Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THRUST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Cathode effects on thrust subsystem performance predictability.

Development of a model of mercury vapor electron bombardment thrustor hollow cathode operation. The proposed model predicts that the primary electron emission mechanism is thermionic when sufficient low work function material is present, that the cathode is heated by power extracted from the plasma to a temperature sufficient to emit the current demanded by the external circuit; that for a given total arc current, attempts to reduce cathode temperature by changes in the external thermal coupling will affect only the amount of power extracted from the plasma; and that depletion of low work function material in the cathode results in higher cathode temperature.

Goldstein, R.↗

Low thrust propulsion system effects on communication satellites.

Choice of type and placement of thrusters on spacecraft (s/c) should include consideration of their effects on other subsystems. Models are presented of the exhaust plumes of mercury, cesium, colloid, hydrazine, ammonia, and Teflon rockets. Effects arising from plume impingement on s/c surfaces, radio frequency interference, optical interference, and earth environmental contamination are discussed. Some constraints arise in the placement of mercury, cesium, and Teflon thrusters. Few problems exist with other thruster types, nor is earth contamination a problem.

Hall, D. F.↗

Studies for determining rapid thrust response requirements and techniques for use in a long range transport aircraft

Propulsion systems proposed for the next generation of long-range transport aircraft will utilize advanced technology to reduce the noise to levels that will be inoffensive to the community. Additional reductions can be realized by adopting steeper glide slopes during the landing approach. The aircraft dynamic characteristics and methods of obtaining rapid engine response during the go-around maneuver from an aborted landing approach are identified and discussed. The study concludes that the present levels of flight safety will not be compromised by the steeper approach.

Newirth, D. M.↗

Thrust and pumping characteristics of cylindrical ejectors using afterburning turbojet gas generator

Static tests of cylindrical ejectors having ejector to primary diameter ratios from 1.1 to 1.6 and ejector length to primary nozzle diameter ratios from 0.9 to 2.1 are reported. Power setting of the J85-13 turbojet engine was varied from part power to maximum afterburning. Corrected secondary weight flow ratio was varied from 0.02 to 0.08 over a range of exhaust nozzle pressure ratios from 2.0 to 9.0. Secondary flow temperature rise and pressure drop characteristics through the nacelle secondary flow passage were also obtained.

Samanich, N. E.↗

Omni-axis secondary injection thrust vector control system

The concept, development, design study and preliminary analysis and layout of the required digital logic scheme to be used for injection valve control are presented. An application and optimization study of an Omni-Axis Secondary Injection Control System applicable to the proposed Space Shuttle Pressure Fed Engine is reported. Technical definition and analysis control procedures and test routines, as well as a supporting set of drawing sketches and reference manual, are enclosed.

Kirkley, D. J.↗

Structural technologies - Systems challenges and NASA thrusts.

Some significant areas of emphasis in the NASA airframes structures program are highlighted. The topics treated include automated analysis and design processes, building confidence in advanced composites, improving the technology base for future supersonic and hypersonic vehicles, validation of concepts for active control systems, development of predictive methods for aircraft loads and aeroelasticity, and generation of methodology to assure structural integrity as a part of the design process. An integrated long-range program for fatigue and fracture is recommended.

Brooks, G. W.↗

Reversed cowl-flap thrust augmentor

Inlet mouthpiece with variable geometry improves low-speed performance of inlet (or ejector) of jet engines by use of reversed cowl-flap mechanism. Flaps can be adjusted mechanically or system can be operated with pressure taps set so pressure on inlet face is always smaller than pressure on back of inlet.

Cheng, D. Y.↗

A preliminary design and implementation of the low-thrust simulation and trajectory search program (LOWTRAJ)

The results are presented of one phase of research conducted for the JPL Solar Electric Propulsion (SEP) Navigation Software System development program. It deals only with the problem of designing the flight quality trajectory program, which is a major subset of the entire navigation software system. In this phase of research (breadboard development phase), attempts were made to assess the SEP trajectory software functional requirements, to investigate the program design method satisfying these requirements, to identify the primary anticipated problem areas, and to provide solutions to these problem areas. These efforts culminated in the development of a compact breadboard program. A functional description and the mathematical formulation of the program are presented.

Yen, C. L.↗

Evaluation of a series hybird thrust bearing at DN values to three million. 1: Analysis and design

The analysis and design are presented of a hybrid bearing consisting of a 150-mm ball bearing and a centrifugally actuated, conical, fluid film bearing fitting an envelope with an outer radius of 86.4 mm (3.4 in.) and an inner radius of 71 mm (2.8 in.). The bearing analysis, combined with available torque data on ball bearings, indicates that an effective speed split between the ball and fluid-film bearings of 50 percent may be expected during operation at 20,000 rpm and under an axial load of 17,800 newtons (4000 lbs.). This speed split can result in a ten-fold increase in the life of the ball bearing when compared to a simple ball bearing system operating under similar conditions.

Gu, A.↗

Experimental hingeless rotor characteristics at low advance ratio with thrust

An experimental investigation to determine the dynamic characteristics of a hingeless rotor operating at moderate to high lift was conducted on a small scale, 7.5-foot diameter, four-bladed hingeless rotor model in a 7 x 10-foot wind tunnel. The primary objective of this research program was the empirical determination of the rotor steady-state and frequency responses to swashplate and body excitations. Collective pitch was set from 0 to 20 degrees, with the setting at a particular advance ratio limited by the cyclic pitch available for hub moment trim. Advance ratio varied from 0.00 to 0.36 for blades with nondimensional first-flap frequencies at 1.15, 1.28 and 1.33 times the rotor rotation frequency. Several conditions were run with the rotor operating in the transition regime. Rotor response at high lift is shown to be generally nonlinear in this region. As a secondary objective an experimental investigation of the rotor response to 4/revolution swashplate excitations at advance ratios of 0.2 to 0.85 and at a nondimensional, first-flap modal frequency of 1.34 was also conducted, using the 7 x 10-foot wind tunnel. It is shown that 4/revolution swashplate inputs are a method for substantially reducing rotor-induced, shafttransmitted vibratory forces.

London, R. J.↗

Results from cascade thrust reverser noise and suppression experiments

Results from experimental work on model scale cascade reversers with cold airflow are presented. Sound power level directivity and spectral characteristics for cascade reversers are reported. Effect of cascade exit area ratio, vane profile shape, and emission arc are discussed. Model equivalent diameters varied from 3 to 5 inches, pressure ratios range from 1.15 to 3.0. Depending on the reverser type, acoustic power was proportional to the 4 1/2 to 6th power of ideal jet velocity. Reverser noise peaked at higher frequency and was more omnidirectional than nozzle-alone jet noise. Appreciable reduction in sideline noise was obtained from plane shields. Airfoil-vaned cascades were the most aerodynamically efficient and least noisy reversers. Scaling of cascade reverser data to example aircraft engines showed all cascades above the 95 PNdB sideline goal from STOL aircraft. However, the airfoil-vaned reverser has a good potential for meeting this goal for high-bypass (low pressure ratio) exhausts.

Gutierrez, O. A.↗

Experimental investigation of combustor effects on rocket thrust chamber performance

The results are reported of a program to develop special instrumentation systems and engine hardware, conduct tests using LOX/GH2 propellants wherein radial mixtures ratio stratification was controlled, and subsequently compare the results of four selected tests with the predictions of the JANNAF performance-prediction computer programs. During the experiments, the overall propellant mixture ratio was varied from 4.4 to 6.6, while the mixture ratios in the core and outer zone were varied from 5.7 to 8.8 and from 3.7 to 7.2, respectively. A nominal 10 percent of the total fuel flow was used as boundary layer collant in a majority of the firings. Nominal chamber pressure was either 225 or 250 psia, with nozzle expansion ratios of either 25:1 or 4:1. Measurements of the axial chamber pressure and wall heat flux profiles, together with samples of the exhaust gas, were obtained. The corrected experimental specific impulse and characteristic exhaust velocity efficiencies were approximately 97.5 and 98.5 percent, respectively.

Nurick, W. H.↗

Evaluation of cermet materials suitable for lithium lubricated thrust bearings for high temperature operation

Cerment materials (HfC - 10 wt% W; HfC - 10 wt% TaC - 10 wt%W; HfC - 2 wt% CbC - 8 wt% Mo;Hfn - 10 wt% W; Hfn - 10 wt% TaN - 10 wt% W; and ZrC - 17 wt% W) were evaluated for possible use as lithium-lubricated bearings in the control system of a nuclear reactor. Tests of compatibility with lithium were made in T-111 (Ta-8W-2Hf) capsules at temperatures up to 1090 C. The tendencies of HfC-TaC-W, HfC-CbC-Mo, and HfN-W to bond to themselves and to the refractory alloys T-111 and TZM when enclosed in lithium-filled capsules under a pressure of 2000 psi at 980 and 1200 C for 1933 hours were evaluated. Thermal expansion characteristics were determined for the same three materials from room temperature to 1200 C. On the basis of these tests, HfC-10 TaC-10W and HfN-10W were selected as the best and second best candidates, respectively, of the materials tested for the bearing application.

Sinclair, J. H.↗

Space shuttle orbit maneuvering engine reusable thrust chamber: Adverse operating conditions test report

Test hardware, facilities, and procedures are described along with results of electrically heated tube and channel tests conducted to determine adverse operating condition limits for convectively cooled chambers typical of Space Shuttle Orbit Manuevering Engine designs. Hot-start tests were conducted with corrosion resistant steel and nickel tubes with both monomethylhydrazine and 50-50 coolants. Helium ingestion, in both bubble and froth form, was studied in tubular test sections. Helium bubble ingestion and burn-out limits in rectangular channels were also investigated.

Tobin, R. D.↗

Thrust-isolating mounting

A supporting frame for a load, such as one or more telescopes, is isolated from all multi-gravitational forces, which will be developed within that load as that load is propelled into space, by using a shroud to fully and solidly hold that load until that load has been propelled into space. Thereafter, that shroud will be jettisoned; and then supports which are on, and which are movable with, that load will have surfaces thereon moved into supporting engagement with complementary surfaces on that supporting frame to enable that supporting frame and those supports to fully and solidly hold that load.

Wetzler, D. G.↗