Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Effects of Combined Stressing on the Electrical Properties of Film and Ceramic Capacitors

Advanced power systems which generate, control, and distribute electrical power to many large loads are a requirement for future space exploration missions. The development of high temperature insulating materials and power components constitute a key element in systems which are lightweight, efficient, and are capable of surviving the hostile space environment. In previous work, experiments were carried out to evaluate film and ceramic capacitors for potential use in high temperature applications. The effects of thermal stressing, in air and without electrical bias, on the electrical properties of the capacitors as a function of thermal aging up to 12 weeks were determined. In this work, the combined effects of thermal aging and electrical stresses on the properties of teflon film and ceramic power capacitors were examined. The ceramic capacitors were thermally aged for 35 weeks and the teflon capacitors for 15 weeks at 200 C under full electrical bias and were characterized, on a weekly basis, in terms of their capacitance stability and electrical loss in the frequency range of 50 Hz to 100 kHz. DC leakage current measurements were also obtained. The results obtained represent the influence that short-term thermal aging and electrical bias have on the electrical properties of the power capacitors characterized.

Overton, Eric↗

Prediction of thermal and mechanical stress-strain responses of TMC's subjected to complex TMF histories

This paper presents an experimental and analytical evaluation of cross-plied laminates of Ti-15V-3Cr-3Al-3Sn (Ti-15-3) matrix reinforced with continuous silicon-carbide fibers (SCS-6) subjected to a complex TMF loading profile. Thermomechanical fatigue test techniques were developed to conduct a simulation of a generic hypersonic flight profile. A micromechanical analysis was used. The analysis predicts the stress-strain response of the laminate and of the constituents in each ply during thermal and mechanical cycling by using only constituent properties as input. The fiber was modeled as elastic with transverse orthotropic and temperature-dependent properties. The matrix was modeled using a thermoviscoplastic constitutive relation. The fiber transverse modulus was reduced in the analysis to simulate the fiber-matrix interface failures. Excellent correlation was found between measured and predicted laminate stress-strain response due to generic hypersonic flight profile when fiber debonding was modeled.

Johnson, W. S.↗

A New Reynolds Stress Algebraic Equation Model

A general turbulent constitutive relation is directly applied to propose a new Reynolds stress algebraic equation model. In the development of this model, the constraints based on rapid distortion theory and realizability (i.e. the positivity of the normal Reynolds stresses and the Schwarz' inequality between turbulent velocity correlations) are imposed. Model coefficients are calibrated using well-studied basic flows such as homogeneous shear flow and the surface flow in the inertial sublayer. The performance of this model is then tested in complex turbulent flows including the separated flow over a backward-facing step and the flow in a confined jet. The calculation results are encouraging and point to the success of the present model in modeling turbulent flows with complex geometries.

Shih, Tsan-Hsing↗

Probabilistic Simulation of Stress Concentration in Composite Laminates

A computational methodology is described to probabilistically simulate the stress concentration factors (SCF's) in composite laminates. This new approach consists of coupling probabilistic composite mechanics with probabilistic finite element structural analysis. The composite mechanics is used to probabilistically describe all the uncertainties inherent in composite material properties, whereas the finite element is used to probabilistically describe the uncertainties associated with methods to experimentally evaluate SCF's, such as loads, geometry, and supports. The effectiveness of the methodology is demonstrated by using is to simulate the SCF's in three different composite laminates. Simulated results match experimental data for probability density and for cumulative distribution functions. The sensitivity factors indicate that the SCF's are influenced by local stiffness variables, by load eccentricities, and by initial stress fields.

Chamis, C. C.↗

Stress intensity factors for surface and corner cracks emanating from a wedge-loaded hole

To assist analysis of riveted lap joints, stress intensity factors are determined for surface and corner cracks emanating from a wedge-loaded hole by using a 3-D weight function method in conjunction with a 3-D finite element method. A stress intensity factor equation for surface cracks is also developed to provide a closed-form solution. The equation covers commonly-encountered geometrical ranges and retains high accuracy over the entire range.

Zhao, W.↗

A review of Reynolds stress models for turbulent shear flows

A detailed review of recent developments in Reynolds stress modeling for incompressible turbulent shear flows is provided. The mathematical foundations of both two-equation models and full second-order closures are explored in depth. It is shown how these models can be systematically derived for two-dimensional mean turbulent flows that are close to equilibrium. A variety of examples are provided to demonstrate how well properly calibrated versions of these models perform for such flows. However, substantial problems remain for the description of more complex turbulent flows where there are large departures from equilibrium. Recent efforts to extend Reynolds stress models to nonequilibrium turbulent flows are discussed briefly along with the major modeling issues relevant to practical naval hydrodynamics applications.

Speziale, Charles G.↗

On the thermally-induced residual stresses in thick fiber-thermoplastic matrix (PEEK) cross-ply laminated plates

An analytical method for calculating thermally-induced residual stresses in laminated plates is applied to cross-ply PEEK laminates. We considered three cooling procedures: slow cooling (uniform temperature distribution); convective and radiative cooling; and rapid cooling by quenching (constant surface temperature). Some of the calculated stresses are of sufficient magnitude to effect failure properties such as matrix microcracking.

Hu, Shoufeng↗

Stress relaxation of low pressure plasma-sprayed NiCrAlY alloys

The stress relaxation behavior of three NiCrAlY alloys that are commonly used as bond coats for thermal barrier coatings (TBCs) has been directly measured. The relaxation study was conducted at temperatures of 800-1000 C and over a wide range of stresses. It was established that all three bond coat alloys relaxed quite rapidly at temperatures of 900 C and above. Since the upper use temperatures for bond coats in gas turbine engines are between 900 and 1000 C, bond coat relaxation is expected to occur in service. Therefore, relaxation of the bond coat has the potential to affect TBC life. Furthermore, the relaxation differences observed between the three alloys offers a possible explanation for the differences in TBC life observed for these bond coats. While bond coat relaxation is expected to occur for a TBC in service, the mechanism for a relaxation effect on TBC life, if it exists, is yet to be determined.

Brindley, W. J.↗

Wrinkle ridges, stress domains, and kinematics of venusian plains

Wrinkle ridges are nearly ubiquitous landforms on the plains of Venus. By analogy with similar structures on other planets, venusian wrinkle ridges are inferred to trend normal to the direction of maximum principal compression in the crust, an inference that is verified by geometrical relationships with positive and negative relief features on Venus. Because plains are the dominant terrain on Venus, wrinkle ridges provide an excellent opportunity to determine the orientations of shallow crustal principal stress trajectories over most of the planet. In most places there are two or more sets of wrinkle ridges, and commonly one of these persists over a large area, defining a regional stress domain. Intersection relationships indicate that these domains differ in age.

Mcgill, George E.↗

Gravity gradient or gravity jitter induced viscous stress and moment fluctuations in microgravity

The dynamical behavior of fluids affected by the asymmetric gravity gradient and gravity jitter accelerations, in particular the effect of surface tension on partially-filled rotating fluids with a special example applicable to a full-scale Gravity Probe-B Spacecraft dewar tank, has been investigated. Results of slosh wave excitation along the liquid-vapor interface induced by gravity gradient acceleration indicated one-up one-down and one-down and one-up oscillations of two bubbles in the cross-section of doughnut profiles in the vertical r-z plane of a rotating dewar, and an eccentric contour of a bubble rotating around the axis of the dewar in the horizontal r-theta plane. Results of slosh wave excitation along the liquid-vapor interface induced by gravity jitter acceleration showed an equivalent to the time-dependent oscillatory force which pushes a bubble in the combined bubble motion of down-and-up and leftward-and-rightward as the bubble is rotating with respect to a rotating dewar axis. Fluctuations of fluid stress forces, fluid stress moments, and moment arm of fluid moment exerted on the dewar wall of the container due to slosh wave excitations driven by gravity gradient acceleration or gravity jitter acceleration are also investigated.

Hung, R. J.↗

Scanning electron acoustic microscopy of residual stresses in ceramics: Theory and experiment

Several reviews have highlighted a number of applications of scanning electron acoustic microscopy (SEAM) to metals and semiconductors which show that SEAM can provide new information on surface and near-surface features of such materials, but there have been few studies attempting to determine the capabilities of SEAM for characterizing ceramic materials. We have recently observed image contrast in SEAM from residual stress fields induced in brittle materials by Vickers indentations that is strongly dependent on the electron beam chopping frequency. We have also recently developed a three-dimensional mathematical model of signal generation and contrast in SEAM, appropriate to the brittle materials studied, that we use as a starting point in this paper for modeling the effect of residual stress fields on the generated electron acoustic signal. The influence of the electron beam chopping frequency is also considered under restrictive assumptions.

Cantrell, John H.↗

Computing Contact Stresses In Gear Teeth

Improved method of computing contact stresses in gear teeth accounts for complicating effects like those of static and sliding friction. Provides iterative procedure for determination of contact region and nodal contact forces along with contact stresses. Method based on equations and computational procedure incorporating these effects routinely.

Oswald, Fred B.↗

Analysis of surface cracks at hole by a 3-D weight function method with stresses from finite element method

Parallel with the work in Part-1, stress intensity factors for semi-elliptical surface cracks emanating from a circular hole are determined. The 3-D weight function method with the 3D finite element solutions for the uncracked stress distribution as in Part-1 is used for the analysis. Two different loading conditions, i.e. remote tension and wedge loading, are considered for a wide range in geometrical parameters. Both single and double surface cracks are studied and compared with other solutions available in the literature. Typical crack opening displacements are also provided.

Zhao, W.↗

Stress and Damage in Polymer Matrix Composite Materials Due to Material Degradation at High Temperatures

This report describes analytical methods for calculating stresses and damage caused by degradation of the matrix constituent in polymer matrix composite materials. Laminate geometry, material properties, and matrix degradation states are specified as functions of position and time. Matrix shrinkage and property changes are modeled as functions of the degradation states. The model is incorporated into an existing composite mechanics computer code. Stresses, strains, and deformations at the laminate, ply, and micro levels are calculated, and from these calculations it is determined if there is failure of any kind. The rationale for the model (based on published experimental work) is presented, its integration into the laminate analysis code is outlined, and example results are given, with comparisons to existing material and structural data. The mechanisms behind the changes in properties and in surface cracking during long-term aging of polyimide matrix composites are clarified. High-temperature-material test methods are also evaluated.

McManus, Hugh L.↗

The Lagrangian Multiplier Method of Finding Upper and Lower Limits to Critical Stresses of Clamped Plates

The theory of Lagrangian multipliers is applied to the problem of finding both upper and lower limits to the true compressive buckling stress of a clamped rectangular plate. The upper and lower limits thus bracket the truss, which cannot be exactly found by the differential-equation approach. The procedure for obtaining the upper limit, which is believed to be new, presents certain advantages over the classical Raleigh-Rite method of finding upper limits. The theory of the lower-limit procedure has been given by Trefftz but, in the present application, the method differs from that of Trefftz in a way that makes it inherently more quickly convergent. It is expected that in other buckling problems and in some vibration problems problems the Lagrangian multiplier method finding upper and lower limits may be advantageously applied to the calculation of buckling stresses and natural frequencies.

Budiansky, Bernard↗

Effects of microgravity and clinorotation on stress ethylene production in two starchless mutants of Arabidopsis thaliana

Starch filled plastids termed amyloplasts, contained within columella cells of the root caps of higher plant roots, are believed to play a statolith-like role in the gravitropic response of roots. Plants having amyloplasts containing less starch exhibit a corresponding reduction in gravitropic response. We have observed enhanced ethylene production by sweet clover (Melilotus alba L.) seedlings grown in the altered gravity condition of a slow rotating clinostat, and have suggested that this is a stress response resulting from continuous gravistimulation rather than as a result of the simulation of a microgravity condition. If so, we expect that plants deficient in starch accumulation in amyloplasts may produce less stress ethylene when grown on a clinostat. Therefore, we have grown Arabidopsis thaliana in the small, closed environment of the Fluid Processing Apparatus (FPA). In this preliminary report we compare stationary plants with clinorotated and those grown in microgravity aboard Discovery during the STS-63 flight in February 1995. In addition to wildtype, two mutants deficient in starch biosynthesis, mutants TC7 and TL25, which are, respectively, deficient in the activity of amyloplast phosphoglucomutase and ADP-glucose pyrophosphorylase, were grown for three days before being fixed within the FPA. Gas samples were aspirated from the growth chambers and carbon dioxide and ethylene concentations were measured using a gas chromatograph. The fixed tissue is currently undergoing further morphologic and microscopic characterization.

Gallegos, Gregory L.↗

Effect of microgravity on stress ethylene and carbon dioxide production in sweet clover (Melilotus alba L.)

The study of higher plant growth and development in the microgravity (micro-g) environment continues to be a challenge. This is in part a result of the available flight qualified hardware with restrictive closed gas environments. This point is underscored by considering that gas exchange of seedlings grown in microgravity may be further limited owing to a thicker layer of water wicked onto the roots and to the absence of convective mixing. We hypothesized that seedlings grown under such conditions will experience greater hypoxia in microgravity than at Earth gravity, and thus produce greater stress ethylene. We compared flight and ground samples of sweet clover seedlings grown in the Fluid Processing Apparatus (FPA) during STS-57 and found them to contain extremely high levels of carbon dioxide (CO2) and stress ethylene. There were time dependent increases for both gases, and seedling growth was greatly inhibited. We repeated these experiments aboard STS-60 using modified chambers which increased, by fifty fold, the air available to the developing seedlings. Sweet clover seed germination and subsequent seedling growth to eight days within the FPA modified with a gas permeable membrane is not compromised by the microgravity environment.

Gallegos, Gregory L.↗