mode stress resultants are obtained by integrating the equilibrium equations directly. For the two-dimensional panel arrays, the solution for the stress resultants in the cover sheet was attempted by introducing stress functions dependent upon the displacement field of the plate element. This approach, although incomplete, is a natural extension of the one-dimensional analysis for plate elements. The exerimental program which was used to verify the analysis is described and experimental results are compared with the analysis.

Rudder, F. F., Jr.↗