Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SIDE EFFECTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Operation of a New Half-Bridge Gate Driver for Enhancement - Mode GaN FETs, Type LM5113, Over a Wide Temperature Range

A new commercial-off-the-shelf (COTS) gate driver designed to drive both the high-side and the low-side enhancement-mode GaN FETs, National Semiconductor's type LM5113, was evaluated for operation at temperatures beyond its recommended specified limits of -40 C to +125 C. The effects of limited thermal cycling under the extended test temperature, which ranged from -194 C to +150 C, on the operation of this chip as well as restart capability at the extreme cryogenic and hot temperatures were also investigated. The driver circuit was able to maintain good operation throughout the entire test regime between -194 C and +150 C without undergoing any major changes in its outputs signals and characteristics. The limited thermal cycling performed on the device also had no effect on its performance, and the driver chip was able to successfully restart at each of the extreme temperatures of -194 C and +150 C. The plastic packaging of this device was also not affected by either the short extreme temperature exposure or the limited thermal cycling. These preliminary results indicate that this new commercial-off-the-shelf (COTS) halfbridge eGaN FET driver integrated circuit has the potential for use in space exploration missions under extreme temperature environments. Further testing is planned under long-term cycling to assess the reliability of these parts and to determine their suitability for extended use in the harsh environments of space.

Patterson, Richard↗
DOE OSTI2022

Enhanced Pool Boiling of Low-Pressure Refrigerants on Round Tubes- An Experimental Evaluation

Pool boiling heat transfer is one of the most effective heat transfer methos and crucial for several energy conversion processes such as electronic cooling, steam generation, water purification and thermal management. Enhancing boiling heat transfer around the tubes enables higher heat flux, which can improve the efficiency and lead to compact heat exchangers. Delaying the onset of critical heat flux (CHF) allows for higher CHFs and protects equipment during anomalous transient conditions. Growing interest in process intensification and delayed CHF has motivated the current study. An experimental approach has been deployed to investigate a potential technique to enhance the pool boiling performance around small diameter tubes by open cell metal foams. The findings for nucleate pool boiling of Novec HFE 7000 on the externally enhanced and smooth tubes are reported. The enhanced tube comprised of compressed aluminum foam brazed around. All the samples were horizontally oriented, and the experiments were performed under ambient pressure conditions. The heat transfer measurements for the smooth tubes were compared with several existing correlations and established the baseline. The preliminary results showed that the aluminum foam effectively enhanced the heat transfer coefficient and delayed the onset of critical heat flux. In addition, the pool boiling process around the round tube sample was visualized from both side and front views to comprehend the heat transfer mechanisms underlying substantial enhancement observed during experiments.

Yang, Cheng-Min↗
DOE OSTI2024

Steam Generator Model Design Parameter Sensitivity Study Using Advanced Optimization Tools

This study focuses on design parameter sensitivity studies pertaining to a steam generator (SG) model, using both Python and machine-learning tools. The SG model is a mathematical representation (including fluid flow and heat transfer equations/models/correlations) of a steam-generating unit in a pressurized water reactor (PWR)-type small modular reactor (SMR) system. Design studies involve changing the model’s input design parameters (e.g., temperature, pressure, mass flow rate) to observe the resulting effects on the output of the system (e.g., heat transfer coefficient [HTC], Nusselt number, heat transfer performance). Sensitivity studies analyze the degree to which system output and/or desired parameters (e.g., HTC or heat transfer performance) are sensitive to changes in input parameters. By using machine-learning tools such as the Risk Analysis Virtual Environment (RAVEN) developed at Idaho National Laboratory (INL), detailed design parametric sensitivity studies and model optimization were performed. Six input parameters—namely, the pressure, temperature, and mass flow rate for the inlet of the primary-side (hot fluid) and secondary-side (cold fluid) of the SG—were randomly perturbed via RAVEN’s Monte Carlo Sampler module, using uniform distributions (±1% relative changes). The analysis results give valuable insights into SG system performance and optimization, and provide justification for researching optimized sensor placement to effectively monitor and obtain experimental data.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Steam Generator Model Design Parameter Sensitivity Study Using Advanced Optimization Tools

This study focuses on design parameter sensitivity studies pertaining to a steam generator (SG) model, using both Python and machine-learning tools. The SG model is a mathematical representation (including fluid flow and heat transfer equations/models/correlations) of a steam-generating unit in a pressurized water reactor (PWR)-type small modular reactor (SMR) system. Design studies involve changing the model’s input design parameters (e.g., temperature, pressure, mass flow rate) to observe the resulting effects on the output of the system (e.g., heat transfer coefficient [HTC], Nusselt number, heat transfer performance). Sensitivity studies analyze the degree to which system output and/or desired parameters (e.g., HTC or heat transfer performance) are sensitive to changes in input parameters. By using machine-learning tools such as the Risk Analysis Virtual Environment (RAVEN) developed at Idaho National Laboratory (INL), detailed design parametric sensitivity studies and model optimization were performed. Six input parameters—namely, the pressure, temperature, and mass flow rate for the inlet of the primary-side (hot fluid) and secondary-side (cold fluid) of the SG—were randomly perturbed via RAVEN’s Monte Carlo Sampler module, using uniform distributions (±1% relative changes). The analysis results give valuable insights into SG system performance and optimization, and provide justification for researching optimized sensor placement to effectively monitor and obtain experimental data.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1984

Wing planform effects at supersonic speeds for an advanced fighter configuration

Four advanced fighter configurations, which differed in wing planform and airfoil shape, were investigated in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.60, 1.80, 2.00, and 2.16. Supersonic data were obtained on the four uncambered wings, which were each attached to a single fighter fuselage. The fuselage geometry varied in cross-sectional shape and had two side-mounted, flow-through, half-axisymmetric inlets. Twin vertical tails were attached to the fuselage. The four planforms tested were a 65 deg delta wing, a combination of a 20 deg trapezoidal wing and a 45 deg horizontal tail, a 70 deg/30 deg cranked wing, and a 70 deg/66 deg crank wing, where the angle values refer to the leading-edge sweep angle of the lifting-surface planform. Planform effects on a single fuselage representative of an advanced fighter aircraft were studied. Results show that the highly swept cranked wings exceeded the aerodynamic performance levels, at low lift coefficients, of the 65 deg delta wing and the 20 deg trapezoidal wing at trimmed and untrimmed conditions.

Wood, R. M.↗
DOE OSTI2021

Radiation effects on stress evolution and dimensional stability of large fusion energy structures

Here we assess the effects of neutron irradiation on the deformation and stress evolution of large-scale fusion energy structures. This is accomplished through non-linear finite element structural analysis of the coupled thermal and mechanical fields at the Beginning-Of-Life (BOL), at 45 dpa, and at 90 dpa. Radiation effects include volumetric swelling and the influence of radiation on the mechanical properties. The system studied here is a large section of a full inboard module of an integrated structure comprising the First Wall and Blanket (FW/B) of a Dual Cooled Lithium-Lead (DCLL) energy conversion unit in the Fusion Nuclear Science Facility (FNSF). The structural material is the ferritic/martensitic steel F82H. We analyze several radiation effects phenomena that can lead to significant impact on the mechanical design and lifetime of the structure. These include volumetric swelling effects on the assembly and disassembly of modules and the impact of spatial gradients in neutron damage and helium generation on deformation, stress evolution, and plastic strain accumulation. We show that the stress state is strongly influenced by the accumulation of swelling strains, radiation hardening and softening, and by spatial gradients in displacement damage and helium gas generation. Several key regions in the FW/B structure are identified where severe plastic strains accumulate and may be potential sites for failure, especially during cyclic reactor operations. We finally show that minimum gaps between Inboard (IB) blanket sectors must be present during assembly so as to avoid excessive stress and strain in FW/B modules critical regions and raising chances of failure. A range of structural displacements are shown, from as low as 4 mm at BOL for free side walls to as high as 46 mm at 90 dpa for fully constrained side walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Pressure-induced shift of effective Ce valence, Fermi energy and phase boundaries in CeOs 4 Sb 12

Abstract CeOs 4 Sb 12 , a member of the skutterudite family, has an unusual semimetallic low-temperature L -phase that inhabits a wedge-like area of the field H —temperature T phase diagram. We have conducted measurements of electrical transport and megahertz conductivity on CeOs 4 Sb 12 single crystals under pressures of up to 3 GPa and in high magnetic fields of up to 41 T to investigate the influence of pressure on the different H – T phase boundaries. While the high-temperature valence transition between the metallic H -phase and the L -phase is shifted to higher T by pressures of the order of 1 GPa, we observed only a marginal suppression of the S -phase that is found below 1 K for pressures of up to 1.91 GPa. High-field quantum oscillations have been observed for pressures up to 3.0 GPa and the Fermi surface of the high-field side of the H -phase is found to show a surprising decrease in size with increasing pressure, implying a change in electronic structure rather than a mere contraction of lattice parameters. We evaluate the field-dependence of the effective masses for different pressures and also reflect on the sample dependence of some of the properties of CeOs 4 Sb 12 which appears to be limited to the low-field region.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1982

Rough analysis of installation effects on turboprop noise

A rough analysis of noise from a propeller operated at angle of attack, and in the nonuniform flow due to a line vortex approximating a wing flow field suggests installation can significantly affect turboprop noise levels. On one side of the propeller, where the blades approach the horizontal plane from above, decreases of noise occur; while on the other side noise increases. The noise reduction is due to negative interference of steady and unsteady sources. An angle of attack, or distance between propeller and vortex, exists for which noise is a minimum.

Durbin, P. A.↗
NASA NTRS1984

A Method for Measuring the Effective Throughput Time Delay in Simulated Displays Involving Manual Control

The advent and widespread use of the computer-generated image (CGI) device to simulate visual cues has a mixed impact on the realism and fidelity of flight simulators. On the plus side, CGIs provide greater flexibility in scene content than terrain boards and closed circuit television based visual systems, and they have the potential for a greater field of view. However, on the minus side, CGIs introduce into the visual simulation relatively long time delays. In many CGIs, this delay is as much as 200 ms, which is comparable to the inherent delay time of the pilot. Because most GCIs use multiloop processing and smoothing algorithms and are linked to a multiloop host computer, it is seldom possible to identify a unique throughput time delay, and it is therefore difficult to quantify the performance of the closed loop pilot simulator system relative to the real world task. A method to address these issues using the critical task tester is described. Some empirical results from applying the method are presented, and a novel technique for improving the performance of GCIs is discussed.

Jewell, W. F.↗
NASA NTRS1933

The Effect of Spray Strips on a Model of the P3M-1 Flying Boat Hull

This note presents the results of a series of tests made in the N.A.C.A. tank on a one-sixth full-size model of the hull and side floats of the Navy P3M-1 flying boat for the purpose of finding a method of reducing the amount of spray thrown into the propellers of this craft when taking off and landing. The model was tested without spray strips and with five different spray-strip arrangements. The best arrangement was an improvement over the bare hull with no spray strips, but the improvement was not sufficient to be satisfactory with the propellers in the designed position.

Dawson, John R↗
NASA NTRS1975

A quantitative magnetospheric model derived from spacecraft magnetometer data

The model is derived by making least squares fits to magnetic field measurements from four Imp satellites. It includes four sets of coefficients, representing different degrees of magnetic disturbance as determined by the range of Kp values. The data are fit to a power series expansion in the solar magnetic coordinates and the solar wind-dipole tilt angle, and thus the effects of seasonal north-south asymmetries are contained. The expansion is divergence-free, but unlike the usual scalar potential expansion, the model contains a nonzero curl representing currents distributed within the magnetosphere. The latitude at the earth separating open polar cap field lines from field lines closing on the day side is about 5 deg lower than that determined by previous theoretically derived models. At times of high Kp, additional high-latitude field lines extend back into the tail. Near solstice, the separation latitude can be as low as 75 deg in the winter hemisphere. The average northward component of the external field is much smaller than that predicted by theoretical models; this finding indicates the important effects of distributed currents in the magnetosphere.

Mead, G. D.↗
NASA NTRS2023

Parameter Dependencies of Early-Stage Tangential Discontinuity-Driven Foreshock Bubbles in Local Hybrid Simulations

Foreshock bubbles (FBs) are significant foreshock transients that can accelerate particles and disturb the magnetosphere-ionosphere system. In the kinetic formation model, foreshock ions interact with the discontinuity by performing partial gyrations to generate currents that change the magnetic field topology around the discontinuity. However, how different foreshock ion properties affect the growth of the field variations is not well understood. Therefore, we use 2-D local hybrid simulations to study the effects of different foreshock ion distributions and properties on the growth of tangential discontinuity (TD)-driven FBs. We discover that for a gyrophase-bunched distribution with an initial phase where the guiding center is on the other side of the TD, the foreshock ions gyrate together across the TD, causing more foreshock ions to cross the TD and leading to a faster expansion of the structure than for a Maxwellian distribution. A ring distribution also yields higher expansion speeds because of the higher projected velocity into the new perpendicular direction. For Maxwellian distributions, there are positive and linear correlations of the FB expansion speeds with the initial foreshock ion densities, thermal speeds, parallel speeds, and sine of the TD magnetic shear angles. These parameter dependencies grow in strength as the structures evolve with time. The foreshock ion distributions and properties that lead to stronger currents produce more significant magnetic field variations and higher expansion speeds. Our study helps quantify the formation and expansion of FBs to forecast their space weather effects and contribution to shock acceleration.

Andrew Vu↗
DOE OSTI2024

Unraveling the conundrum of electronic leakage in protonic ceramic cells: Operation-specific insights and rational design strategies

Electronic conduction through proton-conducting electrolytes significantly impairs the efficiency of protonic ceramic cells (PCCs). Here, in this study, we explore the electron and ion mixed transport properties of four common protonic ceramics, BaZr 0.8 Y 0.2 O 3-δ (BZY82), BaZr 0.7 Ce 0.2 Y 0.1 O 3-δ (BZCY721), BaZr 04 Ce 0.4 Y 0.1 Yb 0.1 O 3-δ (BZCYYb4411), and BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3-δ (BZCYYb1711). It marks the first instance of investigating these properties under operation-specific scenarios: fuel side of electrolysis cell, air side of electrolysis cell, fuel side of fuel cell, and air side of the fuel cell. BZCYYb1711 exhibits the highest ionic conductivity, but two to three times higher electronic leakage when exposed to oxygen-containing environments than the others. BZY82 exhibits approximately two times higher electronic leakage in a hydrogen-containing environment. BZCY721 demonstrates excellent ion transport numbers (~0.95) across these four operating conditions. BZCYYb4411 behaves quite similarly to BZCY721. The most challenging operating environment for all candidates is the air side of fuel cell mode. This mode leads to a high initial electronic leakage, followed by a significant increase with polarization. The probable cause for this behavior is a H 2 -free, polarization-induced reduction that leads to the formation of V$^•_O$. The electron small polaron associated with V$^•_O$ is released by the electrical field due to the Poole-Frenkel effect. ZnO and NiO sintering aids are found to be detrimental to the ionic conductivity of the electrolytes. In particular, NiO substantially lowers the ion transport number. The correlation of the operation-specific electronic leakage to full cells is discussed. It is suggested that a rational PCC design should synergistically couple BZCYYb1711 at fuel side with BZCY4411 at air side to deliver a well-balanced performance and faradaic efficiency simultaneously, and the high temperature sintering process with a NiO fuel electrode should be shortened or replaced by ultra-fast sintering techniques or using a fuel electrode scaffold-infiltration fabrication strategy.

42 ENGINEERING↗
DOE OSTI2025

Chiral edge state control of thermoelectric effects

Thermoelectric responses in two-dimensional electron gases subjected to magnetic fields have the potential to provide unique information about quasiparticle statistics. In this study, we show that chiral edge states play a key role in thermoelectric Hall bar measurements by completely controlling the direction of the internal thermal gradient. To this end, we perform measurements of the magnetothermoelectric responses of cadmium arsenide quantum wells. The magnetothermoelectric responses in the quantum Hall regime agree with theoretical predictions if one considers the role of chiral edge states, which flow in opposite directions on either side of the Hall bar and establish an internal temperature gradient that is perpendicular to the externally applied thermal gradient. We show that the results are self-consistent within this picture under different measurement conditions. We discuss potential applications of the findings, such as in nanoscale control of local temperature gradients and thermoelectric effects along with the characterization of other topological systems with chiral edges states.

Science & Technology - Other Topics↗
DOE OSTI2026

Evaluations of Connectors, Inlets, and Adapters on Side-Load and Withstand Force

This report examines the mechanical forces that direct current fast charging (DCFC) electric vehicle supply equipment (EVSE) connectors and electric vehicle (EV) inlet ports experience during normal usage. As we witness the fast and growing variety of EVs, charge port locations, and bigger and more powerful EVSE configurations including the SAE J3400 North American Charging Standard (NACS), which has increased the use of adapters with J3400 and J1772 compatibility. These new conditions contribute to increased mechanical forces due to their size, weight and lever arm effect, which creates the need to study and compare these forces to the limits on UL2251 and IEC 62196-1 standards. This report focuses solely on high power DC charging EVSE connectors, EV inlets and adapters for the specific compatibility cases on J3400 with J1772. We first describe the details of the 100N and the 750N side-load evaluations as described in the standards, then present the data obtained by replicating these tests to finally go into more detail on the findings and our recommendations.

100N↗
NASA NTRS2006

A Numerical Study of Hurricane Erin (2001): Model Verification and Storm Evolution - Part 1

The fifth-generation Pennsylvania State University National Center for Atmospheric Research (PSU NCAR) Mesoscale Model (MM5) is used to simulate Hurricane Erin (2001) at high resolution (4-km spacing) from its early development as a tropical depression on 7 September 2001, through a period of rapid intensification into a strong hurricane (8 9 September), and finally into a stage during which it maintains its intensity on 10 September. These three stages of formation, intensification, and maintenance in the simulation are in good agreement with the observed evolution of Erin. The simulation shows that during the formation and early portions of the intensification stages, intensification is favored because the environmental wind shear is weak and the system moves over a warm tongue of water. As Erin intensifies, the wind shear gradually increases with the approach of an upper-level trough and strengthening of a low-level high pressure system. By 10 September, the wind shear peaks and begins to decrease, the storm moves over slightly cooler waters, and the intensification ends. Important structural changes occur at this time as the outer precipitation shifts from the northeastern and eastern sides to the western side of the eye. A secondary wind maximum and an outer eyewall begin to develop as precipitation begins to surround the entire eye. The simulation is used to investigate the role of vertical wind shear in the changes of the precipitation structure that took place between 9 and 10 September by examining the effects of changes in storm-relative flow and changes in the shear-induced tilt. Qualitative agreement is found between the divergence pattern and advection of vorticity by the relative flow with convergence (divergence) generally associated with asymmetric inflow (outflow) in the eyewall region. The shift in the outer precipitation is consistent with a shift in the low-level relative inflow from the northeastern to the northwestern side of the storm. The changes in the relative flow are associated with changes in the environmental winds as the hurricane moves relative to the upper trough and the low-level high pressure system. Examination of the shear-induced tilt of the vortex shows that the change in the tilt direction is greater than that of the shear direction as the tilt shifts from a northerly orientation to northwesterly. Consistent with theory for adiabatic vortices, the maximum low-level convergence and upper-level divergence (and the maximum upward motion) occurs in the direction of tilt. Consequently, both mechanisms may play roles in the changes in the precipitation pattern.

Wu, Liguang↗
DOE OSTI2020

Engineering a disulfide-gated switch in streptavidin enables reversible binding without sacrificing binding affinity

Although high affinity binding between streptavidin and biotin is widely exploited, the accompanying low rate of dissociation prevents its use in many applications where rapid ligand release is also required. To combine extremely tight and reversible binding, we have introduced disulfide bonds into opposite sides of a flexible loop critical for biotin binding, creating streptavidin muteins (M88 and M112) with novel disulfide-switchable binding properties. Crystal structures reveal how each disulfide exerts opposing effects on structure and function. Whereas the disulfide in M112 disrupts the closed conformation to increase k off , the disulfide in M88 stabilizes the closed conformation, decreasing k off 260-fold relative to streptavidin. The simple and efficient reduction of this disulfide increases k off 19,000-fold, thus creating a reversible redox-dependent switch with 70-fold faster dissociation kinetics than streptavidin. The facile control of disulfide formation in M88 will enable the development of many new applications requiring high affinity and reversible binding.

59 BASIC BIOLOGICAL SCIENCES↗