Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Optimum design of antireflection coating for silicon solar cells

Based on classical electromagnetic theory, reflectivity calculations for various single and double optical coating systems for silicon solar cells are presented. From calculations and considerations of solar spectral response of the solar cells, the number and thickness of coating materials needed to obtain efficient solar cells can be predicted. Some experimental results on single layer coated cells are also presented for comparison with calculations, and agreement is good. By means of microwave transmission line analogy, the design of the multilayer coating can be simplified by using Tchebycheff polynomials.

Wang, E. Y.↗

Efficiency improved by acid texturization for multi-crystalline silicon solar cells

In this paper, we will show that efficiency of multi-crystalline silicon (mc-Si) solar cells may be improved by acid texturization. In order to enhance overall efficiency of mc-Si for solar-cell applications, the surface treatment of texturization with wet etching using appropriate solutions can improve incident light into the cell. Alkali etchant cannot produce uniformly textured surface to generate enough open circuit voltage (V{sub OC}) and high efficiency of the mc-Si due to the unavoidable grain randomly oriented with higher steps formed during etching process. Optimized acid etching conditions can be obtained by decreasing the reflectance (R) for mc-Si substrate below levels generated by alkali etching. Short-circuit current (I{sub SC}) measurements on acid textured cells reveal that current gain can be significantly enhanced by reducing reflection. The optimal acid etching ratio HF:HNO{sub 3}:H{sub 2}O = 15:1:2.5 with etching time of 60 s and lowering 42.7% of the R value can improve 112.4% of the conversion efficiency ({eta}) of the developed solar cell. In order to obtain more detailed information of different defect region, high-resolution light beam induced current (LBIC) is applied to measure the internal quantum efficiency (IQE) and the lifetime of minority carriers. Thus, the acid texturing approach is instrumental to achieve high efficiency in mass production using relatively low-cost mc-Si as starting material with proper optimization of the fabrication steps. (author)

14 SOLAR ENERGY↗

Deep Absorbing Porphyrin Small Molecule for High-Performance Organic Solar Cells with Very Low Energy Losses

In this work, we designed and synthesized the DPPEZnP-TEH molecule, with a porphyrin ring linked to two diketopyrrolopyrrole units by ethynylene bridges. The resulting material exhibits a very low energy band gap of 1.37 eV and a broad light absorption to 907 nm. An open-circuit voltage of 0.78 V was obtained in bulk heterojunction (BHJ) organic solar cells, showing a low energy loss of only 0.59 eV, which is the first report that small molecule solar cells show energy losses <0.6 eV. The optimized solar cells show remarkable external quantum efficiency, short circuit current, and power conversion efficiency up to 65%, 16.76 mA/cm 2 , and 8.08%, respectively, which are the best values for BHJ solar cells with very low energy losses. Additionally, the morphology of DPPEZnP-TEH neat and blend films with PC61BM was studied thoroughly by grazing incidence X-ray diffraction, resonant soft X-ray scattering, and transmission electron microscopy under different fabrication conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improved Transparent Conducting Oxides Boost Performance of Thin-Film Solar Cells (Fact Sheet)

Today?s thin-film solar cells could not function without transparent conducting oxides (TCOs). TCOs act as a window, both protecting the cell and allowing light to pass through to the cell?s active layers. Until recently, TCOs were seen as a necessary, but static, layer of a thin-film photovoltaic (PV) cell. But a group of researchers at the National Renewable Energy Laboratory (NREL) has identified a pathway to producing improved TCO films that demonstrate higher infrared transparency. To do so, they have modified the TCOs in ways that did not seem possible a few years ago.

14 SOLAR ENERGY↗

Study of minority carrier diffusion lengths in photoactive layers of multijunction solar cells

A technique for determining a minority carrier's diffusion length in photoactive III-V layers of solar cells by approximating their spectral characteristics is presented. Single-junction GaAs, Ge and multi-junction GaAs/Ge, GaInP/GaAs, and GaInP/GaInAs/Ge solar cells fabricated by hydride metal-organic vapor-phase epitaxy (H-MOVPE) have been studied. The dependences of the minority carrier diffusion length on the doping level of p-Ge and n-GaAs are determined. It is shown that the parameters of solid-state diffusion of phosphorus atoms to the p-Ge substrate from the n-GaInP nucleation layer are independent of the thickness of the latter within 35-300 nm. It is found that the diffusion length of subcells of multijunction structures in Ga(In)As layers is smaller in comparison with that of single-junction structures.

36 MATERIALS SCIENCE↗

Endurance testing of first generation (Block 1) commercial solar cell modules

To determine lifetimes of the first generation (Block 1) commercial solar cell modules used in solar cell arrays, a program was initiated to expose these modules to a range of environments. The conditions endured by these modules encompassed hot and dry, hot and humid, tropical rain forests, sea-air, urban industrial and urban clean. Exposures were for periods up to 1 year. The effect of outdoor exposure on the performance of the modules was determined using current-voltage curves. Short-circuit current (I sub sc) and maximum power (P sub max) were the parameters monitored. In all cases, there was a loss of performance of the modules with outdoor exposure.

Anagnostou, E.↗

ER-2 High Altitude Solar Cell Calibration Flights

The first flights of the ER-2 solar cell calibration demonstration were conducted during September-October of 2014. Three flights were performed that not only tested out the equipment and operational procedures, but also demonstrated the capability of this unique facility by conducting the first short-circuit measurements on a variety of test solar cells. Very preliminary results of these first flights were presented at the 2014 Space Photovoltaic Research and Technology (SPRAT) Conference in Cleveland, OH shortly following these first flights. At the 2015 Space Power Workshop, a more detailed description of these first ER-2 flights will be presented, along with the final flight data from some of the test cells that were flown and has now been reduced and corrected for ER-2 atmospheric flight conditions. Plans for ER-2 flights during the summer of 2015 will also be discussed.

solar cells↗

Cu(In,Ga)S2, Thin-Film Solar Cells Prepared by H2S Sulfurization of CuGa-In Precursor

Thin-film CuInS2 solar cell is the leading candidate for space power because of bandgap near the optimum value for AM0 solar radiation outside the earth's atmosphere, excellent radiation hardness, and freedom from intrinsic degradation mechanisms unlike a-Si:H cells. Ultra-lightweight thin-film solar cells deposited on flexible polyimide plastic substrates such as Kapton(trademark), Upilex(trademark), and Apical(trademark) have a potential for achieving specific power of 1000 W/kg, while the state-of-art specific power of the present day solar cells is 66 W/kg. This paper describes the preparation of Cu-rich CuIn(sub 1-x)Ga(sub x)S(sub 2) (CIGS2) thin films and solar cells by a process of sulfurization of CuGa-In precursor similar to that being used for preparation of large-compact-grain CuIn(sub 1-x)Ga(sub x)Se2 thin films and efficient solar cells at FSEC PV Materials Lab.

Dhere, Neelkanth G.↗

Effect of ZnS, iZnO, dZnO and Cu(In,Ga)Se{sub 2} thickness on the performance of simulated Mo/Cu(In,Ga)Se{sub 2}/ZnS/iZnO/dZnO solar cell

In this paper, Mo/Cu(In,Ga)Se{sub 2}/ZnS/iZnO/dZnO solar cell is simulated and optimized by studying the effect of layers thickness on solar cell efficiency using Silvaco ATLAS software. The input simulation parameters are: dielectric permittivity (ε), band gap energy (E{sub g}), electron affinity (χ), conduction band effective density of states (N{sub c}), valence band effective density of states (N{sub v}). The output parameters used to find the optimum values of the layers thickness are the short circuit current density (I{sub sc}), open circuit voltage (V{sub oc}), maximum power (P{sub max}), fill factor (FF), efficiency (η), Current–voltage (I–V) and power–voltage (P–V) characteristics.

14 SOLAR ENERGY↗

Eco–Friendly Solvent Engineered CsPbI 2.77 Br 0.23 Ink for Large–Area and Scalable High Performance Perovskite Solar Cells

The performance of large-area perovskite solar cells (PSCs) has been assessed for typical compositions, such as methylammonium lead iodide (MAPbI 3 ), using a blade coater, slot-die coater, solution shearing, ink-jet printing, and thermal evaporation. However, the fabrication of large-area all-inorganic perovskite films is not well developed. This study develops, for the first time, an eco-friendly solvent engineered all-inorganic perovskite ink of dimethyl sulfoxide (DMSO) as a main solvent with the addition of acetonitrile (ACN), 2-methoxyethanol (2-ME), or a mixture of ACN and 2-ME to fabricate large-area CsPbI 2.77 Br 0.23 films with slot-die coater at low temperatures (40–50 °C). The perovskite phase, morphology, defect density, and optoelectrical properties of prepared with different solvent ratios are thoroughly examined and they are correlated with their respective colloidal size distribution and solar cell performance. Here, the optimized slot-die-coated CsPbI 2.77 Br 0.23 perovskite film, which is prepared from the eco-friendly binary solvents dimethyl sulfoxide:acetonitrile (0.8:0.2 v/v), demonstrates an impressive power conversion efficiency (PCE) of 19.05%. Moreover, the device maintains ≈91% of its original PCE after 1 month at 20% relative humidity in the dark. It is believed that this study will accelerate the reliable manufacturing of perovskite devices.

binary and ternary solvent↗

Radiation damage and defect behavior in proton irradiated lithium-counterdoped n+p silicon solar cells

Two lithium-counterdoped n+p silicon solar cells with different lithium concentrations were irradiated by 10-MeV protons. Cell performance was measured as a function of fluence, and it was found that the cell with the highest concentration of lithium had the highest radiation resistance. Deep level transient spectroscopy which showed two deep level defects that were lithium related. Relating the defect energy levels obtained from this study with those from earlier work using 1-MeV electron irradiation shows no correlation of the defect energy levels. There is one marked similarity: the absence of the boron-interstitial-oxygen-interstitial defect. This consistency strengthens the belief that lithium interacts with oxygen to prevent the formation of the boron interstitial-oxygen interstitial defect. The results indicate that, in general, addition of lithium in small amounts to the p-base of a boron doped silicon solar cell such that the base remains p-type, tends to increase the radiation resistance of the cell.

Stupica, John↗

Balance on the charge generation, separation and transfer performance of different TiO{sub 2} nanostructures in quantum dot sensitized solar cells

Graphical abstract: QDSSCs with different structure: (a) J-V curves, (b) TRPL spectra. - Highlights: • Charge generation, separation and transfer performance have been balanced by different structures. • Excellent charge separation and transfer performance have been exhibited for nano-array structure. • Nanotube array structure relative better charge generation, excellent charge separation and transfer performance of QDSSCs. - Abstract: TiO{sub 2} nanoparticle and nano-array structures including nanorods, nanowires and nanotubes are prepared for the photo-electrodes of CuInS{sub 2} quantum dot sensitized solar cells, which are investigated the balance on charge generation, separation and transfer performance in solar cells. The optical absorption properties and PL spectra of different photo-electrodes are investigated, which indicates better charge generation property for nanoparticle structure and better charge separation property for nano-arrays structure. With the grain boundary of nanoparticle films and excellent charge transfer performance of nano-arrays films, higher short-circuit current density value has been performed for all the nano-array structure based solar cells. Due to the relative large surface area of three nano-arrays structure for charge generation, excellent charge separation and transfer performance, the TiO{sub 2} nanotube based CuInS{sub 2} quantum dot sensitized solar cells exhibits greater photovoltaic efficiency than other nanostructures, which can support the progress for further photovoltaic performance enhancement on quantum dot sensitized solar cells.

36 MATERIALS SCIENCE↗

Estimation of the potential efficiency of a multijunction solar cell at a limit balance of photogenerated currents

A method is proposed for estimating the potential efficiency which can be achieved in an initially unbalanced multijunction solar cell by the mutual convergence of photogenerated currents: to extract this current from a relatively narrow band-gap cell and to add it to a relatively wide-gap cell. It is already known that the properties facilitating relative convergence are inherent to such objects as bound excitons, quantum dots, donor-acceptor pairs, and others located in relatively wide-gap cells. In fact, the proposed method is reduced to the problem of obtaining such a required light current-voltage (I–V) characteristic which corresponds to the equality of all photogenerated short-circuit currents. Two methods for obtaining the required light I–V characteristic are used. The first one is selection of the spectral composition of the radiation incident on the multijunction solar cell from an illuminator. The second method is a double shift of the dark I–V characteristic: a current shift J{sub g} (common set photogenerated current) and a voltage shift (−J{sub g}R{sub s}), where R{sub s} is the series resistance. For the light and dark I–V characteristics, a general analytical expression is derived, which considers the effect of so-called luminescence coupling in multijunction solar cells. The experimental I–V characteristics are compared with the calculated ones for a three-junction InGaP/GaAs/Ge solar cell with R{sub s} = 0.019 Ω cm{sup 2} and a maximum factual efficiency of 36.9%. Its maximum potential efficiency is estimated as 41.2%.

36 MATERIALS SCIENCE↗

Energy Yield Determination of Concentrator Solar Cells using Laboratory Measurements: Preprint

The annual energy conversion efficiency is calculated for a four junction inverted metamorphic solar cell that has been completely characterized in the laboratory at room temperature using measurements fit to a comprehensive optoelectronic model of the multijunction solar cells. A simple model of the temperature dependence is used to predict the performance of the solar cell under varying temperature and spectra characteristic of Golden, CO for an entire year. The annual energy conversion efficiency is calculated by integrating the predicted cell performance over the entire year. The effects of geometric concentration, CPV system thermal characteristics, and luminescent coupling are highlighted. temperature and spectra characteristic of Golden, CO for an entire year. The annual energy conversion efficiency is calculated by integrating the predicted cell performance over the entire year. The effects of geometric concentration, CPV system thermal characteristics, and luminescent coupling are highlighted.

14 SOLAR ENERGY↗

Transient electrically detected magnetic resonance spectroscopy applied to organic solar cells

The influence of light-induced paramagnetic states on the photocurrent generated by polymer:fullerene solar cells is studied using spin-sensitive techniques in combination with laser-flash excitation. For this purpose, we developed a setup that allows for simultaneous detection of transient electron paramagnetic resonance as well as transient electrically detected magnetic resonance (trEDMR) signals from fully processed and encapsulated solar cells. Combining both techniques provides a direct link between photoinduced triplet excitons, charge transfer states, and free charge carriers as well as their influence on the photocurrent generated by organic photovoltaic devices. Our results obtained from solar cells based on poly(3-hexylthiophene) as electron donor and a fullerene-based electron acceptor show that the resonant signals observed in low-temperature (T = 80 K) trEDMR spectra can be attributed to positive polarons in the polymer as well as negative polarons in the fullerene phase, indicating that both centers are involved in spin-dependent processes that directly influence the photocurrent.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A PL and PLE Study of High Cu Content Cu{sub 2}ZnSnSe{sub 4} Films on Mo/Glass and Solar Cells

Cu{sub 2}ZnSnSe{sub 4} (CZTSe) is amongst leading candidates for the absorber layer in sustainable solar cells. We examine CZTSe thin films with [Cu]/[Zn + Sn] of 0.99 and [Zn]/[Sn] of 1.07, deposited on Mo/glass substrates, and solar cells fabricated from these films. The bandgap (E{sub g}) of the as deposited films and solar cells was examined by photoluminescence excitation (PLE) whereas the temperature and excitation intensity dependence of photoluminescence (PL) spectra was used to examine the nature of radiative recombination. The 6 K PL spectra of CZTSe/Mo exhibit an intense broad and asymmetrical band P1 at 0.822 eV and a lower intensity band P2 at 0.93 eV. The shape of this band, high rates of blue shift with excitation intensity rise ( j-shift) j(P1) = 14 meV and j(P2) = 8 meV per decade, and red shifts of both bands with increasing temperature suggest that both bands are associated with valence band tails due to potential fluctuations caused by high populations of charged defects. The mean depth of such fluctuation γ of 24 meV was estimated from the low energy side of P1. Device processing increased E{sub g}, blue shifted P1, decreased its width, j-shift and the mean depth of potential fluctuations. These can be due to the annealing and/or can partly be related to KCN etching and the chemical effect of Cd, from CdS replacing copper at the CdS–CZTSe interface layer. Processing induced a new broad band P3 at 1.3 eV (quenching with E{sub a} = 200 meV). We attributed P3 to defects in the CdS layer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The effect of microscopic texture on the direct plasma surface passivation of Si solar cells

Textured silicon surfaces are widely used in manufacturing of solar cells due to increasing the light absorption probability and also the antireflection properties. However, these Si surfaces have a high density of surface defects that need to be passivated. In this study, the effect of the microscopic surface texture on the plasma surface passivation of solar cells is investigated. The movement of 10{sup 5} H{sup +} ions in the texture-modified plasma sheath is studied by Monte Carlo numerical simulation. The hydrogen ions are driven by the combined electric field of the plasma sheath and the textured surface. The ion dynamics is simulated, and the relative ion distribution over the textured substrate is presented. This distribution can be used to interpret the quality of the Si dangling bonds saturation and consequently, the direct plasma surface passivation.

36 MATERIALS SCIENCE↗